Tie Down Slotted Receiver with Cross Beam User Manual
Slotted Receiver
with Cross Beam
MAKE YOUR DOCK A DESTINATION
Warnings
Dock Sides Slotted With Cross Beam Receivers
are designed to be used on solid side panel style
aluminum or steel docks only. Please refer to
dock manufacturers product specifications to
determine if dock can accommodate receiver
installation plus the weight of accessories and
items/persons placed on them.
Caution should be used when operating electrical
tools near water. Failure to use caution can result
in injury or death.
9
10
11
6
GalvX #86901 / Galvanized #86919
Tools Required:
Pencil, Tape Measure,
Cordless Drill, 1/8” & 1/2“ Drill Bit,
9/16” Wrench or Socket and
assistance will be needed
7
8
to secure cross beam.
Bottom View
5
Top View
GalvX Dual Coat Finish - #86901 Parts List
# Part # Qty Description
1 86901-3A 1 Slotted Receiver (Complete Assembly)
2 13211 4 5/16"-18 x 3" Eye Bolt, Zinc
3 10637 4 5/16"-18 Flange Nut
4 10598 2 6" Nylon Lanyard
5 86901-2 1 Slotted Receiver Cross Beam Mounting Plate
6 86901-1A 1 4' Cross Beam
7 10841 4 3/8" Flat Washer, Zinc
8 10538 4 3/8" 16 x 1" Bolt, Zinc
9 10016 4 1/2" 13 x 1" Bolt, Zinc
10 10527 4 1/2" Flat Washer, Zinc
11 10645 4 1/2" Nyloc Hex Nut
3
4
11
9
10
11
1
2
10
9
Hot Dipped Galvanized Finish - #86919 Parts List
# Part # Qty Description
1 86919-1A 1 Slotted Receiver (Complete Assembly)
2 13211 4 5/16"-18 x 3" Eye Bolt, Zinc
3 10637 4 5/16"-18 Flange Nut
4 10598 2 6" Nylon Lanyard
5 86919-2 1 Slotted Receiver Cross Beam Mounting Plate
6 86919-1A 1 4' Cross Beam
7 10841 4 3/8" Flat Washer, Zinc
8 10538 4 3/8" 16 x 1" Bolt, Zinc
9 10016 4 1/2" 13 x 1" Bolt, Zinc
10 10527 4 1/2" Flat Washer, Zinc
11 10645 4 1/2" Nyloc Hex Nu
Instruction Sheet #08179
TIE DOWN ENGINEERING • 255 Villanova Drive SW • Atlanta, GA 30336
www.tiedown.com (404) 344-0000 Fax (404) 349-0401
070814,A1293
Slotted Receiver with Cross Beam
GalvX #86901 / Galvanized #86919
Installation Instructions for
4 foot wide docks :
1. Determine location of receiver based on
accessories to be used with it.
2. Receiver must be located at a location allowing
the cross beam to span the underside of the
dock and meet up with the Cross Beam
Mounting Plate on the opposite side
3. On the slotted receiver side of the dock drill
(2) 1/8" pilot holes in the bottom flange of the
side panel at 6.5" on center. Enlarge holes
using 1/2" drill bit. See exhibit 1.
4. Mount the slotted receiver in the holes using
2 of the 1/2" x 1" bolts (#9), 1/2" flat washers
(#10) and 1/2" nyloc hex nuts (11).
See exhibit 2
5. On the dock side opposite the receiver drill
(2) - 1/8" pilot holes in the bottom flange of the
side panel at 2" on center. Enlarge holes using
1/2" drill bit. See exhibit 3
6. Mount the cross beam mounting plate in the
holes using 2 of the 1/2" x 1" bolts, 1/2" flat
washers and 1/2" nyloc hex nuts. See exhibit 4
7. With the help of an assistant attach the cross
beam (6) to the receiver (5) and cross beam
mounting plate (1) using 2 each of the 3/8"
16x1" bolts (8) and flat washers (7) on each
side. See exhibits 2 & 4.
8. For Dock Side Accessories requiring two
receivers, the bolts securing the receiver to the
bottom flange of the side panel may need to be
loosened to allow proper alignment and
insertion of accessory support tubes.
Instruction Sheet #08179
Exhibit 1
Exhibit 2
Exhibit 3
Exhibit 4
5
9
6.5”
6
7
8
2.0”
11
10
1/8” pilot hole
enlarged to 1/2”
11
10
1
9
1/8” pilot hole
enlarged to 1/2”
6
7
8
TIE DOWN ENGINEERING • 255 Villanova Drive SW • Atlanta, GA 30336
www.tiedown.com (404) 344-0000 Fax (404) 349-0401
070814,A1293
Loading...