Page 1
TWR-180
TWR-120
ROTARY CUTTER
Published 2006-06-29 Serial #C31400382705-C31400552806 Inclusive Part No. C314TG010P
Serial #C31500030705-C31500039806 Inclusive
PARTS MANUAL
An Operators Manual with IMPORTANT Safety, Assembly, Operation
and Maintenance information was packaged with this Parts Manual
during final inspection at the factory. If the Operators Manual is
missing at any time, please contact Tiger Corporation to receive your
free replacement manual.
3301 N. Louise Ave.
Sioux Falls, SD 57107
1-800-843-6849
1-605-336-7900
www.tiger-mowers.com
Tiger Corporation
© 2006 Alamo Group Inc.
Page 2
PARTS ORDERING GUIDE
The following instructions are offered to help eliminate delay and error in processing
purchase orders for the equipment in this section.
1. The Purchase Order must include the name and address of the person or organization ordering
the parts, who should be charged, and if possible, the serial number of the machine for which the
parts were ordered.
2. The Purchase Order must clearly list the quantity of each part, the complete and correct part
number, and the description of the part.
3. The Manufacturer reserves the right to substitute parts where applicable.
4. The Manufacturer reserves the right to change prices without prior notice.
NOTE: Please refer to the Safety Section in the front of the Operators Manual for the proper
Part Number when ordering Replacement Safety Decals. Safety decals are
available free of charge from the Manufacturer.
NOTE: If the Operators Manual does not accompany this Parts Manual please obtain one,
free of charge from the Manufacturer. DO NOT operate this implement unless you
READ, UNDERSTAND, and FOLLOW the Safety and Operation instructions
contained in the Operators Manual
NOTE: Please note that the appearance of some parts may vary from the artwork shown
in the Manual.
For maximum safety and to guarantee optimum product reliability, always use genuine
OEM Parts. The use of inferior replacement parts may cause premature or
catastrophic failure which could result in serious injury or death. Direct any questions
regarding parts to:
Tiger Corporation
3301 N. Louise Ave.
Sioux Falls, SD 57107
1-800-843-6849
1-605-336-7900
www.tiger-mowers.com
-1-
Page 3
TABLE OF CONTENTS
CENTER SECTION FRAME .................................................. -3-
WING FRAME, RIGHT ....................................................... -5-
WING FRAME, LEFT ........................................................ -7-
HITCH FRAME AND CENTER WHEEL STANDARD ............................... -9-
10' SKIRT ASSEMBLY ...................................................... -11-
HITCH JACK, 15" SIDE WIND (232-800) ........................................ -12-
HUB, AXLES & TIRES ...................................................... -13-
DRIVELINE SHIELDING .................................................... -15-
CHAIN GUARDS .......................................................... -17-
BLADE CARRIERS ........................................................ -19-
WING WINCH KIT (C312-300) ................................................ -21-
WING LIFT CIRCUIT, SINGLE ACTING ........................................ -22-
WING LIFT CYLINDER, MONARCH (100-3701) .................................. -23-
PHASING CIRCUIT ........................................................-24-
PHASING CYLINDERS, MONARCH ........................................... -25-
SPOOL VALVE KIT, S150 (C301-805) ......................................... -26-
SPOOL VALVE KIT, S100 (C302-805) ......................................... -28-
TRACTOR UNIVERSAL JOINT W/ 80
TRACTOR UNIVERSAL JOINT W/ 80
WING UNIVERSAL JOINT, SIZE 6 (340-6013) ................................... -33-
CENTER UNIVERSAL JOINT, SIZE 6 .......................................... -35-
SLIP CLUTCH (341-6322, 341-6323) .......................................... -36-
SLIP CLUTCH (341-6324) ................................................... -38-
DIVIDER GEARBOX ....................................................... -39-
CW GEARBOX, WING (330-7030) ............................................ -41-
CCW GEARBOX, WING (330-7031) ...........................................-43-
CW GEARBOX, CENTER, 540 RPM (330-7035) .................................. -45-
CW GEARBOX, CENTER, 1000 RPM (330-7036) ................................. -47-
TRANSPORT KITS ........................................................ -49-
PARTS INDEX ............................................................ -50-
o
C.V., SIZE 8 (340-850) ...................... -29-
o
C.V., SIZE 6 (340-648) ...................... -31-
-2-
Page 4
CENTER SECTION FRAME
June 27, 2006
-3-
Page 5
CENTER SECTION FRAME
Ref. Part No. Description Qty.
1 C314-101 Center section assembly 1
2 228-012 Hose organizer 2
3 250-112 Bolt, 3/4 x 3 UNC 6
4 270-004 Lock nut, 5/8 UNC 10
5 250-093 Bolt, 5/8 x 1-3/4 UNC 2
6 256-006 Flat washer, 5/8 2
7 C310-112 Skid mount assembly 2
8 250-084 Bolt, 5/8 x 4-1/2 UNC 4
9 C301-113 Wing lift spacer plate 2
10 250-060 Bolt, ½ x 1-3/4 UNC 3
11 C310-144 Retainer pin, 1 x 5-3/16 U.L 1
12 256-011 Flat washer, 1/2 3
13 270-007 Lock nut, 1/2 UNC 3
14 256-001 Flat washer, 1 3
15 262-006 Roll pin, 3/8 x 2 3
16 C310-143 Retainer pin, 1 x 2-3/4 U.L. 2
17 250-112 Bolt, 3/4 x 3 UNC (light truck tire) 2
250-111 Bolt, 3/4 x 4 UNC (laminated & aircraft) 2
18 C310-105 Cylinder lug adjustment assembly. 1
19 C310-120 Spacer plate, 1" (light truck tire) 1
C310-120 Spacer plate, 1" (laminated & aircraft tire) 2
* See “Fixed Knife Shredder Kit” parts page for additional spacer plates required
* See “Sod Kit” parts page for special spacer plate requirements
20 C301-118 Wing lock pin, 1 x 5-9/16 U.L. 2
21 250-023 Bolt, 3/8 x 1-3/4 UNC 5
22 256-017 Flat washer, 3/8 4
23 300-012 Lynch pin, 1/4 3
24 C312-119 Slow moving vehicle sign stand 1
25 270-017 Lock nut, 3/8 UNC 8
26 250-019 Bolt, 3/8 x 1-1/4 UNC 2
27 270-001 Lock nut, 3/4 UNC 8
28 C310-115 Bolt access cover plate 1
29 255-013 Lock washer, 3/8 2
30 250-018 Bolt, 3/8 x 1 UNC 4
31 330-7035 Gear box, 540 RPM 1
330-7036 Gear box, 1000 RPM 1
33 150-32 Complete, SMV sign 1
34 330-930 Splitter box, 540 RPM 1
330-931 Splitter box, 1000 RPM 1
35 250-090 Bolt, 5/8 x 2 UNC 4
36 C310-127 Transport lock pin, 1 x 5-5/16 U.L. 1
37 280-200 Manual Box 1
38 256-018 Washer, 1/4" 2
39 250-002 Bolt, 1/4" x 1" UNC 2
40 270-025 Locknut, 1/4" UNC 2
41 C000-001 Hose clamp 1
42 262-005 Roll Pin, 3/8 x 2-1/2" 1
June 27, 2006
-4-
Page 6
WING FRAME, RIGHT
June 27, 2006
-5-
Page 7
WING FRAME, RIGHT
Ref. Part No. Description Qty.
1 C314-155 Wing assembly, right 1
2 752-014 Hinge pin, 15" O.A. 4
3 C310-140 Hinge spacer tube, 13-7/8" O.A. 2
5 262-011 Roll Pin, 3/8 x 1-3/4 6
6 C310-141 Hinge spacer tube, 10-3/8" O.A. 1
7 262-006 Roll pin, 3/8 x 2 5
8 256-001 Flat washer, 1 6
9 C301-140 Pin, 1 x 3-13/32" O.A. 2
10 C301-114 Floating lug 2
13 330-7031 Gearbox, CCW 1
* CW Gearbox (330-7030) is required for fixed knife, material distribution, and sod kits.
See your Schulte Dealer
14 250-201 Plow bolt, ½ x 1-1/2 UNC 3
16 C310-135 Outer wing skid, standard 1
17 270-007 Lock nut, ½ UNC 10
18 256-011 Flat washer, 1/2 4
19 255-020 Lock washer, 1-1/4" 1
20 257-054 Half nut, 1-1/4" UNC 2
21 C310-145 Retainer pin, 1 x 6-15/16 U.L. 1
22 250-059 Bolt, ½ x 1-1/2 UNC 1
23 302-015 Clevis pin, 1 x 2-7/8 1
24 250-111 Bolt, 3/4 x 4 UNC 1
25 C310-124 Wheel standard suspension plate 1
26 233-050 Rubber sandwich 1
27 C310-123 Wing wheel standard assembly 1
28 270-001 Lock nut, 3/4 UNC 9
29 250-112 Bolt, 3/4 x 3 UNC 8
30 271-005 Cotter pin, 3/16 x 1-1/2 1
31 273-006 Grease nipple, self tap 1
32 C310-115 Bolt access cover plate 1
33 255-013 Lock washer, 3/8 2
34 250-018 Bolt, 3/8 x 1 UNC 2
35 C320-132 Wing adjustment assembly 1
36 250-055 Bolt, ½ x 3/4 UNF 2
37 250-061 Bolt, ½ x 1-1/4 UNC 6
38 C312-157 Adjustable side mount, right 1
June 27, 2006
-6-
Page 8
WING FRAME, LEFT
June 27, 2006
-7-
Page 9
WING FRAME, LEFT
Ref. Part No. Description Qty.
1 C314-150 Wing assembly, left 1
2 752-014 Hinge pin, 15" O.A. 4
3 C310-140 Hinge spacer tube, 13-7/8" O.A. 2
5 262-011 Roll Pin, 3/8 x 1-3/4 6
6 C310-141 Hinge spacer tube, 10-3/8" O.A. 1
7 262-006 Roll pin, 3/8 x 2 5
8 256-001 Flat washer, 1 6
9 C301-140 Pin, 1 x 3-13/32" O.A. 2
10 C301-114 Floating lug 2
13 330-7030 Gearbox, CW 1
* CCW Gearbox (330-7031) is required for fixed knife, material distribution, and sod kits.
See your Schulte Dealer
14 250-201 Plow bolt, ½ x 1-1/2 UNC 3
16 C310-135 Outer wing skid, standard 1
17 270-007 Lock nut, ½ UNC 10
18 256-011 Flat washer, ½ 4
19 255-020 Lock washer, 1-1/4" 1
20 257-054 Half nut, 1-1/4" UNC 2
21 C310-145 Retainer pin, 1 x 6-15/16 U.L. 1
22 250-059 Bolt, ½ x 1-1/2 UNC 1
23 302-015 Clevis pin, 1 x 2-7/8 1
24 250-111 Bolt, 3/4 x 4 UNC 1
25 C310-124 Wheel standard suspension plate 1
26 233-050 Rubber sandwich 1
27 C310-123 Wing wheel standard assembly 1
28 270-001 Lock nut, 3/4 UNC 9
29 250-112 Bolt, 3/4 x 3 UNC 8
30 271-005 Cotter pin, 3/16 x 1-1/2 1
31 273-006 Grease nipple, self tap 1
32 C310-115 Bolt access cover plate 1
33 255-013 Lock washer, 3/8 2
34 250-018 Bolt, 3/8 x 1 UNC 2
35 C320-132 Wing adjustment assembly 2
36 250-055 Bolt, ½ x 3/4 UNF 2
37 250-061 Bolt, ½ x 1-1/4 UNC 6
38 C312-152 Adjustable skid mount, left 1
June 27, 2006
-8-
Page 10
HITCH FRAME AND CENTER WHEEL STANDARD
June 27, 2006
-9-
Page 11
HITCH FRAME AND CENTER WHEEL STANDARD
Ref. Part No. Description Qty.
1 271-005 Cotter pin, 3/16 x 1-1/2 3
2 256-001 Flat washer, 1 13
3 302-013 Clevis pin, 1 x 2-1/8 2
4 262-006 Roll pin, 3/8 x 2 3
5 C310-113 Hitch clevis 1
7 C310-118 Pivoting hitch assembly. 1
8 C310-119 Pivot hitch weld sleeve 1
9 250-060 Bolt, 1/2 x 1-3/4 UNC 3
10 256-011 Flat washer, 1/2 7
11 270-007 Lock nut, 1/2, UNC 3
12 273-006 Grease nipple, self tap 6
13 C310-117 Hitch frame assembly 1
14 C310-142 Retaining pin, 1 x 3-15/16 U.L. 2
16 C310-131 Lift rod, 101" O.A. 2
17 302-015 Clevis pin, 1 x 2-7/8 1
18 229-007 Compression spring, 1/2” 2
19 250-111 Bolt, 3/4 x 4 UNC 1
20 C310-125 Suspension top plate 1
21 270-001 Lock nut, 3/4 UNC 5
22 CS01-130 Leveling rod lug 2
23 257-008 Nut, 1 UNC 2
24 257-006 Half nut, 1 UNC 2
25 302-012 Clevis pin, 1 x 1-15/16 2
28 C310-108 Center section wheel standard 1
29 250-112 Bolt, 3/4 x 3 UNC 4
30 CS01-134 Retaining pin, 1 x 4-5/8 U.L. 1
31 C502-183 PTO storage support 1
32 302-034 Bent hitch pin 1
33 271-053 #10 hitch pin clip 1
June 27, 2006
-10-
Page 12
10' SKIRT ASSEMBLY
Ref. Part No. Description Qty.
1 250-060 Bolt, 1/2" x 1-3/4" UNC 2
2 250-059 Bolt, 1/2" x 1-1/2" UNC 2
3 256-011 Flat washer, 1/2" 9
4 C311-105 Chain guard, single 1
C311-106 Chain guard, double 1
5 250-145 Bolt, 1" x 4" UNC 2
7 270-007 Lock nut, 1/2" UNC 9
8 C311-102 Hinge pin, 29 1/8" O.A. 1
9 270-020 Lock nut, 1" UNC 4
10 C311-101 Skirt assembly, 10' 1
11 C311-103 Hinge pin, 5" O.A. 1
12 C302-104 Counter weight 3
13 256-001 Flat washer, 1" 4
14 250-129 Bolt, 1" x 6" UNC 2
15 250-201 Plow bolt, 1/2" x 1-1/2" UNC 5
16 C302-106 Skirt skid 1
17 270-017 Lock nut, 3/8" UNC 3
18 225-106 Chain, 5/16" proof coil, 6 links 3
225-111 Chain, 5/16" proof coil, 11 links 3
19 250-085 Bolt, 5/8" x 4" UNC 4
20 256-017 Flat washer, 3/8" 3
21 256-006 Flat washer, 5/8" 4
22 250-020 Bolt, 3/8" x 1-1/2" UNC 3
23 270-004 Lock nut, 5/8" UNC 4
June 27, 2006
-11-
Page 13
HITCH JACK, 15" SIDE WIND (232-800)
Ref. Part No. Description Qty.
1 232-621 Outer Tube and Mount 1
2 232-622 Inner Tube/ S&N Assembly 1
10 232-623 Crank, Handle 1
11 232-624 Cover 1
12 232-625 Bolt,1/4-20 x 3.12" Carriage 2
13 232-626 Locknut, 1/4" 2
14 232-627 Pull Pin Assembly 1
16 232-628 Grease Fitting 1
20 232-630 Repair Kit, c/w Ref # 3 to 9 1
NOTE: THIS JACK WILL REPLACE JACK 232-600
June 27, 2006
-12-
Page 14
HUB, AXLES & TIRES
When attaching the wheels to the hub, be sure the lock washer is installed agianst the wheel. To
reduce the possibility of the laminations separating, the laminated tires should be installed with
the laminations oriented as shown above.
June 27, 2006
-13-
Page 15
HUB, AXLES & TIRES
Ref. Part No. Description Qty.
1 208-018 Spindle, c/w #9, 15, 16, double end 1
1 208-019 Spindle, c/w #9, 15, 16, single end 1
2 207-026 Seal 1
3 207-019 Bearing 1
4 207-020 Race 1
5 273-006 Grease nipple, self-tap 1
6 205-007 Hub, c/w outer races 1
7 207-025 Race 1
8 207-024 Bearing 1
9 271-005 Cotter pin, 3/16 x 1-1/2 1
10 201-005 Wheel, 15 x 5 KB, 5 bolt, For 7.00 Tire 1
201-010 Wheel, 15 x 8 x 5, For 9.5L Tire 1
11 211-002 Valve stem 1
12 210-167 Tire, 7.00 x 15, 8 ply 1
210-157 Tire, 9.5L x 15 1
13 207-0281 Wheel bolt, 1/2-20 UNF x 1" wide shoulder 5
14 207-027 Dust cap 1
15 209-017 Castle nut, 3/4 - 16 UNF 1
17 250-018 Bolt, 3/8 x 1 UNC 5
18 210-003 Tire, solid laminated, complete 1
19 255-013 Lock washer, 3/8" 5
20 257-032 Nut, 3/8 UNC 5
21 201-008 Wheel half, 6 x 9, 5 bolt 2
22 210-004 Tire, solid laminated, 6 x 9 1
23 206-009 Hub, includes #2-8 & 14 1
23 207-055 Bearing Kit, includes #2, 3, 4, 7, 8, 14, 16 1
24 210-162 Aircraft tire 22 x 5.5 x 10 complete 1
211-010 Tube & liner for #210-162
25 255-009 Lock washer, 1/2 5
26 250-0612 Bolt, 1/2 x 1-1/4 UNF Gr. 5 5
June 27, 2006
-14-
Page 16
DRIVELINE SHIELDING
June 27, 2006
-15-
Page 17
DRIVELINE SHIELDING
Ref. Part No. Description Qty.
1 C314-203 Center section shield assembly CE 1
3 251-008 Bolt, M8 x 20mm 15
4 255-015 Lock washer, 5/16" 15
5 256-020 Flat washer, 5/16" 15
6 C314-202 Splitter shield mount 1
11 341-6235 Plastic shield 2
12 C314-204 Center gearbox pivot shield mount 1
13 341-600 Plastic shaft cover for splitter, 10' units 1
14 250-006 Bolt, 5/16" x 3/4" UNC, 10' units 2
15 271-008 Cotter pin, 1/8" x 1" 2
16 C301-203 Shield hinge pin 1
25 251-151 Machine Screw #10 x .75" Round Head 2
26 270-028 Locknut, 10-24 Nylock 2
27 C314-205 Spacer CE Shield 1
28 227-001 Latch 1
29 227-002 Euro Lock Key, 10 Ga Stainless Steel 1
30 271-013 Cotter Pin, 1/16" x 3/4" long (Not for CE) 1
June 27, 2006
-16-
Page 18
CHAIN GUARDS
June 27, 2006
-17-
Page 19
CHAIN GUARDS
C310-550 Double Chain Guard Kit, S150
Ref. Part No. Description Qty.
1 C310-555 Chain guard double, wing front 4
2 C310-552 Chain guard double, center front outer 2
3 C310-551 Chain guard double, center front middle 1
4 C310-554 Chain guard double, center rear 2
5 C310-557 Chain guard double, wing rear 4
6 C310-558 Chain guard double, wing rear outer 2
7 250-026 Bolt, 3/8" x 2-1/2" UNC 2
8 256-017 Flat washer, 3/8" 4
9 270-017 Lock nut, 3/8" UNC 2
10 225-109 Chain, 5/16" proof coil, 9 links 4
11 250-050 Bolt, 1/2" x 3-1/2" UNC 12
12 250-061 Bolt, 1/2" x 1-1/4" UNC 21
13 256-011 Flat washer, 1/2" 63
14 270-007 Lock nut, 1/2" UNC 51
15 250-059 Bolt, 1/2" x 1-1/2" 18
C310-520 Cable Kit for Double Chains, S150
Ref. Part No. Description Qty.
17 221-413 Cable, 73" 2
18 221-415 Cable, 26-3/4" 2
19 221-416 Cable, 22" 1
20 221-414 Cable, 75-1/4" 2
21 221-417 Cable, 62" 1
22 222-003 Cable clamp, 1/8" 16
June 27, 2006
-18-
Page 20
BLADE CARRIERS
June 27, 2006
-19-
Page 21
BLADE CARRIERS
Ref. Part No. Description Qty.
1 C303-222 Blade carrier, center, complete 1
2 C303-220 Blade carrier, wing, complete 2
3 520-1076 Pan only, center 1
4 520-1075 Pan only, wing 2
6 586-535 Pan reinforcements, center 4
7 251-020 Pentagon bushing, blade bolt 6
8 257-003 Locknut, 1-1/8 - 12, UNF 6
9 401-026 Blade,1/2 x 4 x 25, CW, Super Suction 2
10 401-027 Blade,1/2 x 4 x 25, CCW, Super Suction 2
11 401-032 Blade, 1/2 x 4 x 28, CW, Super Suction 2
13 251-018 Blade bolt, 1-1/8 - 12 UNF, 1/2" 6
251-201 Blade bolt & nut, 1/2" 6
.
June 27, 2006
-20-
Page 22
WING WINCH KIT (C312-300)
Ref. Part No. Description Qty.
1 450-050 Winch, 1600 lb., 5.1:1 ratio 1
2 250-019 Bolt, 3/8 x 1-1/4 UNC 3
3 256-017 Flat washer, 3/8 3
4 158-03 Cable, 135", 7/32 dia. 1/4 loop end 1
5 270-017 Lock nut, 3/8 UNC 5
6 C310-302 Winch lift stand 1
7 C312-302 Winch lift lug, right 1
8 C312-301 Winch lift lug, left 1
9 C301-303 Backing plate 1
10 250-061 Bolt, ½ x 1-1/4 UNC 4
11 270-007 Lock nut, ½ UNC 4
12 250-018 Bolt, 3/8 x 1 UNC 2
13 450-104 Winch cable keeper, hardware included 1
June 27, 2006
-21-
Page 23
WING LIFT CIRCUIT, SINGLE ACTING
June 27, 2006
C310-820 Single Acting Wing Cylinder Kit
Includes Ref # 2 only.
Ref. Part No. Description Qty.
1 100-3701 Cyl. 3 X 12 ORB 2
2 108-056 Breather, filter 3/4- 16 ORB 2
3 108-043 Elbow, 3/4" ORB male X JIC male 2
4 111-185 Hose assembly, 3/8 SW, 183" long 2
5 C000-005 Restrictor 2
8 302-015 Clevis pin, 1 x 2-7/8 UL 2
9 256-001 Flat washer, 1 x 2 2
10 271-005 Cotter pin, 3/16 x 1-1/2 2
-22-
Page 24
WING LIFT CYLINDER, MONARCH (100-3701)
June 27, 2006
Ref. Part No. Description Qty.
1 101-150 Casing, 3" x 12" 1
2 101-151 Cylinder Head 1
3 101-152 Piston 1
4 101-153 Rod 1
25 101-243 Lock Nut, 1" 1
41 101-025W Seal Kit, Includes # 10, 11, 13-15, 40 1
-23-
Page 25
PHASING CIRCUIT
Ref. Part No. Description Qty.
1 111-101 Hose assembly, 3/8 x 191" long 1
2 100-3671 Cylinder phasing, 3-1/2 x 5 1
3 111-188 Hose assembly, 3/8 x 84" long 1
4 C000-001 Hose clamp, metal 4
7 108-043 Elbow, 3/4 ORB male x JIC male 5
8 100-3681 Cylinder phasing, 3-1/4 x 5 1
9 111-186 Hose assembly, 3/8 x 171" long 1
10 100-3691 Cyl. phasing, 3 x 5 1
11 111-184 Hose assembly, 3/8 x 269" long 1
13 271-005 Cotter pin, 3/16 x 1-1/2 6
14 302-015 Clevis pin, 1 x 2-7/8 U.L. 6
17 250-023 Bolt, 3/8 x 1-3/4 UNC 1
18 256-017 Flat washer, 3/8 3
19 270-017 Locknut, 3/8 UNC 3
20 108-044 Elbow, 45
0
ORB x JIC 1
21 101-020 Depth stop 3
22 C000-005 Restrictor 1
23 262-006 Roll pin, 3/8" x 2 1
24 C502-193 Center section cylinder pin 1
25 C502-194 Cylinder pin sleeve 1
26 256-001 Washer, 1" 5
June 27, 2006
-24-
Page 26
PHASING CYLINDERS, MONARCH
3" 3-1/4" 3-1/2"
Ref. Part No. Part No. Part No. Description Qty.
100-3691 100-3681 100-3671 Phasing Cylinder
1 101-145 101-146 101-147 Casing 1
2 101-137 101-138 101-139 Cylinder Head 1
3 101-082 101-083 101-084 Piston 1
4 101-148 101-148 101-148 Rod 1
5 257-055 257-055 257-055 Jam nut, 1-1/4" UNF 1
17 101-021 101-021 101-021 Rod Clevis 1
18 250-023 250-023 250-023 Bolt, 3/8" x1-3/4" UNC, Gr 5 1
20 270-017 270-017 270-017 Lock Nut, 3/8" UNC 1
21 101-020 101-020 101-020 Stroke Control Assembly 1
25 101-243 101-243 101-243 Lock Nut, 1" 1
41 101-065 101-066 101-067 Seal Kit, Incl #10,11,13-15,40 1
June 27, 2006
-25-
Page 27
SPOOL VALVE KIT, S150 (C301-805)
Ref. Part No. Description Qty.
1 108-044 Elbow, 3/4 ORB x 3/4 JIC 6
2 108-068 Reducer, 3/4 ORB x ½ NPTF 1
3 108-031 Elbow, 3/4 - 16 JIC 1
4 108-043 Elbow, 3/4 ORB x 3/4 JIC 3
5 111-204 Hose assembly, 3/8 x 226" long 1
6 111-205 Hose assembly, 3/8 x 329" long 1
7 111-206 Hose assembly, 3/8 x 243" long 4
8 111-207 Hose assembly, ½ x 60" long 1
9 111-237 Hose assembly, ½ x 72" long 1
10 127-202 Valve, 3 spool 1
11 108-0071 Brass restrictor 3
June 27, 2006
-26-
Page 28
June 27, 2006
-27-
Page 29
SPOOL VALVE KIT, S100 (C302-805)
Ref. Part No. Description Qty.
1 108-003 Elbow, 1/2 NPT x 3/4 JIC 5
2 108-018 Reducer, 3/4 NPTM x ½ NPTF 2
3 108-031 Elbow, 3/4 - 16 JIC 1
4 108-043 Elbow, 3/4 ORB x 3/4 JIC 2
5 111-204 Hose assembly, 3/8 x 226" long 1
6 111-205 Hose assembly, 3/8 x 329" long 1
7 111-206 Hose assembly, 3/8 x 243" long 2
8 111-207 Hose assembly, ½ x 60" long 1
9 111-237 Hose assembly, ½ x 72" long 1
10 127-201 Valve, 2 spool 1
11 108-0071 Brass restrictor 2
June 27, 2006
-28-
Page 30
TRACTOR UNIVERSAL JOINT W/ 80o C.V., SIZE 8 (340-850)
June 27, 2006
-29-
Page 31
TRACTOR UNIVERSAL JOINT W/ 80o C.V., SIZE 8 (340-850)
Location: 540 RPM units
Ref. Part No. Description Qty.
1 341-80046 Yoke, 1-3/8 z6 1
2 341-80047 Cross Kit 2
5 341-80048 Yoke, Outer Tube 1
6 341-80045 Central Body 1
8 341-80074 Flexible Pin 1
12 341-80055 Outer Cardan Tube 1
13 341-80056 Inner Cardan Tube 1
16 341-80007 Flexible Pin 1
17 341-80008 Yoke, Inner Tube 1
21 341-80070 Yoke, 1-3/4 z20 1
22 341-80002 Cross Kit 1
23 341-8086 Grease Fitting, Short 2
25 341-80049 Bell Assembly 1
26 341-60039 Shield Bearing, Outer 1
27 341-80050 Ring 1
28 341-60020 Screw 12
29 341-80057 Outer Bell & Tube 1
30 341-80058 Inner Bell & Tube 1
31 341-80059 Shield 1
32 341-60014 Shield Bearing, Inner 1
34 341-80069 Washer 6
51 341-8095 Ball Collar Kit 1
61 341-802 Tapered Pin Kit 1
93 341-80061 Tractor Half Assembly w/ Shields, 1-3/8 z6 1
94 341-80062 Implement Half Assembly w/Shields 1
97 341-80067 Complete Shield Set 1
June 27, 2006
-30-
Page 32
'5,9(/,1(
94
22
16
13
23
93
6
2
1
51
8
2
12
5
28
28
34
29
40
26
25
27
61
21
17
28
31
32
40
30
97
&3 3DJH31
$ODPR *URXS ,QF
Page 33
'5,9(/,1(
127( 530 &9 7UDFWRU $VVHPEO\
'HVFULSWLRQ4W\3DUW 1R5HI
<RNH ]
&URVV .LW
<RNH 2XWHU 7XEH
&HQWUDO %RG\
)OH[LEOH 3LQ
2XWHU &DUGDQ 7XEH
,QQHU &DUGDQ 7XEH
)OH[LEOH 3LQ
<RNH ,QQHU 7XEH
<RNH ]
&URVV .LW
*UHDVH )LWWLQJ 6KRUW
%HOO $VVHPEO\
6KLHOG %HDULQJ 2XWHU
5LQJ
6FUHZ
2XWHU %HOO 7XEH
,QQHU %HOO 7XEH
6KLHOG
6KLHOG %HDULQJ ,QQHU
:DVKHU
%DOO &ROODU .LW
7DSHUHG 3LQ .LW
7UDFWRU +DOI $VVHPEO\ Z 6KLHOGV ]
,PSOHPHQW +DOI $VVHPEO\ Z6KLHOGV
&RPSOHWH 6KLHOG 6HW
&RPSOHWH 'ULYHOLQH 6)76 ZGHJ &9 530
&3 3DJH32
$ODPR *URXS ,QF
Page 34
WING UNIVERSAL JOINT, SIZE 6 (340-6013)
June 27, 2006
-33-
Page 35
WING UNIVERSAL JOINT, SIZE 6 (340-6013)
Location: 540 & 1000 RPM units
Ref. Part No. Description Qty.
1 341-805 Yoke 1
2 341-605A Cross Journal Assembly 2
4 341-653 Grease Zerk 2
5 341-622 Yoke, Outer 1
11 341-621 Flexible Pin 1
12 341-6285 Outer Cardan Tube 1
13 341-6286 Inner Cardan Tube 1
14 341-616 Flexible Pin 1
21 341-617 Yoke, Inner 1
30 341-6324 Slip Clutch, FT42, 1200Nm 1
31 341-610 Outer Shield Bearing 1
32 341-0680 Outer Cone 1
33 341-6287 Outer Tube 1
34 341-6288 Inner Tube 1
35 341-660 Inner Cone 1
36 341-615 Inner Shield Bearing 1
39 341-619 Greasing Collar 1
51 341-802 Tapered Pin 1
93 341-6282 Outer Half Shaft w/ Shields 1
94 341-6283 Inner Half Shaft w/ Shields and Clutch 1
97 341-6284 Complete Shield Set 1
June 27, 2006
-34-
Page 36
CENTER UNIVERSAL JOINT, SIZE 6
340-6153 540 RPM units
340-6163 1000 RPM units
Ref. Part No. Description Qty.
1 341-805 Yoke 1
2 341-605A Cross Journal Assembly 2
4 341-653 Grease Zerk 2
5 341-606 Yoke, Splined 2
11 341-608 Flexible Pin 1
12 341-6073 Splined Shaft, 120 mm 1
30 341-6322 Slip Clutch, FT42, 1450 Nm, 540 RPM 1
or 341-6323 Slip Clutch, FT32, 1000 Nm, 1000 RPM 1
51 341-802 Tapered Pin 1
June 27, 2006
-35-
Page 37
SLIP CLUTCH (341-6322, 341-6323)
341-6322 Bondioli FT42
Location: Center Drivelines, 540 RPM units
Ref. Part No. Description Qty.
71 341-6014 Bolt & Nut 8
72 341-6312 Clutch Plate 1
73 341-630 Bushing 1
74 341-6247 Lining 2
75 341-6248 Thrust Plate 1
77 341-6280 Hub 1
78 341-802 Tapered Pin & Nut 1
85 341-6318 Spring 1
88 341-6234 Spacer 1
341-6323 Bondioli FT32
Location: Center Drivelines, 1000 RPM units
Ref. Part No. Description Qty.
71 341-6014 Bolt & Nut 8
72 341-6316 Clutch Plate 1
73 341-630 Bushing 1
74 341-6228 Lining 2
75 341-6208 Thrust Plate 1
77 341-6281 Hub 1
78 341-802 Tapered Pin & Nut 1
85 341-6317 Spring 1
88 341-6234 Spacer 1
June 27, 2006
-36-
Page 38
June 27, 2006
-37-
Page 39
SLIP CLUTCH (341-6324)
341-6324 Bondioli FT42
Location: Wing Drivelines, 540 and 1000 RPM units
Ref. Part No. Description Qty.
71 341-6014 Bolt & Nut 8
72 341-6312 Clutch Plate 1
73 341-630 Bushing 1
74 341-6247 Lining 2
75 341-6248 Thrust Plate 1
77 341-6280 Hub 1
78 341-802 Tapered Pin & Nut 1
85 341-6313 Spring 1
88 341-6251 Spacer 1
June 27, 2006
-38-
Page 40
DIVIDER GEARBOX
June 27, 2006
-39-
Page 41
DIVIDER GEARBOX
330-930 Comer #T25A (265.870), 1:1.35 ratio
Location: Center Section, 540 RPM units
330-931 Comer #T25A (265.871), 1.35:1 ratio
Location: Center Section, 1000 RPM units
Ref. Part No. Description Qty.
1 331-973 Casing 1
2 331-950 Pinion Gear, Z20, 540 RPM 2
or 331-952 Pinion Gear, Z27, 1000 RPM 2
3 331-941 Crown Gear, Z27, 540 RPM 1
or 331-943 Crown Gear, Z20, 1000 RPM 1
4 331-974 Shim Kit 2
5 331-920 Ball Bearing 2
6 331-9019 Oil Seal, 45 x 85 x 10 2
7 331-975 Input Shaft, 1-3/4 Z20 1
8 331-914 Snap Ring 2
9 331-821 Ball Bearing 2
10 331-909 Snap Ring 2
11 331-858 Oil Seal, 45 x 80 x 10 2
12 331-976 Output Shaft, 1-3/4 Z20 2
13 331-924 Shim Kit 2
14 331-922 3/8" Gas Plug 2
15 331-977 Cover 1
16 331-902 Bolt, M8 x 30, gr 8.8 6
17 331-919 Snap Ring 1
18 331-978 Sub Plug, 1/2" Gas 1
19 331-857 Ball Bearing 2
20 331-741 Shim Kit 2
21 331-979 Snap Ring 2
251 331-928 Oil Filler Vent Plug, 1/2" Gas 1
June 27, 2006
-40-
Page 42
CW GEARBOX, WING (330-7030)
June 27, 2006
-41-
Page 43
CW GEARBOX, WING (330-7030)
330-7030 Comer #LF227J (227.009) 1:1.35 ratio, 540 & 1000 RPM
Ref. Part No. Description Qty.
1 331-7135 Casing 1
2 331-7139 Crown Gear, Z23 1
3 331-564 Tapered Roller Bearing 2
4 331-974 Shim Kit 2
5 331-914 Snap Ring 2
6 331-559 Oil Cap 1
7 331-7136 Input Shaft, 1-3/4" Z20 1
8 331-9019 Oil Seal 1
9 331-7137 Cover 1
10 331-5012 3/8" Gas Solid Plug 1
11 250-0081 Bolt, M8 x 25 4
12 331-7140 Pinion Gear Z17 1
13 331-7124 Snap Ring 1
14 331-7015 Shim 1
15 331-7012 Tapered Roller Bearing 2
16 331-7125 Shim Kit 1
17 331-7138 Output Shaft 1
18 331-7007 Castle Nut 1
19 331-7117 Cotter Pin 1
20 331-7017A Oil Filler Level Vent Plug, 4-1/2" UL 1
21 331-813 Castle Nut 1
22 331-7011 Oil Seal 1
23 331-7010 Sealing Lid 1
24 331-7028 Hub 1
25 331-814 Bevel Washer 1
26 331-7020 Flat Washer 1
251 331-812 Cotter Pin 1
June 27, 2006
-42-
Page 44
CCW GEARBOX, WING (330-7031)
June 27, 2006
-43-
Page 45
CCW GEARBOX, WING (330-7031)
330-7031 Comer #LF227J (227.010) 1:1.35 ratio, 540 & 1000 RPM
Ref. Part No. Description Qty.
1 331-7135 Casing 1
2 331-7141 Crown Gear, Z23 1
3 331-564 Tapered Roller Bearing 2
4 331-974 Shim Kit 2
5 331-914 Snap Ring 2
6 331-559 Oil Cap 1
7 331-7136 Input Shaft, 1-3/4" Z20 1
8 331-9019 Oil Seal 1
9 331-7137 Cover 1
10 331-5012 3/8" Gas Solid Plug 1
11 250-0081 Bolt, M8 x 25 4
12 331-7142 Pinion Gear Z17 1
13 331-7124 Snap Ring 1
14 331-7015 Shim 1
15 331-7012 Tapered Roller Bearing 2
16 331-7125 Shim Kit 1
17 331-7138 Output Shaft 1
18 331-7007 Castle Nut 1
19 331-7117 Cotter Pin 1
20 331-7017A Oil Filler Level Vent Plug, 4-1/2" UL 1
21 331-813 Castle Nut 1
22 331-7011 Oil Seal 1
23 331-7010 Sealing Lid 1
24 331-7028 Hub 1
25 331-814 Bevel Washer 1
26 331-7020 Flat Washer 1
251 331-812 Cotter Pin 1
June 27, 2006
-44-
Page 46
CW GEARBOX, CENTER, 540 RPM (330-7035)
June 27, 2006
-45-
Page 47
CW GEARBOX, CENTER, 540 RPM (330-7035)
330-7035 Comer #LF227J (227.011) 1:1.5 ratio, 540 RPM units
Ref. Part No. Description Qty.
1 331-7135 Casing 1
2 331-7143 Crown Gear, Z24 1
3 331-564 Tapered Roller Bearing 2
4 331-974 Shim Kit 2
5 331-914 Snap Ring 2
6 331-559 Oil Cap 1
7 331-7136 Input Shaft, 1-3/4" Z20 1
8 331-9019 Oil Seal 1
9 331-7137 Cover 1
10 331-5012 3/8" Gas Solid Plug 1
11 250-0081 Bolt, M8 x 25 4
12 331-7144 Pinion Gear Z16 1
13 331-7124 Snap Ring 1
14 331-7015 Shim 1
15 331-7012 Tapered Roller Bearing 2
16 331-7125 Shim Kit 1
17 331-7138 Output Shaft 1
18 331-7007 Castle Nut 1
19 331-7117 Cotter Pin 1
20 331-7017A Oil Filler Level Vent Plug, 4-1/2" UL 1
21 331-813 Castle Nut 1
22 331-7011 Oil Seal 1
23 331-7010 Sealing Lid 1
24 331-7028 Hub 1
25 331-814 Bevel Washer 1
26 331-7020 Flat Washer 1
251 331-812 Cotter Pin 1
June 27, 2006
-46-
Page 48
CW GEARBOX, CENTER, 1000 RPM (330-7036)
June 27, 2006
-47-
Page 49
CW GEARBOX, CENTER, 1000 RPM (330-7036)
330-7036 Comer #LF227J (227.012) 1.22:1 ratio, 1000 RPM units
Ref. Part No. Description Qty.
1 331-7135 Casing 1
2 331-7145 Pinion Gear, Z18 1
3 331-564 Tapered Roller Bearing 2
4 331-974 Shim Kit 2
5 331-914 Snap Ring 2
6 331-559 Oil Cap 1
7 331-7136 Input Shaft, 1-3/4" Z20 1
8 331-9019 Oil Seal 1
9 331-7137 Cover 1
10 331-5012 3/8" Gas Solid Plug 1
11 250-0081 Bolt, M8 x 25 4
12 331-7146 Crown Gear Z22 1
13 331-7124 Snap Ring 1
14 331-7015 Shim 1
15 331-7012 Tapered Roller Bearing 2
16 331-7125 Shim Kit 1
17 331-7148 Output Shaft 1
18 331-7130 Castle Nut 1
19 331-7117 Cotter Pin 1
20 331-7017A Oil Filler Level Vent Plug, 4-1/2" UL 1
21 331-813 Castle Nut 1
22 331-7011 Oil Seal 1
23 331-7010 Sealing Lid 1
24 331-7028 Hub 1
25 331-814 Bevel Washer 1
26 331-7020 Flat Washer 1
251 331-812 Cotter Pin 1
June 27, 2006
-48-
Page 50
TRANSPORT KITS
Safety Chain (S000-010)
10,100 lbs. capacity, 59" min. length
NOTE: This safety chain is intended as an auxiliary
attaching system per ASAE S338.3. The safety chain will help control the rotary cutter should it accidentally
separate from the drawbar. Do not use the safety chain for towing. Replace the entire chain if any link or
end fitting is broken, damaged or stretched.
Transport Light Kit (S000-045)
Ref. Part No. Description Qty.
1 S000-087 Transport light set, complete with harness 1
2 S000-101 Light Bracket 2
3 S000-046 Light bracket 2
4 258-110 U-bolt, 4" x 5-1/16" long x 3/8" UNC 2
5 250-006 Bolt, 5/16 x 3/4" UNC 4
6 270-020 Lock nut, 5/16" UNC 4
7 270-017 Lock nut, 3/8" UNC 4
8 256-020 Washer, 5/16" 4
Includes a 7-pin ag plug, wishbone harness and left and right hand dual lights. The lights are to be mounted
with the red and amber facing to the rear with the amber to the outside, or in a vertical installation, with the
amber on top.
June 27, 2006
-49-
Page 51
PARTS INDEX
Part Number Page Part Number Page
100-3671 ............................ 24, 25
100-3681 ............................ 24, 25
100-3691 ............................ 24, 25
100-3701 ............................ 22, 23
101-020 ............................. 24, 25
101-021 ................................ 25
101-025W ............................... 23
101-065 ................................ 25
101-066 ................................ 25
101-067 ................................ 25
101-082 ................................ 25
101-083 ................................ 25
101-084 ................................ 25
101-137 ................................ 25
101-138 ................................ 25
101-139 ................................ 25
101-145 ................................ 25
101-146 ................................ 25
101-147 ................................ 25
101-148 ................................ 25
101-150 ................................ 23
101-151 ................................ 23
101-152 ................................ 23
101-153 ................................ 23
101-243 ............................. 23, 25
108-003 ................................ 28
108-0071 ............................ 26, 28
108-018 ................................ 28
108-031 ............................. 26, 28
108-043 ....................... 22, 24, 26, 28
108-044 ............................. 24, 26
108-056 ................................ 22
108-068 ................................ 26
111-101 ................................ 24
111-184 ................................ 24
111-185 ................................ 22
111-186 ................................ 24
111-188 ................................ 24
111-204 ............................. 26, 28
111-205 ............................. 26, 28
111-206 ............................. 26, 28
111-207 ............................. 26, 28
111-237 ............................. 26, 28
127-201 ................................ 28
127-202 ................................ 26
13-15 ............................... 23, 25
150-32 .................................. 4
158-03 ................................. 21
201-005 ................................ 14
201-008 ................................ 14
201-010 ................................ 14
205-007 ................................
206-009 ................................ 14
207-019 ................................ 14
207-020 ................................ 14
207-024 ................................ 14
207-025 ................................ 14
207-026 ................................ 14
207-027 ................................ 14
14
207-0281 ............................... 14
207-055 ................................ 14
208-018 ................................ 14
208-019 ................................ 14
209-017 ................................ 14
210-003 ................................ 14
210-004 ................................ 14
210-157 ................................ 14
210-162 ................................ 14
210-167 ................................ 14
211-002 ................................ 14
211-010 ................................ 14
221-413 ................................ 18
221-414 ................................ 18
221-415 ................................ 18
221-416 ................................ 18
221-417 ................................ 18
222-003 ................................ 18
225-106 ................................ 11
225-109 ................................ 18
225-111 ................................ 11
227-001 ................................ 16
227-002 ................................ 16
228-012 ................................. 4
229-007 ................................ 10
232-600 ................................ 12
232-800 ................................ 12
233-050 ............................... 6, 8
250-002 ................................. 4
250-006 ............................. 16, 49
250-018 ....................... 4, 6, 8, 14, 21
250-019 .............................. 4, 21
250-020 ................................ 11
250-023 ........................... 4, 24, 25
250-026 ................................ 18
250-050 ................................ 18
250-055 ............................... 6, 8
250-059 ......................... 6, 8, 11, 18
250-060 ........................... 4, 10, 11
250-061 ......................... 6, 8, 18, 21
250-0612 ............................... 14
250-084 ................................. 4
250-085 ................................
250-090 ................................. 4
250-093 ................................. 4
250-111 .......................... 4, 6, 8, 10
250-112 .......................... 4, 6, 8, 10
250-129 ................................ 11
250-145 ................................ 11
250-201 ............................ 6, 8, 11
251-008 ................................ 16
251-018 ................................ 20
251-020 ................................ 20
251-151 ................................ 16
251-201 ................................ 20
255-009 ................................ 14
255-013 .......................... 4, 6, 8, 14
255-015 ................................ 16
255-020 ............................... 6, 8
11
June 27, 2006
-50-
Page 52
256-001 ................. 4, 6, 8, 10, 11, 22, 24
256-006 .............................. 4, 11
256-011 .................... 4, 6, 8, 10, 11, 18
256-017 ..................... 4, 11, 18, 21, 24
256-018 ................................. 4
256-020 ............................. 16, 49
257-003 ................................ 20
257-006 ................................ 10
257-008 ................................ 10
257-032 ................................ 14
257-054 ............................... 6, 8
257-055 ................................ 25
258-110 ................................ 49
262-005 ................................. 4
262-006 ....................... 4, 6, 8, 10, 24
262-011 ............................... 6, 8
270-001 .......................... 4, 6, 8, 10
270-004 .............................. 4, 11
270-007 ................. 4, 6, 8, 10, 11, 18, 21
270-017 ................4, 11, 18, 21, 24, 25, 49
270-020 ............................. 11, 49
270-025 ................................. 4
270-028 ................................ 16
271-005 ................... 6, 8, 10, 14, 22, 24
271-008 ................................ 16
271-013 ................................ 16
271-053 ................................ 10
273-006 ......................... 6, 8, 10, 14
280-200 ................................. 4
300-012 ................................. 4
302-012 ................................ 10
302-013 ................................ 10
302-015 ...................... 6, 8, 10, 22, 24
302-034 ................................ 10
330-7030 ........................ 6, 8, 41, 42
330-7031 ........................ 6, 8, 43, 44
330-7035 .......................... 4, 45, 46
330-7036 .......................... 4, 47, 48
330-930 .............................. 4, 40
330-931 .............................. 4, 40
331-5012 ...................... 42, 44, 46, 48
331-559 ....................... 42, 44, 46, 48
331-564 ....................... 42, 44, 46, 48
331-7007 ...................... 42, 44, 46, 48
331-7010 ...................... 42, 44, 46, 48
331-7011 ...................... 42, 44, 46, 48
331-7012 ...................... 42, 44, 46, 48
331-7015 ...................... 42, 44, 46, 48
331-7017A ..................... 42, 44, 46, 48
331-7020 ...................... 42, 44, 46, 48
331-7028 ......................
42, 44, 46, 48
331-7117 ...................... 42, 44, 46, 48
331-7124 ...................... 42, 44, 46, 48
331-7125 ...................... 42, 44, 46, 48
331-7135 ...................... 42, 44, 46, 48
331-7136 ...................... 42, 44, 46, 48
331-7137 ...................... 42, 44, 46, 48
331-7138 ......................... 42, 44, 46
331-7139 ............................... 42
331-7140 ............................... 42
331-7141 ............................... 44
331-7142 ............................... 44
331-7143 ............................... 46
331-7144 ............................... 46
331-7145 ............................... 48
331-7146 ............................... 48
331-7148 ............................... 48
331-741 ................................ 40
331-812 ....................... 42, 44, 46, 48
331-813 ....................... 42, 44, 46, 48
331-814 ....................... 42, 44, 46, 48
331-821 ................................ 40
331-857 ................................ 40
331-858 ................................ 40
331-9019 ................... 40, 42, 44, 46, 48
331-902 ................................ 40
331-909 ................................ 40
331-914 .................... 40, 42, 44, 46, 48
331-919 ................................ 40
331-920 ................................ 40
331-922 ................................ 40
331-924 ................................ 40
331-928 ................................ 40
331-940 ................................ 40
331-941 ................................ 40
331-942 ................................ 40
331-943 ................................ 40
331-973 ................................ 40
331-974 .................... 40, 42, 44, 46, 48
331-975 ................................ 40
331-976 ................................ 40
331-977 ................................ 40
331-978 ................................ 40
331-979 ................................ 40
340-6013 ............................ 33, 34
340-6153 ............................... 35
340-6163 ............................... 35
340-645 ............................. 31, 32
340-850 ............................. 29, 30
341-0680 ............................... 34
341-600 ................................ 16
341-60001 ...............................
32
341-60002 ............................... 32
341-60003 ............................... 32
341-60004 ............................... 32
341-60005 ............................... 32
341-60006 ............................... 32
341-60007 ............................... 32
341-60008 ............................... 32
341-60009 ............................... 32
341-60010 ............................... 32
341-60011 ............................... 32
341-60012 ............................... 32
341-60013 ............................... 32
341-60014 ............................ 30, 32
341-60015 ............................... 32
341-60016 ............................... 32
341-60017 ............................... 32
341-60018 ............................... 32
341-60019 ............................... 32
341-60020 ............................ 30, 32
341-60021 ............................... 32
341-60022 ............................... 32
341-60023 ............................... 32
341-60024 ............................... 32
341-60025 ............................... 32
June 27, 2006
-51-
Page 53
341-60026 ............................... 32
341-60028 ............................... 32
341-60029 ............................... 32
341-60039 ............................... 30
341-6014 ............................ 36, 38
341-605A ............................ 34, 35
341-606 ................................ 35
341-6073 ............................... 35
341-608 ................................ 35
341-610 ................................ 34
341-615 ................................ 34
341-616 ............................. 32, 34
341-617 ................................ 34
341-619 ................................ 34
341-6208 ............................... 36
341-621 ............................. 32, 34
341-622 ................................ 34
341-6228 ............................... 36
341-6234 ............................... 36
341-6235 ............................... 16
341-6247 ............................ 36, 38
341-6248 ............................ 36, 38
341-6251 ............................... 38
341-6280 ............................ 36, 38
341-6281 ............................... 36
341-6282 ............................... 34
341-6283 ............................... 34
341-6284 ............................... 34
341-6285 ............................... 34
341-6286 ............................... 34
341-6287 ............................... 34
341-6288 ............................... 34
341-630 ............................. 36, 38
341-6312 ............................ 36, 38
341-6313 ............................... 38
341-6316 ............................... 36
341-6317 ............................... 36
341-6318 ............................... 36
341-6322 ............................ 35, 36
341-6323 ............................ 35, 36
341-6324 ............................ 34, 38
341-653 ............................. 34, 35
341-660 ................................ 34
341-80002 ............................... 30
341-80007 ............................... 30
341-80008 ............................... 30
341-80020 ............................... 32
341-80045 ............................... 30
341-80046 ............................... 30
341-80047 ............................... 30
341-80048 ...............................
30
341-80049 ............................... 30
341-80050 ............................... 30
341-80055 ............................... 30
341-80056 ............................... 30
341-80057 ............................... 30
341-80058 ............................... 30
341-80059 ............................... 30
341-80061 ............................... 30
341-80062 ............................... 30
341-80067 ............................... 30
341-80069 ............................... 30
341-80070 ............................... 30
341-80074 ............................... 30
341-802 ........................ 30, 34-36, 38
341-805 ............................. 34, 35
341-8086 ............................... 30
341-8095 ............................... 30
401-026 ................................ 20
401-027 ................................ 20
401-032 ................................ 20
450-050 ................................ 21
450-104 ................................ 21
520-1075 ............................... 20
520-1076 ............................... 20
586-535 ................................ 20
752-014 ............................... 6, 8
C000-001 ............................. 4, 24
C000-005 ............................ 22, 24
C301-113 ................................ 4
C301-114 .............................. 6, 8
C301-118 ................................ 4
C301-140 .............................. 6, 8
C301-203 ............................... 16
C301-303 ............................... 21
C301-805 ............................... 26
C302-104 ............................... 11
C302-106 ............................... 11
C302-805 ............................... 28
C303-220 ............................... 20
C303-222 ............................... 20
C310-105 ................................ 4
C310-108 ............................... 10
C310-112 ................................ 4
C310-113 ............................... 10
C310-115 ............................ 4, 6, 8
C310-117 ............................... 10
C310-118 ............................... 10
C310-119 ............................... 10
C310-120 ................................ 4
C310-123 .............................. 6, 8
C310-124 ..............................
6, 8
C310-125 ............................... 10
C310-127 ................................ 4
C310-131 ............................... 10
C310-135 .............................. 6, 8
C310-140 .............................. 6, 8
C310-141 .............................. 6, 8
C310-142 ............................... 10
C310-143 ................................ 4
C310-144 ................................ 4
C310-145 .............................. 6, 8
C310-302 ............................... 21
C310-520 ............................... 18
C310-550 ............................... 18
C310-551 ............................... 18
C310-552 ............................... 18
C310-554 ............................... 18
C310-555 ............................... 18
C310-557 ............................... 18
C310-558 ............................... 18
C310-820 ............................... 22
C311-101 ............................... 11
C311-102 ............................... 11
C311-103 ............................... 11
C311-105 ............................... 11
June 27, 2006
-52-
Page 54
C311-106 ............................... 11
C312-119 ................................ 4
C312-152 ................................ 8
C312-157 ................................ 6
C312-300 ............................... 21
C312-301 ............................... 21
C312-302 ............................... 21
C314-101 ................................ 4
C314-150 ................................ 8
C314-155 ................................ 6
C314-202 ............................... 16
C314-203 ............................... 16
C314-204 ............................... 16
C314-205 ............................... 16
C320-132 .............................. 6, 8
C502-183 ............................... 10
C502-193 ............................... 24
C502-194 ............................... 24
CS01-130 ............................... 10
CS01-134 ............................... 10
S000-010 ............................... 49
S000-045 ............................... 49
S000-046 ............................... 49
S000-087 ............................... 49
S000-101 ............................... 49
June 27, 2006
-53-
Page 55
Page 56
C314TG010P
Printed in Canada
Loading...