Page 1
FLX15
FLX10
FLEX ARM
Published 2006-05-30 S/N A10100128508 - A10100152509 Part No. A101TG010P
PARTS MANUAL
An Operators Manual with IMPORTANT Safety, Assembly, Operation
and Maintenance information was packaged with this Parts Manual
during final inspection at the factory. If the Operators Manual is
missing at any time, please contact Tiger Corporation to receive your
free replacement manual.
Tiger Corporation
3301 N. Louise Ave.
Sioux Falls, SD 57107
1-800-843-6849
1-605-336-7900
www.tiger-mowers.com
© 2006 Alamo Group Inc.
Page 2
PARTS ORDERING GUIDE
The following instructions are offered to help eliminate delay and error in processing purchase
orders for the equipment in this section.
1. The Purchase Order must include the name and address of the person or organization ordering
the parts, who should be charged, and if possible, the serial number of the machine for which the
parts were ordered.
2. The Purchase Order must clearly list the quantity of each part, the complete and correct par t
number, and the description of the part.
3. The Manufacturer reserves the right to substitute parts where applicable.
4. The Manufacturer reserves the right to change prices without prior notice.
NOTE: Please refer to the Safety Section in the front of the Operators Manual for the proper
Part Number when ordering Replacement Safety Decals. Safety decals are
available free of charge from the Manufacturer.
NOTE: If the Operators Manual does not accompany this Parts Manual please obtain one,
free of charge from the Manufacturer. DO NOT operate this implement unless you
READ, UNDERSTAND, and FOLLOW the Safety and Operation instructions
contained in the Operators Manual
NOTE: Please note that the appearance of some parts may vary from the artwork shown
in the Manual.
For maximum safety and to guarantee optimum product reliability, always use genuine
OEM Parts. The use of inferior replacement parts may cause premature or
catastrophic failure which could result in serious injury or death. Direct any questions
regarding parts to:
Tiger Corporation
3301 N. Louise Ave.
Sioux Falls, SD 57107
1-800-843-6849
1-605-336-7900
www.tiger-mowers.com
-6-2-
Page 3
TABLE OF CONTENTS
HITCH ASSEMBLY .................................................................6-4
PRECISION CLEVIS ................................................................6-5
PRECISION HITCH .................................................................6-6
BEARING MOUNT ASSEMBLY ........................................................6-7
ARM ASSEMBLY ...................................................................6-8
FRAME ASSEMBLY ...............................................................6-10
CASTOR FRAME ASSEMBLY .......................................................6-12
CASTOR WHEEL ASSEMBLY .......................................................6-13
HUB & TIRE ASSEMBLY ............................................................6-14
HITCH JACK, 10" SIDE WIND (232-500) ...............................................6-15
SAFETY TOW CHAIN (S000-010) .....................................................6-16
TRANSPORT LIGHT KIT............................................................6-17
HYDRAULIC CIRCUIT ..............................................................6-18
HYDRAULIC CYLINDER ............................................................6-20
HYDRAULIC SELECTOR VALVE, FLX15 (A101-350) .....................................6-21
HYDRAULIC SELECTOR VALVE, FLX10 (A102-350) .....................................6-22
HYDRAULIC SELECTOR VALVE, SWITCH & HARNESS ..................................6-23
DRIVELINE REFERENCE...........................................................6-24
SFT SAFETY SHIELDS.............................................................6-24
DRIVE SHAFT, IMPLEMENT, 1-3/4 Z20 SIZE 8 (340-841) ..................................6-25
CROSS SHAFT, FLX15, 1-3/4 Z20 SIZE 8 (340-842) ......................................6-26
CROSS SHAFT, FLX10, 1-3/4 Z20 SIZE 8 (340-843) ......................................6-27
JACK SHAFT,1-3/4 Z20 SIZE 8 (340-844) ..............................................6-28
GEARBOX,1:1, BP#S2100100083 (330-556) ............................................6-29
PARTS INDEX ....................................................................6-30
6-3
Page 4
HITCH ASSEMBLY
Ref. Part No. Description Qty.
1 A101-110 Hitch frame 1
2 A101-145 Pin, hitch frame 1
3 256-011 Washer, 1/2" 4
4 250-057 Bolt, 1/2" x 2" UNC 1
5 270-007 Locknut, 1/2" UNC 4
6 256-0533 Machine bushing, 2" x 3" x 10ga 1
7 A101-171 Hitch Swivel - *sold with 774-012 1
774-012 Weld sleeve - *sold with A101-171 1
8 A101-112 Sleeve sub-assembly 1
9 250-107 Bolt, 3/4" x 6" UNC 2
10 250-127 Bolt, 1" x 2-1/2" UNC 1
11 270-002 Locknut, 1" UNC 1
12 256-0011 Washer, 1" x 1/4" Thick 1
13 S000-010 Safety chain - *attachment link shown only 1
14 C502-107 Hitch Clevis 1
15 270-001 Locknut, 3/4" UNC 2
16 262-004 Roll pin, 3/8" x 3" 1
17 232-500 Hitch jack, 10" side wind 1
18 362-011 Tension bushing, 1" x 1-1/4" x 1-1/2" 1
19 273-006 Grease nipple, self tap 2
20 CS01-134 Pin, 1" x 4 5/8", 4 11/16" U.L. 1
21 256-001 Washer, 1" plated SAE 1
22 262-006 Roll Pin, 3/8" x 2" Plated 1
23 250-060 Bolt, 1/2" x 1-3/4" UNC Gr 5 Plated 1
24 A101-364 Mount, PTO Stand 1
25 C000-132 Stand, Power Shaft 1
26 250-059 Bolt, 1/2" x 1-3/4" UNC Gr 5 Plated 2
27 229-010 Compression Spring, 1/2" x 1.5" LG 1
28 271-008 Cotter Pin, 1/8" x 1 Plated 1
FLX15/10 09/05 6-4
Page 5
PRECISION CLEVIS (C000-360)
Ref. Part No. Description Qty.
1 C000-360 Hitch block 1
2 362-015 Tension bushing, 1" x 1-1/4" x 1" lg 2
3 C000-363 Wear plate 1
4 C000-362 Spacer plate 6
5 255-005 Lockwasher, 5/8" 2
6 250-090 Bolt, 5/8" x 2" UNC 2
FLX15/10 09/05 6-5
Page 6
PRECISION HITCH (C000-300)
Ref. Part No. Description Qty.
1 250-109 Bolt, 3/4 x 5-1/2 UNC 2
2 250-059 Bolt, ½ x 1-1/2 UNC 1
3 C000-202 Bolt, 1-1/8 x 5-1/2 UNF 1
4 C000-303 Drawbar clevis top 1
5 C000-301 Hitch tongue 1
6 273-001 Grease nipple, 1/8 NPT 3
7 C000-305 Spacer 1
8 C000-302 Draw bar clevis base 1
9 257-003 Lock nut, 1-1/8 UNF 1
10 C000-304 Clamp bar 1
11 270-001 Lock nut, 3/4 UNC 2
12 255-009 Lock washer, ½ 1
13 271-011 Cotter pin, 1/4 x 2-1/2 1
14 256-0712 Machine Bushing Spacer 1
(Only required if Hitch tongue is tight)
FLX15/10 09/05 6-6
Page 7
BEARING MOUNT ASSEMBLY
Ref. Part No. Description Qty.
1 264-004 Retaining ring, internal 1
2 356-310 Locking Collar / Bearing set 1
3 A101-150 Bearing holder 1
4 A101-152 Rubber ring, vibration isolator 2
5 A101-153 Bearing stand 1
6 A101-155 Washer, 4-1/16" x 7 ga 1
7 264-014 Retaining ring, external 1
8 A101-154 Shield 1
9 270-007 Locknut, 1/2" UNC 4
10 256-011 Washer, 1/2" 2
11 250-057 Bolt, 1/2" x 2" UNC 2
12 273-006 Grease nipple, self tap 2
13 250-127 Bolt, 1" x 2-1/2" UNC 2
14 250-060 Bolt, 1/2" x 1-3/4" UNC 2
15 270-002 Locknut, 1" UNC 2
16 271-006 Cotter pin, 3/16" x 2" 1
17 257-009 Hex slotted nut, 1" UNC 1
18 256-001 Washer, 1" SAE type 1
19 A101-156 Bearing stand mount 1
20 256-017 Washer, 3/8" 4
21 250-018 Bolt, 3/8" x 1" UNC 4
22 255-013 Lockwasher, 3/8" 4
23 341-6241 SFT shield 1
24 A101-157 Spacer, 1.151" Long 1
A101-158 Spacer, 0.871" Long 1
NOTE: USE LONG SPACER (ITEM 24, 1.151" LONG) FIRST AND IF TOO LONG TO
ALLOW THE TRACTOR SHAFT TO BOLT ON USE SHORT SPACER (0.871" LONG)
FLX15/10 09/05 6-7
Page 8
ARM ASSEMBLY
FLX15/10 09/05 6-8
Page 9
ARM ASSEMBLY
Ref. Part No. Description Qty.
1 262-004 Roll pin, 3/8" x 3" 1
2 256-3533 Machine bushing, 2" x 3" x 10ga 1
3 362-011 Tension bushing, 1" x 1-1/4" x 1-1/2" long 3
4 A101-141 Pin, arm assembly 1
5 273-011 Grease nipple, 90° self tap 2
6 250-0542 Bolt, 1/2" x 2-1/4" UNC 2
7 256-011 Washer, 1/2" 6
8 270-007 Locknut, 1/2" UNC 3
9 A101-136 Hydraulic hose stand 2
10 270-017 Locknut, 3/8" UNC 14
11 250-025 Bolt, 3/8" x 2-1/4" UNC 9
12 273-006 Grease nipple, self tap 6
13 A101-143 Pin, gearbox mount 1
14 256-018 Washer, 1/4" 2
15 250-002 Bolt, 1/4" x 1" UNC 2
16 280-201 Manual canister 1
17 250-026 Bolt, 3/8" x 2-1/2" UNC 1
18 A101-363 Manual canister mount 1
19 250-0261 Bolt, 3/8" x 2-3/4" UNC 1
20 270-025 Locknut, 1/4" UNC 2
21 A101-362 Hose arm mount 1
22 A101-139 Hose clamp 3
23 250-046 Bolt, 1/2" x 5" UNC 1
24 A101-361 Hose arm 1
25 250-018 Bolt, 3/8" x 1" UNC 1
26 362-019 Tension bushing, 2" x 2-1/4" x 1" long 2
27 A101-105 Arm 1
28 255-005 Lock washer, 5/8" 4
29 250-093 Bolt, 5/8" x 1-3/4" UNC 4
30 A101-108 Gearbox mounting arm 1
31 362-0121 Tension bushing, 1-1/2" x 1-3/4" x 1" long 2
32 A101-147 Pin, strut 4
33 A101-126 Strut, hitch 1
34 250-063 Bolt, 1/2" x 1" UNC 4
35 255-009 Lock washer, 1/2" 4
36 A101-127 Strut, frame 1
37 330-556 Gearbox 1
38 362-015 Tension bushing, 1" x 1-1/4" x 1" long 1
FLX15/10 09/05 6-9
Page 10
FRAME ASSEMBLY
FLX15/10 09/05 6-10
Page 11
FRAME ASSEMBLY
Ref. Part No. Description Qty.
1 A101-101 FLX15 Main frame 1
A102-101 FLX10 Main frame *not shown 1
2 362-0121 Tension bushing, 1-1/2" x 1-3/4" x 1" long 3
**not required on FLX10
3 250-025 Bolt, 3/8" x 2-1/4" UNC 8
4 270-017 Locknut, 3/8" UNC 15
5 A101-137 Transport light mount 1
6 270-020 Locknut, 5/16" UNC 2
7 256-020 Washer, 5/16" 2
8 250-007 Bolt, 5/16" x 1" UNC 2
9 S000-073 Transport light kit *left light shown only 1
10 A101-139 Hose clamp 2
11 250-026 Bolt, 3/8" x 2-1/2" UNC 5
12 A101-136 Hydraulic hose stand 2
13 362-019 Tension bushing, 2" x 2-1/4" x 1" long 2
14 273-006 Grease nipple, self tap 5
15 362-015 Tension bushing, 1" x 1-1/4" x 1" long 1
16 A101-164 Driveline shipping/ storage bracket 2
17 250-019 Bolt, 3/8" x 1-1/4" UNC 2
18 A101-135 Hydraulic breakaway stand 1
19 A101-165 Driveline shipping/ storage clamp 2
20 256-017 Washer, 3/8" 2
21 330-556 Gearbox 1
22 255-005 Lock washer, 5/8" 4
23 250-095 Bolt, 5/8" x 1-1/2" UNC 4
24 250-105 Bolt, 3/4" x 7-1/2" UNC 2
25 270-001 Locknut, 3/4" UNC 2
26 250-063 Bolt, 1/2" x 1" UNC 1
27 255-009 Lock washer, 1/2" 1
28 256-011 Washer, 1/2" 1
29 A101-149 Pin, cutter hitch 1
31 A101-133 Hitch tongue, rotary cutter 1
32 262-005 Roll pin, 3/8" x 2-1/2" 1
33 256-0552 Machine bushing, 1-1/2" x 2-1/4" x 10ga. 1
34 A101-132 Hitch clevis, rotary cutter 1
35 270-002 Locknut, 1" UNC 3
36 S000-010 Safety chain - *attachment link shown only 1
37 256-002 Washer, 1" AS type 1
38 250-127 Bolt, 1" x 2-1/2" UNC 1
39 250-145 Bolt, 1" x 4" UNC 2
40 A101-130 Link adjustment rod 1
41 A101-131 Link adjustment body 1
42 362-011 Tension bushing, 1" x 1-1/4" x 1-1/2" long 1
FLX15/10 09/05 6-11
Page 12
CASTOR FRAME ASSEMBLY (FLX15 ONLY)
Ref. Part No. Description Qty.
1 A101-104 Castor frame 1
2 256-011 Washer, 1/2" 3
3 250-057 Bolt, 1/2" x 2" UNC 1
4 273-006 Grease nipple, self tap 1
5 A101-144 Pin, castor frame 1
6 A101-146 Pin, castor link 2
7 273-011 Grease nipple, 90° self tap 2
8 250-063 Bolt, 1/2" x 1" UNC 2
9 255-009 Lock washer, 1/2" 2
10 256-001 Washer, 1" SAE type 2
11 262-006 Roll pin, 3/8" x 2" 2
12 362-011 Tension bushing, 1" x 1-1/4" x 1-1/2" long 1
13 262-005 Roll pin, 3/8" x 2-1/2" 1
14 256-0552 Machine bushing, 1-1/2" x 2-1/4" x 10ga. 1
15 270-007 Locknut, 1/2" UNC 1
16 A101-125 Castor link 1
FLX15/10 09/05 6-12
Page 13
CASTOR WHEEL ASSEMBLY
Ref. Part No. Description Qty.
1 257-014 Jam nut, 3/4" UNF 2
2 256-510 Belville washer, 60 x 20.5 x 2.5mm 2
3 256-003 Washer, 3/4" 1
4 A101-122 Castor washer 1
5 A101-123 Castor spacer 1
6 364-001 Nylatron bushing, 2-1/2" x 3" x 2" long 2
7 273-006 Grease nipple, self tap 2
8 270-001 Locknut, 3/4" UNC 1
9 A101-124 Nylon castor disc 1
10 A101-120 Castor 1
11 250-114 Bolt, 3/4" x 2-1/2" UNC 1
12 208-026 Spindle, S618, 2" x 14-7/8" 1
13 250-050 Bolt, 1/2" x 3-1/2" UNC 1
14 270-007 Locknut, 1/2" UNC 1
* Refer to the Assembly Section in the front of this Manual for Belville washer orientation
FLX15/10 09/05 6-13
Page 14
HUB & TIRE ASSEMBLY
Ref. Part No. Description Qty.
1 206-003 Hub, H618 complete, includes ref #2-11 1
2 207-018 Seal 1
3 207-013 Bearing 1
4 207-014 Race 1
5 273-002 Grease nipple, 45° 1/8" NPT 1
6 207-016 Race 1
7 207-015 Bearing 1
8 209-010 Washer, 1" 1
9 209-011 Castle nut, 1"-14 UNS 1
10 271-005 Cotter pin, 3/16" 1
11 207-017 Dust cap 1
12 257-032 Nut, 3/8" UNC 10
13 255-013 Lock washer, 3/8" 10
14 201-016 Rim half 2
15 210-011 Tire only 1
16 211-013 Tube 1
17 250-018 Bolt, 3/8" x 1" UNC 10
18 210-178 Aircraft tire, 31x 13 x 12 x 20 ply, complete
includes ref #12-17 1
19 255-007 Lock Washer, 9/16" 6
20 250-073 Bolt, 9/16" x 1-1/2" UNF 6
21 207-011 Wheel Bolt, 9/16" x 1-3/4" UNF 6
NOTE: IF RIM HOLES ARE TAPERED USE WHEEL BOLT 207-011(# 21). IF RIM HOLES ARE
FLAT USE BOLT 250-073 (# 20) AND LOCK WASHER 255-007 (# 19).
FLX15/10 09/05 6-14
Page 15
HITCH JACK, 10" SIDE WIND (232-500)
Ref. Part No. Description Qty.
1 232-651 Gear cover 1
2 232-652 Bushing 2
3 232-653 Gear 2
4 232-654 Bolt, 1/4" x 3" UNC 2
5 232-655 Nut, 1/4" UNC 2
6 232-656 Pin, long 1
7 232-657 Handle 1
8 232-658 Washer, 1/2" x 1-1/2" 1
9 232-659 Lock pin & chain 1
10 232-660 Pin, long 1
11 232-661 Main body 1
12 232-662 Washer, 1/2" x 1-5/16" x 10ga 1
13 232-663 Washer, 1/2" x 1-1/16" 2
14 232-664 Felt bushing 1
15 232-665 Bearing 1
16 232-666 Washer, 1/2" x 1-1/16" x 7ga 1
17 232-667 Acme screw 1
18 232-668 Stand body 1
19 232-669 Acme nut 1
FLX15/10 09/05 6-15
Page 16
SAFETY TOW CHAIN (S000-010)
NOTE: This safety chain is intended as an auxiliary attaching system per ASAE S338.3. The safety chain help
control the flex arm should it accidentally separate from the drawbar, or the rotary cutter should it accidentally
separate from the flex arm. Do not use the safety chain for towing. Replace the entire chain if any link or
end fitting is broken, damaged or stretched.
Ref. Part No. Description Qty.
1 S000-010 Safety tow chain, 10,000 lbs capacity
59" minimum length 2
2 250-127 Bolt, 1" x 2-1/2" UNC 2
3 256-0011 Washer, 1" x 1/4" Thick 2
4 270-002 Locknut, 1" UNC 2
FLX15/10 09/05 6-16
Page 17
TRANSPORT LIGHT KIT
The lights are to be mounted with the red and amber facing to the rear, with the outside light being the amber.
Ref. Part No. Description Qty.
1 S000-073 Light set, left and right dual lights FLX15
Includes a 7 pin ag plug, & harness 1
S000-072 Light set, left and right dual lights FLX10
Includes a 7 pin ag plug, & harness 1
2 270-017 Locknut, 3/8" UNC 4
3 S000-046 Rear beam light mount 1
4 258-111 U-bolt, 5" x 6" x 3/8" UNC XH1500/XH1000 1
258-1101 U-bolt, 4 x 4-3/4" x 3/8" UNC S150/S100 1
5 250-007 Bolt, 5/16" x 1" UNC 4
6 256-020 Washer, 5/16" 4
7 270-020 Locknut, 5/16" UNC 4
8 A101-137 Light mount 1
9 250-025 Bolt, 3/8" x 2-1/4" UNC 1
10 250-026 Bolt, 3/8" x 2-1/2" UNC 1
FLX15/10 09/05 6-17
Page 18
HYDRAULIC CIRCUIT
FLX15/10 09/05 6-18
Page 19
HYDRAULIC CIRCUIT
Ref. Part No. Description Qty.
1 111-260 Hydraulic hose, 230" M - M, FLX15 4
111-257 Hydraulic hose, 200" M - M, FLX10 3
2 111-258 Hydraulic hose, 250" M - F, FLX15 1
111-259 Hydraulic hose, 223" M - F, FLX10 1
3 111-261 Hydraulic hose, 230" M - F, FLX15 1
111-195 Hydraulic hose, 203" M - F, FLX10 1
4 302-015 Clevis pin, 1" x 2-7/8" UL 2
5 100-3102 Hydraulic cylinder, 24" stroke, FLX15 1
100-3077 Hydraulic cylinder, 20" stroke, FLX10 1
6 256-001 Washer, 1" SAE type 7
8 250-063 Bolt, 1/2" x 1" UNC 1
9 255-009 Lock washer, 1/2" 1
10 256-011 Washer, 1/2" 1
11 A101-148 Pin, cylinder guard 1
12 262-006 Roll pin, 3/8" x 2" 1
13 A101-140 Transport lock pin 1
14 A101-129 Cylinder guard outer, FLX15 1
A102-129 Cylinder guard outer, FLX10 1
15 271-005 Cotter pin, 3/16" x 1-1/2" 2
16 300-012 Lynch pin, 1/4" standard 1
17 A101-128 Cylinder guard inner, FLX15 1
A102-128 Cylinder guard inner, FLX10 1
18 264-013 Retaining ring
FLX15 8
FLX10 6
19 108-064 Coupler, female
FLX15 4
FLX10 3
20 108-065 Coupler plug
FLX15 4
FLX10 3
21 108-043 Elbow, 90° M - M 2
FLX15/10 09/05 6-19
Page 20
HYDRAULIC CYLINDER
100-3077 RAM-LOK, 3" bore x 20" stroke w/ 4" stop tube
Location: FLX10
100-3102 RAM-LOK 3" bore x 24" stroke
Location: FLX15
Ref. Part No. Description Qty.
1 102-280 Butt clevis 1
2 102-281 Piston nut 1
3 102-283 Piston 1
4 102-282 Retaining wire 2
5 102-285 Barrel, 24" FLX15 1
102-290 Barrel, 20" FLX10 1
6 102-287 Rod clevis 1
7 102-284 Rod, 24" FLX15 1
102-289 Rod, 20" FLX10 1
8 102-286 Cylinder head 1
9 102-288 Seal kit 1
10* 102-291 Stop tube FLX10 only 1
FLX15/10 09/05 6-20
Page 21
HYDRAULIC SELECTOR VALVE, FLX15 (A101-350)
This optional kit reduces the required tractor ports and provides independent double acting wing lift action.
Ref. Part No. Description Qty.
1 111-203 Hydraulic hose, 103" M - F 2
2 108-067 Elbow, 90° Male NPT - Female NPT 2
3 108-068 Extension Male ORB - Female NPT 2
4 108-066 Elbow, 90° Male ORB - Female NPT 2
5 127-015 Selector valve 1
6 270-025 Locknut, 1/4" UNC 2
7 111-260 Hydraulic hose, 230" M - M 2
8 111-260 Supplied with Flex Arm 2
9 250-003 Bolt, 1/4" x 2-1/2" UNC 2
10 264-013 Retaining ring 4
11 108-065 Coupler plug 2
12 108-064 Coupler, female 2
13 111-176 Hydraulic hose, 213" M - F 2
14 108-043 Elbow, 90° ORB 2
15 128-080 Replacement Solenoid 1
16 276-312 Harness assembly 1
17 276-300 Switch assembly 1
18 108-044 Elbow, 45° Male ORB - Male NPT 2
FLX15/10 09/05 6-21
Page 22
HYDRAULIC SELECTOR VALVE, FLX10 (A102-350)
This optional kit reduces the required tractor ports and provides double acting wing lift action.
Ref. Part No. Description Qty.
1 111-203 Hydraulic hose, 103" M - F 2
2 108-067 Elbow, 90° Male NPT - Female NPT 2
3 108-068 Extension Male ORB - Female NPT 2
4 108-066 Elbow, 90° Male ORB - Female NPT 2
5 127-015 Selector valve 1
6 270-025 Locknut, 1/4" UNC 2
7 111-257 Hydraulic hose, 200" M - M 1
8 111-257 Supplied with Flex Arm 3
9 250-003 Bolt, 1/4" x 2-1/2" UNC 2
10 264-013 Retaining ring 2
11 108-065 Coupler plug 1
12 108-064 Coupler, female 1
13 111-176 Hydraulic hose, 213" M - F 1
14 108-043 Elbow, 90° ORB 1
15 128-080 Replacement Solenoid 1
16 276-312 Harness assembly 1
17 276-300 Switch assembly 1
18 108-044 Elbow, 45° Male ORB - Male NPT 2
FLX15/10 09/05 6-22
Page 23
HYDRAULIC SELECTOR VALVE, SWITCH & HARNESS
Ref. Part No. Description Qty.
1 276-299 Switch box 1
2 276-298 Switch harness 1
3 276-312 Solenoid harness 1
4 275-001 Toggle switch, complete 1
5 275-010 Replacement fuse 1
6 276-297 Jumper cable 1
7 276-296 Power harness 1
8 276-300 Complete switch & harness, incl. 1,2,4,5,6,7
FLX15/10 09/05 6-23
Page 24
DRIVELINE REFERENCE
Ref. Part No. Description Qty.
1 341-6238 SFT safety shield,
2 340-841 Drive shaft, implement 1
3 340-842 Cross shaft, FLX15 1
340-843 Cross shaft, FLX10 1
4 340-844 Jack shaft 1
5 341-6241 SFT safety shield,
6 CV Assembly - Supplied with Rotary Cutter 1
i230mm 4
i252mm 1
SFT SAFETY SHIELDS
Ref. Part No. Description Qty.
1 250-017 Bolt, 3/8" x 3/4" UNC 4
2 255-013 Lock washer, 3/8" 4
3 256-017 Washer, 3/8" 4
4 SFT safety shield - See driveline reference 1
FLX15/10 09/05 6-24
Page 25
DRIVE SHAFT, IMPLEMENT, 1-3/4 Z20 SIZE 8 (340-841)
340-841 Location: FLX15/ FLX10 Frame Gearbox to Cutter
Ref. Part No. Description Qty.
1 341-0863 Yoke 1
2 341-645 Cross journal c/w snap rings 2
3 341-603 Grease nipple, 45
4 341-744 Flexible pin 1
5 341-769 Outer yoke 1
6 341-8143 Outer tube 1
7 341-0815 Ring nut 1
8 341-8142 Inner tube 1
9 341-8017 Flexible pin 1
10 341-0805 Inner yoke 1
11 341-802 Tapered pin kit 2
12 341-637 Shield bearing, outer shield 1
13 341-776 Outer cone set 1
14 341-8141 Outer shield 1
15 341-8140 Inner shield 1
16 341-8008 Inner cone set 1
17 341-642 Shield bearing, inner shield 1
18 341-8164 Inner half c/w shields 1
19 341-8163 Outer half c/w shields 1
20 341-8165 Complete shield set 1
o
2
FLX15/10 09/05 6-25
Page 26
CROSS SHAFT, FLX15, 1-3/4 Z20 SIZE 8 (340-842)
FLX15 ONLY
340-842 Location: FLX15 Frame Gearbox to Arm Gearbox
Ref. Part No. Description Qty.
1 341-0863 Yoke 1
2 341-645 Cross journal c/w snap rings 2
3 341-603 Grease nipple, 45
4 341-744 Flexible pin 1
5 341-769 Outer yoke 1
6 341-8147 Outer tube 1
7 341-0815 Ring nut 1
8 341-8146 Inner tube 1
9 341-8017 Flexible pin 1
10 341-0805 Inner yoke 1
11 341-802 Tapered pin kit 2
12 341-637 Shield bearing, outer shield 1
13 341-776 Outer cone set 1
14 341-8145 Outer shield 1
15 341-8144 Inner shield 1
16 341-8008 Inner cone set 1
17 341-642 Shield bearing, inner shield 1
18 341-8161 Inner half c/w shields 1
19 341-8160 Outer half c/w shields 1
20 341-8162 Complete shield set 1
o
2
FLX15/10 09/05 6-26
Page 27
CROSS SHAFT, FLX10, 1-3/4 Z20 SIZE 8 (340-843)
FLX10 ONLY
340-843 Location: FLX10 Frame Gearbox to Arm Gearbox
Ref. Part No. Description Qty.
1 341-0863 Yoke 1
2 341-645 Cross journal c/w snap rings 2
3 341-603 Grease nipple, 45
4 341-744 Flexible pin 1
5 341-769 Outer yoke 1
6 341-8151 Outer tube 1
7 341-0815 Ring nut 1
8 341-8150 Inner tube 1
9 341-8017 Flexible pin 1
10 341-0805 Inner yoke 1
11 341-802 Tapered pin kit 2
12 341-637 Shield bearing, outer shield 1
13 341-776 Outer cone set 1
14 341-8149 Outer shield 1
15 341-8148 Inner shield 1
16 341-8008 Inner cone set 1
17 341-642 Shield bearing, inner shield 1
18 341-8167 Inner half c/w shields 1
19 341-8166 Outer half c/w shields 1
20 341-8168 Complete shield set 1
o
2
FLX15/10 09/05 6-27
Page 28
JACK SHAFT,1-3/4 Z20 SIZE 8 (340-844)
340-844 Location: FLX15/ FLX10 Arm Gearbox to Bearing
Ref. Part No. Description Qty.
1 341-0863 Yoke 1
2 341-645 Cross journal c/w snap rings 1
3 341-603 Grease nipple, 45
4 341-8017 Flexible pin 1
5 341-0805 Inner yoke 1
6 341-8155 Inner tube 1
7 341-0815 Ring nut 1
8 341-8154 Outer tube, 1-3/4 Z20 1
9 341-802 Tapered pin kit 1
10 341-642 Shield bearing, inner shield 1
11 341-8008 Inner cone set 1
12 341-8152 Inner shield 1
13 341-8153 Outer shield 1
14 341-8156 Outer cone set 1
15 341-637 Shield bearing, outer shield 1
16 341-8170 Inner half c/w shields 1
17 341-8169 Outer half c/w shields 1
18 341-8171 Complete shield set 1
o
1
FLX15/10 09/05 6-28
Page 29
GEARBOX,1:1, BP#S2100100083 (330-556)
Ref. Part No. Description Qty.
1 331-585 Housing 1
2 331-586 Shaft 1
3 331-581 Cover 1
4 331-562 Snap ring 1
5 331-552 Snap ring 2
6 331-587 Shim A/R
7 331-588 Shim A/R
8 331-9015 Ball bearing 2
9 331-564 Tapered roller bearing 1
10 331-575 Tapered roller bearing 1
11 331-589 Oil seal 2
12 331-559 Cap 1
13 331-590 Oil plug 1
14 331-561 Oil plug 2
15 331-591 Bevel gear set 1
FLX15/10 09/05 6-29
Page 30
PARTS INDEX
Part Number Page Part Number Page
100-3077 ......................... 19, 20
100-3102 ......................... 19, 20
102-280 ............................. 20
102-281 ............................. 20
102-282 ............................. 20
102-283 ............................. 20
102-284 ............................. 20
102-285 ............................. 20
102-286 ............................. 20
102-287 ............................. 20
102-288 ............................. 20
102-289 ............................. 20
102-290 ............................. 20
102-291 ............................. 20
108-043 ....................... 19, 21, 22
108-044 .......................... 21, 22
108-064 ....................... 19, 21, 22
108-065 ....................... 19, 21, 22
108-066 .......................... 21, 22
108-067 .......................... 21, 22
108-068 .......................... 21, 22
111-185 .......................... 21, 22
111-195 ............................. 19
111-203 .......................... 21, 22
111-257 .......................... 19, 22
111-258 ............................. 19
111-259 ............................. 19
111-260 .......................... 19, 21
111-261 ............................. 19
127-015 .......................... 21, 22
128-080 .......................... 21, 22
201-016 ............................. 14
206-003 ............................. 14
207-013 ............................. 14
207-014 ............................. 14
207-015 ............................. 14
207-016 ............................. 14
207-017 ............................. 14
207-018 ............................. 14
208-026 ............................. 13
209-010 ............................. 14
209-011 ............................. 14
210-011 ............................. 14
210-178 ............................. 14
211-013 ............................. 14
229-010 .............................. 4
232-500 ........................... 4, 15
232-651 ............................. 15
232-652 ............................. 15
232-653 ............................. 15
232-654 ............................. 15
232-655 ............................. 15
232-656 ............................. 15
232-657 ............................. 15
232-658 ............................. 15
232-659 ............................. 15
232-660 ............................. 15
232-661 ............................. 15
232-662 ............................. 15
232-663 ............................. 15
232-664 ............................. 15
232-665 ............................. 15
232-666 ............................. 15
232-667 ............................. 15
232-668 ............................. 15
232-669 ............................. 15
250-002 .............................. 9
250-003 .......................... 21, 22
250-007 .......................... 11, 17
250-017 ............................. 24
250-018 ......................... 7, 9, 14
250-019 ............................. 11
250-025 ........................ 9, 11, 17
250-026 ........................ 9, 11, 17
250-0261 ............................. 9
250-046 .............................. 9
250-050 ............................. 13
250-0542 ............................. 9
250-057 ......................... 4, 7, 12
250-059 ............................ 4, 6
250-060 ............................ 4, 7
250-063 ..................... 9, 11, 12, 19
250-074 ............................. 14
250-090 .............................. 5
250-093 .............................. 9
250-095 ............................. 11
250-105 ............................. 11
250-107 .............................. 4
250-109 .............................. 6
250-114 ............................. 13
250-127 ...................... 4, 7, 11, 16
250-145 ............................. 11
255-005 ......................... 5, 9, 11
255-007 ............................. 14
255-009 ................... 6, 9, 11, 12, 19
255-013 ........................ 7, 14, 24
256-001 ...................... 4, 7, 12, 19
256-0011 .......................... 4, 16
256-002 ............................. 11
256-003 ............................. 13
256-011 ................. 4, 7, 9, 11, 12, 19
256-017 ........................ 7, 11, 24
256-018 .............................. 9
256-020 .......................... 11, 17
256-0533 ............................. 4
256-0552 ......................... 11, 12
FLX15/10 09/05 6-30
Page 31
256-0712 ............................. 6
256-510 ............................. 13
257-003 .............................. 6
257-009 .............................. 7
257-014 ............................. 13
257-032 ............................. 14
258-1101 ............................ 17
258-111 ............................. 17
262-004 ............................ 4, 9
262-005 .......................... 11, 12
262-006 ........................ 4, 12, 19
264-004 .............................. 7
264-013 ....................... 19, 21, 22
264-014 .............................. 7
270-001 ...................... 4, 6, 11, 13
270-002 ...................... 4, 7, 11, 16
270-007 .................... 4, 7, 9, 12, 13
270-017 ........................ 9, 11, 17
270-020 .......................... 11, 17
270-025 ........................ 9, 21, 22
271-005 .......................... 14, 19
271-006 .............................. 7
271-008 .............................. 4
271-011 .............................. 6
273-001 .............................. 6
273-002 ............................. 14
273-006 .................... 4, 7, 9, 11-13
273-011 ........................ 9, 12, 19
275-001 ............................. 23
275-010 ............................. 23
276-296 ............................. 23
276-297 ............................. 23
276-298 ............................. 23
276-299 ............................. 23
276-300 .......................... 21-23
276-312 .......................... 21-23
280-201 .............................. 9
300-012 ............................. 19
302-015 ............................. 19
330-556 ........................ 9, 11, 29
331-552 ............................. 29
331-559 ............................. 29
331-561 ............................. 29
331-562 ............................. 29
331-564 ............................. 29
331-575 ............................. 29
331-581 ............................. 29
331-585 ............................. 29
331-586 ............................. 29
331-587 ............................. 29
331-588 ............................. 29
331-589 ............................. 29
331-590 ............................. 29
331-591 ............................. 29
331-9015 ............................ 29
340-841 .......................... 24, 25
340-842 .......................... 24, 26
340-843 .......................... 24, 27
340-844 .......................... 24, 28
341-0805 ......................... 25-28
341-0815 ......................... 25-28
341-0863 ......................... 25-28
341-603 .......................... 25-28
341-6238 ............................ 24
341-6241 .......................... 7, 24
341-637 .......................... 25-28
341-642 .......................... 25-28
341-645 .......................... 25-28
341-744 .......................... 25-27
341-769 .......................... 25-27
341-776 .......................... 25-27
341-8008 ......................... 25-28
341-8017 ......................... 25-28
341-802 .......................... 25-28
341-8140 ............................ 25
341-8141 ............................ 25
341-8142 ............................ 25
341-8143 ............................ 25
341-8144 ............................ 26
341-8145 ............................ 26
341-8146 ............................ 26
341-8147 ............................ 26
341-8148 ............................ 27
341-8149 ............................ 27
341-8150 ............................ 27
341-8151 ............................ 27
341-8152 ............................ 28
341-8153 ............................ 28
341-8154 ............................ 28
341-8155 ............................ 28
341-8156 ............................ 28
341-8160 ............................ 26
341-8161 ............................ 26
341-8162 ............................ 26
341-8163 ............................ 25
341-8164 ............................ 25
341-8165 ............................ 25
341-8166 ............................ 27
341-8167 ............................ 27
341-8168 ............................ 27
341-8169 ............................ 28
341-8170 ............................ 28
341-8171 ............................ 28
356-310 .............................. 7
362-011 ...................... 4, 9, 11, 12
362-0121 .......................... 9, 11
362-015 ......................... 5, 9, 11
362-019 ........................... 9, 11
364-001 ............................. 13
774-012 .............................. 4
A101-101 ............................ 11
A101-104 ............................ 12
A101-105 ............................. 9
A101-108 ............................. 9
FLX15/10 09/05 6-31
Page 32
A101-110 ............................. 4
A101-112 ............................. 4
A101-120 ............................ 13
A101-122 ............................ 13
A101-123 ............................ 13
A101-124 ............................ 13
A101-125 ............................ 12
A101-126 ............................. 9
A101-127 ............................. 9
A101-128 ............................ 19
A101-129 ............................ 19
A101-130 ............................ 11
A101-131 ............................ 11
A101-132 ............................ 11
A101-133 ............................ 11
A101-135 ............................ 11
A101-136 .......................... 9, 11
A101-137 ......................... 11, 17
A101-139 .......................... 9, 11
A101-140 ............................ 19
A101-141 ............................. 9
A101-143 ............................. 9
A101-144 ............................ 12
A101-145 ............................. 4
A101-146 ............................ 12
A101-147 ............................. 9
A101-148 ............................ 19
A101-149 ............................ 11
A101-150 ............................. 7
A101-152 ............................. 7
A101-153 ............................. 7
A101-154 ............................. 7
A101-155 ............................. 7
A101-156 ............................. 7
A101-157 ............................. 7
A101-164 ............................ 11
A101-165 ............................ 11
A101-171 ............................. 4
A101-350 ............................ 21
A101-361 ............................. 9
A101-362 ............................. 9
A101-363 ............................. 9
A101-364 ............................. 4
A102-101 ............................ 11
A102-128 ............................ 19
A102-129 ............................ 19
A102-350 ............................ 22
C000-132 ............................. 4
C000-202 ............................. 6
C000-300 ............................. 6
C000-301 ............................. 6
C000-302 ............................. 6
C000-303 ............................. 6
C000-304 ............................. 6
C000-305 ............................. 6
C000-360 ............................. 5
C000-362 ............................. 5
C000-363 ............................. 5
C502-107 ............................. 4
CS01-134 ............................. 4
PARTS .......................... 1, 2, 30
S000-010 ....................... 4, 11, 16
S000-046 ............................ 17
S000-072 ............................ 17
S000-073 ......................... 11, 17
SERIAL............................... 2
FLX15/10 09/05 6-32
Page 33
A101TG010P
Printed in Canada
Loading...