Tiger JD 62-6430 User Manual

Current as of 11/10/2010

SNOW PLOW

ASSEMBLIES

JD 62-6430

PARTS LISTING WITH
MOUNTING AND OPERATING
INSTRUCTIONS

Tiger Corporation

3301 N. Louise Ave.

Sioux Falls, SD 57107

1-800-843-6849

1-605-336-7900

www.tiger-mowers.com

06011008

TO THE OWNER / OPERATOR / DEALER

All implements with moving parts are potentially hazardous. There is no substitute for a cautious,
safe-minded operator who recognizes the potential hazards and follows reasonable safety practices.
The manufacturer has designed this implement to be used with all its safety equipment properly at­tached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in this manual.

Observe the rules of safety and use common sense!

READ AND UNDERSTAND THIS MANUAL! Non–English speaking operators will need to GET
THE MANUAL TRANSLATED as needed!

W arranty Information: Read and understand the complete W arranty Statement found in this manual. Fill out the
W arranty Registration form in full and return it within 90 days. Make certain the Serial Number of the machine is
recorded on the W arranty Card, and form that you retain.

FORWARD

This manual contains information about many features of the Tiger mowing
and roadside maintenance equipment. Some of these include: Safety precautions,
Assembly instructions, Operations, Maintenance and Parts. This manual will also
assist you in the proper break-in, daily care, andtroubleshooting of your new
mower.

We recommend that you read carefully the entire manual before operating the
unit. Also, time spent in becoming fully acquainted with its performance features,
adjustments, and maintenance schedules will berepaid in a long and satisfactory
life of the equipment.

T roubleshooting - Please, before you call, help us to help you!

Please look at the equipment to observe what is happening, then:

• Classify the problem

• Hydraulic, electrical or mechanical - Read the trouble shooting section

• Tractor or Truck chassis - Contact vehicle dealer

• If unable to correct the problem yourself, contact your local Tiger Dealer after

gathering:

• Machine model _______________________

• Serial number ________________________

• Dealer name _________________________

• Detailed information about the problem including results of troubleshooting

Attention Owner / Operator / Dealer: It is your obligation to read, and understand,

the warranty information section located at the back of this manual denoting that the
purchaser understands the safety issues relating to this machine and has received
and will read a copy of this manual.

If at any time, you have a service problem with your Tiger mower, Contact
your local dealer for service and parts needed.

MANUFACTURED BY: DISTRIBUTED BY:

Tiger Corporation _____________________

3301 N. Louise Ave. _____________________
Sioux Falls, SD 57107 1-_____-_____-________
1-800-843-6849 1-_____-_____-________
1-605-336-7900
www.tiger-mowers.com

T ABLE OF CONTENTS

SAFETY SECTION_____________________________________ 1

ASSEMBLY / MOUNTING SECTION______________________ 2

OPERATION SECTION_________________________________ 3

MAINTENANCE SECTION______________________________ 4

P ARTS SECTION______________________________________ 5

WARRANTY INFORMA TION____________________________ 6

This symbol means:

CAUTION – YOUR SAFETY IS AT RISK!

When you see this symbol, read and

follow the associated instructions carefully

or personal injury or damage may result.

Tiger is a registered trademark.

SAFETY SECTION

© 2009 Alamo Group Inc.

Safety Section 1-1

SAFETY

A careful operator is the b est operator. Safety is of primary importance to the manufacturer and should be to
the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and
observing certain precautions. The first section of this manual includes a list o f Safety Messages that, if
followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety
Messages before assembling, operating or servicing this Implement. This equipment should only be operated
by those persons who have read the manual, who are responsible and trained, and who know how to do so
responsibly.

The Safety Alert Symbol combined with a Signa l Word, as se en below, is use d throughout this
manual and on decals which are attached to the equipment. The Safety Aler t Symbol means:
“ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word
are intended to warn the owner/operator of impending hazards and the degree of possible injury
faced when operating this equipment.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR
VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if no t avoided, COULD result in DE ATH
OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR
INJURY.

Identifies special instructions or procedures that, if no t strictly observed, could result in
damage to, or destruction of the machine, attachments or the environment.

NOTE: Identifies points of particular interest for more efficient and convenient operation or repair.

(SG-1)

Practice all usual and customary safe working precautions and above all---remember safety is
up to YOU

. Only YOU can prevent serious injury or death from unsafe practices.

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or
death may occur unless care is taken to follow the warnings and instructions stated in the
Safety Messages. Always use good common sense to avoid hazards.

(SG-2)

GENERAL SAFETY INSTRUCTIONS AND PRACTICES

SAFETY

Front & Mid Plow Wings Safety Section 1-2

© 2009 Alamo Group Inc.

SAFETY

Repeated or substantial breathing of hazardous dusts, including
crystalline silica, could cause fatal or serious respiratory disease including
silicosis. Concrete, masonry, many types of rock, and various other
materials contain silica sand. California lists respirable crystalline silica as
a substance known to ca use cancer. Operation of this equipment under
certain conditions may generate airborne dust particles that could contain
crystalline silica. In those conditio ns, personal protective equipment
including an appropriate respirator must be used. If excessive dust is
generated, a dust collection or suppression system should also be used
during operation.

(SG-41)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las
medidas de seguridad.

(SG-3)

Never operate the Sno w Plow until you have read and completely
understand this Manual , the Truck or Power units Operator’s
Manual, and each of the Safety Messages found in these Manuals
and those affixed to the Snow Plow, Truck, or Power units and its
components. Learn how to stop the power unit engine suddenly in
an emergency

.

Never allow inexperienced or untrained personnel
to operate the Truck or Pow er unit and Sno w Plow without
supervision. Make sure the operator has fully read and understood
the manuals prior to operation.

(SPNG-4)

In addition to the design and configuration of this Snow Plow, including Safety Signs and Safety Equipment,
hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper
training of pe rsonnel involved in the operation, transport, maintenance, and storage of the machine. Refer
also to Safety Messages and operation instruction in each of the appropriate sections of the Truck or Power
unit Manuals. Pay close attention to the Safety Signs affixed to the Snow Plow.

(SNPG-5)

PARTS IN FORM ATION

HENKE Snow Plows use ba lanced and matched system components for plows, carriers, and other
components. These parts are made and tested to HENKE specifications. Non-genuine or “will fit" parts do
not consistently meet these specifications. The use of non-genuine or “will fit” parts may reduce Snow Plow
performance, void HENKE warranties, and present a safety hazard. Use genuine HENKE parts for economy
and safety.

(SNPG-6)

SEE YOUR HENKE DEALER

Always maintain the safety signs in good readable condition. If the safety signs are missing,
damaged, or unreadable, obtain and install replacement safety signs immediately.

(SG-5)

SAFETY

Front & Mid Plow Wings Safety Section 1-3

© 2009 Alamo Group Inc.

SAFETY

All Safety Sh ields, Guards and other Protective Safety devices should be used and
maintained in goo d working condition. All safety devices should be inspected
carefully at least daily for missing or broken components.

NEVER REMOVE
PROTECTIVE SHIELDS AND GUARDS! NEVER MODIFY OR CUT PROTECTIVE SHIELDS OR
GUARDS!

When shields or guards are removed to access areas for maintenance, they must be
replaced and be in good condition before operating. M iss i ng, br o k en, or w orn sh i elds,
guards, and other protective devices must be replaced at once and prior to operation
to reduce the possibility of injury.

(SNPS-02)

The Snow Plow power unit should be equipped with a fire extinguisher, rated for all fires, in
an accessible and visible area. T he fire extinguisher should be inspected routinely by a
certified inspector for operational use an d replaced as needed. Never obstruct access to
the fire extinguisher.

(SNPS-6)

NEVER use drugs or alcohol immediately before or while driving or operating the Snow

Plow. Drugs and alcohol will affect an operator’s alertness and coordination and therefore
affect the operator’s ability to operate the Equipment safely. Before operating the
Equipment, an op erator on prescription or over-the-counter medication must
consult a medical professional regarding any side ef fects of the medication

that would hinder their ability to operate the Equipment safely. NEVER

knowingly allow anyone to op erate this Equipment when their alertness or
coordination is im paired. Serious injury or death to the operator or others
could result if the operator is under the influence of drugs or alcohol.

(SNPD-3)

Always wear OSHA a pproved Personal Protective Equipment (PPE) while operating,
servicing, repairing, and/or cleaning the Equipment. PPE is designed to provide bodily
protection during such activities.

Personal Protective Equipment includes:

-Protective Eye Wear

-Steel Toed Safety Footwear

-Gloves

-Hearing Protection

-Close Fitted Clothing

-Hard Hat-When working around a raised hopper.

-Respirator-Depending on conditions and material being swept or cleaned.

Specialized protective equipment may be required if dangerous or hazardous material is being moved by the
plow.

(SNPD-4)

OPERATOR SAFETY INSTRUCTIONS AND PRACTICES

SAFETY

Front & Mid Plow Wings Safety Section 1-4

© 2009 Alamo Group Inc.

SAFETY

Prolonged operation of the Snow Plow ma y cause operator boredom and/or fatigue
affecting the safe operation of the Snow Plow and Truck or Power unit. It is recommended
that the op erator take scheduled work breaks to help prevent these potentially impaired
operating conditions. If p ossible, completely shut down th e Equipment, exit the cab and
move around stretching your arms and legs. Never operate the Equipment in a fatigued or
bored mental state that impairs proper and safe Equipment operation.

(SNPD-5)

PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE
PERMANENT HEARING LOSS!

Equipment operation can o ften
be noisy enough to cause permanent hearing loss. We
recommend that you always wear hearing protection if the noise in
the Operator’s position exceeds 80db. Noise over 85db over a n
extended period of time wil l cause severe hearing loss. N oise
over 90db adjacent to the Operator over an e xtended period of

time will cause permanent or total hearing loss.

Note:

Hearing
loss from loud noise [from sweepers, chain saws, radios, and
other such sources close to the ear] is cumulative over a lifetime
without hope of natural recovery.

(SNPD-6)

Prolonged operation of the Equipment in col d weather may cau se operator hypothermia
affecting the safe operation of the Snow Plow and Truck or Power unit. It is recommended
that the operator wear appropriate clothing take scheduled work breaks to help prevent
these potentially impaired operating conditions. If pos sible, completely shut down the
Equipment, exit the cab and warm the body in a properly heated area. Never operate the
Equipment in a fa tigued or impair ed mental state that effects the proper and safe
Equipment operation.

(SNPD-8)

Use both hands for support when getting on and off the truck or power unit. Use handles
and steps on the equipment for support when boarding. Never use the Truck or Snow Plow
control levers for support when boarding the equipment.

(SNPO-01)

Use available truck or power unit handles and steps to exit th e operator’s station. Make
sure you have solid footing before stepping down. Be careful of your step and use extra
caution when mud, ice, snow, or other matter has accumulated on the steps or handrails.
Never rush to exit or jump off the truck or power unit.

(SNPO-02)

Do not attempt to mount the Truck or Power Unit while the machine is moving.
Never attempt to mount a run away Snow Plow. Serious injury or death m ay
occur from being run over by a moving Truck, Power Unit, or Snow Plow.

(SNPO-03)

BEFORE leaving the operator’s seat, always engage the parking brake and/or set the
Truck’s or Power Unit’s transmission in the park position, stop the engine, remove the key,
and wait for all moving parts to stop. Never dismount a Truck or Power Unit that is moving
or while the engines are running. Op erate the equipment controls from the Op erator’s
seat only.

(SNPO-04)

SAFETY

Front & Mid Plow Wings Safety Section 1-5

© 2009 Alamo Group Inc.

SAFETY

Always wear a seat belt while driving the equipment during operation and transport.
Serious injury or even death could result fr om falling from the operator’s station or from
being involved in a collision.

(SNPO-05)

Start the engines only when seated and belted in th e operator’s seat. Operate the
equipment controls only while properly seated with th e seat belt secur ed around you.
Inadvertent movement of the power unit or attachment components may cause serious
injury or death to th e operator and passersby. Read the truck or Power Unit o perator’s
manuals for proper starting instructions.

(SNPO-06)

Do not operate, or perform maintenance to, th e Equipment while wearing loose fitting
clothing. Entanglement of loose clothing with the rotating elements can result in serious
injury or death. Stay clear of all rotating elements at all times.

(SNPD-7)

Operate only in conditions where you have clear visibility of the area in d aylight or with
adequate artificial lighting. Never operate in darkness of foggy conditions where you
cannot clearly see at least 50 feet in front and to the sides of the equipment. Make sure
that you can clearly see and identify passersby, steep slopes, ditches, drop-offs, overhead
obstructions, power lines, oversized debris and foreign objects. If yo u are unable to see
these types of items, discontinue operation until visibility improves.

(SNPO-8)

When transporting the Snow Plow be tween locations, follow all local traffic laws and
regulations.

(SNPO-10)

Operate at a speed that allows you to safely operate and control the Truck and Snow Plow.
Safe plowing speed depends on street condition and the type and amount of debris being
moved. Slow down for corners, curbs, parked cars, protruding signs and other obstacles.
Use slow traveling speeds when operating on or near steep slopes, ditches, dr op-offs,
overhead obstructions, power lines, or when debris and foreign objects are to be avoided.

(SNPO-13)

Do not o perate the Equipment if excessive vibration or noise exist s. Shut
down the equipment an d the T ruck or Powe r Unit engine. Inspect th e
Equipment to determine the source of the vibration or noise. If parts are
loose, damaged, or missing, replace them immediately. Do not operate th e
Equipment until all necessary rep airs have been p erformed. To reduce the
possibility of property damage, serious injury, or even death, never operate
the Equipment with missing or damaged components.

(SNPO-16)

Never attempt to plow debris that is too large for the Snow Plow (oversized objects such as
broken limbs and discarded tires). Such objects may damage the snow plow components
and cause serious mechanical damage to the equipment. If possible, carefully place such
objects out of the Snow Plow and traffic path until properly removed by another means.

(SNPO-17)

SAFETY

Front & Mid Plow Wings Safety Section 1-6

© 2009 Alamo Group Inc.

SAFETY

Unplowed snow, piled ice and debris, and snow drifts left behind the equipment might pose
a driving hazard to vehicle traffic colliding with the debris or losing traction on the material.
It is r ecommended to post warning signs alerting driver’s of th e equipment operation
presence and the need to reduce vehicle speed. If such hazards are left behind following
the Snow Plows passage, the area should be plowed a second time and any remaining
hazards removed by an alternative method.

(SNPO-19)

Use extreme caution when lowering the Snow Wing. Make sure no bystanders are close
by or underneath the wing while lowering. Allow ample clearance around the equipment
when lowering or raising the wing. Use e xtreme caution around obstructions including
bystanders, passersby, curbs, buildings, and other property. Use the Truck’s or Power
Unit’s horn to war n of danger when the win g is b eing lowered. Lower wing slowly and
carefully. Sudden or unexpected dropping of wing could result in serious injury.

(SNPO-24)

Do not allow the Snow Plow to come in co ntact with potentially dangerous and/or
hazardous material. Such h azards may includ e, but are not exclusively limited to, the
following:

• Fire Hazards- Fuel spills, burning material,

• Chemical Hazards- Chemical spills, discarded chemical containers, batteries,

• Biological Hazards- Decaying Carcasses, BioMedical Waste,

• Radioactive Hazards-Radioactive Waste, Radioactive Material,

• Carcinogenic Materials-Asbestos,

• Corrosive Materials-Batteries, Acids and Bases.

In most areas, these types of material require special handling requirements for safe and proper disposal and
should not be plowed by the Snow Plow, nor can they be disposed of in a general landfill site like most swept
waste. Contact the appropriate authority for the collection and disposal requirements of such dangerous and/
or hazardous material.

(SNPO-25)

Always wear required OSHA approved Personal Protective Equipment (PPE) when coming
in contact with and removing potentially dangerous and hazardous material that ha s
collected on the Snow Plow equipment or which is obstructing one or more components.
Pay close attention to dangerous and hazardous material including, but not exclu sively
limited to, chemicals, decaying carcasses and sharp objects.

(SNPO-26)

Verbal communication near a T ruck or Power Unit and Snow Plow is d ifficult and
dangerous. Operating instructions and directions should be made prior to starting the
equipment. Unclea r and misunderstood communication may lead to o perator and
bystander injury or death and equipment damage. If com munication by the operator is
necessary, completely shutdown and exit the equipment. Never allow anyone to approach
the equipment while in operation.

(SNPO-28)

Never allow children to play on, under, or around the Truck or Power Unit nor allow children
to operate equipment controls. Children can slip or fall off the equipment and be injured or
killed. Children can cause the equipment components to shift or fall crushing themselves
or others.

(SNPO-29)

SAFETY

Front & Mid Plow Wings Safety Section 1-7

© 2009 Alamo Group Inc.

SAFETY

Allow passengers only in si tuations where their presence is involved in th e operation
(operator training, supervision, maintenance inspection). Never carry passengers whose
presence distracts from the safe op eration or transport of the equipment. Pa ssengers
must be seated securely and belted in the cab’s passenger seat. Never allow any person
to ride on any other location of the Truck, Power Unit or Snow Plow during operation or
transport.

(SNPO-30)

Extreme caution should be used by th e operator when operating near passersby. Stop
snow plowing if a p asserby comes within 25 feet of the plow to prevent possible passerby
injury or death from being struck by the equipment or from a thrown object.

(SNPO-31)

Under certain conditions, the Snow Plow is capable of propelling objects up to 75 feet. Be
extremely careful when plowing at higher speeds and hitting large dense objects, such as
rocks, chucks of frozen ice, metal objects, broken glass, or other solid objects that might
become propelled and cause bodily injury to passersby or damage to property such as
windows and vehicles.

(SNPO-32)

Make sure that no byst ander, animal or obstruction such as a vehicle, building, or
street sign are within the width of the Snow Plow. The design of the Snow Plow may
impair the operator vision when operating. Use extreme caution to ensure that the
Snow Plow is not driven into the path of pedestrian or vehicle traffic. Serious injury
or death and property damage could result from running into, being crushed by, or
run over by a Snow Plow.

(SNPO-33)

Make sure no bystanders or animals are within 25 feet of the e quipment
basket when dump ing contents from or clea ning the Snow Basket. Bucket
contents, which may exceed several thousand pounds, could fall and crush a
bystander or an animal resulting in possible injury or death.

(SNPO-34)

On fully assembled unit, do no t remove the wing retaining chain until hoses
are attached to the power unit and the wing folding cylinders have been filled
with oil. Lower wings slo wly and carefully. Keep bystanders clear of are a
when lowering wings. Sudden or unexpected dropping of wing could result in
serious injury.

(SNPO-36)

Use extreme caution when operating the Equipment in traffic. To alert motorist of the
Equipment’s presence, use all equipped warning signals to alert motorist and pedestrians
of the equipment’s presence and relatively slow speed. Ser ious injury or death and
property damage may occur if a vehicle collides with this Equipment.

(SNPS-3)

Before starting a sn ow plowing operation, make sur e all the warning signal lights are
connected, visible and working. Routinely inspect the equipment’s headlights, brake lights,
backup lights, and turn signal lights for operational condition. Immediately repair non­functioning lighting. Always follow all local traf fic regulations while o perating the Snow
Plow.

(SNPS-4)

SAFETY

Front & Mid Plow Wings Safety Section 1-8

© 2009 Alamo Group Inc.

SAFETY

Always turn on all safety lights and flashers when you operate the Snow Plow. (SNPS-5)

Be particularly careful in transport. The Implement has raised and moved the center of
gravity to the front of the Po wer Unit increasing the poss ibility of overturn and ti pping
forward. Turn curves or go up slopes only at low speed and using a gradual turning angle.
Go up slopes with the Implement located uphill. Slow down on rough or uneven surfaces.

(SPU-2)

Do not stand or allow bystander or coworkers between the attachment
and the truck or powe r unit while ins talling or disconnecting the
attachment. Ke ep hands and body clear of th e attachment and the
attachment mounts. Serious injury or death can result from a person
being crushed between the attachment and truck or power unit.

(SNPC-01)

Reset the tripped snow p low edge by r aising the snow plow off the ground. DO NOT
attempt to reset the trip edge by hand. T he trip edge is spring loaded and sudden and
unexpected movement can o ccur resulting in serious injuries. Kee p and hands and feet
away from the trip edge. If the trip edge does not reset, stop plowing and have the snow
plow repaired before resuming snow plowing.

(SNPO-12)

Make sure the implement is pr operly attached to the Power Unit and the r etaining pins
securely lock th e Implement into position. Im proper mounting of the Imp lement onto the
Power Unit can result in the Implement falling causing serious injury.

(SNPC-02)

The operator of the equipment must be tr ained in the operation and safe use of this
machine. Th e operator must read and completely understand the operator’s manuals of
the Snow Plow, Truck or Power unit manufacturers. New operators should be trained in an
open area clear of obstructions before operating on public roadways. If operation of the
entire Snow Plow unit (Truck or Power unit) is not completely understood, consult your
authorized sales representative for a de tailed explanation. Never allow an untrained or
unqualified driver to operate the Snow Plow.

(SNPD-1)

The Snow Plow driver must meet the requirements and possess a Motor Vehicle License
as determined by the state in which the Snow Plow is operated if used on public roadways.
Contact your local State Department of Public Safety of fice for special licensing
requirements to operate the Snow Plow in your area.

(SNPD-2)

CONNECTING OR DISCONNECTING IMPLEMENT SAFETY INSTRUCTIONS AND PRACTICES

SAFETY

Front & Mid Plow Wings Safety Section 1-9

© 2009 Alamo Group Inc.

SAFETY

Perform service, repairs and lubrication according to the maintenance section. Ensure the
unit is properly lubricated as specified in the lubrication schedule and all bolts and nuts are
properly torqued. Failure to properly service, repair and maintain this Implement in good
operating condition could cause component failure and possible serious injury or even
death.

(SG-35)

Periodically inspect all moving p arts for we ar and replace
when necessary with authorized service parts. Look for loose
fasteners, worn or broken parts, and leaky or loose fittings.
Make sure all pins are properly secured. Serious injury may
occur from not ma intaining this equipment in good working
order.

(SNPM-01)

Inspect the entire Snow Plow before each use. Accidents may occur or damage to the
equipment may result if the Snow Plow is not maintained in g ood mechanical working
order.

• Check for loose bolts, worn or broken parts, pinched hydraulic hoses, and leaky or loose fittings.

• Make sure all pins are secure and safety pin equipped.

• Make sure replacement parts are the correct size and properly installed.

• Make sure all fluid levels are full and replenish as necessary.

• Make sure fuel, oil, and coolant caps are replaced and tightened.

• Check tire condition for tread wear and tire pressure at the rated PSI.

• Make sure that all safety shields and guards are attached and in good condition.

• Make sure all scheduled maintenance is up to date.

(SNPM-02)

Do not modify or alter this Sn ow Plow. Do not permit anyone to modify or
alter this equ ipment, any of its components or any Snow Plow function.
Modification can result in equipment failure and cause serious injuries to the
operator, coworkers, or bystanders.

(SNPM-03)

Use extreme care when climbing onto the equipment to perform repairs, maintenance,
and cleaning. Use proper stands and ladders to access areas that cannot be reached from
ground level. Slipping and falling off the equipment can cause ser ious injury or death.

(SNPM-04)

Never attempt to repair, lubricate, adjust, clean, remove obstructions or perform any other
type of service to any component while the Snow Plow is in motion or while the engine is
running. Completely shut down the engine and wait for all motion to come to a complete
stop before servicing the Snow Plow.

(SNPM-05)

MAINTENANCE AND SERVICE SAFETY INSTRUCTIONS AND PRACTICES

SAFETY

Front & Mid Plow Wings Safety Section 1-10

© 2009 Alamo Group Inc.

SAFETY

Never leave the Snow Plow unattended while the plow is in the raised position. Accidental
operation of the lifting lever or a hydraulic failure may cause a sudden drop of the unit
which could result in injury or death by crushing. If the plow must be raised for inspection
or service securely block up and support the Plow to prevent it falling.

(SNPM-06)

Never crawl under the Snow Plow or any raised component unless it is properly blocked
up and support to prevent it from falling. Accidental operation of a lifting lever or hydraulic
failure may cause a sudden drop of the unit with injury or death by crushing.

(SNPM-07)

Use proper protective equipment including gloves, safety eye wear, arm protection when
handling plow blades and components during replacement, adjustment, and maintenance.
Plow edges and components can become sharp and have burrs that could inflict puncture
and cuts to the hands, arms, and/or eyes if proper protective equipment is not worn.

(SNPM-08)

Replace bent, cracked, or broken plow blade with a new blade. Ne ver attempt to
straighten or weld on plow blades because this will likely crack or otherwise damage the
blade with subsequent failure and possible serious injury from broken blade being ejected
from plow.

(SNPM-10)

Escaping pressurized hydraulic oil generated by hydr aulic pumps has the potential to
inflict serious injury and possible death. Never attempt to repair a pump or hose or tighten
a connection while the system is pre ssurized. Always shu t down the e ngine and relieve
hydraulic oil pressure before performing any repairs to the hydraulic system.

(SNPM-11)

Hydraulic pressure must be relieved from the hydraulic circuit prior to d oing any
maintenance or repair work and when the Snow Plow is parked at the end of the day.
Place the Snow Plow(s) on the ground or securely blocked up. Turn off the Truck engine
then engage the hydraulic remote cylinders several times to relieve hydraulic pressure
prior to performing any maintenance or repair work.

(SNPM-12)

Never remove debris from or unclog jams in the plow or lifting components until the engine
have been completely shutdown and all components have com e to a comp lete stop a nd
are lowered to g round level and hydraulic pressure relieved. Always wear PPE when
removing collected material and debris from the equipment. Serious injury or death may
occur if any of these precautions are not followed when removing plugged or entangled
debris.

(SNPM-15)

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit
chemicals known to the state of California to cause cancer and birth defects or other
reproductive harm.

(SNPM-20)

SAFETY

Front & Mid Plow Wings Safety Section 1-11

© 2009 Alamo Group Inc.

SAFETY

Do not operate this equipment with hydraulic oil or fu el
leaking. Oil and fuel are expensive and their presence
could present a hazard. Do not check for leaks with your
hand! High-pressure oil streams from breaks in the line
could penetrate the skin and cause tissue damage including
gangrene. To check for a hose leak, SHUT the ENGINE OFF and
remove all hydraulic pressure. Wear oil impenetrable gloves, safety
glasses and use Cardboard to check for evidence of oil leaks. If you
suspect a leak, REMOVE the HOSE and have it tested at a Dealer.
If oil does penetrate the skin, have the injury treated
immediately by a physician knowledgeable and skilled in
this procedure.

(SNPM-21)

Always read carefully and fully comply with the manufacturers instructions when handling
fuels, oils, solvents, cleansers, and any other chemical agent.

(SNPM-22)

Battery posts, terminals and related accessories contain lead and lead compounds,
chemicals known to the state of California to cause cancer and birth defects or other

reproductive harm. Wash Hands after handling

. (SNPM-23)

Avoid contact with hot surfaces on the bottom of the skid shoes or plow cutting
edges. Use gloves and eye protection when servicing hot components. Contact
with a hot surface can cause serious injury from burns or scalding.

(SNPM-24)

Remove the negative battery cable from the battery before performing any maintenance on
the electrical system to p revent an accidental circuit shorting and sparks. Sparks can

result in wiring damaged, fire or personal injury.

(SNPM-25)

DO NOT allow any person under a folded wing unless wing is securely supported or locked
up with the safety chain. Never work under a lifted component unless the component is
securely supported or blocked up. Keep bystanders clear of area when lowering wings.
Sudden or unexpected dropping of wing could result in serious injury.

(SNPM-26)

Before conducting maintenance on the Snow Plow stop the truck or Power Unit, place the
transmission in the park position and set the parking brake. Turn the engine off and
remove the key to prevent inadvertent or accidental starting of the engine. Unexpected

engine start up or vehicle movement can result in serious bodily injuries or death.

(SNPM-27)

SAFETY

Front & Mid Plow Wings Safety Section 1-12

© 2009 Alamo Group Inc.

SAFETY

Secure the wing for transport whe n not plowing. Se cure wing in transport
position using wing transport safety chain. Sudden or unexpected dropping of
wing could result in serious injury.

(SNPO-35)

Transport the Truck, Power Unit, and Snow Plow only at safe speeds. Serious accidents
and injuries can result from driving this equipment at unsafe speeds. Become familiar with
the driving characteristics of the equipment and how it han dles before operating or
transporting on streets and highways. Make sure the Truck’s or Power Unit’s steering,
brakes, and wheels are in good condition and operate properly)

Before transporting the Equipment determine the safe transport speeds for you and the machine.
Make sure you abide by the following rules:

• Test the Truck or power unit and Snow Plow at a slow speed and increase the speed slowly. Apply the
brakes smoothly to determine the stopping characteristics of the Truck equipped with the Snow Plow. As
you increase the speed of the Truck, the stopping distance increases. Determine the maximum safe
transport speed for you and the equipment. When driving down a hill or on wet or icy roads, the braking
distance increases: use extreme care and reduce your speed. Do not operate the equipment with weak
or faulty brakes.

• Obey all traffic laws and regulations. Never exceed the posted speed limit.

• The Snow Plow has moved the center of gravity of the equipment forward. Use extreme caution when
transporting at highway speeds. Slow down for sharp corners or on slopes to avoid loss of steering con­trol.

• Only transport the equipment at the speeds determined as safe and which allow for proper control of the
machine while driving and stopping during an emergency.

• When operating in traffic, use the Truck’s or Power Units directional indicator or signal lights to indicate
your movement. Always use the flashing warning lights and other equipped warning features to alert

motorist of your presence and slow moving speed when operating in traffic. Be Aware of Traffic Around
You and Watch Out for the Other Guy.

(SNPO-09)

TRANSPORTING SAFETY INSTRUCTIONS AND PRACTICES

SAFETY

Front & Mid Plow Wings Safety Section 1-13

© 2009 Alamo Group Inc.

SAFETY

Federal Laws and Regulations

This section is intended to explain in bro ad terms the concept and effect of federal laws and regulations concerning

employer and employee equipment operators. This section is not intended as a legal interpretation of the law and

should not be considered as such.

Employer-Employee Operator Regulations

U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA

This Act Seeks:

“...to assure so far as po ssible every wo rking man and woman in the nation safe an d healthful working
conditions and to preserve our human resources...”

DUTIES

Sec. 5 (a) Each employer-

(1) sh all furnish to ea ch of his employees employment and a place of employment which are free from
recognized hazards that are causing or are likely to cause death or serious physical harm to his employees;

(2) shall comply with occupational safety and health standards promulgated under this Act.

(b) Each employee shall comply with occupational safety and health standards and all rules, regulations and
orders issued pursuant to this Act which are applicable to his own actions and conduct.

OSHA Regulations

OSHA regulations state in part: “At the time of initial assignment and at least annually thereafter, the employer
shall instruct every employee in the safe operation and servicing of all equipment with which the employee is,
or will be involved.”

Employer Responsibilities:

To ensure employee safety during plow and truck or other power unit operation, it is the employer’s responsibility to:

1. Train the employee in the proper and safe operation of the plow and truck or other power unit.

2. Require that the employee read and fully understand the plow and truck or other power unit Operator’s manual.

3. Permit only qualified and properly trained employees to operate the plow and truck or other power unit.

4. Maintain the plow and truck or other power unit in a safe operational condition and maintain all shields and guards

on the equipment.

5. Ensure the truck or other power unit is equipped with a functional ROPS and seat belt and require that the

employee operator securely fasten the safety belt and operate with the ROPS in the raised position at all times.

6. Forbid the employee operator to carry additional riders on the Tractor or Implement.

7. Provide the required tools to maintain the plow and truck or other power unit in a good safe working condition and

provide the necessary support devices to secure the equipment safely while performing repairs and service.

8. Require that the employee operator stop operating equipment if bystanders or passersby come within 25 feet.

Child Labor Under 16 Y ear s of Age

Some regulations specify that no one under the age of 16 may operate power machinery. It is yo ur responsibility to

know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard

Administration, Wage & Home Division, Child Labor Bulletin #102.)

SAFETY

Front & Mid Plow Wings Safety Section 1-14

© 2009 Alamo Group Inc.

ASSEMBLY

SECTION

Assembly Section 2-1

ASSEMBLY

Before attempting to mount or service your Tiger
equipment, it is important to read and understand all of the
information in the Safety section of this manual.

Check complete shipment list against the packing list to make sure there are no
shortages. Make certain the tractor model is the appropriate one for the mower received!

Always use a floor jack, hoist or fork lift to lift and raise heavy parts.

Read and understand the entire assembly section instructions before attempting
to mount your Tiger mower. Refer to the parts section of this manual for detailed
illustrations to locate all parts.

Assembly Section 2-2

ASSEMBLY

MULTIPLIER VALVE CONTROLLER MOUNTING

The Multiplier Valve Controller comes with two worm-screw ties that are used to
attach the Controller to the Tractor Joystick as shown below.

The Multiplier Valve Controller can also be attached to the tractors’ joystick by removing
the joystick handle, drilling two holes, and using the 10-32 machine screws and nylock
nuts which are provided.

MULTIPLIER VALVE CONTROLLER WIRING

The red wire coming out of the bottom of the controller should be routed inside the
tractor cab and inserted into the Tractor Auxillary Plug-in. The cable wires should be
routed through the rear window of the tractor cab to the Multiplier Valve.

Black wire: Top button on controller.
White wire: 2nd button on controller.
Orange wire: 3rd button on controller.
Green wire: 4th button on controller.

Black wire

Assembly Section 2-3

ASSEMBLY

HYDRAULIC MULTIPLIER VALVE MOUNTING

Align the mounting bracket to the existing holes on rear of the tractor by the PTO.
Secure the bracket to the tractor with the existing hardware. Then align the holes and
secure the valve to the mounting bracket as shown in the parts section. Install the
electrial control wires from the controller that are routed through the rear window of the
cab. See previous page for wire designation. Install the hydraulic lines from the Multiplier
Valve to the tractor remotes.

PRESSURE FROM
REMOTE

RETURN FROM
REMOTE

MOUNTING BRACKET

FOUR FUNCTION
HYDRAULIC
MULTIPLIER VALVE

EXISTING HARDWARE

Assembly Section 2-4

ASSEMBLY

HYDRAULIC SYSTEM DIAGRAM

Assembly Section 2-5

ASSEMBLY

3-POINT PUSH ARM STOP MOUNTING

Install the Push Arm Stop onto the 3-point hitch using the pins as shown in the
parts illustration. Adjust the bottom arms so the Push Arm Stop is 17” to the ground
at the Pivot Boss. Adjust the top link so that the Push Arm Stop is approximately level
with the ground.

ADJUSTING REAR WHEELS

Follow the instructions in the tractor owners manual for adjusting tires and

rims. The rear wheels MUST be adjusted to the widest setting. NOTE: This may

require switching the wheels to opposite sides of the tractor. Also take note of any width
restrictions when transporting by trailer. (For ease of installation, it is best to leave rear
wheels removed during installation of the mower).

Assembly Section 2-6

ASSEMBLY

WELDING MAIN FRAME

Make sure you use the appropriate safety equipment. Weld the Tangs onto your
existing Main Frame as shown below. Next, weld on the Boss’ making sure the
orientation of the cross holes for the bolts are correct.

ITEM PART NO. QT Y DESCRIPTION

1 06300059 * MAIN FRAME
2 06401066 2 TANG,LEFT,MNFRM
3 06401067 1 TANG,RIGHT,MNFRM
4 06470013 1 BOSS,2.50OD x 1.56ID x 1.00
5 23387A 2 BOSS,2.50OD x 1.53ID x 1.25

Assembly Section 2-7

ASSEMBLY

FINAL PREPARATION FOR OPERATION

Place operators safety and operation decals on the steering column and side counsel
where they are clearly visible to the operator. These decals should be understood by
each operator of the machine in conjunction with the safety and operation section of this
book. The decals are to be maintaned in good condition as a reminder to the operator,
and should be replaced if damaged.

Finally, all bosses, pins and pivot points will need to be greased as instructed in the
maintenance section of this manual. The hydraulic reservoir can also be filled with the
recommended fluid (see maintenance section) and the filter installed in the top of the
tank. Double check all fittings and fasteners BEFORE st arting tractor. Also secure
any loose hoses together with zip ties and wrap with split hoses where friction may
occur on the hoses.

BEFORE starting or operating the tractor you must read and understand
the safety and operation sections of this manual completely.

BE SURE THE BALL V ALVES ARE OPEN! Start tractor and allow instruments to

stabilize. Using a piece of paper or cardboard as noted in the safety and maintenance
sections, check all fittings and connections for hydraulic leaks.

If a leak is found, you must shut down the tractor , set the cutter on the ground.
Before attempting to fix the leak, you must actuate the lift valve handles several times to
relieve any pressure in the lines.

Before operating the plows, the front and side plows should be slowly moved

throughout the full range of motion. Watch for any condition that would cause pinching
or excess stress on the hoses. The steering and front axle travel should also be
carefully moved through their full range of motion. If any condition occurs in which the
hoses contact the tires, the steering and / or front axle travel may need to be limited as
described in the tractor operators manual. This should also be done if the tires rub, or
are extremely close to any other part of the plow. This may include adding shims, or
adjusting stop bolts in the tractor front to solve the problem. While checking motion,
you should also check that the control circuits are connected according to the operators
decal for the valve handles.

Assembly Section 2-8

OPERATION

OPERATION

SECTION

Snow Plow Operation Section 3-1

OPERATION

Safety is of primary importance to the owner / operator and to the manufacturer.

The first section of this manual includes a list of Safety Messages, that, if followed,
will help protect the operator and bystanders from injury or death. Many of the
messages will be repeated throughout the manual. The owner / operator / dealer
should know these Safety Messages before assembly and be aware of the hazards
of operating this mower during assembly, use, and maintenance.

The Safety Alert Symbol combined with a signal word, as seen below, is

intended to warn the owner / operator of impending hazards and the degree of injury
possible during operation.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH
OR VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in
DEATH OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR
INJURY.

IMPORTANT!

Identifies special instructions or procedures that, if not strictly observed, could result
in damage to, or destruction of the machine, attachments or the enviroment.

NOTE: Identifies points of particular interest for more efficient or convienient operation or

repair. (SG-1)

Before any operation of tractor and equipment, the user should read

and understand the safety and operating instructions for both the tractor and

the equipment. The user should also be familiar with the location and
functions of the units instruments and controls. Being familiar with the

machine and it’s controls will increase efficiency and reduce possibility of
serious injury or damage to the unit. The operator should work slowly and carefully
until he feels comfortable with the machine. Speed and skill will be attained much
easier if the necessary time is spent to familiarize yourself with the machine and its
operations.

Since tractor makes and models vary, we recommend reading and following the

operators manual provided by the manufacturer pertaining to your particular unit.

Snow Plow Operation Section 3-2

OPERATION

PUSH ARM STOP POSITION

The Push Arm Stop height is controlled with the 3-point hitch control lever. Follow the
instructions for this control is the tractor operators manual. The 3-point should be set in
its lowest position. With the 3-point in its lowest position, adjust the 3-point arms so that
the Push Arm Stop is level to the ground

After the first day of operation, all bolts should be checked and

tightened securely. This should be done periodically to ensure the bolts do not

become loose and cause damage to the tractor or mower, or injury to the operator.

TRANSPORTING PLOWS

When driving from one site to the next, the following procedure should be followed.

The Front Plow should be raised to its highest position. The chains should be
repositioned to be tight with the plow raised.

The Side Plow should be raised to its transport position. First, raise the Kingpost all the
way to its top position. Secondly, bring the plow up by contracting the swing cylinder.
Verify that the Push Arm is contacting the rubber stop on the Push Arm Stop. If the side
plow isn’t agianst the rubber stop, lower the plow a couple of feet and then raise it back
up. Recheck the position of the plow. When the plow is raised all the way up and against
the rubber stop, shut the tractor off and walk around to the back to strap the chain around
the Push Arm.

Snow Plow Operation Section 3-3

OPERATION

TRANSPORTING MOWER ON A TRAILER

Transporting unit by flatbed trailer:

Most tractors with a side mounted plow attached will be over legal transporting
width (102” wide). For this reason, one of the following procedures must be
followed.

1: Transporting with side plow attached: Use a loading dock or ramp to load
tractor onto the trailer. Center the tractor with the plows attached between the sides
of the trailer. Make sure the side plow is fully raised and secured. Secure the
tractor to the trailer with chains. Obtain proper over-width permits and mark the
vehicle and plow as over-width as required be law. Check the tractor operators
manual for any tractor requirements to transport by flatbed trailer.

2: Transporting with side plow removed: Park the tractor and turn the engine off.
Center the tractor and the plows between the sides of the trailer. Secure the tractor
and the plows to the trailer with chains.

Snow Plow Operation Section 3-4

OPERATION

TRACTOR PRE-OPERA TION Inspection

Tractor ID#____________ Make_____________________
Date:__________________ Shift______________________

Before conducting the inspection, make sure the T ractor engine is off, all rotation
has stop and the tractor is in the Park with the parking brake engaged. The
Mower head is resting on the ground (or is securely blocked up and supported)
and all hydraulic pressure has been relieved.

Operators Signature:___________________________________________________________________

DO NOT OPERATE an UNSAFE TRACTOR or MOWER

Snow Plow Operation Section 3-5

OPERATION

Snow Plow Operation Section 3-6

MAINTENANCE

SECTION

Maintenance Section 4-1

IN SEASON MAINTENANCE

Snow removal equipment must be cared for and maintained regularly. Daily or
pre-route inspection and maintenance are necessary. Failure to do so may affect
efficiency and safety.

A visual inspection must be carried out after every 8 hours of operation. Look for

damaged components, bends, cracked welds or hydraulic leaks. REPAIR

IMMEDIATELY!

of use and to regularly check for loosened or missing fasteners. Replace any
damaged or missing fasteners immediately.

Because of the environment in which snow equipment is expected to operate,
hydraulic lines, fasteners, wearable or replaceable items and warning decals may
become damaged by snow, ice and road debris. These items must be inspected
daily and replaced if necessary to avoid equipment damage or personal injury.

Lubrication of moving parts is of the utmost importance. Exposure to snow, ice,
salt and road debris will wash away lubrication quickly and it may be necessary
to inspect and reapply lubrication more than once a day.

It is recommended to re-torque all bolts after the first 8 hours

Page 2 of 3

END OF SEASON MAINTENANCE

GROUND ENGAGING COMPONENTS

CUTTING EDGES & GUARDS

Replace any broken cutting edges, unevenly or excessively worn cutting edges, and
broken or worn wear guards.

RUNNING GEAR

Replace broken, worn, or missing running gear shoes, and any damaged adjuster
leg components. Gr ease internal threads and sliding members (it’s best to
disassemble and grease directly; zerks aren’t as effective at greasing these areas).

HARDWARE

Replace missing or broken bolts. Proper torque is important! U se grade 8 pl ow
bolts for steel cutting edges.

HYDRAULICS

HOSES

Plug or cap any QC fittings or any open hose ends. Inspect hoses for any leaks or
potential leaks. Secure hoses with hose clamps.

CYLINDERS

Check for leaks, and any chrome rod dents or scratches. (If v-stack rod end seals
are leaking, a ¼ turn of the pack nut will often stop a small leak). Apply a light coat
of oil or grease on exposed rod surfaces.

FRAME AND MOLDBOARD

JOINTS

Check pins, bushings, and pivot bolts for wear. Make sure all keepers are in place.
Make sure shear bolts and pins are same as original equipment (usually grade 2).
Some drivers don’t like replacing shear pins and will install grade 8 replacements to

avoid replacing during a st orm. These items are designed to shear to protect the
driver and the equipment. CHECK WELDMENTS FOR CRACKS.

REPLACE WORN OR BROKEN PARTS FOUND BY ABOVE INSPECTIONS.

Page 3 of 3

NOTES

JD62-6430 SNOW PLOW

PARTS

SECTION

Parts Section 5-1

P ARTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in
processing purchase orders for the equipment in this manual.

1. The Parts Section is prepared in logical sequence and grouping of parts that
belong to the basic machine featured in this manual. Part Numbers and
Descriptions are given to help locate the parts and quantities required.

2. The Purchase Order must indicate the Name and Address of the person or
organization ordering the parts, who should be charged, and if possible, the serial
number of the machine for which the parts are being ordered.

3. The purchase order must clearly list the quantity of each part, the complete
and correct part number, and the basic name of the part.

4. The manufacturer reserves the right to substitute parts where applicable.

5. Some parts may be unlisted items which are special production items not
normally stocked and are subject to special handling. Request a quotation for such
parts before sending a purchase order.

6. The manufacturer reserves the right to change prices without prior notice.

NOTE: When ordering replacement decals, refer to the part numbers and

descriptions listed in the safety section in the front of this manual.

For maximum safety and to guarantee optimum product reliability,
always use genuine
replacement parts may cause premature or catastrophic failure
which could result in serious injury or death.

Tiger replacement parts. The use of inferior

Direct any questions regarding parts to:

Tiger Corporation

3301 N. Louise Ave.

Sioux Falls, SD 57107

1-800-843-6849

1-605-336-7900

JD6030 SNOW PLOW Parts Section 5-2

P ARTS SECTION T ABLE OF CONTENTS

SECTION PAGE
TRACTOR SPECIFIC PARTS:

TRACTOR MOUNT KIT - MAIN FRAME 5-4

TRACTOR MOUNT KIT - FRONT HYDRAULICS 5-5

TRACTOR MOUNT KIT - PUMP HOSES 5-6

TRACTOR MOUNT KIT - SIDE HYDRAULICS 5-8

3-POINT STOP & PUSH ARM 5-10

MULTIPLIER VALVE MOUNTING 5-12

3 & 4 FUNCTION MULTIPLIER VALVE BREAKDOWN 5-13

2 FUNCTION MULTIPLIER VALVE BREAKDOWN 5-14

1 FUNCTION MULTIPLIER VALVE BREAKDOWN 5-15

SAFETY LIGHTS 5-16

JD6030 SNOW PLOW Parts Section 5-3

01-31-07

TRACTOR MOUNT KIT - MAIN FRAME

ITEM PART NO. QT Y DESCRIPTION

1 REF * MAIN FRAME
2 06300118 1 SIDE PLOW WELDMENT
3 21688 3 CAPSCREW,7/16 x 3-1/4,NC
4 06420125 2 PIN,1.50 X 4
5 21677 3 NYLOCK NUT,7/16,NC
6 06300116 1 PUSH FRAME
7 33764 8 FLATWASHER,5/8,SAE,GR8
8 21777 4 NYLOCK NUT,5/8,NC
9 06300113 1 HANGER FRAME
10 33880 10 FLATWASHER,3/4,SAE,GR8
11 ------ 2 CAPSCREW *EXISTING TRACTOR HARDWARE
12 32382 4 CLAMP,HOSE
13 28399 4 CAPSCREW,20MM x 80MM,2.5P,GR10.9
14 6T2289 4 CAPSCREW,5/8 x 2,NC,GR8
15 21835 2 CAPSCREW,3/4 x 2-3/4,NC
16 6T2607 2 FLATWASHER,3/4,CUT
17 22021 2 FLATWASHER,3/4
18 21993 2 LOCKWASHER,3/4
19 21825 2 HEX NUT,3/4,NC
20 6T3001 1 PIN,1-1/2

JD6030 SNOW PLOW Parts Section 5-4

12-07-06

TRACTOR MOUNT KIT - FRONT HYDRAULICS

ITEM PART NO. QT Y DESCRIPTION

1 REF * MAIN FRAME
2 32900 5 QUICK CPLR,MALE,1/2 x 1/2FOR
3 33271 4 ADAPTER,1/2MOR x 3/8MJ
4 06500510 2 HOSE,1/4 x 170
5 06503147 2 FITTING,BLKHD,1/2MJ x 1/2MOR
6 33382 2 ELBOW,1/2MOR x 1/2MJX90
7 06500164 1 HOSE,1/4 x 216
8 06500228 1 HOSE,1/4 x 204
9 06503148 1 QUICK CPLR,FEM,1/2 x 1/2FOR
10 REF 2 HOSE,1/2 *REFER TO FRONT PLOW ASSY
11 REF 2 ELBOW *REFER TO FRONT PLOW ASSY
12 REF 1 CUSHION VALVE *REFER TO FRONT PLOW ASSY

JD6030 SNOW PLOW Parts Section 5-5

12-07-06

TRACTOR MOUNT KIT - PUMP HOSES

REPLACE EXISTING HOSES
IF NECESSARY

ITEM PART NO. QT Y DESCRIPTION

1 06500258 1 HOSE,1-1/4 x 70 (FROM TANK TO PUMP)
2 TF4852 2 FLANGE KIT,#20
3 06500512 1 HOSE,1 x 70 (FROM PUMP TO BRAKE VALVE)

JD6030 SNOW PLOW Parts Section 5-6

NOTES

PAGE INTENTIONALLY

LEFT BLANK

JD6030 SNOW PLOW Parts Section 5-7

TRACTOR MOUNT KIT - SIDE HYDRAULICS

JD6030 SNOW PLOW Parts Section 5-8

12-04-06

TRACTOR MOUNT KIT - SIDE HYDRAULICS

ITEM PART NO. QTY. DESCRIPTION

1 REF * MAIN FRAME
2 32900 4 QUICK CPLR,MALE,1/2 x 1/2MOR
3 33271 6 ADAPTER,1/2MOR x 3/8MJ
4 06500345 2 HOSE,1/4 x 171
5 32810 2 ELBOW,1/2ORB x 3/8MJ 90 ADJ
6 34073 1 ADAPTER,1/2MOR x 1/2FOR
7 06503030 2 ELBOW,3/8MJ x 3/8MJ 90 ADJ
8 06500511 2 HOSE,1/4 x 161

JD6030 SNOW PLOW Parts Section 5-9

12-04-06

3-POINT STOP & PUSH ARM

JD6030 SNOW PLOW Parts Section 5-10

3-POINT STOP & PUSH ARM

ITEM PART NO. QTY. DESCRIPTION

1 TB1036 1 PIN,TOP LINK,3-POINT
2 T
3 TF1120 2 PIN,(CAPPED),1-1/8 x 3-7/8
4 06300115 1 3PNT,SNWPLW
5 7030084 2 TOPLOCK NUT,5/8
6 2100-1360 2 SPACER,1/4 (USE AS NEEDED)
7 2300-0620 1 RUBBER STOP
8 7040006 2 FLATWASHER,5/8,SAE
9 7020162 2 CAPSCREW,5/8 x 3
10 7020082 1 CAPSCREW,3/4 x 3-1/2
11 7030030 1 TOPLOCK NUT,3/4
12 219-0632 1 PUSH BEAM ASSY
13 2100-0384 1 HINGE ASSY
14 7050028 2 ROLL PIN,3/8 x 2
15 2100-1280 1 PIN,1-1/4

F1143 3 PIN, LYNCH, 7/16 x 2

JD6030 SNOW PLOW Parts Section 5-11

MULTIPLIER VALVE MOUNTING

ITEM PART NO. QTY. DESCRIPTION

1 32900 2 QUICK CPLR,MALE,1/2 x 1/2FOR
2 33382 2 ELBOW,1/2MOR x 1/2MJ X 90
3 06500251 1 HOSE,1/2 x 28
4 21577 4 NYLOCK NUT,5/16,NC
5 06500122 1 HOSE,1/2 x 30
6 33528 2 ADAPTER,1/2MOR x 1/2MJIC
7 21579 4 CAPSCREW,5/16 x 3/4,NC
8 06505159 1 KIT,HYD MULTIPLIER,4 FUNCTION
9 06503148 8 QUICK CPLR,FEM,1/2 x 1/2FOR
10 31329 8 ADAPTER,1/2ORB x 1/2ORB ADJ
11 * REF TRACTOR HARDWARE
12 06411034 1 MOUNT,MULTIPLIER

JD6030 SNOW PLOW Parts Section 5-12

3 & 4 FUNCTION MULTIPLIER VALVE BREAKDOWN

ITEM PART NO. QT Y DESCRIPTION

1 * REF SMALL NUT (NOT FOR PARTS SALE)
2 06505165 REF SOLENOID 12V SP
3 06505164 REF N/C CARTRIDGE (SPOOL W/SHORT NUT)
4 * REF MANIFOLD (NOT FOR PARTS SALE)
* 06510231 1 CONTROLLER,4 BUTTON (NOT SHOWN)
* 06505167 REF O-RING SEAL KIT (NOT SHOWN)

JD6030 SNOW PLOW Parts Section 5-13

2 FUNCTION MULTIPLIER VALVE BREAKDOWN

ITEM PART NO. QT Y DESCRIPTION

1 * REF SMALL NUT (NOT FOR PARTS SALE)
2 06505165 4 SOLENOID 12V SP
3 06505163 2 N/O CARTRIDGE (SPOOL W/SHORT NUT)
4 * REF MANIFOLD (NOT FOR PARTS SALE)
5 06505164 2 N/C CARTRIDGE (SPOOL W/SHORT NUT)
* 06510230 1 CONTROLLER,1 BUTTON (NOT SHOWN)
* 06505167 AVAIL O-RING SEAL KIT (NOT SHOWN)

JD6030 SNOW PLOW Parts Section 5-14

1 FUNCTION MULTIPLIER VALVE BREAKDOWN

TWO REQUIRED

ITEM PART NO. QT Y DESCRIPTION

1 * REF TALL NUT (NOT FOR PARTS SALE)
2 06505162 2 SOLENOID 12V SS
3 06505161 1 N/O CARTRIDGE (POPPET W/TALL NUT)
4 * REF MANIFOLD (NOT FOR PARTS SALE)
5 06505160 1 N/C CARTRIDGE (SPOOL W/SHORT NUT)
6 * REF SHORT NUT (NOT FOR PARTS SALE)
7 31329 1 ADAPTER,1/2ORB x 1/2ORB ADJ
8 32900 1 QUICK COUPLER,MALE 1/2 x 1/2FOR
* 06510230 1 CONTROLLER,1 BUTTON (NOT SHOWN)
* 06505166 AVAIL O-RING SEAL KIT (NOT SHOWN)

JD6030 SNOW PLOW Parts Section 5-15

SAFETY LIGHT ASSEMBLY

SAFETY LIGHT INSTALLATION

1. Install marker light asy onto the mounting bracket, running wires inside bracket tube.

2. Remove and retain panel under right rear fender that protects wiring.

3. Remove and discard back three screws and clips securing the right rear fender to the cab.

4. Install mtg. bracket to points in previous step with three 1/4" x 3/4”NC bolts and nylock nuts.

5. Using the mounting bracket as a template to drill two holes (13/64 dia.) and tap(1/4"NC) in the
wheel well (Note: Use caution not to drill into the filter housing located behind the cab).

6. Secure bottom of mounting Bracket to wheel well with two 1/4" x 3/4"NC bolts and lockwashers.

7. Next remove the top cover of the tractor cab.

8. Drill two holes 5/8" dia, one in the fender under the air duct at the right rear corner of the cab and
the other at the right rear corner of the cab just inside the air duct.

9. Install grommets in the 5/8 “ dia holes.

10. Route wire from mounting bracket into the area that will be covered by the panel removed in step
2, then through grommets and up into area above cab, install wires ends into connector shell and
close strain relief (Note: Green wire to green wire when mated with adapter harness).

11. Splice the green wire from the adapter harness into the purple wire coming from right rear hazard
light using heat shrink butt connector.

12. Splice the black wire from the adapter harness into the black wire coming from right rear hazard
light using heat shrink butt connector.

13. Connect the adapter harness to the marker light harness.

14. Test for proper operation, the marker light should flash with hazards & right turn signal but should
burn steady when left turn signal is in use.

15. Reinstall top cover of tractor cab and panel in fender to protect wiring.

ITEM P/N QTY DESCRIPTION

* 06200420 AVAIL SAFETY LIGHT KIT (INCLUDES ITEMS 1 THRU 9)
1 34800 1 MOUNT,JD62-6420,ASAE 279.11
2 21529 5 CAPSCREW,1/4" X 3/4" NC
3 21527 3 NUT,NYLOCK,1/4" NC
4 34859 1 MARKER LIGHT ASY
5 21986 2 LOCKWASHER 1/4”
6 31592 2 GROMMET, RUBBER, 5/16 X 13/16
7 1 ADAPTER HARNESS
8 35164 2 CONNECTOR, BUTT H-SHRINK
9 6T1824 2 ZIP TIE (NOT SHOWN)

JD6030 SNOW PLOW Parts Section 5-16

R 03-01

WARRANTY

SECTION

Warranty Section 6-1

W ARRANTY INFORMA TION

Tiger Corporation, 3301 N. Louise, Sioux Falls, South Dakota, warrants to the
original Retail Customer, the new Tiger equipment is free of defects in material and
workmanship. Any part of equipment that in Tiger’s judgement, show evidence of
such defects will be repaired or replaced without charge, provided that the failure of
part(s) shall have occurred within twelve (12) months from the date of delivery of
said equipment to the Retail Customer. Expendable components such as knives,
oil, chain sprockets, skid shoes, knife mounting disks and the like are excluded but
not limited to this warranty.

The Retail Customer must pay the transportation cost to and from the Tiger
Dealer’s service shop for warranty service. Warranty service will be performed by
the Tiger Dealer from whom the equipment was purchased, during service shop
regularly scheduled days and hours of operation.

All Tiger obligation under this warranty shall be terminated if the equipment is
modified or altered in ways not approved in writing by Tiger, if repair parts other than
genuine Tiger repair parts have been used, or if the equipment has been subject to
misuse, neglect, accident, improper maintenance or improper operation.

Tiger Corporation reserves the right to make improvements in design or
changes in specification at any time without incurring any obligation to owners of
equipment previously sold.

No agent or person has authority to alter, add to or waive the above warranties
which are agreed to be in the only warranties, representations or promises,
expressed or implied, as to the quality or performance of the products covered and
which do not include any implied warranty of merchantability or fitness. In no event
will Tiger be liable for incidental or consequential damages or injuries, including, but
not limited to, loss of profits, rental or substitute equipment or other commercial
loss.

THERE ARE NO W ARRANTIES WHICH EXTEND

BEYOND THOSE EXPRESSED HEREIN.

It is the Purchasers obligation to sign the warranty registration form AFTER he /

she has
within this manual.

Read and Understands the Operation and Safety Instructions stated

ONE LAST WORD

This manual cannot possibly cover all of the

potentially hazardous situations you will

encounter. By being familiar with the

safety rules, operating and maintenance

instructions in this manual you can help prevent

accidents. The objective of this manual is to

help make you a better operator. Remember,

SAFETY IS YOU!

Your safety and the safety of those around you

depends on YOU. Common sense should

play a large role in the operation of this machine.

Since we at Tiger Corporation are constantly striving to improve out products, we

reserve the right to change specifications or design at any time.