P A RTS LISTING WITH
MOUNTING AND OPERATING
INSTRUCTIONS
Tiger Corporation
3301 N. Louise Ave.
Sioux Falls, SD 57107
1-800-843-6849
1-605-336-7900
www.tiger-mowers.com
06011008
TO THE OWNER / OPERATOR / DEALER
All implements with moving parts are potentially hazardous. There is no substitute for a cautious,
safe-minded operator who recognizes the potential hazards and follows reasonable safety practices.
The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!! Read the safety messages on the implement and shown in this manual.
Observe the rules of safety and use common sense!
READ AND UNDERSTAND THIS MANUAL! Non–English speaking operators will need to GET
THE MANUAL TRANSLATED as needed!
W arranty Information: Read and understand the complete W arranty Statement found in this manual. Fill out the
W arranty Registration form in full and return it within 90 days. Make certain the Serial Number of the machine is
recorded on the W arranty Card, and form that you retain.
FORWARD
This manual contains information about many features of the T iger mowing
and roadside maintenance equipment. Some of these include: Safety precautions,
Assembly instructions, Operations, Maintenance and Parts. This manual will also
assist you in the proper break-in, daily care, andtroubleshooting of your new
mower .
We recommend that you read carefully the entire manual before operating the
unit. Also, time spent in becoming fully acquainted with its performance features,
adjustments, and maintenance schedules will be repaid in a long and satisfactory
life of the equipment.
T roubleshooting - Please, before you call, help us to help you!
Please look at the equipment to observe what is happening, then:
• Classify the problem
• Hydraulic, electrical or mechanical - Read the trouble shooting section
• Tractor or T ruck chassis - Contact vehicle dealer
• If unable to correct the problem yourself, contact your localTiger Dealer af ter
gathering:
• Machine model _______________________
• Serial number ________________________
• Dealer name _________________________
• Detailed information about the problem including results of troubleshooting
Attention Owner / Operator / Dealer: It is your obligation to read, and understand,
the warranty information section located at the back of this manual denoting that the
purchaser understands the safety issues relating to this machine and has received
and will read a copy of this manual.
If at any time, you have a service problem with your Tiger mower , Contact
your local dealer for service and parts needed.
MANUF ACTURED BY:DISTRIBUTED BY :
Tiger Corporation_____________________
3301 N. Louise Ave._____________________
Sioux Falls, SD 571071-_____-_____-________
1-800-843-68491-_____-_____-________
1-605-336-7900
www .tiger-mowers.com
A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to
the owner/operator . Most accidents can be avoided by being aware of your equipment, your surroundings, and
observing certain precautions. The first section of this manual includes a list of Safety Messages that, if
followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety
Messages before assembling, operating or servicing this Implement. This equipment should only be operated
by those persons who have read the manual, who are responsible and trained, and who know how to do so
responsibly.
The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this
manual and on decals which are attached to the equipment. The Safety Alert Symbol means:
“ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word
are intended to warn the owner/operator of impending hazards and the degree of possible injury
faced when operating this equipment.
Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR
VERY SERIOUS INJURY.
Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH
OR SERIOUS INJURY.
Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR
INJURY.
Identifies special instructions or procedures that, if not strictly observed, could result in
damage to, or destruction of the machine, attachments or the environment.
NOTE: Identifies points of particular interest for more efficient and convenient operation or repair.
(SG-1)
Practice all usual and customary safe working precautions and above all---remember safety is
up to YOU
. Only YOU can prevent serious injury or death from unsafe practices.
READ, UNDERSTA ND, and FOLLOW the following Safety Messages. Serious injury or
death may occur unless care is taken to follow the warnings and instructions stated in the
Safety Messages. Always use good common sense to avoid hazards.
Repeated or substantial breathing of hazardous dusts, including
crystalline silica, could cause fatal or serious respiratory disease including
silicosis. Concrete, masonry, many types of rock, and various other
materials contain silica sand. California lists respirable crystalline silica as
a substance known to cause cancer. Operation of this equipment under
certain conditions may generate airborne dust particles that could contain
crystalline silica. In those conditions, personal protective equipment
including an appropriate respirator must be used. If excessive dust is
generated, a dust collection or suppression system should also be used
during operation.
(SG-41)
Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las
medidas de seguridad.
(SG-3)
Never operate the Snow Plow until you have read and completely
understand this Manual, the Truck or Power units Operator’s
Manual, and each of the Safety Messages found in these Manuals
and those affixed to the Snow Plow, Truck, or Power units and its
components. Learn how to stop the power unit engine suddenly in
an emergency
.
Never allow inexperienced or untrained personnel
to operate the Truck or Power unit and Snow Plow without
supervision. Make sure the operator has fully read and understood
the manuals prior to operation.
(SPNG-4)
In addition to the design and configuration of this Snow Plow, includ ing Safety Signs and Safety Equip ment,
hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper
training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer
also to Safety Messages and operation instru ction in each of the appropriate sections of the Truck or Power
unit Manuals. Pay close attention to the Safety Signs affixed to the Snow Plow.
(SNPG-5)
PA RT S I N F O R M AT I O N
HENKE Snow Plows use balanced and matched system components for plows, carriers, and other
components. These parts are made and tested to HENKE specifications. Non-genuine or “will fit" parts do
not consistently meet these specifications. The use of non-genuine or “will fit” parts may reduce Snow Plow
performance, void HENKE warranties, and present a safety hazard. Use genuine HENKE parts for economy
and safety.
(SNPG-6)
SEE YOUR HENKE DEALER
Always maintain the safety signs in good readable condition. If th e safety signs are missing,
damaged, or unreadable, obtain and install replacement safety signs immediately.
All Safety Shields, Guards and other Protective Safety devices should be used and
maintained in good working condition. All safety devices should be inspected
carefully at least daily for missing or broken components.
NEVER REMOVE
PROTECTIVE SHIELDS AND GUARDS! NEVER MODIFY OR CUT PROTECTIVE SHIELDS OR
GUARDS!
When shields or guards are removed to access areas for maintenance, they must be
replaced and be in good condition before operating. Missing, broken, or worn shields,
guards, and other protective devices must be replaced at once and prior to operation
to reduce the possibility of injury.
(SNPS-02)
The Snow Plow power unit should be equipped with a fire extinguisher, rated for all fires, in
an accessible and visible area. The fire extinguisher should be inspected routinely by a
certified inspector for operational use and replaced as needed. Never obstruct access to
the fire extinguisher.
(SNPS-6)
NEVER use drugs or alcohol immediately before or while driving or operating the Snow
Plow. Drugs and alcohol will affect an operator’s alertness and coordination and therefore
affect the operator’s ability to operate the Equipment safely. Before operating the
Equipment, an operator on prescription or over-the-counter medication must
consult a medical professional regarding any side effects of the medication
that would hinder their ability to operate the Equipment safely. NEVER
knowingly allow anyone to operate this Equipment when their alertness or
coordination is impaired. Serious injury or death to the operator or others
could result if the operator is under the influence of drugs or alcohol.
(SNPD-3)
Always wear OSHA approved Personal Protective Equipment (PPE) while operating,
servicing, repairing, and/or cleaning the Equipment. PPE is designed to provide bodily
protection during such activities.
Personal Protective Equipment includes:
-Protective Eye Wear
-Steel Toed Safety Footwear
-Gloves
-Hearing Protection
-Close Fitted Clothing
-Hard Hat-When working around a raised hopper.
-Respirator-Depending on conditions and material bein g swept or cleaned.
Specialized protective equipment may be required if dangerous or hazardous material is being moved by the
Prolonged operation of the Snow Plow may cause operator boredom and/or fatigue
affecting the safe operation of the Snow Plow and Truck or Power unit. It is recommended
that the operator take scheduled work breaks to help prevent these potentially impaired
operating conditions. If possible, completely shut down the Equipment, exit the cab and
move around stretching your arms and legs. Never operate the Equipment in a fatigued or
bored mental state that impair s proper and safe Equipment operation.
(SNPD-5)
PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE
PERMANENT HEARING LOSS!
Equipment operation can often
be noisy enough to cause permanent hearing loss. We
recommend that you always wear hearing protection if the noise in
the Operator’s position exceeds 80db. Noise over 85db over an
extended period of time will cause severe hearing loss. Noise
over 90db adjacent to the Operator over an extended period of
time will cause permanent or total hearing loss.
Note:
Hearing
loss from loud noise [from sweepers, chain saws, radios, and
other such sources close to the ear] is cumulative over a lifetime
without hope of natural recovery.
(SNPD-6)
Prolonged operation of the Equipment in cold weather may cause operator hypothermia
affecting the safe operation of the Snow Plow and Truck or Power unit. It is recommended
that the operator wear appropriate clothing take scheduled work breaks to help prevent
these potentially impaired operating conditions. If possible, completely shut down the
Equipment, exit the cab and warm the body in a properly heated area. Never operate the
Equipment in a fatigued or impaired mental state that effects the proper and safe
Equipment operation.
(SNPD-8)
Use both hands for support when getting on and off the truck or power unit. Use handles
and steps on the equipment for support wh en boarding. Never use the Truck or Snow Plow
control levers for support when boarding the equipment.
(SNPO-01)
Use available truck or power unit handles and steps to exit the operator’s station. Make
sure you have solid footing before stepping down. Be careful of your step and use extra
caution when mud, ice, snow, or other matter has accumulated on the steps or handrails.
Never rush to exit or jump off the truck or power unit.
(SNPO-02)
Do not attempt to mount the Truck or Power Unit while the machine is moving.
Never attempt to mount a runaway Snow Plow. Serious injury or death may
occur from being run over by a moving Truck, Power Unit, or Snow Plow.
(SNPO-03)
BEFORE leaving the operator’s seat, always engage the parking brake and/or set the
Truck’s or Power Unit’s transmission in the park position, stop the engine, remove the key ,
and wait for all moving parts to stop. Never dismoun t a Truck or Power Unit that is moving
or while the engines are running. Operate the equipment controls from the Operator’s
seat only.
Always wear a seat belt while driving the equipment during operation and transport.
Serious injury or even death could result from falling from the operator’s station or from
being involved in a collision.
(SNPO-05)
Start the engines only when seated and belted in the operator’s seat. Operate the
equipment controls only while properly seated with the seat belt secured around you.
Inadvertent movement of the power unit or attachment components may cause serious
injury or death to the operator and passersby. Read the truck or Power Unit operator’s
manuals for proper starting instructions.
(SNPO-06)
Do not operate, or perform maintenance to, the Equipment while wearing loose fitting
clothing. Entanglement of loose clothing with the rotating elements can result in serious
injury or death. Stay clear of all rotating elements at all times.
(SNPD-7)
Operate only in conditions where you have clear visibility of the area in daylight or with
adequate artificial lighting. Never operate in darkness of foggy conditions where you
cannot clearly see at least 50 feet in front and to the sides of the equipment. Make sure
that you can clearly see and identify passersby, steep slopes, ditches, drop-offs, overhead
obstructions, power lines, oversized debris and foreign objects. If you are unable to see
these types of items, discontinue operation until visibility improves.
(SNPO-8)
When transporting the Snow Plow between locations, follow all local traffic laws and
regulations.
(SNPO-10)
Operate at a speed that allows you to safely opera te and con trol the Truck and Snow Plow.
Safe plowing speed depends on street condition and the type and amount of debris being
moved. Slow down for corners, curbs, parked cars, protruding signs and other obst acles.
Use slow traveling speeds when operating on or near steep slopes, ditches, drop-offs,
overhead obstructions, power lines, or when debris and foreign objects are to be avoided.
(SNPO-13)
Do not operate the Equipment if excessive vibration or noise exists. Shut
down the equipment and the Truck or Power Unit engine. Inspect the
Equipment to determine the source of the vibration or noise. If parts are
loose, damaged, or missing, replace them immediately. Do not operate the
Equipment until all necessary repairs have been performed. To reduce the
possibility of property damage, serious injury, or even death, never operate
the Equipment with missing or damaged components.
(SNPO-16)
Never attempt to plow debris that is too large for the Snow Plow (oversized objects such as
broken limbs and discarded tires). Such objects may damage the snow plow components
and cause serious mechanical damage to the equipment. If possible, carefully place such
objects out of the Snow Plow and traffic path until properly removed by another means.
Unplowed snow, piled ice and debris, and snow drifts left behind the equip ment m i ght p ose
a driving hazard to vehicle traffic colliding with the debris or losing traction on the material.
It is recommended to post warning signs alerting driver’s of the equipment operation
presence and the need to reduce vehicle speed. If such hazards are left behind following
the Snow Plows passage, the area should be plowed a second time an d any remaining
hazards removed by an alternative method.
(SNPO-19)
Use extreme caution when lowering the Snow Wing. Make sure no bystanders are close
by or underneath the wing while lowering. Allow ample clearance around the equipment
when lowering or raising the wing. Use extreme caution around obstructions including
bystanders, passersby, curbs, buildings, and other property. Use the Truck’s or Power
Unit’s horn to warn of danger when the wing is being lowered. Lower wing slowly and
carefully. Sudden or unexpected dropping of wing could result in serious injury.
(SNPO-24)
Do not allow the Snow Plow to come in contact with potentially dangerous and/or
hazardous material. Such hazards may include, but are not exclusively limited to, the
following:
•Fire Hazards- Fuel spills, burning material,
•Chemical Hazards- Chemical spills, discarded chemical containers, batteries,
•Corrosive Materials-Batteries, Acids and Bases.
In most areas, these types of material require special handling requirements for safe and proper disposal and
should not be plowed by the Snow Plow, nor can they be disposed of in a general landfill site like most swept
waste. Contact the appropriate authority for th e colle ction and dispo s al requ ire ments of such dangerous and/
or hazardous material.
(SNPO-25)
Always wear required OSHA approved Personal Protective Equipment (PPE) when coming
in contact with and removing potentially dangerous and hazardous material that has
collected on the Snow Plow equipment or which is obstructing one or more components.
Pay close attention to dangerous and hazardous material including, but not exclusively
limited to, chemicals, decaying carcasses and sharp objects.
(SNPO-26)
Verbal communication near a Truck or Power Unit and Snow Plow is difficult and
dangerous. Operating instructions and directions should be made prior to starting the
equipment. Unclear and misunderstood communication may lead to operator and
bystander injury or death and equipment damage. If communication by the operator is
necessary, completely shutdown and exit the equipment. Never allow anyone to approach
the equipment while in operation.
(SNPO-28)
Never allow children to play on, under, or around the Truck or Power Unit nor allow children
to operate equipment controls. Children can slip or fall off the equipment and be injured or
killed. Children can cause the equipment components to shift or fall crushing themselves
or others.
Allow passengers only in situations where their presence is involved in the operation
(operator training, supervision, maintenance inspection). Never carry passengers whose
presence distracts from the safe operation or transport of the equipment. Passengers
must be seated securely and belted in the cab’s passenger seat. Never allow any person
to ride on any other location of the Truck, Power Unit or Snow Plow during operation or
transport.
(SNPO-30)
Extreme caution should be used by the operator when operating near passersby. Stop
snow plowing if a passerby comes within 25 feet of the plow to prevent possible passerby
injury or death from being struck by the equipment or from a thrown object.
(SNPO-31)
Under certain conditions, the Snow Plow is capable of propelling objects up to 75 feet. Be
extremely careful when plowing at higher speeds and hitting large dense objects, such as
rocks, chucks of frozen ice, metal objects, broken glass, or other solid objects that might
become propelled and cause bodily injury to passersby or damage to property such as
windows and vehicles.
(SNPO-32)
Make sure that no bystander, animal or obstruction such as a vehicle, building, or
street sign are within the width of the Snow Plow. The design of the Snow Plow may
impair the operator vision when operating. Use extreme caution to ensure that the
Snow Plow is not driven into the path of pedestrian or vehicle traffic. Serious injury
or death and property damage could result from running into, being crushed by, or
run over by a Snow Plow.
(SNPO-33)
Make sure no bystanders or animals are within 25 feet of the equipment
basket when dumping contents from or cleaning the Snow Basket. Bucket
contents, which may exceed several thousand pounds, could fall and crush a
bystander or an animal resulting in possible injury or death.
(SNPO-34)
On fully assembled unit, do not remove the wing retaining chain until hoses
are attached to the power unit and the wing folding cylinders have been filled
with oil. Lower wings slowly and carefully. Keep bystanders clear of area
when lowering wings. Sudden or unexpected dropping of wing could result in
serious injury.
(SNPO-36)
Use extreme caution when operating the Equipment in traffic. To alert motorist of the
Equipment’s presence, use all equipped warning signals to alert motorist and pedestrians
of the equipment’s presence and relatively slow speed. Serious injury or death and
property damage may occur if a vehicle collides with this Equipment.
(SNPS-3)
Before starting a snow plowing operation, make sure all the warning signal lights are
connected, visible and working. Routinely inspect the equipment’s headlights, brake lights,
backup lights, and turn signal lights for operational condition. Immediately repair nonfunctioning lighting. Always follow all local traffic regulations while operating the Snow
Plow.
Always turn on all safety lights and flashers when you operate the Snow Plow. (SNPS-5)
Be particularly careful in transport. The Implement has raised and moved the center of
gravity to the front of the Power Unit increasing the possibility of overturn and tipping
forward. Turn curves or go up slope s o nly at lo w sp eed and using a g radua l tur ning angle.
Go up slopes with the Implement located uphill. Slow down on rough or uneven surfaces.
(SPU-2)
Do not stand or allow bystander or coworkers between the attachment
and the truck or power unit while installing or disconnecting the
attachment. Keep hands and body clear of the attachment and the
attachment mounts. Serious injury or death can result from a person
being crushed between the attachment and truck or po wer unit.
(SNPC-01)
Reset the tripped snow plow edge by raising the snow plow off the ground. DO NOT
attempt to reset the trip edge by hand. The trip edge is spring loaded and sudden and
unexpected movement can occur resulting in serious injuries. Keep and hands and feet
away from the trip edge. If the trip edge does not reset, stop plowing and have the snow
plow repaired before resuming snow plowing.
(SNPO-12)
Make sure the implement is properly attached to the Power Unit and the retaining pins
securely lock the Implement into position. Improper mounting of the Implement onto the
Power Unit can result in the Implement falling causing serious injury.
(SNPC-02)
The operator of the equipment must be trained in the operation and safe use of this
machine. The operator must read and completely understand the operator’s manuals of
the Snow Plow, Truck or Power unit manufacturers. New operators should be trained in an
open area clear of obstructions before operating on public roadways. If operation of the
entire Snow Plow unit (Truck or Power unit) is not c ompletely understood, consult your
authorized sales representative for a detailed explanation. Never allow an untrained or
unqualified driver to operate the Snow Plow.
(SNPD-1)
The Snow Plow driver must meet the requirements and possess a Motor Vehicle License
as determined by the state in which the Snow Plow is operated if used on public roadways.
Contact your local State Department of Public Safety office for special licensing
requirements to operate the Snow Plow in your area.
(SNPD-2)
CONNECTING OR DISCONNECTING IMPLEMENT SAFETY
INSTRUCTIONS AND PRACTICES
Perform service, repairs and lubrication according to the maintenance section. Ensure the
unit is properly lubricated as specified in the lubrication schedule and all bolts and nuts are
properly torqued. Failure to properly servic e, repair and maintain this Implement in good
operating condition could cause component failure and possible serious injury or even
death.
(SG-35)
Periodically inspect all moving parts for wear and replace
when necessary with authorized service parts. Look for loose
fasteners, worn or broken parts, and leaky or loose fittings.
Make sure all pins are properly secured. Serious injury may
occur from not maintaining this equipment in good working
order.
(SNPM-01)
I nspect the entire Snow Plow before each use. Accidents may occur or damage to the
equipment may result if the Snow Plow is not maintained in good mechanical working
order.
•Check for loose bolts, worn or broken parts, pinched hydraulic hoses, and leaky or loose fittings.
•Make sure all pins are secure and safety pin equipped.
•Make sure replacement parts are the correct size and properly installed.
•Make sure all fluid levels are full and replenish as necessary.
•Make sure fuel, oil, and coolant caps are replaced and tightened.
•Check tire condition for tread wear and tire pressure at the rated PSI.
•Make sure that all safety shields and guards are attached and in good condition.
•Make sure all scheduled maintenance is up to date.
(SNPM-02)
Do not modify or alter this Snow Plow. Do not permit anyone to modify or
alter this equipment, any of its components or any Snow Plow function.
Modification can result in equipment failure and cause serious injuries to the
operator, coworkers, or bystanders.
(SNPM-03)
Use extreme care when climbin g onto the equipment to perform repairs, maintenance,
and cleaning. Use proper stands and ladders to access areas that cannot be reached from
ground level. Slipping and falling off the equipment can cause serious injury or death.
(SNPM-04)
Never attempt to repair, lubricate, adjust, clean, remove obstructions or perform any other
type of service to any component while the Snow Plow is in motion or while the engine is
running. Completely shut down the engine and wait for all motion to come to a complete
stop before servicing the Snow Plow.
(SNPM-05)
MAINTENANCE AND SERVICE SAFETY INSTRUCTIONS AND
PRACTICES
Never leave the Snow Plow unattended while the plow is in the raised position. Accidental
operation of the lifting lever or a hydraulic failure may cause a sudden drop of the unit
which could result in injury or death by crushing. If the plow must be raised for inspection
or service securely block up and support the Plow to prevent it falling.
(SNPM-06)
Never crawl under the Snow Plow or any raised component unless it is properly blocked
up and support to prevent it from falling. Accidental operation of a lifting lever or hydraulic
failure may cause a sudden drop of the unit with injury or death by crushing.
(SNPM-07)
Use proper protective equipment including gloves, safety eye wear, arm protection when
handling plow blades and components during r eplacement, adjustment, and m aintenance.
Plow edges and components can become sharp and have burrs that could inflict puncture
and cuts to the hands, arms, and/or eyes if proper protective equipment is not worn.
(SNPM-08)
Replace bent, cracked, or broken plow blade with a new blade. Never attempt to
straighten or weld on plow blades because this will likely crack or otherwise damage the
blade with subsequent failure and possible serious injury from broken blade being ejected
from plow.
(SNPM-10)
Escaping pressurized hydraulic oil generated by hydraulic pumps has the potential to
inflict serious injury and possible death. Never attempt to repair a pump or hose or tighten
a connection while the system is pressurized. Always shut down the engine and relieve
hydraulic oil pressure before performing any repairs to the hydraulic system.
(SNPM-11)
Hydraulic pressure must be relieved from the hydraulic circuit prior to doing any
maintenance or repair work and when the Snow Plow is parked at the end of the day.
Place the Snow Plow(s) on the ground or securely blocked up. Turn off the Truck engine
then engage the hydraulic remote cylinders several times to relieve hydraulic pressure
prior to performing any maintenance or repair work.
(SNPM-12)
Never remove debris from or unclog jams in the plow or lifting compon ent s until the engine
have been completely shutdown and all components have come to a complete stop and
are lowered to ground level and hydraulic pressure relieved. Always wear PPE when
removing collected material and debris from the equipment. Serious injury or death may
occur if any of these precautions are not followed when removing plugged or entangled
debris.
(SNPM-15)
Engine Exhaust, some of its constituents, and certain vehicle components contain or emit
chemicals known to the state of California to cause cancer and birth defects or other
reproductive harm.
Do not operate this equipment with hydraulic oil or fuel
leaking. Oil and fuel are expensive and their presence
could present a hazard. Do not check for leaks with your
hand! High-pressure oil streams from breaks in the line
could penetrate the skin and cause tissue damage including
gangrene. To check for a hose leak, SHUT the ENGINE OFF and
remove all hydraulic pressure. Wear oil impenetrable gloves, safety
glasses and use Cardboard to check for evidence of oil leaks. If you
suspect a leak, REMOVE the HOSE and have it tested at a Dealer.
If oil does penetrate the skin, have the injury treated
immediately by a physician knowledgeable and skilled in
this procedure.
(SNPM-21)
Always read carefully and fully comply with the manufacturers instructions when handling
fuels, oils, solvents, cleansers, and any other chemical agent.
(SNPM-22)
Battery posts, terminals and related accessories contain lead and lead compounds,
chemicals known to the state of California to cause cancer and birth defects or other
reproductive harm. Wash Hands after handling
. (SNPM-23)
Avoid contact with hot surfaces on the bottom of the skid shoes or plow cutting
edges. Use gloves and eye protection when servicing hot components. Contact
with a hot surface can cause serious injury from burns or scalding.
(SNPM-24)
Remove the negative battery cable from the batte ry before p erformin g any mainten ance on
the electrical system to prevent an accidental circuit shorting and sparks. Sparks can
result in wiring damaged, fire or personal injury.
(SNPM-25)
DO NOT allow any person under a folded wing unless wing is securely supp orted or locked
up with the safety chain. Never wor k under a lifted component unless the compon ent is
securely supported or blocked up. Keep bystanders clear of area when lowering wings.
Sudden or unexpected dropping of wing could result in serious injury.
(SNPM-26)
Before conducting maintenance on the Snow Plow stop the truck or Power Unit, place the
transmission in the park position a nd set the parking brake. Turn the engine off and
remove the key to prevent inadvertent or accidental starting of the engine. Unexpected
engine start up or vehicle movement can result in serious bodily injuries or death.
Secure the wing for transport when not plowing. Secure wing in transport
position using wing transport safety chain. Sudden or unexpected dropping of
wing could result in serious injury.
(SNPO-35)
Transport the Truck, Power Unit, and Snow Plow only at safe speeds. Serious accidents
and injuries can result from driving this equipment at unsafe speeds. Become familiar with
the driving characteristics of the equipment and how it handles before operating or
transporting on streets and highways. Make sure the Truck’s or Power Unit’s steering,
brakes, and wheels are in good condition and operate properly)
Before transporting the Equipment determine the safe transport speeds for you and the machine.
Make sure you abide by the following rules:
•Test the Truck or power unit and Snow Plow at a slow speed and increase the speed slowly. Apply the
brakes smoothly to determine the stopping characteristics of the Truck equipped with the Snow Plow . As
you increase the speed of the Truck, the stopping distance increases. Determine the maximum safe
transport speed for you and the equipment. When driving down a hill or on wet or icy roads, the braking
distance increases: use extreme care and reduce you r spee d . Do not oper a te th e eq uip m en t with wea k
or faulty brakes.
•Obey all traffic laws and regulations. Never exceed the posted speed limit.
•The Snow Plow has moved the center of gravity of the equipment forward. Use extreme caution when
transporting at highway speeds. Slow down for sharp corners or on slopes to avoid loss of steering control.
•Only transport the equipment at the speeds determined as safe and which allow for proper control of the
machine while driving and stopping during an emergency.
•When operating in traffic, use the Truck’s or Power Units directional indicator or signal lights to indicate
your movement. Always use the flashing warning lights and other equipped warning features to alert
motorist of your presence and slow moving speed when oper ating in traf fic. Be A ware of Traffic Around You and Watch Out for the Other Guy.
This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning
employer and employee equipment operators. This section is not intended as a legal interpretation of the law and
should not be considered as such.
Employer-Employee Operator Regulations
U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA
This Act Seeks:
“...to assure so far as possible every working man and woman in the nation safe and healthful working
conditions and to preserve our human resources...”
DUTIES
Sec. 5 (a) Each employer(1) shall furnish to each of his employees employment and a place of employment which are free from
recognized hazards that are causing or are likely to cause death or serious physical harm to his employees;
(2) shall comply with occupational safety and health standards promulgated under this Act.
(b) Each employee shall comply with occupational safety and health standards and all rules, regulations and
orders issued pursuant to this Act which are applicable to his own actions and conduct.
OSHA Regulations
OSHA regulations state in part: “At the time of initial assignment and at least annually thereafter, the employer
shall instruct every employee in the safe operation and servicing of all equipment with which the employee is,
or will be involved.”
Employer Responsibilities:
To ensure employee safety during plow and truck or other power unit operation, it is the employer’s responsibility to:
1.Train the employee in the proper and safe operation of the plow and truck or other power unit.
2.Require that the employee read and fully understand the plow and truck or other power unit Operator’s manual.
3.Permit only qualified and properly trained employees to operate the plow and truck or other power unit.
4.Maintain the plow and truck or other power unit in a safe operational condition and maintain all shields and guards
on the equipment.
5.Ensure the truck or other power unit is equipped with a functional ROPS and seat belt and requ ire that the
employee operator securely fasten the safety belt and operate with the ROPS in the raised position at all times.
6.Forbid the employee operator to carry additional riders on the Tractor or Implement.
7.Provide the required tools to maintain the plow and truck or other power unit in a good safe working conditio n and
provide the necessary support devices to secure the equipment safely while performing repairs and service.
8.Require that the employee operator stop operating equipment if bystanders or passersby come within 25 feet.
Child Labor Under 16 Y ear s of Age
Some regulations specify that no one under the age of 16 may ope rate power machinery. It is your responsibility to
know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard
Administration, Wage & Home Division, Child Labor Bulletin #102.)
Before attempting to mount or service your Tiger
equipment, it is important to read and understand all of the
information in the Safety section of this manual.
Check complete shipment list against the packing list to make sure there are no
shortages. Make certain the tractor model is the appropriate one for the mower received!
Always use a floor jack, hoist or fork lift to lift and raise heavy parts.
Read and understand the entire assembly section instructions before attempting
to mount your Tiger mower. Refer to the parts section of this manual for detailed
illustrations to locate all parts.
Assembly Section 2-2
ASSEMBLY
MULTIPLIER VALVE CONTROLLER MOUNTING
The Multiplier Valve Controller comes with two worm-screw ties that are used to
attach the Controller to the Tractor Joystick as shown below.
The Multiplier V alve Controller can also be attached to the tractors’ joystick by removing
the joystick handle, drilling two holes, and using the 10-32 machine screws and nylock
nuts which are provided.
MULTIPLIER VALVE CONTROLLER WIRING
The red wire coming out of the bottom of the controller should be routed inside the
tractor cab and inserted into the Tractor Auxillary Plug-in. The cable wires should be
routed through the rear window of the tractor cab to the Multiplier V alve.
Black wire: Top button on controller.
White wire: 2nd button on controller.
Orange wire: 3rd button on controller.
Green wire: 4th button on controller.
Black wire
Assembly Section 2-3
ASSEMBLY
HYDRAULIC MULTIPLIER VALVE MOUNTING
Align the mounting bracket to the existing holes on rear of the tractor by the PTO.
Secure the bracket to the tractor with the existing hardware. Then align the holes and
secure the valve to the mounting bracket as shown in the parts section. Install the
electrial control wires from the controller that are routed through the rear window of the
cab. See previous page for wire designation. Install the hydraulic lines from the Multiplier
V alve to the tractor remotes.
PRESSURE FROM
REMOTE
RETURN FROM
REMOTE
MOUNTING BRACKET
FOUR FUNCTION
HYDRAULIC
MULTIPLIER V AL VE
EXISTING HARDWARE
Assembly Section 2-4
ASSEMBLY
HYDRAULIC SYSTEM DIAGRAM
Assembly Section 2-5
ASSEMBLY
3-POINT PUSH ARM STOP MOUNTING
Install the Push Arm Stop onto the 3-point hitch using the pins as shown in the
parts illustration. Adjust the bottom arms so the Push Arm Stop is 17” to the ground
at the Pivot Boss. Adjust the top link so that the Push Arm Stop is approximately level
with the ground.
ADJUSTING REAR WHEELS
Follow the instructions in the tractor owners manual for adjusting tires and
rims. The rear wheels MUST be adjusted to the widest setting. NOTE: This may
require switching the wheels to opposite sides of the tractor. Also take note of any width
restrictions when transporting by trailer. (For ease of inst allation, it is best to leave rear
wheels removed during installation of the mower).
Assembly Section 2-6
ASSEMBLY
WELDING MAIN FRAME
Make sure you use the appropriate safety equipment. Weld the Tangs onto your
existing Main Frame as shown below. Next, weld on the Boss’ making sure the
orientation of the cross holes for the bolts are correct.
ITEMPART NO.QT YDESCRIPTION
106300059*MAIN FRAME
2064010662TANG ,LEFT,MNFRM
3064010671T ANG,RIGHT ,MNFRM
4064700131BOSS,2.50OD x 1.56ID x 1.00
523387A2BOSS,2.50OD x 1.53ID x 1.25
Assembly Section 2-7
ASSEMBLY
FINAL PREPARATION FOR OPERATION
Place operators safety and operation decals on the steering column and side counsel
where they are clearly visible to the operator. These decals should be understood by
each operator of the machine in conjunction with the safety and operation section of this
book. The decals are to be maintaned in good condition as a reminder to the operator ,
and should be replaced if damaged.
Finally , all bosses, pins and pivot points will need to be greased as instructed in the
maintenance section of this manual. The hydraulic reservoir can also be filled with the
recommended fluid (see maintenance section) and the filter installed in the top of the
tank. Double check all fittings and fasteners BEFORE starting tractor. Also secure
any loose hoses together with zip ties and wrap with split hoses where friction may
occur on the hoses.
BEFORE starting or operating the tractor you must read and understand
the safety and operation sections of this manual completely.
BE SURE THE BALL V ALVES ARE OPEN! S tart tractor and allow instrument s to
stabilize. Using a piece of paper or cardboard as noted in the safety and maintenance
sections, check all fittings and connections for hydraulic leaks.
If a leak is found, you must shut down the tractor, set the cutter on the ground.
Before attempting to fix the leak, you must actuate the lift valve handles several times to
relieve any pressure in the lines.
Before operating the plows, the front and side plows should be slowly moved
throughout the full range of motion. Watch for any condition that would cause pinching
or excess stress on the hoses. The steering and front axle travel should also be
carefully moved through their full range of motion. If any condition occurs in which the
hoses contact the tires, the steering and / or front axle travel may need to be limited as
described in the tractor operators manual. This should also be done if the tires rub, or
are extremely close to any other part of the plow. This may include adding shims, or
adjusting stop bolts in the tractor front to solve the problem. While checking motion,
you should also check that the control circuits are connected according to the operators
decal for the valve handles.
Assembly Section 2-8
OPERATION
OPERATION
SECTION
Snow Plow Operation Section 3-1
OPERATION
Safety is of primary importance to the owner / operator and to the manufacturer.
The first section of this manual includes a list of Safety Messages, that, if followed,
will help protect the operator and bystanders from injury or death. Many of the
messages will be repeated throughout the manual. The owner / operator / dealer
should know these Safety Messages before assembly and be aware of the hazards
of operating this mower during assembly, use, and maintenance.
The Safety Alert Symbol combined with a signal word, as seen below, is
intended to warn the owner / operator of impending hazards and the degree of injury
possible during operation.
Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH
OR VERY SERIOUS INJURY.
Indicates an imminently hazardous situation that, if not avoided, COULD result in
DEA TH OR SERIOUS INJURY.
Indicates an imminently hazardous situation that, if not avoided, MA Y result in MINOR
INJURY.
IMPORTANT!
Identifies special instructions or procedures that, if not strictly observed, could result
in damage to, or destruction of the machine, attachments or the enviroment.
NOTE:Identifies points of particular interest for more efficient or convienient operation or
repair. (SG-1)
Before any operation of tractor and equipment, the user should read
andunderstand the safety and operating instructions for both the tractor and
the equipment. The user should also be familiar with the location and
functions of the units instruments and controls. Being familiar with the
machine and it’s controls will increase efficiency and reduce possibility of
serious injury or damage to the unit. The operator should work slowly and carefully
until he feels comfortable with the machine. S peed and skill will be attained much
easier if the necessary time is spent to familiarize yourself with the machine and its
operations.
Since tractor makes and models vary, we recommend reading and following the
operators manual provided by the manufacturer pertaining to your particular unit.
Snow Plow Operation Section 3-2
OPERATION
PUSH ARM STOP POSITION
The Push Arm Stop height is controlled with the 3-point hitch control lever. Follow the
instructions for this control is the tractor operators manual. The 3-point should be set in
its lowest position. With the 3-point in its lowest position, adjust the 3-point arms so that
the Push Arm Stop is level to the ground
After the first day of operation, all bolts should be checked and
tightened securely. This should be done periodically to ensure the bolts do not
become loose and cause damage to the tractor or mower, or injury to the operator.
TRANSPORTING PLOWS
When driving from one site to the next, the following procedure should be followed.
The Front Plow should be raised to its highest position. The chains should be
repositioned to be tight with the plow raised.
The Side Plow should be raised to its transport position. First, raise the Kingpost all the
way to its top position. Secondly, bring the plow up by contracting the swing cylinder.
Verify that the Push Arm is contacting the rubber stop on the Push Arm Stop. If the side
plow isn’t agianst the rubber stop, lower the plow a couple of feet and then raise it back
up. Recheck the position of the plow. When the plow is raised all the way up and against
the rubber stop, shut the tractor off and walk around to the back to strap the chain around
the Push Arm.
Snow Plow Operation Section 3-3
OPERATION
TRANSPORTING MOWER ON A TRAILER
Transporting unit by flatbed trailer:
Most tractors with a side mounted plow attached will be over legal transporting
width (102” wide). For this reason, one of the following procedures must be
followed.
1: Transporting with side plow att ached: Use a loading dock or ramp to load
tractor onto the trailer. Center the tractor with the plows att ached between the sides
of the trailer. Make sure the side plow is fully raised and secured. Secure the
tractor to the trailer with chains. Obtain proper over-width permits and mark the
vehicle and plow as over-width as required be law . Check the tractor operators
manual for any tractor requirements to transport by flatbed trailer .
2: Transporting with side plow removed: Park the tractor and turn the engine of f.
Center the tractor and the plows between the sides of the trailer. Secure the tractor
and the plows to the trailer with chains.
Before conducting the inspection, make sure the T ractor engine is off, all rotation
has stop and the tractor is in the Park with the parking brake engaged. The
Mower head is resting on the ground (or is securely blocked up and supported)
and all hydraulic pressure has been relieved.
Snow removal equipment must be cared for and maintained regularly. Daily or
pre-route inspection and maintenance are necessary. Failure to do so may affect
efficiency and safety.
A visual inspection must be carried out after every 8 hours of operation. Look for
damaged components, bends, cracked welds or hydraulic leaks. REPAIR
IMMEDIATELY!
of use and to regularly check for loosened or missing fasteners. Replace any
damaged or missing fastener s immedi a tel y .
Because of the environment in which snow equipment is expected to operate,
hydraulic lines, fasteners, wearable or replaceable item s and warning decals may
become damaged by snow, ice and road debris. T hese items must be inspected
daily and replaced if necessary to avoid equipment damage or personal injury.
Lubrication of moving parts is of the utmost importance. Exposure to snow, ice,
salt and road debris will wash away lubrication quickly and it may be necessary
to inspect and reapply lubrication more than once a day.
It is recommended to re-torque all bolts after the first 8 hours
Page 2 of 3
END OF SEASON MAINTENANCE
GROUND ENGAGING COMPONENTS
CUTTING EDGES & GUARDS
Replace any broken cutting edges, unevenly or excessively worn cutting edges, and
broken or worn wear guards.
RUNNING GEAR
Replace broken, worn, or missing running gear shoes, and any damaged adjuster
leg components. Grease internal threads and sliding members (it’s best to
disassemble and grease directly; zerks aren’t as effective at greasing these areas).
HARDWARE
Replace missing or broken bolts. Proper torque is important! Use grade 8 plow
bolts for steel cutting edges.
HYDRAULICS
HOSES
Plug or cap any QC fittings or any open hose ends. Inspect hoses for any leaks or
potential leaks. Secure hoses with hose clamps.
CYLINDERS
Check for leaks, and any chrome rod dents or scratches. (If v-stack rod end seals
are leaking, a ¼ turn of the pack nut will often stop a small leak). Apply a light coat
of oil or grease on exposed rod surfaces.
FRAME AND MOLDBOARD
JOINTS
Check pins, bushings, and pivot bolts for wear. Make sure all keepers are in place.
Make sure shear bolts and pins are same as original equipment (usually grade 2).
Some drivers don’t like replacing shear pins and will install grade 8 replacements to
avoid replacing during a storm. These items are designed to shear to protect the
driver and the equipment.CHECK WELDMENTS FOR CRACKS.
REPLACE WORN OR BROKEN PARTS FOUND BY ABOVE INSPECTIONS.
Page 3 of 3
NOTES
JD62-6430 SNOW PLOW
PARTS
SECTION
Parts Section 5-1
P ARTS ORDERING GUIDE
The following instructions are offered to help eliminate needless delay and error in
processing purchase orders for the equipment in this manual.
1. The Parts Section is prepared in logical sequence and grouping of parts that
belong to the basic machine featured in this manual. Part Numbers and
Descriptions are given to help locate the parts and quantities required.
2. The Purchase Order must indicate the Name and Address of the person or
organization ordering the parts, who should be charged, and if possible, the serialnumber of the machine for which the parts are being ordered.
3. The purchase order must clearly list the quantity of each part, the complete
and correct part number, and the basic name of the part.
4. The manufacturer reserves the right to substitute parts where applicable.
5. Some parts may be unlisted items which are special production items not
normally stocked and are subject to special handling. Request a quotation for such
parts before sending a purchase order.
6. The manufacturer reserves the right to change prices without prior notice.
NOTE: When ordering replacement decals, refer to the part numbers and
descriptions listed in the safety section in the front of this manual.
For maximum safety and to guarantee optimum product reliability,
always use genuine
replacement parts may cause premature or catastrophic failure
which could result in serious injury or death.
Tiger replacement parts. The use of inferior
Direct any questions regarding parts to:
Tiger Corporation
3301 N. Louise Ave.
Sioux Falls, SD 57107
1-800-843-6849
1-605-336-7900
JD6030 SNOW PLOW Parts Section 5-2
P ARTS SECTION T ABLE OF CONTENTS
SECTIONPAGE
TRACTOR SPECIFIC PARTS:
TRACTOR MOUNT KIT - MAIN FRAME5-4
TRACTOR MOUNT KIT - FRONT HYDRAULICS5-5
TRACTOR MOUNT KIT - PUMP HOSES5-6
TRACTOR MOUNT KIT - SIDE HYDRAULICS5-8
3-POINT STOP & PUSH ARM5-10
MUL TIPLIER V ALVE MOUNTING5-12
3 & 4 FUNCTION MUL TIPLIER VALVE BREAKDOWN5-13
2 FUNCTION MUL TIPLIER VALVE BREAKDOWN5-14
1 FUNCTION MUL TIPLIER VALVE BREAKDOWN5-15
SAFETY LIGHTS5-16
JD6030 SNOW PLOW Parts Section 5-3
01-31-07
TRACTOR MOUNT KIT - MAIN FRAME
ITEMPART NO.QT YDESCRIPTION
1R EF*MAIN FRAME
2063001 181SIDE PLOW WELDMENT
3216883CAPSCREW,7/16 x 3-1/4,NC
4064201252PIN,1.50 X 4
5216773NYLOCK NUT,7/16,NC
6063001 161PUSH FRAME
7337648FLATWASHER,5/8,SAE,GR8
8217774NYLOCK NUT,5/8,NC
9063001 131HANGER FRAME
10338806FLATWASHER,3/4,SAE,GR8
1 1317314CAPSCREW,20MM x 50MM,2.5P,GR10.9
12323824CLAMP,HOSE
13272812CAPSCREW,20MM x 60MM,2.5P,GR10.9
146T22894CAPSCREW,5/8 x 2,NC,GR8
15218352CAPSCREW,3/4 x 2-3/4,NC
166T26072FLATWASHER,3/4,CUT
17220212FLATWASHER,3/4
18219932LOCKWASHER,3/4
19218252HEX NUT ,3/4,NC
206T30011PIN,1-1/2
JD6030 SNOW PLOW Parts Section 5-4
12-07-06
TRACTOR MOUNT KIT - FRONT HYDRAULICS
ITEMPART NO.QT YDESCRIPTION
1R EF*MAIN FRAME
2329005QUICK CPLR,MALE,1/2 x 1/2FOR
3332714ADAPTER,1/2MOR x 3/8MJ
4065005102HOSE,1/4 x 170
5065031472FITTING ,BLKHD,1/2MJ x 1/2MOR
6333822ELBOW,1/2MOR x 1/2MJX90
7065001641HOSE,1/4 x 216
8065002281HOSE,1/4 x 204
9065031481QUICK CPLR,FEM,1/2 x 1/2FOR
1 0REF2HOSE,1/2 *REFER T O FRONT PLOW ASSY
11REF2ELBOW *REFER T O FRONT PLOW ASSY
1 2REF1CUSHION V AL VE *REFER TO FRONT PLOW ASSY
JD6030 SNOW PLOW Parts Section 5-5
12-07-06
TRACTOR MOUNT KIT - PUMP HOSES
REPLACE EXISTING HOSES
IF NECESSARY
ITEMPART NO.QT YDESCRIPTION
1065002581HOSE,1-1/4 x 70 (FROM T ANK T O PUMP)
2TF48522FLANGE KIT ,#20
3065005121HOSE,1 x 70 (FROM PUMP TO BRAKE VAL VE)
JD6030 SNOW PLOW Parts Section 5-6
NOTES
PAGE INTENSIONALLY
LEFT BLANK
JD6030 SNOW PLOW Parts Section 5-7
TRACTOR MOUNT KIT - SIDE HYDRAULICS
JD6030 SNOW PLOW Parts Section 5-8
12-04-06
TRACTOR MOUNT KIT - SIDE HYDRAULICS
ITEMPART NO.QTY.DESCRIPTION
1R EF*MAIN FRAME
2329004QUICK CPLR,MALE,1/2 x 1/2MOR
3332716ADAPTER,1/2MOR x 3/8MJ
4065003452HOSE,1/4 x 171
5328102ELBOW,1/2ORB x 3/8MJ 90 ADJ
6340731ADAPTER,1/2MOR x 1/2FOR
7065030302ELBOW,3/8MJ x 3/8MJ 90 ADJ
80650051 12HOSE,1/4 x 161
JD6030 SNOW PLOW Parts Section 5-9
12-04-06
3-POINT STOP & PUSH ARM
JD6030 SNOW PLOW Parts Section 5-10
3-POINT STOP & PUSH ARM
ITEMPART NO.QTY.DESCRIPTION
1TB10361PIN,TOP LINK,3-POINT
2
3T F11202PIN,(CAPPED),1-1/8 x 3-7/8
4063001 1513PNT,SNWPLW
570300842TOPLOCK NUT ,5/8
62100-13602SPACER,1/4 (USE AS NEEDED)
72300-06201RUBBER STOP
870400062FLATWASHER,5/8,SAE
970201622CAPSCREW,5/8 x 3
1070200821CAPSCREW,3/4 x 3-1/2
1 170300301TOPLOCK NUT ,3/4
12219-06321PUSH BEAM ASSY
132100-03841HINGE ASSY
1470500282ROLL PIN,3/8 x 2
152100-12801PIN,1-1/4
TF 11433PIN, L YNCH, 7/16 x 2
JD6030 SNOW PLOW Parts Section 5-11
MULTIPLIER VALVE MOUNTING
ITEMPART NO.QTY.DESCRIPTION
1329002QUICK CPLR,MALE,1/2 x 1/2FOR
2333822ELBOW,1/2MOR x 1/2MJ X 90
3065002511HOSE,1/2 x 28
4215774NYLOCK NUT,5/16,NC
5065001221HOSE,1/2 x 30
6335282ADAPTER,1/2MOR x 1/2MJIC
7215794CAPSCREW,5/16 x 3/4,NC
8065051591KIT,HYD MUL TIPLIER,4 FUNCTION
9065031488QUICK CPLR,FEM,1/2 x 1/2FOR
10313298ADAPTER,1/2ORB x 1/2ORB ADJ
1 1*REFTRACTOR HARDWARE
12064110341MOUNT,MULTIPLIER
JD6030 SNOW PLOW Parts Section 5-12
3 & 4 FUNCTION MULTIPLIER VALVE BREAKDOWN
ITEMPART NO.QT YDESCRIPTION
1*REFSMALL NUT (NOT FOR P ARTS SALE)
206505165REFSOLENOID 12V SP
306505164REFN/C CARTRIDGE (SPOOL W/SHORT NUT)
4*REFMANIFOLD (NOT FOR P AR TS SALE)
*065102311CONTROLLER,4 BUTTON (NOT SHOWN)
*06505167REFO-RING SEAL KIT (NOT SHOWN)
JD6030 SNOW PLOW Parts Section 5-13
2 FUNCTION MULTIPLIER VALVE BREAKDOWN
ITEMPART NO.QT YDESCRIPTION
1*REFSMALL NUT (NOT FOR P AR TS SALE)
2065051654SOLENOID 12V SP
3065051632N/O CARTRIDGE (SPOOL W/SHORT NUT)
4*REFMANIFOLD (NOT FOR P ARTS SALE)
5065051642N/C CARTRIDGE (SPOOL W/SHORT NUT)
*065102301CONTROLLER,1 BUTTON (NOT SHOWN)
*06505167AVAILO-RING SEAL KIT (NOT SHOWN)
JD6030 SNOW PLOW Parts Section 5-14
1 FUNCTION MULTIPLIER VALVE BREAKDOWN
TWO REQUIRED
ITEMPART NO.QT YDESCRIPTION
1*REFT ALL NUT (NOT FOR P AR TS SALE)
2065051622SOLENOID 12V SS
3065051611N/O CARTRIDGE (POPPET W/T ALL NUT)
4*REFMANIFOLD (NOT FOR P ARTS SALE)
5065051601N/C CARTRIDGE (SPOOL W/SHORT NUT)
6*REFSHORT NUT (NOT FOR PARTS SALE)
7313291ADAPTER,1/2ORB x 1/2ORB ADJ
8329001QUICK COUPLER,MALE 1/2 x 1/2FOR
*065102301CONTROLLER,1 BUTTON (NOT SHOWN)
*06505166AVAILO-RING SEAL KIT (NOT SHOWN)
2. Remove and retain panel under right rear fender that protects wiring.
3. Remove and discard back three screws and clips securing the right rear fender to the cab.
4. Install mtg. bracket to points in previous step with three 1/4" x 3/4”NC bolts and nylock nuts.
5. Using the mounting bracket as a template to drill two holes (13/64 dia.) and tap(1/4"NC) in the
wheel well (Note: Use caution not to drill into the filter housing located behind the cab).
6. Secure bottom of mounting Bracket to wheel well with two 1/4" x 3/4"NC bolts and lockwashers.
7. Next remove the top cover of the tractor cab.
8. Drill two holes 5/8" dia, one in the fender under the air duct at the right rear corner of the cab and
the other at the right rear corner of the cab just inside the air duct.
9. Install grommets in the 5/8 “ dia holes.
10. Route wire from mounting bracket into the area that will be covered by the panel removed in step
2, then through grommets and up into area above cab, install wires ends into connector shell and
close strain relief (Note: Green wire to green wire when mated with adapter harness).
1 1. Splice the green wire from the adapter harness into the purple wire coming from right rear hazard
light using heat shrink butt connector.
12. Splice the black wire from the adapter harness into the black wire coming from right rear hazard
light using heat shrink butt connector.
13. Connect the adapter harness to the marker light harness.
14. T est for proper operation, the marker light should flash with hazards & right turn signal but should
burn steady when left turn signal is in use.
15. Reinstall top cover of tractor cab and panel in fender to protect wiring.
Tiger Corporation, 3301 N. Louise, Sioux Falls, South Dakota, warrant s to the
original Retail Customer, the new Tiger equipment is free of defects in material and
workmanship. Any p art of equipment that in Tiger’s judgement, show evidence of
such defects will be repaired or replaced without charge, provided that the failure of
part(s) shall have occurred within twelve (12) months from the date of delivery of
said equipment to the Retail Customer. Expendable components such as knives,
oil, chain sprockets, skid shoes, knife mounting disks and the like are excluded but
not limited to this warranty .
The Retail Customer must pay the transportation cost to and from the Tiger
Dealer’s service shop for warranty service. Warranty service will be performed by
the Tiger Dealer from whom the equipment was purchased, during service shop
regularly scheduled days and hours of operation.
All Tiger obligation under this warranty shall be terminated if the equipment is
modified or altered in ways not approved in writing by Tiger, if repair parts other than
genuine Tiger rep air part s have been used, or if the equipment has been subject to
misuse, neglect, accident, improper maintenance or improper operation.
Tiger Corporation reserves the right to make improvements in design or
changes in specification at any time without incurring any obligation to owners of
equipment previously sold.
No agent or person has authority to alter, add to or waive the above warranties
which are agreed to be in the only warranties, representations or promises,
expressed or implied, as to the quality or performance of the products covered and
which do not include any implied warranty of merchantability or fitness. In no event
will Tiger be liable for incident al or consequential damages or injuries, including, but
not limited to, loss of profits, rental or substitute equipment or other commercial
loss.
THERE ARE NO W ARRANTIES WHICH EXTEND
BEYOND THOSE EXPRESSED HEREIN.
It is the Purchasers obligation to sign the warranty registration form AFTER he /
she has
within this manual.
Read and Understands the Operation and SafetyInstructions stated
ONE LAST WORD
This manual cannot possibly cover all of the
potentially hazardous situations you will
encounter. By being familiar with the
safety rules, operating and maintenance
instructions in this manual you can help prevent
accidents. The objective of this manual is to
help make you a better operator. Remember ,
SAFETY IS YOU!
Y our safety and the safety of those around you
depends on YOU. Common sense should
play a large role in the operation of this machine.
Since we at Tiger Corporation are const antly striving to improve out product s, we
reserve the right to change specifications or design at any time.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.