Tie Down Slotted Receiver User Manual

Slotted Receiver

with Flange

MAKE YOUR DOCK A DESTINATION

Warnings

Dock Sides Slotted Receivers with Flange are designed to
be used on wooden or solid steel side panel docks/decks
only. Please refer to dock/deck manufacturers product
specifications to determine if dock can accommodate
receiver installation plus the weight of accessories and
items/persons placed on them.

Dock Sides Slotted Receivers with Flange should only be
installed on wood docks/decks that are free of defects,
wood decay and/or rot. Periodic inspections of wood
supporting Dock Sides Receivers is required and wood must
be replaced if decay or defects are present.

Caution should be used when operating electrical tools near
water. Failure to use caution can result in injury or death.

GalvX Dual Coat Finish - #86902 Parts List
# Part # Qty Description

1 86902-1 1 Flanged Slotted Receiver
2 13211 4 5/16”-18 x 3" Eye Bolt, Zinc
3 10637 4 5/16”-18 Flange Nut
4 10598 2 6" Nylon Lanyard
5 10680 2 3/8” x 2-1/2" Galv Carriage Bolt
6 10017 3 3/8" Galv Flat Washer
7 10014 2 3/8" Galv Hex Nut
8 10678 1 3/8” x 3-1/2” Galv Lag Bolt

GalvX #86902 / Galvanized #86920

Tools Required:

Pencil

Tape Measure

Cordless Drill

3/8" Drill Bit
1/4" Drill Bit

9/16” wrench or socket

5

5

1

6

7

2

Hot Dipped Galvanized Finish - #86920 Parts List
# Part # Qty Description

1 86920-1 1 Flanged Slotted Receiver
2 13211 4 5/16"-18 x 3" Eye Bolt, Zinc
3 10637 4 5/16"-18 Flange Nut
4 10598 2 6" Nylon Lanyard
5 10680 2 3/8" x 2-1/2" Galv Carriage Bolt
6 10017 3 3/8" Galv Flat Washer
7 10014 2 3/8" Galv Hex Nut
8 10678 1 3/8" x 3-1/2" Galv Lag Bolt

Instruction Sheet #08177

TIE DOWN ENGINEERING • 255 Villanova Drive SW • Atlanta, GA 30336

www.tiedown.com [phone] Fax [phone]

2

4

4

3

6

8

011713,A1291

Slotted Receiver with Flange

GalvX #86902 / Galvanized #86920

Assembly/Installation Instructions:

1. Determine location of receiver based on
accessories to be used with it.

2. Receiver must be located at the “T” junction of
dock/deck side panel and floor joist. If a floor joist
is not available at desired location, one will need to
be added to dock/deck.

3. Drill (2) 3/8" holes in the dock/deck side panel at
6" on center, 1.5" up from the bottom of the panel.
The holes need to be spaced at equal distances
from the center of the“T” junction. See exhibit 1.

4. Using carriage bolts (5), flat washers (6) and hex
nuts (7) secure the receiver to the dock/deck
with a 9/16” wrench and socket. See exhibit 2.

3.0”3.0”

1.5”

6.0”

Exhibit 1

7 6

5

5. With the receiver in place, locate the slot farthest
back and drill a 1/4" pilot hole. See exhibit 3.

6. Install and tighten the lag bolt (8) and flat washer
(6) in the pilot hole.

7. For Dock Sides Accessories requiring two receivers,
the carriage and lag bolts may need to be loosened
to allow proper alignment and insertion of
accessory support tubes.

8. Inspect and tighten all bolts after the Dock Sides
accessories have been installed.

Exhibit 2

Exhibit 3

Drill pilot hole here

8

6

TIE DOWN ENGINEERING • 255 Villanova Drive SW • Atlanta, GA 30336

www.tiedown.com [phone] Fax [phone]