THUNDER TIGER Agusta A 119 Koala Assembly Manual

JK6053

This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.

It does not cover any damage caused by use or modification. The warranty does not extend

beyond the product itself and is limited only to the original cost of the kit. By the act of building this

user-assembled kit, the user accepts all resulting in liability for damage caused by the final

product. If the buyer is not prepared to accept this liability, it can be returned new and unused to

the place of purchase for a refund.

Warranty

Notice: Adult Supervision Required

This is not a toy. Assembly and flying of this product requires adult supervision.

Read through this book completely and become familiar with the assembly and flight of this A119.

Inspect all parts for completeness and damage. Browse www.thundertiger.com for customer

service if you encounter any problems.

No.3843

MEMO

16

Assembly Manual

Specifications:

Fuselage Length (less rotor): 57-1/4”(1450mm)
Fuselage Width (less rotor): 13”(330mm)
Fuselage Height: 18-1/4”(465mm)
Full-Equipped Weight: 8.38 lbs (3800g)

1

Before beginning the assembly read the instructions thoroughly to give an understanding of the sequence of steps and a
general awareness of the recommended assembly procedures.
By following these instructions carefully and referring to the corresponding pictures, the assembly of your model will be
both enjoyable and rewarding. The result will be a well built, easy to assemble scale model, which you will be proud to
display.
This A119 is designed for intermediate to advanced pilots, and this manual assumes a basic knowledge of R/C model
construction.

PRE-ASSEMBLY NOTES

1. Before you start to assemble this fuselage on your helicopter, we suggest you to first fine tune your helicopter in the air.

2. Double-check all screws, then secure and Loctite all the loose screws.

3. The instruction manual is written for Raptor 50 Titan, if user should choose to install it on other branded helicopters, we
would suggest you to study the manual thoroughly and see how it installed on a Raptor 50 Titan.
Before you begin, check the entire contents of your kit against the parts list and photos to make sure that no parts are
missing or damaged. This will also help you to become familiar with each component of your model. If you find that any of
the parts are either missing or damaged, please contact your local Thunder Tiger authorized distributors for replacements.
Neither your dealer nor Thunder Tiger authorized distributor can accept kits for return if construction has begun.
Trial fit each part before gluing it in place. Make sure you are using the correct part and that it fits well before assembling.

BEFORE YOUR ASSEMBLY

TABLE OF CONTENTS

Introduction....................................................................................................................................................2

Recommended Tools & Materials......................................................................................................................3

Item You May Need..........................................................................................................................................3

Parts Drawings.............................................................................................................................................4-5

Parts Check List..............................................................................................................................................6

Assembly...................................................................................................................................................7-15

MEMO..........................................................................................................................................................16

2

Congratulations on the purchase of our finest scale heli fuselage to date. This famous A119 fits Thunder Tiger Raptor 50,
the light fuselage comes factory pre-painted with all necessary hardware. It is very easy to assemble and only takes you
few hours of enjoyable installation to put this scale body on your helicopter. This replica A119 is just like a real thing,
hovering this 119 that will definitely make you stand out on the flying field.

INTRODUCTION

PRE-ASSEMBLY NOTES

R/C System:

6 Channel Heli radio req'd
GYRO system req'd

Helicopter:

Raptor 50 Titan Suggested

TTR4853 - Raptor 50 Titan

3

Adhesives:

Instant setting Cyanoacrylate adhesive (thin CA)
Slow setting Cyanoacrylate adhesive (thick CA)
5 Minute Epoxy (fast)20~30 Minute Epoxy(slow)

RECOMMENDED TOOLS & MATERIALS

Tools:

Model Knife, 1/2" MASK Tape, Small & Medium Screw­drivers, Scissors, Long nose Pliers, Drill and Drill Bits
(1/16", 5/64", 1/8"), 150 Grid Sand Paper, Rat Tail and
half- round file, Fine Felt Tip Pen & Soft Lead Pencil,
Reamer, Hex Wrenches.

You will need two types of adhesives for the A119, Epoxy
and Instant (cyanoacrylate) adhesives. We recommend
that you purchase both 5-minute and 30-minute epoxy to
cut down on assembly time, but you can get by with only
30-minute epoxy if time is not important. You will also
need a small bottle of both "Thick" and "Thin" instant CA
adhesive.

Model assembly can be much easier if the proper tools
are used. Therefore, we have included in our checklist
to the left, a complete listing of all the tools we used to
assemble our prototype models.

ITEMS YOU MAY NEED

3

No.1114 ,No.1114-Y

Exhaust Diverter,10MM

No.AT6078
Remote Glow Plug Extension Wire

No.2980
4-cell 3600mAh Battery

No.1115 - Precision Fueler Valve

3X10mm

Setscrew(2)

PV6059 Hardware

Front Fuselage(1)

Rear Fuselage(1)

Tie Band(2)

2X5mm

Wood Screw(32)

Screen (M/2)

Tail Boom

Foam Retainer(1)Screen (L/1)

Tail Skid(1)

Wind Shield(L/1,R/1)

Middle

Window(L/1,R/1) Sun Roof (L/1,R/1)

Front

Window(L/1,R/1)

Rear

Window(L/1,R/1)

Front Lower

Window(L/1,R/1)

PV6060 Windshield

Foot Step

Support (4)

Pitot Tube(1)Wiper (2)Foot Step (1)

Cap(4)

Decal(1)

PV6065 Decal

Wiper

Mount (2)

2x6mm Screw (2)M2 Nut (2)

Retaining

Collar (17)

Wood Mount (1)

PV6057 Fuselage

54

PARTS DRAWINGS PARTS DRAWINGS

Top Fuselage(1)

Screen (S/1)

Wiper Base (2)

PANTONE 871 C

JK 6052

Tail End(1)Horizontal Tail (L/1,R/1)

PV6058 Horizontal Tail

Exhaust Pipe (L/1,R/1)

PV6064 Integrated Wood MNT

Skid Pipe (2)

Brace A (1)

Brace B (1)

H/F Antenna (1)

Skid Joiner (4)

3x3mm

Set Screw (8)

Skid Pipe

End Cap (4)

3x18mm

Wood Screw (8)

M3 Locknut (4) M3 Washer (8)

POM

Washer (4)

3x18mm

Socket Screw (4)

PV6062 Retaining Set

Post(2) Body Retainer(L/1,R/1)

3x8mm

Socket Screw (6) M3 Washer (10)M3 Locknut ( )4

PV6063 Landing Skid

Mounting Strap (4) Silicon Tube (1)

L/F Antenna(2)

PV6061 Decoration Set