Tie Down Single Kayak Rack User Manual

Single Kayak Rack

MAKE YOUR DOCK A DESTINATION

GalvX #86903 / Galvanized #86921

Warnings

Caution should be used when operating electrical tools near

water. Failure to use caution can result in injury or death.

8

2

4

3

7

5

4

6

3

Tools Required:

#2 Phillips Head Screw Driver

7/16” Wrench or Socket

1

GalvX Dual Coat Finish - #86903 Parts List
# Part # Qty Description

1 86909-1A 2 Accessory Support Tube
2 86904-2 2 Kayak Bracket
3 48668-C1 4 Bracket Pad
4 10964 4 1/4" x 2.75" Pan Head
Machine Screw, Zinc
5 10929 4 1/4" x 0.5" Pan Head Machine
Screw, Zinc
6 10029 4 1/4" Acorn Nut, Black Nylon
7 10656 4 1/4" Nyloc Nut
8 17511 2 2" Sq. Tube Plug
9 18256 2 2"x 3' Cam Strap

Instruction Sheet #08183

Hot Dipped Galvanized Finish - #86921 Parts List
# Part # Qty Description

1 86927-1A 2 Accessory Support Tube
2 86922-2 2 Kayak Bracket
3 48668-C1 4 Bracket Pad
4 10964 4 1/4" x 2.75" Pan Head
Machine Screw, Zinc
5 10929 4 1/4" x 0.5" Pan Head Machine
Screw, Zinc
6 10029 4 1/4" Acorn Nut, Black Nylon
7 10656 4 1/4" Nyloc Nut
8 17511 2 2" Sq. Tube Plug
9 18256 2 2" x 3' Cam Strap

TIE DOWN ENGINEERING • 255 Villanova Drive SW • Atlanta, GA 30336

www.tiedown.com [phone] Fax [phone]

012513,A1298

Single Kayak Rack

GalvX #86903 / Galvanized #86921

Assembly Instructions:

1. Using 2 - 1/4" x 0.5" pan head screws (5) and
2 - 1/4" acorn nuts (6) attach bracket pads (3) to
bottom of Kayak brackets (2). See exhibit 1

2. Kayak brackets can be mounted on either side of
accessory support tubes (facing toward dock or
away from dock). Determine which side you prefer
and proceed to step 3.

3. Slide 2 - 1/4" x 2.75" pan head screws (4) through
bracket pads (3) and then through vertical portion
of Kayak bracket (2), then secure bracket to
support tube stand (1) using 2 - 1/4" nyloc nuts (7).
See exhibit 3.

4. Repeat steps 1-3 for the remaining kayak rack.

Exhibit 1

Exhibit 2

Dock Side

Placement

2

5

6

4

3

Away Side

Placement

Exhibit 3

Eye bolts secure the receiver

to the kayak rack base.
Once the holes are aliened
hand tighten all eye bolts.

7

4

3

1

Installation Instructions:

1. Slide base of accessory tube into receiver until
threaded holes align with holes in receiver.

2. Slide eye bolts through receiver side holes and screw
into threaded holes in accessory base. Hand tighten all
eye bolts and then use screw driver shaft to tighten
one half turn.

3 Secure kayak to rack using 2 - 3' cam straps (9).

TIE DOWN ENGINEERING • 255 Villanova Drive SW • Atlanta, GA 30336

www.tiedown.com [phone] Fax [phone]

012513,A1298