How it Works
Tiandy
Loading...
IP Speed Dome
Camera User Manual
87 pgs2.86 Mb0

Tiandy IP Speed Dome Camera User Manual

Download
Page 1
High Definition Intelligent IR
IP Speed Dome Camera
User’s Manual
Page 2
Content
Page 3
Chapter 1 Precautions
● Please read this manual carefully before installation. Note: the speed dome uses AC/DC24V power supply, and take out the dome body with power on is not allowed.
● Handle with care In transportation and storage process, we need to prevent stress, such as severe vibration, and immersion to avoid any damage to the product. This product must be carried disassembled and packaged, either in delivery to users or in return delivery to the factory for repairing. Damage caused by assembled transportation will not be covered by warranty.
● Install with care Handle the product carefully and gently. Prevent such incorrect operations as stress, severe vibration, or may lead to mechanical failure, affecting the overall performance of product; the electrical installation must comply with safety standards, with use of dedicated power adapter; Under the cover are advanced optical devices, avoid direct hand touch, for the sake of image quality; Control signals and video signals should maintain a sufficient distance from high-voltage equipment or cables in the transmission process, if necessary, take anti-lightning, anti-surge and other protective measures. Keep power off until the completion of all installation.
● Do not dismantle parts Do not dismantle internal parts, please turn to qualified maintenance professionals to carry out repairs.
● Keep the product away from electric or magnetic fields If the product is placed near TV, radio transmitters, electromagnetic devices, electric motors, transformers, loudspeakers in the vicinity, the electromagnetic fields generated by them would interfere the image.
●Do not point the camera at strong light Regardless of power on/off status, do not point the camera at the sun or very bright objects, do not point the camera at bright stationary objects for a long time, otherwise it
Page 4
will cause unrecoverable damage to the camera CCD.
● Maintenance with care It is advised to avoid collision or vibration. Do not use strong or abrasive detergents to clean the dome body. When cleaning up dirt, use dry cloth. If dirt is uneasy to remove, swab with a neutral detergent. If there is sticky dust on the lens, please use the special lens paper.
●Working Environment
Speed Dome
Environmental temperature
-40℃～+60℃
Moisture
<95%（Non-condensing）
Atmospheric pressure
86～106KPa
Power
AC/DC 24V/3.0A
Note: make sure outdoor installation meets water-proof requirements
Page 5
Chapter 2 Structure
Front view Side view
Page 6
Chapter 3 Functions Description
3.1 Features
1. Built-in Decoder
● 1.3M HD IP Speed Dome（18x）support 720P 25/30fps output.
● 1.3M HD IP Speed Dome（30x）support 720P 25/30fps output.
● 2M HD IP Speed Dome（20x）support 1080P 25/30fps output.
● Support English menu
● Power-off protection, no data loss
● RJ-45 port network port
● Support PELCO_P、PELCO_D protocols。
● Support 3D location
● 220 programmable presets
● 8 cruising tracks, each cruising track has 32 preset positions
● 8 auto scan tracks, the left and right boundaries and scan speed can be set
● 8 privacy zones
● Support OSD, date and time display
● Support 8 channel alarm input and 2 channel alarm output
● Support TF storage and local capture
2. Integrated Universal Speed Change Rotator
● Manual Speed：0.1°～200°/s，Max speed 400°/s
● 360° continuous pan rotation, tilt -11°~90° auto flip
● Stepless speed change, auto zoom/speed matching
● Classic double bearing structure, more stable operation
● Delicate stepping motor, stable, sensitive and accurate
3. All-weather Outdoor Design
● Built-in heater
● Double housing structure
● IP66 water proof
Page 7
3.2 Function Instruction
● Focus/Rotate Auto Match Speed Dome can auto adjust pan and tilt rotation speed depending on the focus distance.
● Preset Position Setting and Calling Preset function means the speed dome can memory current pan/tilt angel, focus, zoom, ect. When need, it can be called upon directly. Our speed dome support up to 220 preset positions.
● Auto Scan Users can set the left and right boundaries by control keyboard. Then speed dome can scan between it. It can set up to 8 groups scan path.
● Auto Cruising Users can program some preset positions into auto cruising sequence, then the speed dome can track as it. Each cruising tracks has 32 preset positions.
● Pattern Tour Speed Dome can memory 180s running path. When start pattern tour, speed dome can track as recording path. It supports 4 groups pattern tour.
● Guard Location The dome will rotate back to preset position after a period of vacant time.
● Power-off Protection
Speed dome can resume operation status before the power-off, no data loss.
Page 8
Chapter 4 Installation Guide
4.1 Preparation
1. Tools:
Please prepare the necessary tools according to specific situations
2. Check installation space and address Check the space is enough to install the speed dome. The wall must be thick enough to
install the expansion screws and can bear 4 times the weight of the dome camera itself.
3. Please well keep the whole package After open the package, please well keep them in case need to return to manufacturer
if any problem. ★Note：The non-original package may lead to damage during the transportation.
4.2 Installation
The speed dome supports four types installation as following：
Page 9
1：Wall mount and dimension:
Ø45
109
85
139
163
Ø9
258
Wall Mount Bracket Dimension
2：Pedant mount and dimension:
Ø45
Ø118
Ø90
Ø9
236
Pedant Mount Bracket Dimension
Page 10
3：External corner and dimension
85
139
164
104
120
M8
176
External Corner Bracket and Dimension
4：Pole mount and dimension:
139
165
120
44
M8
Pole Mount Bracket and Dimension
Page 11
4.3 Interface Instruction
Speed Dome and Bracket Interface Dimension
Page 12
Speed Dome and Bracket Interface Perspective Picture
4.4 Installation Procedures
（Take Wall Mount as Example）
1. Install bracket with firmware
Page 13
2、Lock the screws
3. Select the installation position and make circles positioning.
4. Punch on the positioning
Page 14
5. Fixed tube expanding screw
6. Connect with speed dome
7. Lock the carabiner and screws
Page 15
4.5 External Cable Connection Instruction
The speed dome adopted 800mm lead wire, including: power, control (Internet), audio input, audio output, video, alarm input, alarm output and RS485 cables, and RS485 is reversed cable. Connection interface and cable colors are as following:
Video Cable： BNC video cable can connect with monitor or other analog video devices; Control Cable：Connect computer or other devices;
Page 16
Power Cable：AC/DC24V; RS485：485AB is reversed cable; Audio Cable： Audio input and output can connect mic and speaker; Alarm Cable：Connect external alarm devices;
Note：please refer to labels on the cables
Page 17
Chapter5 Network Setup
● Operation Requirement
This system is advised to operate in the Windows XP operating system. In order to use and operate the system better, Please make sure below items setup or install correctly after this system installation.
1.Monitor resolution setup to: 1024x768 or more, color setup to Color (32 bit). Please
refer to the Windows user manual or online help.
2.Please confirm install the fonts the system need in the operating system. For
example the Chinese version system needs to install the Times New Roman font. If the system interface display abnormal, because of it maybe not install the system needed fonts or the fonts are damaged and need to reinstall the fonts.
● IE Setup
If it is the first time to use S3 series network video products, please download the ActiveX control. Before download it needs to setup the IE browser to confirm download successfully. Notice: Please use the IE browser of Windows operating system , confirm the version is above 6.0 Please don’t use any third-party browser and any IE browser shell like Maxthon, FireFox, Window of the World, we do not ensure use these software can log on the network video server
【Suggestion 1】： Use IE6、IE7
1.Open the IE browser, Click "Tools-Internet Options - Security-Internet-Custom Level"
(Figure 5.1), and set the items of ActiveX controls and plug-in to "Enable" (Figure 5.2).
Page 18
Fig. 5.1 Fig. 5.2
2.“Security-Local Internet-Custom setting”, take relative ActiveX controls and plug-ins
setting to “Enable”
3.If you use Windows XP, that would add IP address of Network Video in “trust sites” (as
figure 5.3): “trust sites”, input IP address, such as: http://192.168.1.2,and canceling “Require server verification (http:) for all sites in this zone”. Click “Add”, “close”.
Fig. 5.3
【Notice】:After finished downloading of ActiveX, returning the security setting to
“default level”
Page 19
【Suggestion 2】:Use IE8
1.Open IE, Internet Zone- Modify configuration of ActiveX in Security setting, click
“Prompt” of unsigned ActiveX as figure 5.4:
Fig. 5.4
2.Open IE8, and then log on. Please operate the ActiveX when it shows safety warning
as figure 5.5.
Fig. 5.5
3.Modify permission setting- Enable local directory path when uploading files to a server
as figure 5.6.
Page 20
Fig. 5.6
【Notice】:It is suggested that the setting above mentioned should be return to safe
level for your IE’s safety.
● System Log-on
Ensure the PC and network video equipment’s IP address in the same network segment:
etc. PC is 192.168.1.1, and network video equipment is 192.168.1.2. Open IE, inputting
the IP address in address bar. Then click “go to”, it’ll show up as figure 5.7 meantime. If it
has prompt about download the ActiveX with YES or NO, please check “YES”. After
finished the downing in few minutes, the figure 5.7 will show up
Page 21
Fig. 5.7
Input the User Name and password in the logon window on the right: Admin/1111 (correct case). It’ll link the picture after clicking “logon”. (As figure 5.8)
Fig. 5.8
【Notice】: If video cannot display correctly, it is suggested to install ActiveX as < IE Setting> for one more time.
● Device Control
It is used to control PTZ and lens, ex. PTZ direction, focus, zoom and contact closure such as light, power and rain brush output as figure5.9
Page 22
Fig. 5.9 Choose different protocol type and set device address to control different devices. Protocol（Fig 5.10）: [Protocol]: Contains the following Protocols: PTZ_PELCO_D, PTZ_PELCO_P,
PTZ_TC615_P, DOME_PELCO_D DOME_PELCO_P. [Protocol state]: Automatic identification. [Address]: You can manually enter the address of the front-end fixed point device, the
effective address range: 1 to 255. [Baud rate]: requires the user to enter the “configuration parameters "----" PTZ Settings”
interface to set up. [Set]: Set the preset position; Enter the preset number in the blank column, click "Set"
button, the camera’s current state of a preset called preset “1”; accordingly you can add
multiple preset positions. [Call]: call the preset position; Enter the preset number in the blank column, click "Call" to
call the preset position, the camera will automatically rotate to the preset position.
Fig 5.10 Fig 5.11 The lens Control and subsidiary control switch (Figure 5.11): [Zoom]: Control the camera lens zoom, optical zoom and electronic zoom. [Focus]: camera electronic focusing, use Auto Focus ineffective. [Iris]: manually control iris switch.
Page 23
Fig 5.12 Fig 5.13 PTZ control (Figure 5.12): [SPEED]: manually adjust the rotation speed of the PTZ, adjustable from 0 to 100.
Eight-way control button, control PTZ movement in eight directions, the middle button in the eight-way control button is automatically scan button, click this button, the PTZ will rotate & auto scan; click the button again, it will stop turning.
Video Parameters: (Figure 5.13): [Brightness] [Contrast] [Saturation] [Tint]: adjustable from 0 to 100
● Common parameter settings Click [General setting] to enter the General setting interface, as shown in Figure 5.14
Fig 5.14
Page 24
Common settings
[Channel Num]: the channel selection of the multi-channel network video equipment, such as: 4-channel network video server has 4 channels.
[Set video cover area]: Check to set the video occluded region, including with the mouse to take effect after the area you want to block as shown in Figure 5.15 Figure black area in the upper-right corner of the block part of the picture, click on the Clear area back to normal as shown in Fig 5.16.
Fig 5.15 Fig 5.16
Showing frame-rate and bit-stream information: select this option will display in the upper left corner of the interface, line of peach red font of frame rate and stream information in Figure 5.17
Fig 5.17 [Local storage path]: Click Browse, choose its path to be stored [Local video format]: Contains two kinds of local video format: H.264 and AVI
Page 25
Video Param (Figure 5.18)
Fig 5.18
[Video Quality: You can choose the video quality grade: best, better, good, average, poor.
Frame Rate: PAL standard, 1, 5, 10, 15, 25 frame rate are optional. Stream types: type "pure video" or "audio video” can be selected. Prefer Mode: “frame rate" and "quality" can be selected [Rate]: the bitrate size can be adjusted from 32 to 8192Kbps. Resolution: 4CIF, VGA, 720P, 960P, 1080p, etc. resolution Selectable (different models
compatible with the maximum resolution are different, supports up to 1080P). N/P MODE: Optional PAL and NTSC system. [I-frame rate: adjust the I-frame rate. Encode Mode: optional VBR, CBR system [Video encoder: optional H.264, Motion JPEG. Play Impression: low delay, high fluency Extended mode: Baseline, main profile, high profile optional.
Page 26
Audio parameters (Figure 5.19)
Fig 5.19 Audio encoder: ADPCM_DIV4, G711_A G711_U Audio Sample Rate: 8K, 32K, 48K
Video encryption (Figure 5.20)
[Encryption Type]: Contains None and AES, [Encryption password]: password required [Password Confirm]: same as above
Page 27
Fig 5.20
PTZ Setting (Figure 5.21)
Fig 5.21
[COM]: Use the serial number selection
Page 28
Baudrate: 300, 2400, 4800, 9600, 19200, 38400, 115200 common baud rate optional Check digit: no test, odd test, even test optional. Data bits: 7, 8 optional Stop bits: 1, 2 optional. Work mode: protocol mode, transparent channel optional 【Channel number: Select the channel number [COM]: Select the serial number Device type: PTZ_PELCO_D, PTZ_PELCO_P, PTZ_TC615_P, DOME_PELCO_D,
DOME_PELCO_P optional Address: selectable from 0 to 255.
Dome setting (Figure 5.22)
Fig 5.22 [Channel number]: Select an available channel. Title Type: preset, scan, cruise, pattern path, regional instructions selectable Title NO: select the title number, range 1-32 [Title Name]: enter the title name
Page 29
OSD (Figure 5.23)
Fig 5.23 Channel name: superimposed channel name can be set in English and Chinese, can be
set up to 32 English characters or 16 Chinese characters set up; does not support null character.
Superimposing type: you can choose not superimposed, date, time, channel name, date, time + channel name.
[Position]: 0 to 15 of 16 locations to choose from. Channel name position: 0 to 15 of 16 locations to choose from. [Custom coordinate]: click in video form.
Page 30
Additional characters superimposed (Figure 5.24)
Fig 5.24
Input additional characters need to superimpose in the box, by tick-defined coordinate, you can self-define the position of the additional characters.
OSD color (Figure 5.25) OSD type: channel name, date, additional character overlay. OSD color: white, black, red, green, and blue.
Page 31
Fig 5.25
Alarm settings
The motion alarm (Figure 5.26), check the "enable" box.
Fig 5.26
Page 32
[Channel Num]: select an existing alarm channel number in the view of the area, you can use the mouse to select the motion alarm area, otherwise defaulted full-screen; you can also drag the scroll bar to set up the sensitivity.
Arming: You can select Monday, Tuesday ... Sunday, and check the check box to set up the arming period.
[Link type]: optional linkage output, check the checkbox below, you can choose the alarm output channel.
Loss alarm (Figure 5.27), check the "enable" box.
Fig 5.27
【Channel Num】: Select the alarm channel number. Arming: You can select Monday, Tuesday ... Sunday, and check the check box to set up
the arming period. 【Link type】Optional link to PTZ. [Link channel]: select an existing linkage alarm channel. [Link PTZ Type]: optional no link, preset position, pattern tour etc. [Number]: If you set the linkage PTZ preset, cruise path etc. set up the corresponding
Page 33
number. Port alarm (Figure 5.28), check the "enable" box.
Fig 5.28 In port: Select the alarm input port number. Mode set: optional closed-circuit alarm, open circuit alarm. Out port: Select the alarm output port number. Mode set: optional closed-circuit alarm, open circuit alarm. Arming: You can select Monday, Tuesday ... Sunday, and check the check box to set up
the arming period. [Link type]: optional link out, check the checkbox below, you can choose the alarm output
channel. Cover alarm (Figure 5.29), check the "enable" box. 【Channel number】: Select the alarm channel number. Arming: You can select Monday, Tuesday ... Sunday, and check the check box to set up
the arming period.. Link type】Optional link to PTZ.
Page 34
[Link channel]: select an existing linkage alarm channel. [Link PTZ Type]: optional no link, preset position, pattern tour etc. [Number]: If you set the linkage PTZ preset, cruise path etc. set up the corresponding
number
.
Fig 5.29
Alarm Server (Figure 5.30)
[Alarm server]: set up the alarm server address [Port]: Set up the alarm server port number [COM server]: set the serial port server address [Port]: set the serial port server port number
Page 35
Fig 5.30 Email Alarm (Figure 5.31), check the "Email Alarm Enable” box.
Fig 5.31 [SMTP server]: Set the e-mail address of the SMTP server.
Page 36
[SMTP port]: Set the mail SMTP server port number. Email account: Set up e-mail login user name. [Email password: set up the email login password. Email mode: set up a email SMTP server login mode, optional off, plain, cram-md5,
digest-md5, gssapi, external, login, ntlm. [Main e-mail Address]: set up the primary address to send, also can be set up the rest of
the three email addresses. [The mail subject]: Set the theme sent.
Network parameters Wire setting (Figure 5.32)
If you want to automatically obtain IP, check “obtain an IP address automatically”,
manually enter IP set according to the actual situation.
Fig 5.32 WEB PORT (Figure 5.33) Set up WEB PORT，see Figure 5.33
Page 37
Fig 5.33
Registration Center (Figure 5.34) User name / password: the default value is QQ / QQQQ. [Server name]: The default value is NVSS-80, fill in the domain name registered on the DNS server. [IP1]: domain name server IP address. Port: fill in the default value 6004.
[UPnP]: Select “UPnP enable”, it will support UPnP port mapping and router supports
UPnP function to establish the mapping between IP and port.
Page 38
Fig
5.34
DDNS (5.35), check the "DDNS Enable" box. How to use: Login www.3322.org, register users. And add XXX.3322.org, where XXX is the name of the user-defined, mapped server used to bind the need. Enable the network video server dynamic domain name resolution, fill out the option as below: [Server domain]: fill in the domain name registration in www.3322.org XXX.3322.org. [DNS domain] Select www.3322.org server. [Port]: Server Web port. Username / Password: to fill registered user name and password. in www.3322.org. After all fill confirmed, click “Set”.
Page 39
Fig 5.35 PPPoE (Figure 5.36) Select "PPPOE Enable", fill out the required information, then click “Set”.
Fig 5.36
Page 40
FTP (Figure 5.37) FTP server url: fill in the actual FTP server address [FTP service port] fill in the corresponding server port number. Path: the path to fill in the corresponding server. [Username] : fill in the user name of the corresponding server. Password: fill in the corresponding server login password.
Picture 5.37
NTP（see picture 5.38）
【NTP server】： enter real NTP server address 【port】enter server port number 【time interval】： enter NTP time interval
Page 41
Picture 5.38
External storage SATA（see picture 5.39）
Picture 5.39
Page 42
【device no.】： select device number 【status】： display device status 【usage】： select what the disk is used for
Also you may choose part number, disk space and free space USB/SD（see picture 5.40）
Picture 5.40
【device no.】： select device number 【status】： display device status 【usage】： select what the disk is used for
Also it shows disk space and free space and initializes the disk. NFS（see picture 5.41）
【device no.】： select device number 【status】： display device status 【usage】： select what the disk is used for 【IP address】： set IP address 【mapping path】： select available mapping path
Also it shows disk space and free space
Page 43
Picture 5.41
Record policy（see picture5.42）
Picture 5.42
Including alarm record, timing record and manual record
Page 44
【channel】： select available channel number 【record status】： select suitable record status 【date selection】： set date of existing record or if select timing record you can set
recording period through that. 【disconnect record】： set if record or not in disconnection condition. Pre-recorded alarm（see picture 5.43）， activated by checking of “pre-recorded alarm”
Picture 5.43
【channel number】： select channel number 【alarm pre-record time】： selectable 5、10、15 second 【alarm post-record time】： selectable 10、15、30、60 second Storage policy（see picture 5.44） 【pack by time】： selectable 10、20、30、60 minute 【pack by size】： choose 20-200 figure（not available now） 【free disk space】： cannot be less than 200MB。 【storage policy】：select to stop record, round delete and round delete except alarm files.
Page 45
Picture 5.44
Snapshot settings（see picture 5.45）
【channel number】： select available channel number。 【timer capture】： enable timer snapshot 【interval】： set time interval of snapshot
Also can enable capture linkage by checking associated with FTP and Email
Page 46
Picture 5.45 Smart analysis Parameter settings: basic parameter（see picture 5.46）， check “enable”
Picture 5.46
Page 47
【object color】： selectable red, green, yellow, blue, purple, cyan, black and white 【alarm color】： selectable red, green, yellow, blue, purple, cyan, black and white 【track length】： set track length 【detective sensitivity】： selectable high, medium and low
Parameter settings： Event settings（see picture 5.47）， check“enable”to activate.
Picture
5.47
【rule ID】：1~8 available 【event set】： selectable tripwire, boarder protection, object left or lost detection 【identify】： selectable all, people, cars, people and cars 【none-alarm color】： selectable red, green, yellow, blue, purple, cyan, black and white 【alarm color】： selectable red, green, yellow, blue, purple, cyan, black and white
Parameter settings: alarm information settings（see picture 5.48），check “enable”to activate.
【channel number】： select video channel number 【rule ID】：selectable 1~8
Page 48
It can display the corresponding rule number and rule name, and click “reset” can delete all alarm information. You can see details in alarm information by display of alarm information.
Picture 5.48 Parameter settings：alarm settings（see picture 5.49）
Picture 5.49
Page 49
【channel number】：Select channel number 【rule ID】：selectable 1~8 rule ID，and display rule name and event. 【schedule settings】：select Monday, Tuesday…..to Sunday, check it and set time period
of schedule.
【link type】：enable to link to PTZ 【link channel】：select available linked alarm channel 【link PTZ type】：select to ignore linkage, preset, track and cruiser path 【number】： If linked PTZ type is set for preset, track and cruiser path, put number here.
Advanced option Version information（see picture 5.50）
Picture5.50
System information（see picture 5.51）
Page 50
Picture5.51
PU settings（see picture 5.52）
Picture5.52
Page 51
SIP settings（picture 5.53）
Picture5.53
Access platform （picture 5.54）
Picture5.54
Page 52
User management（see picture 5.55）
Picture5.55
【add user】： enter user name such as “guest” and password. And then select “authority” and click “add”to add a new user
【delete user】： select targeted user and click “delete” to delete this user 【change password】：Select the user you want to modify in the " User selection", enter
the new password, click on "Change Password". Update （see picture 5.56）
Page 53
Picture 5.56 You can update 2 kinds of program including .bin and .box files. Note: .bin file cannot be worked until twice updating. Log management（see picture5.57）
Picture 5.57
Page 54
Chapter 6 Menu Settings
Call #95 preset to open menu of speed dome. Menu index
MAIN MENU
-------------------------------------------
Language：English <System Information> <Display Settings> <Dome Settings> <Camera Settings> <Motion> <Help>
Exit
SYSTEM INFORMATION
-------------------------------------------
Camera Status ：OK Horizon Limit ：OK Vertical Limit ：OK Memory Status ：OK TEMP Sensor ：OK Dome TEMP ：58℃ TEMP Scale ：Celsius <Next Page> Back Exit
DISPLAY SETTINGS
-------------------------------------------
Preset Title ：5 Sec Motion Title ：5 Sec Zones Title ：5 Sec Coordinate ：5 Sec Pursuit Title ： 5 Sec Title Background ： OFF
Back Exit
DOME SETTINGS
-------------------------------------------
Auto Flip ：ON Auto Stop Time ：30Sec Menu OFF Time ：5Min Tilt Angle Set ：-5 Speed Level ：Auto <Idle Action> <IR Led Setting> <Next Page> Back Exit
CAMERA SETTINGS
-------------------------------------------
Focus Mode ：Auto Digital Zoom ：OFF Backlight ：OFF Image Freeze ：OFF Zoom Speed ：Middle Day Night ：Auto Camera Reset ：OFF <Advanced> Back Exit
MOTION
------------------------------------------­ <Preset> <Scan> <Cruise> <Pattern> <Zones> <Timing Action>
Back Exit
Page 55
Language
This speed dome provide 2 optional language including English and Chinese. You can
Call #95 preset to open menu of speed dome, and move your mouse to “language
settings”, press “aperture on” to enter settings and move joystick to switch
English/Chinese, then press “aperture on” to confirm.
System information
MAIN MENU
------------------------------------------­ Language：English <System Information> <Display Settings> <Dome Settings> <Camera Settings> <Motion> <Help>
Exit
SYSTEM INFORMATION
-------------------------------------------
Camera Status ：OK Horizon Limit ：OK Vertical Limit ：OK Memory Status ：OK TEMP Sensor ：OK Dome TEMP ：58℃ TEMP Scale ：Celsius <Next Page>
Back Exit
A B C D
E F G H
A：camera status B：horizon limit C：vertical limit D：memory status E：temperature sensor F：dome temperature G：temperature scale H：next page
SYSTEM INFORMATION
------------------------------------------­ Camera Status ：OK Horizon Limit ：OK Vertical Limit ：OK Memory Status ：OK TEMP Sensor ：OK Dome TEMP ：58℃ TEMP Scale ：Celsius <Next Page> Back Exit
SYSTEM INFORMATION
------------------------------------------­Version ：V10001 Publish Date ：13-01-21 Publish Time ：16:12:12 Interface ：OK IR Led Status ：OK Wiper Limit ：OK Light Sensor ：OK
Back Exit
Page 56
Display settings
Call #95 preset to open menu and move joystick, select “display” settings”, then press
“aperture on” to enter ”display settings” sub-menu, waving the joystick to move the
pointer to targeted menu.
MAIN MENU
-------------------------------------------
Language：English <System Information> <Display Settings> <Dome Settings> <Camera Settings> <Motion> <Help>
Exit
DISPLAY SETTINGS
-------------------------------------------
Preset Title ：5 Sec Motion Title ：5 Sec Zones Title ：5 Sec Coordinate ：5 Sec Pursuit Title ： 5 Sec Title Background ： OFF
Back Exit
A B C D
E
F
A： Preset Title Press iris on to set up "preset title" and select "2S/5S/10S/LAST/OFF". Press iris on to
confirm.
B: Motion Title
Press iris on to setup "MOTION TITLE" and select "2S/5S/10S/LAST/OFF". Press iris on to confirm
C： Zones Title
Press iris on to set up "ZONES TITLE" and select "2S/5S/10S/LAST/OFF". Press iris on to confirm.
D： Coordinate
Press iris on to setup "coordinate" and select "2S/5S/10S/LAST/OFF” through moving the joystick. Press iris on to confirm.
E： Pursuit title
Press iris on to setup "Pursuit title" and select "2S/5S/10S/LAST/OFF” through moving
the joystick. Press iris on to confirm.
F： Title background
Press iris on to setup "title background" and select "ON/OFF” through moving the joystick.
Press iris on to confirm.
Page 57
Speed dome settings
Call #95 preset to open main menu, press “aperture on” to enter “speed dome
settings”.
A B
E
C D
F G
MAIN MENU
-------------------------------------------
Language：English <System Information> <Display Settings> <Dome Settings> <Camera Settings> <Motion> <Help>
Exit
DOME SETTINGS
-------------------------------------------
Auto Flip ：ON Auto Stop Time ：30Sec Menu OFF Time ：5Min Tilt Angle Set ：-5 Speed Level ：Auto <Idle Action>
<IR Led Setting> <Next Page> Back Exit
H
A：auto flip Enable auto flip function.
B：auto stop time
Automatic stop time indicates that how long the speed dome does not receive stop code to stop the PTZ action selectable 5 sec, 15 sec, 30 sec, 60 sec.
C：menu off time
In the case of open the menu, how long it will automatically turn off the menu display without any actions. Move the cursor to the menu off time, open the “aperture on” to enter the setup mode, the joystick up and down to select a menu off time 1/2/5/10 minutes"
D：tilt angle set
Select “0” degree through “-11” degree, minus degree is available.
Set interval is 1 degree. When the user finishes to set starting angle, the configuration of angle will be saved on condition of power off or resuming of factory settings.
E：speed level
There are four options for selection including auto, high speed, medium speed and low speed. You can change the max speed by reconfiguration.
F：idle action Move your pointer to “idle action” then press “aperture on” to enter submenu.
Page 58
DOME SETTINGS
------------------------------------------­ Auto Flip ：ON Auto Stop Time ：30Sec Menu OFF Time ：5Min Tilt Angle Set ：-5 Speed Level ：Auto <Idle Action> <IR Led Setting> <Next Page> Back Exit
IDLE ACTION
------------------------------------------­Time ：30Sec Action ：None
Back Exit
A1 B1
A1：idle time Selectable 30 sec/1min/5min/10min/30min，press “aperture on” to confirm.
B1：idle action
Use joystick to Select idle action, including preset 1/ scan1/ cruiser 1/ pattern1 /none
G：IR LED settings
IR LED SETTINGS
---------------------------------------------------- Control Mode ：Auto Threshold ：Standard Delay Time ：Middle Start Time ：19:00 Stop Time ：06:00 Zoom Match ：ON <Bright Set>
BACK Exit
DOME SETTINGS
-------------------------------------------
Auto Flip ：ON Auto Stop Time ：30Sec Menu OFF Time ：5Min Tilt Angle Set ：-5 Speed Level ：Auto <Idle Action> <IR Led Setting> <Next Page> Back Exit
A1 B1
C1 D1 E1 F1 G1
A1：control mode
Use joystick to select control mode including auto, auto, followed by camera, timer start, manually turn on and manually shut off. Description of five mode
1: Auto: IR is turned on or shut off completely by the light sensors control, and the speed dome force the camera to switch black and white. When the photosensitive sensor detects brightness around less than the photosensitive threshold, the infrared light will open and the camera will be forced from color to black and white. When the photosensitive sensor detects brightness around more than the photosensitive threshold, the infrared light will shut off and the camera will forced from black and white to color.
2：followed by camera: infrared light is triggered automatically by the camera color switch.
Page 59
When the ambient light is getting dark, the camera switches from color to black and white. On the contrary, when the ambient light is getting bright, camera switches from black and white to color and infrared light shut off.
3：timer start: according to customer settings of time periods to turn on and off, you can
control whether Infrared light is turned on or shut off across by 00:00. Such as: (set opening time: 19:00, set off time: 06:00). The infrared light will stay on from 9:00 to 06:00 in the next day, and shut off in the rest time.
4：manually turn on：user forces to turn on the infrared light manually. 5：manually shut off：user forces to shut off the infrared light manually.
Note: when the speed dome stays at “followed by camera” mode the switch of camera
will be disabled.
B1：sensitivity threshold
The user can adjust the environment light threshold of infrared light according to the special occasions of the site. In automatic mode, infrared light turns on in the default setting of 1 ~ 2lux brightness (there might be deviation effected by the direction of the speed dome). Move the joystick to adjust level of very low / low / standard / medium / high.
C1：delay time
When the ambient light is above / below the set sensitivity threshold, the delay time for turning on / off the infrared light can be adjustable. Press “aperture on” to set delay time and move left and right joystick to adjust low / medium / high level.
D1：start time Move left and right joystick to set clock and move up and down to set figures.
E1：stop time
Move left and right joystick to set clock and move up and down to set figures. It can be cross 00：00 for setting. Note: the setting for infrared light turn on and shut off time cannot be enabled until infrared light stay at “timer” mode.
F1：zoom match
Press “aperture on” to enter “zoom match” sub-menu. When you select “open” mode the brightness and consumption of infrared light can match with distance between camera
Page 60
and object. In different zoom folds the infrared light can be auto-controlled perfectly to
adjust consumption of infrared light. When you select “close” mode infrared light will turn
on as per what the user set brightness for each group of light without function of zoom self-adjustment. We highly recommend you to select zoom match.
G1：brightness set
A2：LED1 at long distance When shut off zoom match you can adjust LED1 at long distance brightness with level from 0~10, the more the brighter. B2：LED2 at long distance When shut off zoom match you can adjust LED2 at long distance brightness with level from 0~10, the more the brighter. C2：LED1 at close distance When shut off zoom match you can adjust LED1 at close distance brightness with level from 0~10, the more the brighter. D2：LED2 at close distance When shut off zoom match you can adjust LED2 at close distance brightness with level from 0~10, the more the brighter.
H：NEXT PAGE
Move the cursor to the "next page", press the stop on entering "next" submenu
DOME SETTINGS
------------------------------------------­ Auto Flip ：ON Auto Stop Time ：30Sec Menu OFF Time ：5Min Tilt Angle Set ：-5 Speed Level ：Auto <Idle Action> <Next Page> Back Exit
DOME SETTINGS
------------------------------------------­Temperature Mode ：Auto <Origin Set> <North Set>
Back Exit
A1 B1
C1
A1: temperature control mode Move the cursor to "temperature control", according to the aperture opening for "temperature control mode" setting, move shake bar, temperature control mode can be
Page 61
set to: air/mist/heating on/off/Auto, established in accordance with the aperture opening, set an end. B1: azimuth zero point setting Move the cursor to "set the zero point position," according to the aperture opening for "azimuth setting the zero point" setting, move shake bar, select a position zero, established in accordance with the aperture opening, set an end. C1: azimuth North set Move the cursor to "azimuth North setting" according to the aperture opening for "orientation means North setting" settings, move shake bar, select a location for the North, established in accordance with the aperture opening, set an end.
Camera settings 2 million camera settings:
A B
E
C D
F G H
MAIN MENU
------------------------------------------­ Language：English <System Information> <Display Settings> <Dome Settings> <Camera Settings> <Motion> <Help>
Exit
CAMERA SETTINGS
------------------------------------------­ Focus Mode ：Auto Digital Zoom ：OFF Backlight ：OFF Image Freeze ：OFF Zoom Speed ：Middle Day Night ：Auto Camera Reset ：OFF <Advanced> Back Exit
A. focus mode Move the cursor to "focus mode", press IRIS open to enter focus mode setting, rocker bottom for automatic and manual zoom and focus mode selection. B.Digital Zoom Move the cursor to "digital zoom", press the IRIS on entering the digital zoom setting, rocker bottom on and off settings. C.Backlight compensation Switch settings. When the image brightness of the screen low, open the brightness of the backlight compensation to improve webcam. D.Image freeze Switch settings. When you want to lock the current picture, open the image to freeze will always show the current image, until you close the image freezes again.
Page 62
E.Variable-speed Move the cursor to "zoom speed", press the aperture opening into the zoom speed setting mode, rocker arm up and down to select the camera's zoom speed, can be set to "low", "medium", "high speed". F.Day and night conversion Move the cursor to "transform day and night", press the aperture on enter conversion settings around the clock mode, rocker arm up and down to select camera night mode can be set to "auto", "color", "black and white". G． Restore factory Select camera to factory settings to "on", the system will restore the parameters to the factory settings of the camera H． Senior
A1 B1 C1
D1
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Color Settings> <Special Settings>
Back Exit
CAMERA SETTINGS
------------------------------------------­ Focus Mode ：Auto Digital Zoom ：OFF Backlight ：OFF Image Freeze ：OFF Zoom Speed ：Middle Day Night ：Auto Camera Reset ：OFF <Advanced> Back Exit
A1. white balance mode Move the cursor to "white balance mode", press the aperture opening into white balance setting mode, rocker bottom can be set separately for "/ATW/automatic/manual auto/indoor/outdoor/outdoor sodium Na Kouang auto/light/key/key mode is triggered". When the white balance mode to manual when the r, b gain value can be adjusted: move the cursor to "r gain" by IRIS on entering r-gain setting mode, rocker set r-gain value.Move the cursor to "b gain" by IRIS on entering the b gain settings mode, rocker sets b gain value。
Page 63
A1 B1
C1
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Color Settings> <Special Settings>
Back Exit
WB SETTINGS
------------------------------------------­WB Mode ：Auto Red Gain ：210 Blue Gain ：210
Back Exit
B1.Exposure mode
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Color Settings> <Special Settings>
Back Exit
EXPOSURE SETTINGS
------------------------------------------­Exposure Mode ：Auto Shutter Priority ：Auto Iris Priority ：Auto Bright Priority ：Auto Camera Gain ：-3dB CAM_ExpComp ：OFF ExpComp Gain ：-7
Back Exit
Move the cursor to "exposure mode", press the stop on entering the exposure mode set, rocker bottom can be set to "auto/priority/aperture priority/shutter priority/manual brightness" When the shutter priority exposure mode State, move the cursor to "shutter priority" by IRIS on entering setup mode, rocker set the shutter speed value. When aperture priority exposure mode State, move the cursor to "Aperture priority" by IRIS on entering setup mode, joystick up or down to set the aperture value. Brightness priority status when the exposure mode, move the cursor to "brightness priority" by IRIS on entering setup mode, rocker set the brightness values. C1. color settings
Page 64
A2 B2
C2
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Color Settings> <Special Settings>
Back Exit
COLOR SETTINGS
-------------------------------------------
Color Gain ：60% Hue Setting ：-14 Chroma Suppress ：OFF Gamma Setting ：Standard
Back Exit
D2
A2. color-gain Move the cursor to "color-gain", according to the aperture opening into the color-gain settings, and rocker color-gain is set to 60%~200%. B2. Hue settings Move the cursor to "tone settings", press the stop on entering-tone set, joystick up or down to set the tone for the -14~14 (even). C2. Chroma Suppress Move the cursor to the "Suppression of color", set the aperture opening into the color suppression, joystick up or down to set the tone for the level I, level II, and level III, closed. D2. Gamma settings Move the cursor to "Gamma settings", press the stop on entering the Gamma setting, rocker set the Gamma to level I, level II, III, IV, v-class, standard.
D1.Special setting
F2
A2 B2
C2
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Color Settings> <Special Settings>
Back Exit
SPECIAL SETTINGS
------------------------------------------­Wide Dynamic ：OFF High Sensitivity ：OFF Slow Exposure ：OFF Image Denoise ：OFF Mirror Image ：OFF Aperture Setting ： 00 Ir Correct ： OFF
Back Exit
D2
E2
G2
A2. move the cursor to the "dynamic", set the aperture opening into a wide dynamic, rocker arm up and down to select parameters, can be set to "off/on/auto" B2. Move the cursor to "high sensitivity", press the stop on entering the high sensitivity setting, rocker arm up and down to select parameters, can be set to "off/on".
Page 65
C2. Move the cursor to "slow exposure", press the stop on entering the slow exposure
settings, rocker arm up and down to select parameters, Can be set to "off level
11\10\9\8\7\6\5\4\3\2\1”。 D2. Move the cursor to "image noise", press the stop on entering the image noise
reduction settings, rocker arm up and down to select the parameter can be set to "off level 5/4/3/2/1。 E2. move the cursor to "mirror image", set the rocker as aperture opening into the image flip up and down to select parameters, can be set to "off/on". F2. Move the cursor to "aperture setting", press the stop on entering the sharpness setting, rocker arm up and down to select the parameter can be set to 00~15. G2. Move the cursor to "Ir correct", press the stop on entering IR correction settings, rocker arm up and down to select the parameter can be set to turn on/off.
1.3 million camera set (fog):
A B
E
C D
F
G
MAIN MENU
------------------------------------------­ Language：English <System Information> <Display Settings> <Dome Settings> <Camera Settings> <Motion> <Help>
Exit
CAMERA SETTINGS
------------------------------------------­ Focus Mode ：Auto Digital Zoom ：OFF Backlight ：OFF Image Freeze ：OFF Zoom Speed ：Middle Day Night ：Auto Camera Reset ：OFF <Advanced> Back Exit
A. focus mode Move the cursor to "focus mode", press IRIS open to enter focus mode setting, rocker arm upper and lower automatically, select manual mode. B. Digital Zoom Move the cursor to "Digital Zoom" and click set aperture opening into the spotlight type, rocker arm up or down close, spot light, integrated and low light settings. C. Backlight compensation Switch settings. When the image brightness of the screen low, open the brightness of the backlight compensation to improve webcam. D. Zoom speed Move the cursor to "zoom speed", according to the aperture opening into the zoom speed
Page 66
setting mode, joystick up or down to select the camera's zoom speed to be set to "low", "medium", "high speed".
E. Day and night conversion Move the cursor to "transform day and night", converted as the Aperture open access day and night setting modes, joystick up or down to select the camera for day and night mode to be set to "auto", "color", "black and white". F． Camera Restart Select camera factory-set to "open", the system will restore the camera parameters to factory settings. G． Advanced
A1 B1 C1
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Special Settings> <Aperture Settings> <Others>
Back Exit
CAMERA SETTINGS
------------------------------------------­ Focus Mode ：Auto Digital Zoom ：OFF Backlight ：OFF Image Freeze ：OFF Zoom Speed ：Middle Day Night ：Auto Camera Reset ：OFF <Advanced> Back Exit
D1
E1
A1. white balance mode Move the cursor to "white balance mode", press the aperture opening into white balance setting mode, rocker bottom can be set to "auto/manual". When the white balance mode to manual when the r, b gain value can be adjusted: move the cursor to "r gain" by IRIS on entering r-gain setting mode, rocker set r-gain value. Move the cursor to "b gain" by IRIS on entering the b gain settings mode, rocker sets b gain value.
Page 67
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Special Settings> <Aperture Settings> <Others>
Back Exit
WB SETTINGS
-------------------------------------------
WB Mode ：Auto Red Gain ：210 Blue Gain ：210
Back Exit
B1.Exposure mode
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Special Settings> <Aperture Settings> <Others>
Back Exit
EXPOSURE SETTINGS
------------------------------------------­Exposure Mode ：Auto Shutter Priority ：Auto Iris Priority ：Auto Bright Priority ：Auto
Back Exit
Move the cursor to "exposure mode", press the stop on entering the exposure mode set, rocker bottom can be set to "auto-brightness/priority/aperture priority/shutter priority" As for shutter priority exposure mode State, move the cursor to "shutter priority" by IRIS on entering setup mode, rocker set shutter value up or down. When the exposure mode to aperture priority when moving the cursor to "Aperture priority" by IRIS on entering setup mode, rocker set the aperture value. Brightness priority status when the exposure mode, move the cursor to "brightness priority" by IRIS on entering setup mode, rocker set brightness value。
C1 Special setting
Page 68
A2 B2 C2
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Special Settings> <Aperture Settings> <Others>
Back Exit
SPECIAL SETTINGS
------------------------------------------­Wide Dynamic ：OFF Digital Zoom ：OFF Image Freeze ：OFF Focus Limit ：30cm
Back Exit
D2
A2. move the cursor to the "dynamic", set the aperture opening into a wide dynamic, rocker arm up and down to select parameters, can be set to "off/open". B2. move the cursor to "digital zoom", press the IRIS on entering the digital zoom setting, rocker arm up and down to select parameters, can be set to "off/on". C2. move the cursor to "image freezing", set the aperture opening into the image to freeze, rocker arm up and down to select parameters, can be set to "off/open"。 D2. Move the cursor to "minimum focus distance", set the aperture opening into the minimum focusing distance, rocker arm up and down to select parameters, can be set to "1cm/10cm/30cm/1M/1.5M"。
D1. Aperture setting
A2 B2 C2
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Special Settings> <Aperture Settings> <Others>
Back Exit
APERTURE SETTINGS
------------------------------------------­Sharpness ：Auto Aperture_H ：32 Aperture_V ：32
Back Exit
A2. Move the cursor to "sharpness", press the stop on entering the sharpness setting, rocker arm up and down to select parameters, can be set to "auto/manual". B2. when manual is sharpening, move the cursor to "horizontal", set the aperture opening into the horizontal resolution, rocker arm up and down to select the parameter can be set to 00~64. C2. When manually is sharpening, move the cursor to "vertical resolution", set the
Page 69
aperture opening into the vertical resolution, rocker arm up and down to select the parameter can be set to 00—64 E1.Others
A2 B2
C2
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Special Settings> <Aperture Settings> <Others>
Back Exit
OTHER SETTINGS
-------------------------------------------
Defog Mode ：OFF Defog Level ：064 Elec-Stabilization ：OFF
Back Exit
A2. Move the cursor to "through the fog mode", press the stop on entering through the fog mode setting, rocker arm up and down to select parameters, can be set to "1~5-level and closed". B2. when coming through the fog mode when it is not closed, move the cursor to "fog", press the stop on entering through the fog level. C2. move the cursor to "electronic image stabilization", press IRIS open access electronic anti-shake setting, rocker arm up and down to select the parameter can be set to turn on/off.
1.3MP Camera setting：
A B
E
C D
F G
MAIN MENU
------------------------------------------­ Language：English <System Information> <Display Settings> <Dome Settings> <Camera Settings> <Motion> <Help>
Exit
CAMERA SETTINGS
------------------------------------------­ Focus Mode ：Auto Digital Zoom ：OFF Backlight ：OFF Image Freeze ：OFF Zoom Speed ：Middle Day Night ：Auto Camera Reset ：OFF <Advanced> Back Exit
A. focus mode Move the cursor to "focus mode", press IRIS open to enter focus mode setting, rocker arm upper and lower automatically, select manual mode. B. Digital Zoom Move the cursor to "Digital Zoom" and click set aperture opening into the spotlight type,
Page 70
rocker arm up or down close, spot light, integrated and low light settings. C. Backlight compensation Switch settings. When the image brightness of the screen low, open the brightness of the backlight compensation to improve webcam. D. Zoom speed Move the cursor to "zoom speed", according to the aperture opening into the zoom speed setting mode, joystick up or down to select the camera's zoom speed to be set to "low", "medium", "high speed".
E. Day and night conversion Move the cursor to "transform day and night", converted as the Aperture open access day and night setting modes, joystick up or down to select the camera for day and night mode to be set to "auto", "color", "black and white". F． Camera Restart Select camera factory-set to "open", the system will restore the camera parameters to factory settings. G． Advanced
A1 B1
C1
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Special Settings>
Back Exit
CAMERA SETTINGS
------------------------------------------­ Focus Mode ：Auto Digital Zoom ：OFF Backlight ：OFF Image Freeze ：OFF Zoom Speed ：Middle Day Night ：Auto Camera Reset ：OFF <Advanced> Back Exit
A1. white balance mode Move the cursor to "white balance mode", press the aperture opening into white balance setting mode, rocker bottom can be set to "auto/manual". When the white balance mode to manual when the r, b gain value can be adjusted: move the cursor to "r gain" by IRIS on entering r-gain setting mode, rocker set r-gain value. Move the cursor to "b gain" by IRIS on entering the b gain settings mode, rocker sets b gain value。
Page 71
A1 B1
C1
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Special Settings>
Back Exit
WB SETTINGS
------------------------------------------­WB Mode ：Auto Red Gain ：210 Blue Gain ：210
Back Exit
B1.exposuremode
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Special Settings>
Back Exit
EXPOSURE SETTINGS
------------------------------------------­Exposure Mode ：Auto Shutter Priority ：Auto Iris Priority ：Auto Bright Priority ：Auto
Back Exit
Move the cursor to "exposure mode", press the stop on entering the exposure mode set, rocker bottom can be set to "auto-brightness/priority/aperture priority/shutter priority" As for shutter priority exposure mode State, move the cursor to "shutter priority" by IRIS on entering setup mode, rocker set shutter value up or down. When the exposure mode to aperture priority when moving the cursor to "Aperture priority" by IRIS on entering setup mode, rocker set the aperture value. Brightness priority status when the exposure mode, move the cursor to "brightness priority" by IRIS on entering setup mode, rocker set the brightness values.
C1.Special settings
Page 72
A2 B2 C2
ADVANCED
------------------------------------------­<WB Settings> <Exposure Settings> <Special Settings>
Back Exit
SPECIAL SETTINGS
------------------------------------------­Wide Dynamic ：OFF Sharpness ：Auto Aperture_H ：15 Aperture_V ：15 Focus Limit ： 30cm
Back Exit
D2 E2
A2. move the cursor to the "wide dynamic", set the aperture opening into a wide dynamic, rocker arm up and down to select parameters, can be set to "off/open". B2. move the cursor to "sharpness", press the IRIS on entering the sharpness setting,
rocker arm up and down to select parameters, can be set to "off/on". C2. when manual is sharpening, move the cursor to "horizontal", set the aperture opening into the horizontal resolution, rocker arm up and down to select the parameter can be set to 00~64. D2. When manually is sharpening, move the cursor to "vertical resolution", set the aperture opening into the vertical resolution, rocker arm up and down to select the parameter can be set to 00—64 E2. Move the cursor to "minimum focus distance", set the aperture opening into the minimum focusing distance, rocker arm up and down to select parameters, can be set to "1cm/10cm/30cm/1M/1.5M"。
Motion
MAIN MENU
------------------------------------------­ Language：English <System Information> <Display Settings> <Dome Settings> <Camera Settings> <Motion> <Help>
Exit
A
B
E
C D
F
MOTION
------------------------------------------­ <Preset> <Scan> <Cruise> <Pattern> <Zones> <Timing Action>
Back Exit
A:Preset positions
Page 73
MOTION
------------------------------------------­ <Preset> <Scan> <Cruise> <Pattern> <Zones> <Timing Action>
Back Exit
PRESET
------------------------------------------­Preset Number ：001 Title Set ：PRESET01 Call <Set> Delete
Back Exit
A1 B1 C1
D1
E1
A1. Preset number Move the cursor to "preset", press the stop on entering setup mode, preset, rocker, preset up and down Settings. Ball machine supports a total of 220 preset positions, 1-64%. B1. Title set Move the cursor to "headers", press the stop on entering the preset position settings submenu, preset bit set.Note: the current title set is on the WEB. C1. call Move the cursor to "call", press the stop on call corresponds to a set of presets. D1. Set the aperture opened enter preset position setting mode, appears on the screen "press IRIS open to confirm ...".Users can operate on the dome, reaches the desired position and press the aperture set to store the current position. E1. Deleted Move the cursor to "delete", press the aperture on correspond to the preset preset number.
B: Automatic scanning
Page 74
MOTION
------------------------------------------­ <Preset> <Scan> <Cruise> <Pattern> <Zones> <Timing Action>
Back Exit
SCAN
------------------------------------------­Scan Number ：1 Title Set ：SCAN1 Start <Left Limit> <Right Limit> Scan Speed ：20
Back Exit
A1 B1 C1
D1
E1
F1
A1. Scan Number Move the cursor to "scan group number" setting mode press the IRIS on entering the scan group number, rocker arm to scan up and down group Settings. Supports 8 ball leads the Group scan path. B1. Title set Move the cursor to the "headings" title by the aperture opening into the scan path settings submenu, path header settings for scanning. Note: the current title set is on the WEB. C1. Start Move the cursor to "Start scan", press IRIS open to initiate a scan path, scan group. D1. Left Limit Move the cursor to "set the left edge" and click stop on-access scan set left border mode, appears on the screen "press IRIS open to confirm ...".Users can operate on the dome, reaches the desired position and press the aperture opened to store the current path to the location to scan to the left edge. E1. Right Limit Move the cursor to "set right" right edge press the stop on-access scan settings mode, appears on the screen "press IRIS open to confirm ...".Users can operate on the dome, reaches the desired position and press the aperture opened to store the current path to the location to scan the right border. F1. Scan speed Move the cursor to "scanning speed", press stop on-access scan speed setting mode, rocker arm upper and lower speed level set, speed 1-30 adjustable
Page 75
C：Cruise
MOTION
------------------------------------------­ <Preset> <Scan> <Cruise> <Pattern> <Zones> <Timing Action>
Back Exit
CRUISE
------------------------------------------­Cruise Number ：1 Title Set ：Cruise1 Start <Cruise Set> Delete
Back Exit
A1 B1 C1
D1
E1
A1., cruise group Move the cursor to "sweep the cruise group," press the IRIS on entering setup mode, cruise group, rocker, cruising up and down group Settings. Supports 8 ball leads a group cruise route. B1. Title settings Move the cursor to the "headings" title by the aperture opening into the cruise path settings submenu, cruising path header settings. Note: the current title set is on the WEB. C1. Start cruising Move the cursor to "start the cruise", press IRIS open to initiate a cruises group cruise path. D1. Cruise Set Move the cursor to "Edit series", press the stop on entering the cruise series Edit submenu. E1. Delete Move the cursor to "delete", press the aperture on delete cruises group cruise path.
D1:Cruise Set
Page 76
CRUISE
------------------------------------------­Cruise Number ：1 Title Set ：Cruise1 Start <Cruise Set> Delete
Back Exit
CRUISE
------------------------------------------­NO Preset Interval 01 --------- --------­02 --------- --------­03 --------- --------­04 --------- --------­05 --------- --------­06 --------- ---------
EDIT 01 001 01 INS Back Exit
Move the cursor to "editing" sequence press IRIS open to enter edit mode, rocker about selecting the Edit option. a.When the bracket is in ordinal position, add the analog stick up and down to select the preset number 1-32. b.When the angle brackets is preset position, rocker arm up and down to select the corresponding preset position of the serial number you need to add. c.When the bracket is in the right time, rocker arm up and down to select the edit status, namely, "insert", "OK", "delete". In the "insert" State by aperture space, the sets the ordinal position of the current record will be inserted, after this record will move down in turn. "OK" State press the aperture on the key, the current record set by ordinal location record will be overwritten. In the "deleted" State by aperture space, sets the ordinal position of the record will be deleted. Sequence press the stop key to exit the edit mode.
Page 77
D:Pattern
MOTION
------------------------------------------­ <Preset> <Scan> <Cruise> <Pattern> <Zones> <Timing Action>
Back Exit
PATTERN
------------------------------------------­Pattern Number ：001 Title Set ：PATTERN 1 Start <Set> Delete
Back Exit
A1 B1 C1
D1
E1
A1. mode path group Move the cursor to "mode path group number" in Aperture opening into the path group setting mode, rocker mode path group, setting up or down. Ball machine total supporting 8 pattern path. B1. Title settings Move the cursor to the "headings" title by the IRIS on entering mode path settings submenu, mode path header settings. Note: the current title set is on the WEB. C1. startup path. Move the cursor to "start mode path" by IRIS on path to initiate a pattern group number mode path. D1. set Move the cursor to "set", in Aperture opening into the set mode, users can operate on the machine and ball machine will record user actions, users press the aperture on the key end mode path is set, at the same time if the progress bar when the expiration time or record to (dome records of maximum support for 180 seconds), the mode and path settings will automatically end. E1. Delete Move the cursor to "delete", by IRIS on path group deletes the corresponding mode number mode path.
Page 78
E:Zones
MOTION
------------------------------------------­ <Preset> <Scan> <Cruise> <Pattern> <Zones> <Timing Action>
Back Exit
ZONES
------------------------------------------­—Zone is not set— Zone Number ： 1 Title Set ：ZONE 1 <Left Limit> <Right Limit> Delete
Back Exit
A1 B1 C1
D1
E1 F1
Timed run: refers to a user-specified time periods, perform pre-programmed functions, such as preset, the cruise path path, mode, and scan. A1. region indicate state information. B1. regional group number Move the cursor to "regional groups" aperture setting mode, open access to regional groups, sets, rocker bottom for regional groups. Dome area indicates the total supporting 8 group. C1. Title settings Move the cursor to "headers", as the Aperture open access to regional direct title settings submenu, zone indicates that the title is set. Note: the current title set is on the WEB. D1. Set the left border Move the cursor to "set the left edge" by aperture space into regions indicates that left border setting mode, appears on the screen "press IRIS open to confirm ...".Users can operate on the dome, reaches the desired position and press IRIS open-storing the current location for the area indicates that left border. E1. Set right margin Move the cursor to "set right", press the stop key to enter the area indicates that open borders to set mode, appears on the screen "press IRIS open to confirm ...".Users can operate on the dome, reaches the desired position and press stop key stores the current location for the area indicates that open borders. F1. Delete Move the cursor to "delete", press the aperture on corresponds to a region, regional groups.
Page 79
F:Timing Action
A1 B1 C1 D1
TIMING ACTION
-----------------------------------------------------­ NO Starttime Stoptime Motion 1 00:00 00：00 NONE
2 00:00 00：00 NONE 3 00:00 00：00 NONE 4 00:00 00：00 NONE 5 00:00 00：00 NONE 6 00:00 00：00 NONE 7 00:00 00：00 NONE 8 00:00 00：00 NONE Tuesday : OFF Copy Back
MOTION
------------------------------------------­ <Preset> <Scan> <Cruise> <Pattern> <Zones> <Timing Action>
Back Exit
H1 G1 F1
Timed run: refers to a user-specified time periods, perform pre-programmed functions, such as preset, the cruise path path, mode, and scan. Move the cursor to the desired setting, press IRIS open enter the time setting mode, editing in the joystick left and right to select the desired start time, end time, linkage function, respectively.Rocker bottom to edit the current content, press IRIS open to confirm settings. A1. Timing function is divided into 7 days a week, can be set to 8 hours a day, joint action can be set separately for each period: no action, preset, scan, 1-8, cent, mode path 1-4 the cruise path. B1. start time Set current time, start time of a specified function is executed under. C1. end time Set during the current session, the end time of a specified function is executed under. D1. linkage function Sets the current function performed within the time period, can be set to: no action, preset, scan, 1-8, cent, mode path 1-4 the cruise path. E1: the timed run state control Move the cursor to this bar, press IRIS open to "on/off" setting, to enable timed run to open and close function。
Page 80
F1: week settings By IRIS on entering setup mode, rocker arm up and down to select: "Monday" ~ "Sunday". G1: timed run set up replication function 7 days a week, can be set separately, or you can just set "Monday", other dates through this feature to copy them one by one, so as to achieve flexible and efficient input methods. H1: move the cursor to this, Aperture opening you up one level. Notes: Time overlap settings do not allow the various periods of time, and does not allow time period spans 00:00.Run when you run the function by the guards, if the scheduled time is up, you interrupt the currently running and scheduled runs function.During a scheduled run time period, user action machine, will interrupt a timed run feature, such as no action within a specified time, and timing function at the current time period, scheduled runs function again.
Help
MAIN MENU
------------------------------------------­ Language：English <System Information> <Display Settings> <Dome Settings> <Camera Settings> <Motion> <Help>
Exit
MENU ORERATION HELP
-------------------------------------------
1.Call preset 95 to open menu
2.Move joystick to select item
3.Iris open to enter edit mode
4.Move joystick to edit parameter
5.Focus to control L/R direction
6.Iris open to confirm
7.Iris close to cancel
Back Exit
Aperture opened to display help information about the menu.
Page 81
Chapter 7 Specifications
Power supply
DC/AC 24V±10%
Power consumption
50W
Manual speed
0.1°～200°（Continuously variable）
Preset accuracy
±0.1°（Typical）
Decoder
Built-in
Synchronization mode
Internal sync
Auto scan
8
Auto tour
8
Pattern
Learning path to 180 seconds
Motor
High accuracy stepping motor
Focus speed automatic matching function
Control of speed automatically according to the focal length adjustment
Automatic horizontal scan
360°Can be set
Horizontal rotation angle
360°endless
Vertical rotation angle
-11°-- +90°
Control mode
Network control
Baud rate
2400/4800/9600/115200 BPS
Heater
Heater starts automatically
Working temperature
-40℃～+60℃
Working humidity
0～95%(No condensation)
Page 82
Chapter 8 Simple Problem-solving Methods
symptom
Possible causes
Solutions
Power on no action,
Power supply is damaged or not enough power
Replace the power supply
No images,
Power cable fault
Corrected
Machine is not self checking
Line problems
Troubleshoot line
Self action properly,
Network parameters are not set correctly, no networking
Ping the IP pathway is normal for the device to ensure that fall within IP and control devices on the same network segment
But no video
Network plugin settings are not correct
References the fifth chapter ' network settings ' section correctly install plug-in
Camera is damaged
Replace the camera
Image is not stable
Not enough power
Replace the power supply
machine out of control
Self test abnormal
On the back
Page 83
Chapter 9 After-sales Service
The HD Network IR speed dome products, the company offers one-year warranty. Product warranty, the company provides a free service, but if any of the following circumstances, is charged fee for material costs work: Do not operate in accordance with the provisions of the manual speed ball damage caused by a case of the Lightning strikes, fires and irresistible natural disasters; Matching problems arising from poor design to other manufacturers products cause damage; Company statement As we continue to introduce new technologies and product specifications are subject to change without prior notice.
Page 84
Appendix I Lightning and Surge
Outdoor Dome Camera need to consider lightening, anti-surge, on the premise of ensuring electrical safety, may take the following measures：
Signal transmission lines and high voltage equipment or high voltage cables must be
at least 50 meters distance between；
Try to choose outdoor wiring along the eaves line； For open field must be sealed steel tubes buried cabling, grounding and steel pipe,
the absolute prohibition of the use of overhead wiring；
In areas of severe thunderstorm or high-voltage area (such as high-voltage
substations), lightning protection equipment, as well as for additional installed power must be taken measures such as installing lightning rods
Outdoor lightning protection and grounding design of devices and circuits must be
combined with building mine requires unified consideration and in accordance with the requirements of the relevant national standards, industry standards；
System must be equipotential earthing.Earthing system anti-interference must be
met and the dual requirements of electrical safety, and shall not be mixed with strong power network neutral wire shorted or.Separately when grounding, grounding impedance less than 4 ohms, ground wire cut-area must be not greater than 25mm2 lines shorted
Page 85
Appendix II:：Hoisting construction Guide
Page 86
Page 87
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use