PWO-A
Replacing and Purchasing
Consumable Parts
The gasket and lid are consumable parts. Check once
a year for damage/deterioration. If heavily stained or
loose, replace them.
For replacement parts, contact customer service or
the shop where purchase was made.
For the purpose of performance improvement, designs, specifications and parts shown in this publication are subject to
change without notice.
Before Contacting Customer
Service
The utmost measures have been taken to ensure
the quality of this product. Should you have any
problems or questions, however, contact your
dealer and provide the following information:
1. Product name
2. Model Number
Feel free to send any questions or comments about
this product to the shop where you purchased it.
3. Description of issue
(as detailed as possible)
4. Purchase date
MODEL
PWO-A
For household use
Stainless Steel Handy Jug
Push lever type
Specifications
Model No.
Capacity
Heat retention (10 hours)
Cold retention (10 hours)
Size
Weight
Heat retention has been calculated under the condition of adding hot water at 95°C±1°C / 203°F±2°F and
leaving it in a room temperature of 20°C±2°C / 68°F±4°F for 10 hours.
Cold retention has been calculated under the condition of adding cold water at 4°C ±1°C / 39°F±2°F and
leaving it in a room temperature of 20°C±2°C / 68°F±4°F for 10 hours.
Capacity is the actual volume of water that can be stored into the product when the spout is closed. This is
not the “Maximum level” volume described in “Safety Precautions”.
PW O - A12 0
1.2 L / 40.6 oz
Greater than 66°C / 150°F
Less than 10°C / 50°F
W 13.0 x D 16.6 x H 20.8 cm
W 5.12 x D 6.54 x H 8.19 inch
0.69 kg / 1.52 lbs
Head Office: 3-1 Hayami-cho, Kadoma City, Osaka 571-8571, Japan
PW O - A160
1.6 L / 54.1 oz
Greater than 71°C / 159°F
Less than 9°C / 49°F
W 13.0 x D 16.6 x H 24.5 cm
W 5.12 x D 6.54 x H 9.65 inch
0.76 kg / 1.68 lbs
PWO-A200
2.0 L / 67.6 oz
Greater than 74°C / 165°F
Less than 8°C / 47°F
W 13.0 x D 16.6 x H 28.2 cm
W 5.12 x D 6.54 x H 11.10 inch
0.84 kg / 1.85 lbs
Approximate value
TIGER CORPORATION HONG KONG LIMITED
Rm. 1006B, 10/FI., Join-in Hang Sing Centre, 71 - 75 Container Port Road,
Kwai Chung, N.T.
Tel: (852) 2418-0912 Fax: (852) 2418-0911
URL : http://tiger-corporation.hk/
Instructions
Thank you for purchasing a “TIGER”
Stainless Steel Handy Jug.
Please read the instructions thoroughly
before use.
Keep these instructions for future reference.
Lower part of
inner stopper
Brim
Handle
Main body
Top gasket
Middle gasket
Bottom gasket
Spout
Push lever
The stopper opens
when you press the
push lever.
Open/close lever
Upper part of
inner stopper
Inner
stopper
TIGER CORPORATION U.S.A.
1815 W 205th Street, Unit 106, Torrance, CA 90501
Tel: 1-866-55-TIGER (84437)
Email: support@japantigercorp.com
URL : https://tiger-corporation-us.com/
Please make sure that all parts are present before use.
Safety Precautions
All safety instructions described below are intended to protect the user and other individuals from physical harm
and household damage.
Safety instructions are classified and described according to the level of harm and damage caused by improper
use, as shown below.
This symbol indicates there is
Warning Caution
a possibility of death or serious
injury.
Be sure to follow all instructions.
This symbol indicates there is a
possibility of injury or damage to
property.
Description of Symbols
This symbol indicates a prohibited action.
This symbol indicates an action that must be
taken or an instruction that must be followed.
Warning
Keep out of reach of children. Do not let
children play with the product.
There is a risk of burns
or injuries.
Caution
Do not tilt or place this product on its
side when it is full.
The contents may spill and may cause burns.
Do not shake, knock over, drop, or subject
this product to strong collisions.
The contents may spill and cause burns, or the
product may be damaged.
Do not use this product near stoves or
open flames, or in direct sunlight.
There is a risk of burns, deformation or
discoloring of the product.
Do not use the product in a moving
vehicle.
The contents may spill and may result in burns or
stain clothing/vehicle interior.
Do not use the product if its ability to
retain heat (cold) declines.
Hot beverages can make the product very hot,
potentially causing burns.
Do not fill the product above the
maximum level shown below.
Overfilling the product may stiffen the push lever
or cause the contents (beverage) to spill when
closing the cap, resulting in burns.
Maximum level
(Slightly less)
Approx. 1cm
or 1/2inch
Beverage
Do not remove the sticker on the bottom of the product.
Caution
Do not use the product for any purpose
other than keeping beverages warm or
cold for drinking.
Securely close the inner stopper.
Make sure that the cap is fitted securely
before pouring beverages.
The cap may fall off, resulting in the
contents spilling and causing burns.
Do not tilt the main body suddenly when
pouring drinks.
The contents may spill out of the jug and may
lead to burns.
Do not press the push lever when the
spout is near a person’s face or when
the product is in a tilted position.
Liquid or steam may splash out of the jug,
causing burns.
Do not touch the brim or spout of the
product with a kettle spout.
The product may fall over, causing burns or
injuries to the skin, or may lead to a product
deformation.
Brim
Before removing the inner stopper,
briefly depress the push lever to release
any remaining steam.
Liquid or steam may escape from the jug,
causing burns if not vented prior to removal.
Do not put dry ice or carbonated
beverages in the product.
The air pressure inside the product may increase,
causing the stopper to become stuck or prone
to shattering. Other parts may also be damaged,
leading to injuries.
Tilted position
Do not store milk, dairy products or
certain fruit juices in the product.
The contents may decay or spoil. Long-time
spoilage can create gases that raise the air
pressure inside the product which can cause the
inner stopper to become stuck, shatter, damage
parts and increase risk of injury.
Do not store soups or beverages
containing salt in the product.
The product may decay, spoil or rust.
Do not store tea leaves or peeled fruit.
The contents may clog the spout, resulting in the
contents splattering and causing burns.
Only place beverages such as barley or black tea
in the jug after straining them sufficiently.
Do not use chlorine-based bleach.
It may result in corrosion, peeling of the coating
or the formation of holes.
Do not carry this product around in a
tilted position or with the push lever
pressed.
The contents may leak and cause burns.
Carry it in an upright and level position.
Push lever
Push lever pressed
Open/close lever held
Do not disassemble or attempt to repair
the product by yourself.
There is a risk of failure or accident.
1
2
How to Use
1
Turn the inner stopper to remove it.
When Using for the First Time
Wash the inner flask, brim, and cap.
Remove the inner stopper while
pinching the open/close lever
with fingers.
②
Open/close lever
①
Inner stopper
①
2
To keep beverages warm/cool longer, first pour a small amount of hot/cold water
into the main body and let it sit for one or two minutes.
Discard the hot/cold water after preheating/precooling.
3
Pour hot/cold beverage into the main body.
Fill the jug to the filling limit shown below, but do not
overfill it.
Brim
4
Place the inner stopper onto the jug.
Align the direction of the push lever and handle, and close the inner stopper securely.
Push lever
Inner stopper
Handle
Handle
Catch
Continue pressing firmly
until the left/right catch
fits into place and is heard
a “click” sound.
Slot
Push lever
The push lever and handle will not fit into place
unless the directions are properly aligned.
If the inner stopper is not securely inserted,
the contents may leak out.
5
Press the push lever before tilting the jug and pouring the beverage.
When the jug is full, the beverage will pour with just a slight tilt, so bring a cup close to the spout.
Push lever
Press the push lever
while the jug is in an
upright and level position.
Tilt the jug while
pressing the lever
to pour.
Maximum level
(Slightly less)
Approx. 1cm
or 1/2inch
Beverage
If adding ice, break large pieces into small pieces
before placing them into the jug.
(Do not insert large cubes of ice.)
When making tea, it is recommended pour to
* If pouring hot liquids into the pot, be
careful not to spill liquids on hands.
(Burns may result.)
hot water into the jug and use tea bags.
(When tea leaves are inserted directly, the tea may discolor over time.)
3
Main body
6
After pouring, hold the jug in an upright and level position,
and wait 2 to 3 seconds before releasing the push lever.
Main body
Do not release the push lever while the jug is tilted.
A small amount of liquid may remain in the inner
stopper and spill out while carrying the jug.
Push lever
Liquid remains in
the inner stopper.
4
Hold the jug in an
upright position,
while pressing the
push lever.
Release the
lever after 2
to 3
seconds.
How to Clean
Clean the product on the same day after every use.
Use household kitchen detergent (for washing dishes and cooking utensils).
Use a soft sponge or cloth.
Clean the product thoroughly to prevent any stains or odors.
Wipe with a damp cloth. (Do not wash.)
Wipe off with a dry cloth and allow each part to
Upper part of inner stopper
Middle gasket
dry thoroughly.
Wash each part using a sponge with diluted
detergent water or lukewarm water and then
thoroughly rinse with water.
Bottom gasket
After washing the main body, immediately use a
dry cloth to wipe off the moisture on its outer
surface.
(This may lead to water marks remaining on the
Lower part of inner
Main body
Top gasket
（Remove for washing
stopper
（Remove for washing
→
P. 6
）
→
P. 6
）
body and can lead to rust.)
Thoroughly shake off any remaining water and
dry the body.
To prevent odor
Before using or after pouring any liquids such as
teas or drinks with sugar, thoroughly clean the jug
by repeatedly rinsing with boiling water. This will
help prevent odors and keep the jug clean.
Do not soak the main body.
Do not wash (only wipe) the upper part of the inner stopper.
Do not use harsh or abrasive materials such as thinner, bleach, chemical cleaner, steel
wool and/or hard brush.
Do not place in dishwashers or dryers.
Be sure to attach the gaskets to the inner stopper.
Wash and dry each part thoroughly before storing for long periods without use.
Attachment/removal of inner stopper and gasket
Inner stopper
< Removal >
Turn the lower part to
the left.
Remove.
< Attachment >
Place the lower and upper part of the
inner stopper together as shown in the
diagram below.
Insert the
lower part.
Turn to right
click into
place.
Lower part of
inner stopper
Place the lower part of the
inner stopper so that the
air release hole is aligned
with the push lever.
If the inner stopper is not correctly
installed, there is the possibility
that liquids may leak out when the
jug is tilted, and this could cause
serious burns.
Part to insert
Upper part of inner
stopper
After attachment
Air release
hole
If dirt or stains become visible on the inside of the main body
For red rust like spots or rough areas
Such stains can be caused by minerals in water such as calcium, magnesium and iron. It is recommended
to constantly clean with citric acid that is available at supermarkets and drug stores.
(1) Dilute the citric acid (approximately 10g) in lukewarm water and pour into the main body.
(2) Wash the main body with a soft brush after a few hours and then thoroughly rinse.
(3) Dry the main body completely.
For tea or coffee stains
These stains are caused by the tannins and oils included in the beverages.
For purchase details, please refer to “Replacing and Purchasing Consumable Parts.” Back cover
If the gaskets develop an odor
Some contents may leave a residual odor on the gaskets. If this happens, place the gaskets in boiling water
for about 30 minutes to reduce the odor. If the odor remains strong, purchase replacement gaskets (sold
separately).
Top gasket
Cross-section
Check the direction
when placing the
gasket and ensure it
is fits securely into
the slot.
Middle and bottom gaskets
If the middle or bottom gaskets have
come off, attach them securely.
After attachment
Middle gasket
Bottom gasket
Top gasket
Top gasket
5
6
Loading...