Page 1
Industry
Standard”
STAR”’
ADDENDUM
TIE communications, Inc.
8 Progress Drive, Shelton, CT 06484
Part No. 01501 DSD
Issue l-l
September 1987
Printed in U.S.A.
Page 2
Nothing contained in this handbook shall be deemed to be, and this handbook not
a warranty of, or representation with to, any of the equipment
handbook is to change without notice and TIE/communications, Inc. has no
to any updates or corrections to this handbook. TIE/communications
Inc., also reserves the right, without prior notice, to make changes equipment design or
components as it deems appropriate. No representation is made that this handbook is complete or accurate in all respects and TIE/communications, Inc. shall not be liable for any
errors or omissions. In no event shall TIE/communications. Inc. be liable for any incidental
or consequential damages in connection with the use of this handbook. This document con-
tains proprietary information that is
of this document may be
TIE/communications, Inc.
protected
by copyright. All rights reserved. No part
or reproduced without the prior
written
consent of
01986 by TIE/communications, Inc. All Rights Reserved.
Data Star is a trademark of TIE/communications, Inc.
Page 3
OUTSIDE CALLS
VOICE CALL:
PLACE
Lift handset. Dial access code for
outside line or press a line key.
Dial telephone number.
DOWN
DIP SWITCH
ANSWER
DATA CALL:
PLACE
ANSWER (DATA
ORIGINATED CALL)
ANSWER (VOICE
ORIGINATED CALL)
Lift handset. Press flashing line
key if necessary.
Press data key. Dial access code
for an outside line or press a line
key. Dial telephone number. Dial
* for a BAUD rate of 1200.
(300 BAUD is used if a
not dialed.)
No action is required
Lift handset. Press flashing line
key if necessary. Press data key.
is
8
1
Page 4
INTERCOM CALLS
SWITCH SETTINGS,
VOICE CALL:
PLACE (RINGING)
(VOICE)
ANSWER (RINGING)
(VOICE)
DATA CALL:
PLACE (DATA
ORIGINATED CALL)
PLACE (VOICE
ORIGINATED CALL
ANSWER (DATA
ORIGINATED CALL)
ANSWER (VOICE
ORIGINATED CALL)
Lift handset. Dial extension
number.
Lift handset. Press VOICE CALL.
Dial extension number.
Lift handset.
Voice reply (if programming
permits)
or
Lift handset.
Press data key. Dial extension
number.
Lift handset. Dial extension
number. When called party
answers, either party must press
data key. Hang up.
No action is required.
Voice reply (if programming
permits)
or
Lift handset. Either party must
press data key. Hang up.
SWITCH
2 ECHO
3
9
10
NAME
NON-INTERACTIVE
INTERACTIVE
RS-232-C CONTROLS ENABLE DISABLED
BAUD RATE (1 STOP BIT)
PARITY
DTR LOW DISCONNECT
BREAK DISCONNECT DISABLED
NON-INTERACTIVE MODE
ENABLED, INTERACTIVE
MODE DISABLED
U INTERACTIVE MODE AND
NON-INTERACTIVE MODE
ENABLED.
ON
U OFF
U ENABLED
SETTING
DDD
DDU
D UD 1200
DUU
UDD
UDU
UUD
uuu
SETTING
DD
DU
U D TRANSPARENT,
uu
DISABLED
U ENABLED
U ENABLED
SETTINGS
RATE
SLAVE
300
1800
2400
4800
9600
19,200
PARITY
EVEN, 7 BITS
ODD, 7 BITS
8 BITS, NO
PARITY
NOT DEFINED
2
7
Page 5
SPEED DIAL
SIMULTANEOUS VOICE/DATA CALLS
INDIVIDUAL:
PROGRAM
PLACE
SYSTEM:
PLACE
Lift handset. Dial
programmable key designated
for SPEED DIAL or dial a
digit code. Dial outside line code
or press line key. Dial telephone
number up to 16 digits in length
including pauses (entered by
pressing
Lift handset. Dial SPEED DIAL
code
Press data key.
code
Press key that is programmed as
a SPEED DIAL key.
Lift handset. Dial SPEED DIAL
code
Press data key.
code.
Press a
SPEED DIAL
or
SPEED DIAL
VOICE CALL (WHILE ON DATA CALL):
.
PLACE Place Intercom or outside call in
ANSWER
DATA CALL (WHILE ON VOICE CALL):
PLACE Put present call on HOLD. Hang
ANSWER (VOICE
ORIGINATED CALL)
ANSWER (DATA
ORIGINATED CALL)
normal manner
Answer Intercom or outside call in
normal manner
up. Place data call in normal
manner When data call is
established, return to call on
HOLD.
Put present call on HOLD.
Answer incoming data call in
normal manner. When data call is
established, return to call on
HOLD.
No action is required
Page 6
CALL WAITING (CAMP-ON)
CALL BACK/LINE QUEUING
PLACE Upon busy signal, dial “2”. Do
not hang up. Call is completed
when called party becomes
available.
,
PLACE Upon busy signal, dial After
dial tone is heard, hang up. CALL
BACK is signified by a long ring.
Upon CALL
Calls are automatically completed
if any of the following are used:
LEAST COST ROUTING, SPEED
DIALING, LAST NUMBER
REDIAL, OR SAVE NUMBER
REDIAL. All calls, either voice or
data, are treated as voice calls
upon call back. Voice calls can
be converted to data calls at this
time, however.
handset.
Loading...