Tianjin Tiandy Digital Technology TIANDY PTZ User Manual
IR Speed Dome Camera
User’s Manual
CONTENTS
Chapter 1 Precautions .................................................................................. 3
Chapter 2 Structure ........................................................................................ 5
Chapter 3 Dome Settings ............................................................................. 7
Chapter 4 Installation Guide .................................................................... 10
Chapter 5 Functions Description .......................................................... 13
5．1 Features ......................................................................................... 13
5．2 Function Instruction ................................................................. 14
Chapter 6 Operation instruction ........................................................... 18
Chapter 1 Precautions
● Please read this manual carefully before installation.
● Handle with care
In transportation and storage process, we need to prevent stress, such as
severe vibration, and immersion to avoid any damage to the product. This
product must be carried disassembled and packaged, either in delivery to users
or in return delivery to the factory for repairing. Damage caused by assembled
transportation will not be covered by warranty.
● Install with care
Handle the product carefully and gently. Prevent such incorrect operations as
stress, severe vibration, or may lead to mechanical failure, affecting the overall
performance of product;
Under the cover are advanced optical devices, avoid direct hand touch, for the
sake of image quality;
The electrical installation must comply with safety standards, with use of
dedicated power adapter;
Control signals and video signals should maintain a sufficient distance from
high-voltage equipment or cables in the transmission process, if necessary, take
anti-lightning, anti-surge and other protective measures. Keep power off until the
completion of all installation.
● Do not dismantle parts
Do not dismantle internal parts, please turn to qualified maintenance
professionals to carry out repairs.
● Do not put any object into the product
Make sure that there is no metal object or flammable materials inside the
product. Such objects or materials may lead to fire, short circuit or damage. If
water or liquid flow into the product, turn off the power and disconnect the
power cord immediately, and then negotiate with the company. Be careful to
protect the camera. Avoid the rain, sea erosion.
● Keep the product away from electric or magnetic fields
If the product is placed near TV, radio transmitters, electromagnetic devices,
electric motors, transformers, loudspeakers in the vicinity, the electromagnetic
fields generated by them would interfere the image.
● Do not point the camera at strong light
Regardless of power on/off status, do not point the camera at the sun or very
bright objects, do not point the camera at bright stationary objects for a long time,
otherwise it will cause unrecoverable damage to the camera CCD.
● Maintenance with care
It is advised to avoid collision or vibration. Do not use strong or abrasive
detergents to clean the dome body. When cleaning up dirt, use dry cloth. if dirt is
uneasy to remove, swab with a neutral detergent. If there is sticky dust on the lens,
please use the special lens paper.
● Working Environment
Power AC 100~240V/0.5A
Communication port RS485
Environmental temperature －25～50℃（IR off） －25～30℃（IR on）
Moisture <95％（Non-condensing）
Atmospheric pressure 86～106KPa
Note: make sure outdoor installation meets water-proof requirements.
● Camera Module Specification
Items
TC-D2636L-IRWI-T
Zoom Camera
FCB-CX1020
Image Sensor
1/4” EX-View HAD CCD
Picture
Elements
NTSC:768(H)x494(V)/PAL:752(H)x582(V)
Resolution
550TV Line
Video Output
1Vp-p Composite Video(75Ω)
SYNC System
Internal/External (V-Lock)
Zoom
36X Optical, 12X Digital
S/N Ratio
50dB
Mini.
Illumination
0.01Lux ICR On
White Balance
ATW/Indoor/Outdoor/Manual/AWB/One
Push WB
Gain
Auto/Manual
Chapter 2 Structure
Housing
Camera
Dial Switch
IR Led
Front view Side view
Chapter 3 Dome Settings
Protocol Setting
This product supports two protocols: PELCO-P、PELCO-D, and two baud rate:
9600BPS, 4800BPS, 2400BPS. Protocol dip switch is bit 1~3 of SW2.
Baud Rate Setting
Baud rate setting dip switch is bit 4~5 of SW2.
Dome Address Setting
8-bit dip switch （SW1）at dome side is for setting dome address. Dome setting
adopts binary system, the 8th bit is the highest, the 1st bit is the lowest. Total 255
dome addresses could be set.。
Dome address code table under protocol PELCO-P:
Dome address code table under protocol PELCO-D：
*Notice: 1. “1” means “on” status and “0” means “off” status.
2. Dip switch for protocol PELCO-P are the same, while dip switch for PELCO-D
is slightly different. PELCO_D protocol supports maximum 254 dome addresses.
Chapter 4 Installation Guide
1、Take out the bracket and unscrew the power box from the bracket.
2、Thread cables across the bracket and connect them to the circuit board in the
power box.
Install the dome body to the bracket, screw up with 4 inner hexagon screws. If
necessary, apply water-proof glue to the joint gap.
3、unscrew the cover with the mark “SET”, set communication protocol and
addresses. Screw up again with care to avoid water.After the installation of dome
body, use two outer hexagon screws to tighten
bracket and power box.
4、Attach the drill positioning paste to the wall, and drill according to the paste,
and install expansion bolts.
5、Install the dome body together with bracket and power box to the expansion
bolts, and tighten with screws.
6、Remove two screws from the power box, and open it.
Thread power cable（AC220V）through the water-proof head on the left, and
RS485 and video cable through the water-proof head on the right.
Connect cables to the circuit board, double check order of connection to avoid
damage from wrong connection.
After cable connection, tighten the two heads, if necessary, appl water-proof
glue to the heads.
7、close power box, tighten the bracket to the power box. Double check if there is
joint gaps, if necessary, apply water-proof glue.
Chapter 5 Functions Description
5．1 Features
1. Built-in Decoder
● Power-off protection, no data loss
● Support both Chinese and English menu
● Support one week and eight hours each day timing operation
● Exact time display
● Built-in direction display function
● 220 programmable presets
● 8 cruising tracks, each cruising track has 32 preset positions
● 8 auto scan tracks, the left and right boundaries an scan speed can be set
● 8 privacy zones
● 4 pattern tours, each one with 180s memory
● 3D location function
● Guard location, the dome can operate preset, auto scan, cruising and pattern
tours functions after a short pause
● Support PELCO_P、PELCO_D protocols
● RS-485 bus
● Remote reset function
2. Integrated Universal Speed Change Rotator
● Delicate stepping motor, stable, sensitive and accurate
● 360°continuous pan without blind area
● Stepless speed change, auto zoom/speed matching
● Auto overturn function
● Manual Speed：0.01°～120°/s，Max cruising speed 120°/s
3. Built-in High Definition Day/Night Camera
● Auto iris, auto back light compensation
● Auto/manual white balance
● Auto/manual focus
● Auto/manual brightness control
● Multiple kinds of camera for options
4. All-weather Outdoor Design
● Built-in heater
● Built-in fan, can operate in 60℃
● High Die-cast Aluminum Construction
● IP66 water proof
● 3000V lightning and surge current proof
5．2 Function Instruction
● Menu Function
Support Chinese and English menu operation
● Dome Address Setting
Support up to 256 dome addresses, and dome can be controlled by the order in
same address. The address can be set by the dial switch on decoder board.
● Privacy Protection Function
Set black areas to mask the privacy or security parts. The black areas location
can be set, and support up to 8 mask zones.
● Timing Running Function
Users can set speed dome operation task at different time during one week.
Loading...