Tiger Corporation 6020009 User Manual
TWIN ROTARY
Current as of 02/23/2010
ASSEMBLIES
Ford TS 100-110A
CAB, WOC
P A RTS LISTING WITH
MOUNTING AND OPERATING
INSTRUCTIONS
Tiger Corporation
3301 N. Louise Ave.
Sioux Falls, SD 57107
1-800-843-6849
1-605-336-7900
www.tiger-mowers.com
06020009
TO THE OWNER / OPERATOR / DEALER
All implements with moving parts are potentially hazardous. There is no substitute for a cautious,
safe-minded operator who recognizes the potential hazards and follows reasonable safety practices.
The manufacturer has designed this implement to be used with all its safety equipment properly
attached to minimize the chance of accidents.
BEFORE YOU START!! Read the safety messages on the implement and shown in this manual.
Observe the rules of safety and use common sense!
READ AND UNDERSTAND THIS MANUAL! Non–English speaking operators will need to GET
THE MANUAL TRANSLATED as needed!
Warranty Information: Read and understand the complete Warranty S tatement found in this manual. Fill out the
Warranty Registration form in full and return it within 90 days. Make certain the Serial Number of the machine is
recorded on the Warranty Card, and form that you retain.
FORWARD
This manual contains information about many features of the T iger mowing
and roadside maintenance equipment. Some of these include: Safety precautions,
Assembly instructions, Operations, Maintenance and Parts. This manual will also
assist you in the proper break-in, daily care, andtroubleshooting of your new
mower .
We recommend that you read carefully the entire manual before operating the
unit. Also, time spent in becoming fully acquainted with its performance features,
adjustments, and maintenance schedules will be repaid in a long and satisfactory
life of the equipment.
T roubleshooting - Please, before you call, help us to help you!
Please look at the equipment to observe what is happening, then:
• Classify the problem
• Hydraulic, electrical or mechanical - Read the trouble shooting section
• Tractor or T ruck chassis - Contact vehicle dealer
• If unable to correct the problem yourself, contact your local Tiger Dealer after
gathering:
• Machine model _______________________
• Serial number ________________________
• Dealer name _________________________
• Detailed information about the problem including results of troubleshooting
Attention Owner / Operator / Dealer: It is your obligation to read, and understand,
the warranty information section located at the back of this manual denoting that the
purchaser understands the safety issues relating to this machine and has received
and will read a copy of this manual.
If at any time, you have a service problem with your Tiger mower , Contact
your local dealer for service and parts needed.
MANUF ACTURED BY: DISTRIBUTED BY :
Tiger Corporation _____________________
3301 N. Louise Ave. _____________________
Sioux Falls, SD 57107 1-_____-_____-________
1-800-843-6849 1-_____-_____-________
1-605-336-7900
www .tiger-mowers.com
T ABLE OF CONTENTS
SAFETY_____________________________________________ 1-1
Safety Information__________________________________ 1-2
ASSEMBLY / MOUNTING SECTION_______________________2-1
OPERATION SECTION_________________________________ 3-1
MAINTENANCE SECTION______________________________ 4-1
PARTS SECTION_____________________________________ 5-1
Parts Ordering Guide_______________________________ 5-2
Parts Table of Contents______________________________ 5-3
Common Parts Section____________________________ 6-1
WARRANTY INFORMATION_____________________________ 7-1
This symbol means:
CAUTION – YOUR SAFETY IS AT RISK!
When you see this symbol, read and
follow the associated instructions carefully
or personal injury or damage may result.
Tiger is a registered trademark.
SAFETY
SAFETY
SECTION
Twin Rtry Safety Section 1-1
SAFETY
General Safety Instructions and Practices
A safe and careful operator is the best operator. Safety is of primary import ance to the
manufacturer and should be to the owner / operator . Most accidents can be avoided by being
aware of your equipment, your surroundings, and observing certain precautions. The first
section of this manual includes a list of Safety Messages that, if followed, will help protect the
operator and bystanders from injury or death. Read and understand these Safety Messages
before assembling, operating or servicing this mower . This equipment should only be
operated by those persons who have read the Manual, who are responsible and trained, and
who know how to do so safely and responsibly .
The Safety Alert Symbol combined with a Signal Word, as seen below , is used
throughout this manual and on decals which are attached to the equipment. The
Safety Alert Symbol means: “A TTENTION! BECOME ALERT! YOUR SAFETY IS
INVOLVED!” The symbol and signal word are intended to warn the owner /
operator of impending hazards and the degree of possible injury when operating
this equipment.
Practice all usual and customary safe working precautions and
above all -- remember safety is up to YOU! Only YOU can
prevent serious injury or death from unsafe practices.
Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH
OR VERY SERIOUS INJURY.
Indicates an imminently hazardous situation that, if not avoided, COULD result in
DEA TH OR SERIOUS INJURY.
Indicates an imminently hazardous situation that, if not avoided, MA Y result in MINOR
INJURY.
IMPORTANT!
NOTE: Identifies points of particular interest for more efficient or convienient operation or
Identifies special instructions or procedures that, if not strictly observed, could result
in damage to, or destruction of the machine, attachments or the enviroment.
repair. (SG-1)
READ, UNDERST AND, and FOLLOW the following Safety Messages.
Serious injury or death may occur unless care is taken to follow the
warnings and instructions stated in the Safety Messages. Always use
good common sense to avoid hazards. (SG-2)
Twin rtry Safety Section 1-2
SAFETY
PELIGRO!
DANGER!
WARNING!
WARNING!
Si no lee Ingles, pida ayuda a alguien que
si lo lea para que le traduzca las medidas
de seguridad. (SG-3)
Never operate the Tractor or Implement until you have read and
completely understand this Manual, the Tractor Operator’s Manual,
and each of the Safety Messages found in the Manual or on the Tractor
and Implement. Learn how to stop the tractor engine suddenly in an
emergency. Never allow inexperienced or untrained personnel to
operate the Tractor and Implement without supervision. Make sure
the operator has fully read and understands the manuals prior to
operation. (SG-4)
Always maintain the safety decals in good readable condition. If the
decals are missing, damaged, or unreadable, obtain and install replacement decals immediately. (SG-5)
Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in
such a way as to be clearly visible and legible. When transporting the
Equipment use the Tractor flashing warning lights and follow all local traffic
regulations. (SG-6)
!
LEA EL
INSTRUCTIVO!
WARNING!
WARNING!
DANGER!
Operate this Equipment only with a Tractor equipped with an
approved roll-over-protective system (ROPS). Always wear seat
belts. Serious injury or even death could result from falling off the
tractor--particularly during a turnover when the operator could be
pinned under the ROPS. (SG-7)
Do not modify or alter this Implement. Do not permit anyone to modify
or alter this Implement, any of its components or any Implement
function. (SG-8)
BEFORE leaving the tractor seat, always engage the brake and/or set
the tractor transmission in parking gear, disengage the PTO, stop the
engine, remove the key, and wait for all moving parts to stop. Place the
tractor shift lever into a low range or parking gear to prevent the tractor
from rolling. Never dismount a Tractor that is moving or while the engine
is running. Operate the Tractor controls from the tractor seat only.
(SG-9)
Twin Rtry Safety Section 1-3
SAFETY
DANGER!
DANGER!
WARNING!
DANGER!
Never allow children or other persons to ride on the Tractor or Implement.
Falling off can result in serious injury or death.
(SG-10)
Never allow children to operate or ride on the Tractor or Implement.
(SG-11)
Do not mount the tractor while the tractor is moving. Mount the tractor
only when the tractor and all moving parts are completely stopped.
(SG-12)
Start tractor only when properly seated in the tractor seat. Starting a
tractor in gear can result in injury or death. Read the tractor operators
manual for proper starting instructions. (SG-13)
DANGER!
Never work under the Implement, the framework, or any lifted component unless the Implement is securely supported or blocked up to
prevent sudden or inadvertent falling which could cause serious injury
or even death. (SG-14)
DANGER! Do not operate this Equipment with hydraulic oil leaking. Oil is
expensive and its presence could present a hazard. Do not check for
leaks with your hand! Use a piece of heavy paper or cardboard. Highpressure oil streams from breaks in the line could penetrate the skin
and cause tissue damage including gangrene. If oil does penetrate the
skin, have the injury treated immediately by a physician knowledgeable and skilled in this procedure. (SG-15)
Twin rtry Safety Section 1-4
SAFETY
WARNING! The operator and all support personnel should wear hard hats,
safety shoes, safety glasses, and proper hearing protection at all
times for protection from injury including injury from items thrown by
the equipment. (SG-16)
CAUTION!
WARNING!
PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PERMANENT HEARING LOSS! Tractors with or without an Implement at-
tached can often be noisy enough to cause permanent hearing loss.
We recommend that you always wear hearing protection if the noise in
the operator’s position exceeds 80db. Noise over 85db over an extended period of time will cause severe hearing loss. Noise over 90db
adjacent to the operator over an extended period of time will cause
permanent or total hearing loss. Note: Hearing loss from loud noise
[from tractors, chain saws, radios, and other such sources close to the
ear] is cumulative over a lifetime without hope of natural recovery.
(SG-I7)
Transport only at safe speeds. Serious accidents and injuries
can result from operating this equipment at unsafe speeds.
Understand the T ractor and Implement and how it handles before
transporting on streets and highways. Make sure the Tractor
steering and brakes are in good condition and operate properly .
Before transporting the Tractor and Implement, determine
the safe transport speeds for you and the equipment.
Make
sure you abide by the following rules:
1.
T est the tractor at a slow speed and increase the speed slowly.
Apply the brakes smoothly to determine the stopping characteristics
of the Tractor and Implement. As you increase the speed of the
Tractor the stopping distance increases. Determine the maximum
safe transport speed for you and this equipment.
Test the equipment at a slow speed in turns. Increase the speed
2.
through the turn only after you determine that it is safe to operate
at a higher speed. Use extreme care and reduce your speed
when turning sharply to prevent the tractor and implement from
turning over. Determine the maximum safe turning speed for you
and this equipment before operating on roads or uneven ground.
Only transport the Tractor and Implement at the speeds that you
3.
have determined are safe and which allow you to properly
control the equipment.
Be aware of the operating conditions. Do not operate the Tractor
with weak or faulty brakes. When operating down a hill or on wet
or rain slick roads, the braking distance increases: use extreme
care and reduce your speed. When operating in traffic always use
the Tractor’s flashing warning lights and reduce your speed. Be
aware of traffic around you and watch out for the other guy. (SG-19)
Twin Rtry Safety Section 1-5
SAFETY
WARNING! Never attempt to lubricate, adjust, or remove material from the
Implement while it is in motion or while tractor engine is running. Make
sure the tractor engine is OFF before working on the Implement.
(SG-20)
WARNING!
WARNING!
DANGER!
Periodically inspect all moving parts for wear and replace when
necessary with authorized service parts. Look for loose fasteners,
worn or broken parts, and leaky or loose fittings. Make sure all pins
are properly secured. Serious injury may occur from not maintaining
this machine in good working order.
Always read carefully and comply fully with the manufacturers instructions when handling oil, solvents, cleansers, and any other chemical
agent. (SG-22)
Never run the tractor engine in a closed building or without adequate
ventilation. The exhaust fumes can be hazardous to your health.
(SG-21)
(SG-23)
DANGER!
DANGER!
KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement
and possible serious injury or death. (SG-24)
Never allow children to play on or around Tractor or Implement. Children
can slip or fall off the Equipment and be injured or killed. Children can
cause the Implement to shift or fall crushing themselves or others. (SG-25)
Twin rtry Safety Section 1-6
SAFETY
DANGER!
DANGER!
WARNING!
NEVER use drugs or alcohol immediately before or while operating the
Tractor and Implement. Drugs and alcohol will affect an operator’s
alertness and coordination and therefore affect the operator’s ability to
operate the equipment safely. Before operating the Tractor or Implement, an operator on prescription or over-the-counter medication must
consult a medical professional regarding any side effects of the medication that would hinder their ability to operate the Equipment safely.
NEVER knowingly allow anyone to operate this equipment when their
alertness or coordination is impaired.
operator or others could result if the operator is under the influence of
drugs or alcohol. (SG-27)
Operate the Tractor and/or Implement controls only while properly seated
in the Tractor seat with the seat belt securely fastened around you.
Inadvertent movement of the Tractor or Implement may cause serious
injury or death. (SG-29)
Mow only in conditions where you have clear visibility in daylight or with
adequate artificial lighting. Never mow in darkness or foggy conditions
where you cannot clearly see at least 100 yards in front and to the sides of
the tractor and mower. Make sure that you can clearly see and identify
passersby, steep slopes, ditches, drop-offs, overhead obstructions, power
lines, debris and foreign objects. If you are unable to clearly see this type
of items discontinue mowing. (SGM-1)
Serious injury or death to the
DANGER!
DANGER!
There are obvious and hidden potential hazards in the operation of this
Mower. REMEMBER! This machine is often operated in heavy brush
and in heavy weeds. The Blades of this Mower can throw objects if
shields are not properly installed and maintained. Serious injury or
even death may occur unless care is taken to insure the safety of the
operator, bystanders, or passersby in the area. Do not operate this
machine with anyone in the immediate area. Stop mowing if anyone
is within 100 yards of mower. (SGM-2)
All Safety Shields, Guards and Safety devices including (but not limited
to) - the Deflectors, Steel Guards, Gearbox Shields, PTO integral shields,
and Retractable Door Shields should be used and maintained in good
working condition. All safety devices should be inspected carefully at
least daily for missing or broken components. Missing, broken, or worn
items must be replaced at once to reduce the possibility of injury or death
from thrown objects, entanglement, or blade contact. (SGM-3)
Twin Rtry Safety Section 1-7
SAFETY
DANGER! The rotating parts of this machine have been designed and tested for
rugged use. However, the blades could fail upon impact with heavy,
solid objects such as metal guard rails and concrete structures. Such
impact could cause the broken objects to be thrown outward at very
high velocities. To reduce the possibility of property damage, serious
injury, or even death, never allow the cutting blades to contact such
obstacles. (SGM-4)
WARNING!
WARNING!
WARNING!
Extreme care should be taken when operating near loose objects such
as gravel, rocks, wire, and other debris. Inspect the area before
mowing. Foreign objects should be removed from the site to prevent
machine damage and/or bodily injury or even death. Any objects that
cannot be removed must be clearly marked and carefully avoided by
the operator. Stop mowing immediately if blades strike a foreign
object. Repair all damage and make certain rotor or blade carrier is
balanced before resuming mowing.
Many varied objects, such as wire, cable, rope, or chains, can become
entangled in the operating parts of the mower head. These items could
then swing outside the housing at greater velocities than the blades. Such
a situation is extremely hazardous and could result in serious injury or
even death. Inspect the cutting area for such objects before mowing.
Remove any like object from the site. Never allow the cutting blades to
contact such items. (SGM-6)
Mow at the speed that you can safely operate and control the tractor and
mower. Safe mowing speed depends on terrain condition and grass type,
density, and height of cut. Normal ground speed range is from 0 to 5 mph.
Use slow mowing speeds when operating on or near steep slopes,
ditches, drop-offs, overhead obstructions, power lines, or when debris and
foreign objects are to be avoided. (SGM-7)
(SGM-5)
WARNING!
WARNING!
DANGER!
WARNING!
Avoid mowing in reverse direction when possible. Check to make sure
there are no persons behind the mower and use extreme care when
mowing in reverse. Mow only at a slow ground speed where you can safely
operate and control the tractor and mower. Never mow an area that you
have not inspected and removed debris or foreign material. (SGM-8)
Do not put hands or feet under mower decks. Blade Contact can result
serious injury or even death. Stay away until all motion has stopped and
the decks are securely blocked up. (SGM-9)
Replace bent or broken blade with new blades. NEVER ATTEMPT TO
STRAIGHTEN OR WELD ON BLADES SINCE THIS WILL LIKELY
CRACK OR OTHERWISE DAMAGE THE BLADE WITH SUBSEQUENT FAILURE AND POSSIBLE SERIOUS INJURY FROM THROWN
BLADES. (SGM-10)
Do not mow with two machines in the same area except with Cab tractors
with the windows closed. (SGM-11)
Twin rtry Safety Section 1-8
SAFETY
DANGER!
WARNING!
Rotary Mowers are capable under adverse conditions of throwing
objects for great distances (100 yards or more) and causing serious
injury or death. Follow safety messages carefully.
STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UNLESS:
-Front and Rear Deflectors are installed and in good,
working condition;
-Mower Head is running close to and parallel to the ground
without exposed Blades;
-Passersby are outside the existing thrown-object zone;
-All areas have been thoroughly inspected and all foreign
material such as rocks, cans, glass, and general debris
has been removed.
NOTE:
Each Rear Wheel must have a minimum of 1,000 pounds contact with
the surface to prevent lateral instability and possible tip-over which
could result in serious bodily injury or even death. Widen the wheel
tread and add weights if needed. Refer to the mounting instructions
or call Customer Service if you need assistance with Counterweight
Procedure. (SFL-3)
Where there are grass and weeds high enough to hide debris
that could be struck by the blades, the area should be: inspected and large debris removed, mowed at an intermediate
height, inspected closely with any remaining debris being removed, and mowed again at desired final height. (SFM-6)
WARNING!
WARNING!
WARNING!
Do not operate Mower if excessive vibration exists. Shut down PTO
and the Tractor engine. Inspect the Mower to determine the source
of the vibration. If Mower blades are missing or damaged replace
them immediately. Do not operate the mower until the blades have
been replaced and the Mower operates smoothly. Operating the
Mower with excessive vibration can result in component failure and
broken objects to be thrown outward at very high velocities. To reduce
the possibility of property damage, serious injury, or even death, never
allow the Mower to be operated with blades missing. (SFL-4)
Do not let the Blades turn when the Mower Deck is raised for any
reason, including clearance or for turning. Raising the Mower
deck exposes the Cutting Blades which creates a potentially
serious hazard and could cause serious injury or even death from
objects thrown from the Blades. (SRM-7)
Never leave Tractor and Implement unattended while the implement is in
the lifted position. Accidental operation of lifting lever or a hydraulic failure
may cause sudden drop of unit with injury or death by crushing. To
properly park the implement when disconnecting it from the tractor, lower
the stand and put the retaining pin securely in place, or put a secure
support under the A-Frame. Lower the implement carefully to the ground.
Do not put hands or feet under lifted components. (SPT-1)
Twin Rtry Safety Section 1-9
WARNING!
SAFETY
Be particularly careful when transporting the Implement with the Tractor. Turn
curves or go up hills only at a low speed and using a gradual steering angle. Rear
mounted implements move the center of gravity to the rear and remove weight from
the front wheels. Make certain, by adding front ballast, that at least 20% of the
tractor’s weight is on the front wheels to prevent rearing up, loss of steering control
or Tractor tip-over. Slow down on rough or uneven surfaces to prevent loss of
steering control which could result in property damage or possible injury. Do not
transport unless 3-Point lift lever is fully raised and in the latched transport position.
Dropping implement in transport can cause serious damage to the tractor and/or
Implement and possibly cause the operator or others to be injured or killed. (S3PT-2)
WARNING!
DANGER!
WARNING!
The rotating parts of this machine continue to rotate even after the Tractor has been
turned off. The operator should remain in his seat for 60 seconds after the brake
has been set, the PTO disengaged, the tractor turned off, and all evidence of
rotation has ceased. (SBM-5)
“Wait a minute...Save a life!”
There are obvious and hidden potential hazards in the operation of this
Implement as in all power-driven or pulled equipment. REMEMBER!
This machine is often operated in rough terrain conditions that include tall
grass, weeds, gullies, holes, slopes, hidden obstructions and the like.
Serious injury or even death may occur unless care is taken to assure the
safety of the operator and bystanders in the area. Do not operate this
machine with anyone in the immediate area. (S3PT-7)
Relieve hydraulic pressure prior to doing any maintenance or repair work
on the Implement. Place the Implement on the ground or securely
blocked up, disengage the PTO, and turn off the tractor engine. Push
and pull the Remote Cylinder lever in and out several times prior to
starting any maintenance or repair work. (S3PT-9)
DANGER!
DANGER!
This Implement is wider than the Tractor. Be careful when operating
or transporting this equipment to prevent the Implement from running
into or striking sign posts, guard rails, concrete abutments or other
solid objects. Such an impact could cause the Implement and Tractor
to pivot violently resulting in loss of steering control, serious injury, or
even death. Never allow the Implement to contact obstacles. (S3PT-12)
The flail cutter shaft is designed for standard rotation (same
rotation as the tractor wheels during forward travel). Never operate the
cutter shaft in the reverse rotation. Operating this mower in reverse
rotation may cause objects to be thrown out the front of the mower
head.
Twin rtry Safety Section 1-10
SAFETY
WARNING!
Engine Exhaust, some of its constituents, and certain components contain or
emit chemicals known to the state of California to cause cancer and birth or other
reproductive harm.
WARNING!
Battery posts, terminals and related accessories contain lead and lead
compounds, chemicals known to the state of California to cause cancer and
birth or other reproductive harm. Wash hands after handling!
Tiger mowers use balanced and matched system components for blade carriers, blades, cuttershafts, knives, knife hangers, rollers, drive-train components and bearings. These parts are made and
tested to Tiger specifications. Non-genuine “will fit” parts do not consistently meet these specifications.
The use of “will fit” parts may reduce mower performance, void mower warranties and present a safety
hazard. Use genuine Tiger mower parts for economy and safety.
SEE YOUR DEALER
In addition to the design and configuration of this Implement, including Safety Signs and Safety
Equipment, hazard control and accident prevention are dependent upon the awareness,
concern, prudence, and proper training of personnel involved in the operation, transport,
maintenance, and storage of the machine. Refer also to Safety Messages and operation
instruction in each of the appropriate sections of the Tractor and Equipment Manuals. Pay
close attention to the Safety Signs affixed to the Tractor and Equipment. (SG-18)
Twin Rtry Safety Section 1-11
SAFETY
P ART NO.
LOCA TION
22839
MOWER DECK
22840
INSIDE OF CAB
Twin rtry Safety Section 1-12
24028
MOWER DECK
10” x 5.5” 31522
MOWER DECK
18.25” x10” 31523
HYDRAULIC T ANK
SAFETY
P ART NO.
LOCA TION
42350
MOWER DECK
33743
INSIDE OF CAB
42399
MOWER DECK
Twin Rtry Safety Section 1-13
42400
MOWER DECK
SAFETY
P ART NO.
LOCA TION
6T3217
MOWER DECK
6T3219
INSIDE OF CAB
Twin rtry Safety Section 1-14
6T3220
FRONT PUMP MOUNT
6T3221
INSIDE OF CAB
SAFETY
P ART NO.
LOCA TION
6T3222
INSIDE OF CAB
INSIDE OF CAB
6T3224
MOWER DECK
6T3230
INSIDE OF CAB
Twin Rtry Safety Section 1-15
SAFETY
P ART NO.
LOCA TION
6T3233
HYDRAULIC T ANK
6T3234
INSIDE OF CAB
Twin rtry Safety Section 1-16
6T3236
MOWER DECK
HYDRAULIC T ANK
6T3243
INSIDE OF CAB
SAFETY
P ART NO.
LOCA TION
6T3249A
MOWER DECK
6T3261
MOWER DECK
Twin Rtry Safety Section 1-17
TB1011
MOWER DECK
SAFETY
Twin rtry Safety Section 1-18
34852
HYDRAULIC TANK
SAFETY
ITEM PART NO. QTY. DESCRIPTION
50023 AVAIL MANUAL CANISTER COMPLETE
1 00776031 1 ROUND MANUAL CANISTER
33997 1 DECAL, SHEET, MANUAL CANISTER
2 * DECAL
3 * DECAL
4 * DECAL
5 * AVAIL SPECIFIC PRODUCT MANUAL
6 33753 1 E M I SAFETY MANUAL
7 34296 1 FRONT ADHESIVE PAD
8 34297 1 REAR ADHESIVE PAD
9 6T1823 4 ZIP TIE 14” LONG
NOTE:
The manual canister can be bolted, zip tied or adhered to a variety of
surfaces. Locate a protected area within the view of the operator. Then
select an installation method and attach the canister . CAUTION - A VOID
DRILLING HOLES INTO UNKNOWN AREAS, wires and other parts may
be located behind these areas. When adhering the canister to a surface,
thoroughly clean that surface before installing the canister .
Twin Rtry Safety Section 1-19
SAFETY
FEDERAL LAWS AND REGULATIONS
This section is intended to explain in broad terms the concept and effect of federal laws and regulations
concerning employer and employee equipment operators. This section is not intended as a legal
interpretation of the law and should not be considered as such.
Employer-Employee Operator Regulations
U.S. Public Law 91-596 (The Williams-Steiger Occup ational and Health Act of 1970) OSHA
This Act Seeks:
“...to assure so far as possible every working man and woman in the nation safe and
healthful working conditions and to preserve our human resources...”
DUTIES
Sec. 5 (a) Each employer(1) shall furnish to each of his employees employment and a place of employment which
are free from recognized hazards that are causing or are likely to cause death or serious
physical harm to his employees;
(2) shall comply with occupational safety and health standards promulgated under this
Act.
(b) Each employee shall comply with occupational safety and health standards and all
rules, regulations and orders issued pursuant to this Act which are applicable to his
own actions and conduct.
OSHA Regulations
OSHA regulations state in part: “At the time of initial assignment and at least annually
thereafter , the employer shall instruct every employee in the safe operation and servicing
of all equipment with which the employee is, or will be involved.”
Employer Responsibilities:
T o ensure employee safety during Tractor and Implement operation, it is the employer’s responsibility
to:
1. Train the employee in the proper and safe operation of the T ractor and Implement.
2. Require that the employee read and fully understand the Tractor and Implement Operator’s manual.
3. Permit only qualified and properly trained employees to operate the Tractor and Implement.
4. Maintain the Tractor and Implement in a safe operational condition and maintain all shields and
guards on the equipment.
5. Ensure the Tractor is equipped with a functional ROPS and seat belt and require that the employee
operator securely fasten the safety belt and operate with the ROPS in the raised position at all
times.
6. Forbid the employee operator to carry additional riders on the Tractor or Implement.
7. Provide the required tools to maintain the T ractor and Implement in a good safe working condition
and provide the necessary support devices to secure the equipment safely while performing repairs
and service.
Child Labor Under 16 Years of Age
Some regulations specify that no one under the age of 16 may operate power machinery. It is your
responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of
Labor, Employment Standard Administration, W age & Home Division, Child Labor Bulletin #102.)
Twin rtry Safety Section 1-20
ASSEMBLY
SECTION
Assembly Section 2-1
ASSEMBLY
Before attempting to mount or service your Tiger mower, it is important
to read and understand all of the information in the Safety section of this
manual.
Check complete shipment list against the packing list to make sure there are no
shortages. Make certain the tractor model is the appropriate one for the mower
received!
Use a floor jack, hoist or fork lift to lift or raise heavy parts whenever
possible whether mentioned or not.
Read and understand the entire assembly section instructions before
attempting to mount your Tiger mower. Refer to the parts section of this manual
for detailed illustrations to locate all parts.
TRACTOR PREP ARA TION
A: Remove right hand steps.
B: Disconnect battery cables.
C: Remove battery, battery box and existing bracket.
D: Remove engine side panels, or raise hood to access front pulley.
E: Remove plugs from tractor casting where main frame and pump mount will
be attached.
F: Install battery bracket supplied in the kit using existing hardware.
Assembly Section 2-2
ASSEMBLY
ADJUSTING REAR WHEELS
Raise rear of tractor onto jack-stands. Follow the instructions in the tractor
owners manual for adjusting tires and rims to 72” center for side mounted
mowers and 79.8” for boom mowers. NOTE: This may require switching the
wheels to opposite sides of tractor.
CRANKSHAFT ADAPTER
If necessary remove the four cap-screws from the crankshaft pulley. Then
install the crankshaft adapter and spacer to the pulley with cap-screws and lockwashers as shown in the parts section.
CABLE CONTROL LEVER STAND
Place the front edge of the support bracket 2 ¾” back from the lower right front
window. Rotate stand to be 2” from the right door frame as shown below. Be
sure that the location of the stand will allow clearance between the cable control
handles and all existing interior levers, etc.
Drill 3 holes to match control bracket and secure with cap-screws and nylock
nuts noted in parts section.
Cut a 2 ¼” hole in the floor from inside the cab. This hole is to be located 2-1/2”
up from floor, and 4” from the met al edge by the right door. Install trim lock around
the metal edges of the hole, then route the cables through the hole. Next, wrap the
cables with the 6” split hose at the point they pass through the hole, and secure with
zip-ties.
Assembly Section 2-3
ASSEMBLY
LIFT VALVE MOUNT
Install the valve mounting bracket to the inside of the right and left rear fender
frame tube as shown below. Align the valve mounting plate with the drilled holes.
Mark the center of one of the holes above and in line with the slotted holes in the
valve plate. Do not use any holes that will be used to mount the valve on the plate.
Mount the lift valve with the supplied hardware. Refer the parts section for the
details.
MAIN FRAME MOUNTING
Raise front of tractor as needed and slide the main frame under tractor from
right hand side. With an overhead hoist and / or jack-stands, raise the frame up to
the correctly matching mounting holes. Install spacer blocks and shims as
needed. Install cap-screws and all other hardware as shown in main frame parts
section. Remove the cap-screws one at a time and apply a thread locking agent,
then reinsert the cap-screws and tighten / torque to values noted in the torque
chart located in the maintenance section of this manual.
SOLENOID BRAKE VALVE
Install a solenoid valve the mounting bracket with the supplied hardware. While
installing fittings to the brake valve, the electrical coil on the spool must be removed to
make room. When reinstalling the coil, it is important to use no more than 5 ft. lbs.
(or 60 in. lbs.) torque. Over torque to the coil will result in hydraulic failure of spool.
Assembly Section 2-4
Loading...