Thunderbolt FL-200 Instruction Manual

MOVING HEAD BEAM THUNDERBOLT FL-200

Instruction Manual

www.flash-butrym.pl

Content

1. Instruction----------------------------------------------------------------------------------------------------------------------------2

1.1 Application According to Purpose---------------------------------------------------------------------------------------------------------------------2

1.2 Safety and Maintenance----------------------------------------------------------------------------------------------------------------------------------2

1.3 Safety operation---------------------------------------------------------------------------------------------------------------------------------------------2

2. Lamp-----------------------------------------------------------------------------------------------------------------------------------3

2.1Replacing the lamp----------------------------------------------------------------------------------------------------------- ------------------------------3

3. Supply Voltages, Mains Cord and Connection to Mains-------------------------------------------------- ------------------------------3

4 Housing---------------------------------------------------------------------------------------------------------------------------------4

5 Operating Environment-----------------------------------------------------------------------------------------------------------5

6. Installation---------------------------------------------------------------------------------------------------------------------------5

7. Operation-----------------------------------------------------------------------------------------------------------------------------6

7.1 Controls-----------------------------------------------------------------------------------------------------------------------------6

7.2 Navigation in the Menu------------------------------------------------------------------------------------------------------------6

7.3 DMX Protocol-----------------------------------------------------------------------------------------------------------------------7

8. Fuse-------------------------------------------------------------------------------------------------------------------------------------9

9. Maintenance and cleaning-------------------------------------------------------------------------------------------------------9

10. Technical information---------------------------------------------------------------------------------------------------------10

Please read this manual carefully before operating the products.

Information under this manual subjects to update without prior advice.

More information, please visit our website: www.flash-butrym.pl.

www.flash-butrym.pl

Congratulations on purchasing this Beam 190

Thank you for extending your trust in our technology!

For reasons of safety and approval (CE) the personal reconstruction and/or modification of this product is prohibited. Please

observe that damage caused by modifications performed manually to this device is not covered by the warranty.

This product leaves our works in a perfect condition. Please observe all notes in these operating instructions to warrant this

condition and the safe operation of the product!

Any damage caused as a result of the non-compliance with these operating instructions leads to the expiration of any warranty

claim. The manufacturer does not accept liability for any damage to property or for personal injury resulting from the improper

handling of the product, or non-observance of the operating instructions.

Store these operating instructions in a safe place for later reference and pass them to any new holder when selling or lending or

leaving this device in the hands of any other party.

1. Instruction

1.1. Application According to Purpose

This product is a lighting effect which creates special light effects with one lamp. To generate these effects, the product must be

connected to mains and a DMX-512 compatible controller.

This product is designed for 230V, 50Hz A/C operation and exclusively for indoor use.

If used for any purpose other than described in these operating instructions, the device may suffer damage and the warranty

expires. Also, any other use is linked with risks such as short circuits, fire, electrical shock, etc.

The manufacturer's serial number must never be removed as otherwise the warranty expires.

1.2. Safety and Maintenance

 Indoor use only

 Make sure the equipment load-bearing structures can withstand the weight of more than 10 times when above ground

installation

 Disconnect with power supply before replacing lamp, fuse or other accessories

 Only operation under electrical standards with leakage protection device A/C

 Cool down for 15 mins before replacing lamps. Please do not use other company's accessories.

 Contact your specialized dealer for any technical problem

1.3. Safety operation

www.flash-butrym.pl

 Do not operate without outer cover or lenses

 Do not look directly to the light

 Replace immediately when lamp broken

 Do not project directly to items near 0.5M

 Do not operate when temperature up to 40°C

2. Lamp

ATTENTION:

DANGER OF LIFE! RISK OF BURNS!

RISK OF FIRE!

During operation, the lamps will reach temperatures of up to 600°C. Touching the lamps may cause serious burns! Objects coming

into contact with the lamps during and shortly after operation may catch fire!

2.1 Replacing the lamp

a. Disconnect the product from mains prior to installing or before changing a lamp! Allow a lamp to cool for approx. 15 minutes

before exchanging it!

b. After make sure projector cool down, take off the four screws in the head cover, then take off the fans from the projector.

c. Take the new lamp out of its package and insert in the fitting.

WARNING: Do not touch the lamp’s envelope with bare hands. Should this happen, clean the bulb with a cloth soaked in alcohol

and dry it with a clean, dry cloth.

Never touch a lamp with bare hands! If damaged or deformed, a lamp must be exchanged!

d. When exchanging the lamp be sure to use suitable lamps only. Lamps with greater performance generate excessive heat for the

product; risk of fire! Damage resulting from the use of an unsuitable lamp is exempt from warranty!

e. Never connect the lighting effect to the mains prior with opened housing.

f. After changing lamps, well connected the cables, fans, otherwise will damage the parts inside.

3. Supply Voltages, Mains Cord and Connection to Mains

ATTENTION:

DANGER OF LIFE!

RISK OF FIRE! RISK OF SHORT CIRCUIT!

The handling of supply voltage, mains cords and connections to mains calls for particular care considering the risk from a

life-threatening electric shock, the risk of fire and the risk of short circuits! Please observe the following notes in particular:

www.flash-butrym.pl