Tie Down Canoe Rack User Manual
Clamp Receiver
with Cross Beam
MAKE YOUR DOCK A DESTINATION
Warnings
Dock Sides Clamp Receivers are designed to be used
on truss style aluminum or steel docks only. Please
refer to dock manufacturers product specifications to
determine if dock can accommodate receiver
installation plus the weight of accessories and
items/persons placed on them.
Caution should be used when operating electrical tools
near water. Failure to use caution can result in injury
or death.
9
5
6
7
GalvX #86900 / Galvanized #86918
Tools Required:
9/16 wrench or socket
Assistance will be needed
to secure cross beam
8
Upside Down View
Top View
GalvX Dual Coat Finish - #86900 Parts List
# Part # Qty Description
1 86900-1A 1 Clamp Receiver (Complete Assembly)
2 13211 4 5/16”-18 x 3" Eye Bolt, Zinc
3 10637 4 5/16”-18 Flange Nut
4 10598 2 6" Nylon Lanyard
5 86900-2A 1 Clamp Receiver Cross Beam Mounting Plate
6 86901-1A 1 4' Cross Beam
7 10841 4 3/8" Flat Washer, Zinc
8 10538 4 3/8" 16 x 1" Bolt, Zinc
9 10022 4 3/8" 16 x 1-1/2" Bolt, Zinc
3
2
4
1
9
Hot Dipped Galvanized Finish - #86918 Parts List
# Part # Qty Description
1 86918-1A 1 Clamp Receiver (Complete Assembly)
2 13211 4 5/16”-18 x 3" Eye Bolt, Zinc
3 10637 4 5/16”-18 Flange Nut
4 10598 2 6" Nylon Lanyard
5 86918-2A 1 Clamp Receiver Cross Beam Mounting Plate
6 86919-1A 1 4' Cross Beam
7 10841 4 3/8" Flat Washer, Zinc
8 10538 4 3/8" 16 x 1" Bolt, Zinc
9 10022 4 3/8" 16 x 1-1/2" Bolt, Zinc
Instruction Sheet #08178
TIE DOWN ENGINEERING • 255 Villanova Drive SW • Atlanta, GA 30336
www.tiedown.com (404) 344-0000 Fax (404) 349-0401
070814,A1292
Clamp Receiver with Cross Beam
GalvX #86900 / Galvanized #86918
Cross Beam
Mounting Plate
Cross Beam
Exhibit 1
Installation Instructions for
4 foot wide docks :
1. Determine location of receiver based on
accessories to be used with it.
2. Receiver must be located at a location allowing the
cross beam to span the underside of the dock and
meet up with the Cross Beam Mounting Plate on the
opposite side.
3. Position the clamp receiver (#1) on the lower
truss rail and secure in place with 3/8" x 1-1/2”
bolts (#9). See exhibit 2.
6
7
8
Exhibit 2
Clamp Receiver
1
4. On the dock side opposite of the receiver, secure
cross beam mounting plate to lower truss rail with
3/8" x 1-1/2 bolts (#9). See exhibit 3.
5. With the help of an assistant attach the cross beam
(#6) to the receiver (#1) and cross beam mounting
plate (#5) using 2 each of the 3/8" x 1" bolts (#8)
and flat washers (#7) on each side.
6. For Dock Side Accessories requiring two receivers,
the bolts securing the receiver and cross beam
mounting plate to lower truss rail may need to be
loosened to allow proper alignment and insertion of
accessory support tubes.
7. Inspect and tighten all bolts after Dock Sides
Accessory has been installed.
Instruction Sheet #08178
6
5
9
7
8
Exhibit 3
TIE DOWN ENGINEERING • 255 Villanova Drive SW • Atlanta, GA 30336
www.tiedown.com (404) 344-0000 Fax (404) 349-0401
070814,A1292
Loading...