Tiger Electronics PRS2-V User Manual

Download

Tiger Lily Products TLP, Blinder, Bel, Escort, Valentine

PO Box 549 Tel 303-678-9101 Cel: 720-635-3931 Niwot, CO, USA 80544 Fax 303-678-9103 Cel: 720-298-0557

Email F.John.Turner@TigerLilyProducts.com

WEB www.1stRadarDetectors.com

High Performance

Radar, Laser & Photo

Countermeasures

PRS1-V-360, PRS2-V, PRS3-V, PRS4-V Installation Instructions, 2 Parts

Part 1 of 2: Blinder™ M25 (Dual) & M45 (Quad) Laser Jammer Installation Instructions

We recommend the customer hire a qualified technician to install the Blinder M25 and M45 Laser Jammer.

INSTALLATION: The Blinder™ M25 should be mounted on the front of the vehicle, centered between the license plate and center of

each headlight The M45 adds two additional modules, permitting3 laser modules in front and 1 rear, or 2 in front and 2 rear on either side of the rear license plate. Do not look directly/indirectly into the lens of the Blinder™ at close range, as it emits a bright beam of light

invisible to the human eye and will cause eye damage with prolonged exposure. Install the Blinders level and horizontal with the level device provided in the kit. A block diagram for the M25 and M45 installation areshown below.

MOUNTING:

1) Locate the ideal horizontal location for the Blinder Module (see drawing below for 2/3/4 install in front). Locate the modules

behind the grille for best, hidden view, but do not allow any physical object in front of the lens.

2) Make surethe vehicle is parked on a levelsurface. Install the laser modules level and pointing straight out from the vehicle. If the

grille is rounded, ensure the laser modules are pointing straight out and level. See Diagram left.

3) Use provided hardware to fix the Blinder into position. Recheck the level of each laser module before and after tightening to

position, using the yellow LEVEL device provided. Remove level device after correct install, snap the inserts provided into the level hole of each laser module to achieve a clean, smooth look on each module.

4) Each of the Blinder Jammermodules is connectedto the single interface via telephoneplug in jacks. Theinstallerwillneedto find

a suitable thru hole in the firewallto route the M25 (2) cables or M45 (4) cables through the firewall. Each cable has a firewall grommet, permitting you to replace the present firewall grommet with the Blinder Grommet. You may need to drill a 7/16”

(11mm) diameter hole in the firewall. Use the grommet provided on each cable to seal the firewall.

M25 (2 frontmodules) M45 (3 front modules) M45 (4 front modules)

(1 rear module)

Rated #1, 360 Degree, High Performance, PRS1-STi-360™ Prowler Remote™ System

Got Performance™

Tiger Lily Products TLP, Blinder, Bel, Escort, Valentine

PO Box 549 Tel 303-678-9101 Cel: 720-635-3931 Niwot, CO, USA 80544 Fax 303-678-9103 Cel: 720-298-0557

Email F.John.Turner@TigerLilyProducts.com

WEB www.1stRadarDetectors.com

High Performance

Radar, Laser & Photo

Countermeasures

5) Ensure cables are routed with existing cable bundles and tie wrap the Blinder cables in position. Ensure no contact across hot

surfaces. Connect red lead, to a spare 12Vdc connection in Ignition fuse box. Connect Fuse and Master Power On/off as shown using hardware provided in box. Connect ground black lead of interface module to vehicle ground inside the cab.

6) The BlueWire is a radio mute wire and should only be installed by a professional installer or you could damage your radio.

7) Plug Buzzer and LED Alert into appropriate Alert phone plug of the interface module and connect the Buzzer/LED at a location

that suits your driving habits (perhaps above the windshield visor, or in the dash, or in the center console).

8) Once proper install& electricalhookup is completed, turn Blinder power on. The Blinder™ willgo throughselftest,&beeponce

for 1 second to indicate it is in test mode, and beep a 2ndtimeafter about60 seconds. Duringthe 1stand 2ndbeep, you can use your TV Remote to test the laser modules by aiming the TV Remote at the detector of the module (may be on left or right side of each laser module, depending how installed) and select channel up or down. This can only be done during the 1st15- 60 seconds, at

whichtime the 2ndbeep occurs, the Blinder goes into normalsearch and jam, active mode. The LED will be green with power on, and when jamming, will turn red. Turn Blinder power off, then on again, if more time to self test is required.

CUSTOMER MAINTENANCE: The Blinder™ M25 & M45 lensshould be cleaned witha clean, soft cotton fabric as often as required to remove dust, mud, etc. Do not scratch the lens in your effort to clean it. Performance is degraded if the lens is muddyor covered by

heavy dust. Rock damage, dust and mud can decrease performance.

OPERATION: Whenthe Blinder™ M25 & M45 is turnedon, it will go through a self testcycle (see#8 above) and beep once for about 2 seconds to let the driver know it is fully functional and in active mode of operation. When the Blinder™ detects laser, it immediately

analyzesthe laser gun signal and jams it before the laser gun can display your speed. The Blinder provides anaudio alert to the buzzer and the LED changes from green to red. When alerted, the driver should safely check their speed over a period of 2-3 seconds, then shut

jamming power off after your speed has been safely adjusted. Thisallows the laser gun to detect your speed after you have adjusted your speed. After driving through the laser trap, turn the Blinder™ back on, continue yourjourney safely. Drive alert! Drivesmart! Drivesafe!

DISCLAIMER: Thecustomer is 100% responsible for his/her drivinghabits under any/all situations whenusing the Blinder™. Damage to property orperson due to negligence of any person(s) using the Blinder™ is not the responsibility of Tiger Lily Products or its certified

Distributors. Tiger Lily Products, nor any of its Distributors condone speeding or unsafe driving.

Warranty: TheBlinder™ M25 Dual & M45 Quad Laser Jammer is warranted against defects in material/workmanship for 12 months

from purchase date, but does not include road damage caused by rock damage, improper install, incorrect wiring, misuse, wear, etc.

Plug and Play Cables included in both products

Got Performance™

Rated #1, 360 Degree, High Performance, PRS1-STi-360™ Prowler Remote™ System

Tiger Lily Products TLP, Blinder, Bel, Escort, Valentine

Countermeasures

PO Box 549 Tel 303-678-9101 Cel: 720-635-3931 Niwot, CO, USA 80544 Fax 303-678-9103 Cel: 720-298-0557

Email F.John.Turner@TigerLilyProducts.com WWW.1-Radar-Laser-Jammers-Detectors.com

Best-in-Test

Radar, Laser & Photo

Part 2 of 2:V1 Install Instructions, V1 & Valentine 1 Programming, November 2007

Call us at 303-678-9101 if you want help in changing your Valentine 1 modes of operation.

1. Use J Hooks hardware to install Remote Kit behind grille of vehicle, on top of Ski Rack, or just under the bumper, or in the bumper (if a fiberglass bumper is available). The higherthe better the performance. Drill

holes on the outer flanges of the aluminum enclosure, left and right sides, use J Hooks to hold package to desired surface. A bracket is provided.

2. Ifyour vehicle is an SUVor pickup truck orlarger,youcan install under thebumper. If the install locationis good (typically just under the height of thebumper and approximately 18” back), the V1 will detect radar to the front with excellent sensitivity and to the rear with reasonable sensitivity. Do not install too low due to

potential road damage to the V1 Remote, when parking or going over parking lot bumps.

3. The cable protruding from the Remote Kit is the rear of the kit facing the engine compartment.

4. Ifinstalled behind thegrille, rear radar detection will be significantlyreduced. Ensure no metalis infront of the V1 Remote, and ensure V1 Remote is kept away from radiator to prevent heat damage. If installed inside a front, foam core bumper, ensure no metal is in front of the V1 Remote.

5. Run the 14 foot cable into the cockpit and hook up according to electrical layout highlighted below. If the cabling is ran differently than shown above, there will be no display on the Remote Concealed Display.

6. Call TLP on anyquestions you have or to order remote electronic display,audio control and cabling. The Valentine One inside is a die-cast Magnesium enclosure, surrounded by a very sturdy Aluminum outer enclosure.

Rated #1, 360 Degree, High Performance, PRS1-V™ Prowler Remote™ System

Got Performance™

Tiger Lily Products TLP, Blinder, Bel, Escort, Valentine

Countermeasures

PO Box 549 Tel 303-678-9101 Cel: 720-635-3931 Niwot, CO, USA 80544 Fax 303-678-9103 Cel: 720-298-0557

Email F.John.Turner@TigerLilyProducts.com WWW.1-Radar-Laser-Jammers-Detectors.com

Best-in-Test

Radar, Laser & Photo

How To Change V1Remote and Valentine One Programming.

Call us at 303-678-9101 if you want help in changing your V1 modes of operation. Change Modes at your own risk!

I. How to enter the Programming Mode.

 Starting with the Control Knob in the "off" position, Press and hold-inKnob and at the same time turn the Knob “on;”

continue holding in the Knob until all front-panel lights are on (takes about 5 seconds).

 Release the Control Knob.

II. How to determine your software version.

 Press and immediately release the Control Knob(shown at right) to display software version. The

software-version number is four digits that display one digit at a time in the Bogey Counter-example:

2.869.

 Note your software number, then see the tables on the following pages on features programmable in your unit.  Press and immediately release the Control Knob to exit software-version display and go to Step 1 programming.

III. How to program your desired features.

 The feature character is indicated in the "Bogey Counter" (1, 2, 3, 4, 5, 6, 7, 8, A, b, C, d, E, F, G, H, J, or u).  To select the next Feature Character in the sequence, press and immediately release the Control Knob.

 The Feature State is indicated by direction arrows on the Radar Locator. The Feature State is changed by pressing and

holding the Control Knob until the arrow switches to the opposite direction (takes about 3 seconds). NOTE: If you need to return to an earlier Character in the sequence above, we recommend you switch off the power momentarily, then restart at step I above.The numerical program modes of interest are as follows:

 US/Canadian/HK Frequency: #1 (X band ON = OFF = ) Don’t change any other mode on US/Canada!

 EUROPE / AU Frequency #1 (X band OFF = )

 EUROPE / AU Frequency #2 (K = 24.125GHz : ON = )

 EUROPE / AU Frequency #3 (Ka band ON = )

 EUROPE / AU Band #4 (Laser ON = )

 EUROPE / AU Frequency #4 #H (Ku ON )

 EUROPE / AU Frequency #J (POP3ON = )

 EUROPE / AU Frequency #U (Euro Ka = 34.2GHz, Narrowband Ka ON = )

Do not change any other mode!

Rated #1, 360 Degree, High Performance, PRS1-V™ Prowler Remote™ System

Got Performance™

Tiger Lily Products TLP, Blinder, Bel, Escort, Valentine

Countermeasures

PO Box 549 Tel 303-678-9101 Cel: 720-635-3931 Niwot, CO, USA 80544 Fax 303-678-9103 Cel: 720-298-0557

Email F.John.Turner@TigerLilyProducts.com WWW.1-Radar-Laser-Jammers-Detectors.com

Best-in-Test

Radar, Laser & Photo

IV. How to exit the Programming Mode.

 Switch power off, or unplug. The changes you programmed will be retained in memory.

V. How to tell if V1 has been changed from factory settings.

 If the unit has been changed, P will appear briefly in the Bogey Counter soon after V1 is switched on

(after the lamps-on test, but before the Mode indicator appears.)

 On V1s with serial numbers ending in 0600 or higher, a flashing red LED just to the right of the Bogey

Counter during the sequence above indicates that Ku coverage has been activated.

Rated #1, 360 Degree, High Performance, PRS1-V™ Prowler Remote™ System

Got Performance™

Tiger Lily Products TLP, Blinder, Bel, Escort, Valentine

Countermeasures

PO Box 549 Tel 303-678-9101 Cel: 720-635-3931 Niwot, CO, USA 80544 Fax 303-678-9103 Cel: 720-298-0557

Email F.John.Turner@TigerLilyProducts.com WWW.1-Radar-Laser-Jammers-Detectors.com

Best-in-Test

Radar, Laser & Photo

Euro K band is at 24.125GHz. Wideband Ka is turned off when Euro Ka is turned on. Ku is used in UK,

Netherlands, Northern France, Taiwan, Belgium, but not in the USA as of Jan07.

The Euro Mode and Ku band are separate features and require separate activation. Euro Mode is a narrowband Ka used in Europe and Australia on photo speed traps.

When Euro Mode has been activated, upon power up you will see the sequence "E," "u," "r" appear in the Bogey Counter. When the power-up sequence is complete, the Bogey

Counter will show either "U" or "u." Pressing the Control Knob will toggle between them.

Select "U" to enable both K and narrowband Ka (Photo) bands. Select "u" to enable only narrow Ka band.

Euro Ka(Big U) mode detects:

Ka POPIII 33.8GHz KA Narrowband 33.97GHz to 34.65GHz after July 2006 (Rev 3.8.5.1 and later

KA Narrowband 34.2GHz to 34.45GHz before July 2006 K 24.125GHz and K POPIII radar

X turned off

Euro Ka(little u) mode detects:

Ka POP 33.8GHz KA Narrowband 33.97GHz to 34.65GHz

after July 2006 (Rev 3.8.5.1 and later KA Narrowband 34.2GHz to 34.45GHz before July 2006

All K turned off All X turned off

Euro Ku: 13.45 GHz

Rated #1, 360 Degree, High Performance, PRS1-V™ Prowler Remote™ System

Got Performance™

Tiger Electronics PRS2-V User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual