Thorn WeatherForce LED Installation Instructions Manual

IP65

IP65

IP65 IP65

IP65 IP65

WeatherForce LED

Installation Instructions

Warning

Please read these instructions carefully before installation or lamp
replacement. Warranty of this product is subject to installation
and maintenance being carried using appropriate conventional
practices and/or any specic instructions enclosed within.

Installation must be carried out by a qualied electrician in
accordance with local wiring regulations. Ensure that the rated
voltage and frequency of the luminaire are compatible with the
electrical supply.

Disconnect mains power supply before installing, servicing or
maintaining the luminaire.

Changes to specication

The right is reserved to change the design and/or specication
without prior notice or public announcement.

Specication

This luminaire is designed to comply with
the requirements of AS/NZS 60598.

Supply Voltage: 240v ~ 50Hz

Classication For Protection: Against electric shock:

Class 1 earthed metalwork. This luminaire must be earthed.

IP Rating: 65 - A 6-10mm Ø, circular electrical supply
cable must be used to maintain the IP rating.

Maximum ambient operating temperature:

Up to Ta: 25�C

1. Remove the diffuser and gear tray

Product application

IP65

To install, remove diffuser, detach gear tray and maintenance suspension devices.

Installation positions and IP rating

This strong impact resistant product is made from Polycarbonate.
This material is ideal in waterproof & industrial applications.
However, it is not suitable for use in areas prone to contact with
solvents, detergents, oil, alkalis, organic chemicals, animal fats &
industrial cleaners.

Please contact your local Thorn ofce for suitable alternative
products to suit the above applications

Remove Screws

Suspended Mounting Direct Mounting

600mm Single

416mm 507mm

600mm Twin

1200mm Single

880mm 980mm

1200mm Twin

Green/Yellow Earth

Brown Active

Blue Neutral

1

2

3

SAP No: 96540006 Rev: A 1/2013

thn_weatherforce_0113

Thorn Lighting Pty Limited (ABN 74 060 142 501)

Head Ofce: 43 Newton Road, Wetherill Park NSW 2164

Ph. 1300 139 965 Fax. [phone] www.thornlighting.com.au

Attach the gear tray to the
base. Tighten screws rmly.

Fit the uorescent lamp (ordered
separately).

Attach the diffuser to the base.
Ensure the diffuser is locked in
place.

Mounting kits suitable for surface mounting, or suspension mounting
are available to order.

Order reference: Single - 96039252, Twin - 96039253.

5. Secure the gear tray to the base

8. Attach the diffuser

Mounting kits

Make the electrical connections at the terminal block.

4. Make the electrical connections

The WeatherForce can be mounted by direct screw xing through the
housing. It should only be drilled at the appropriate marked points where
the housing is suitably reinforced. Do not use oil.

Note: Fixing screws and washers are NOT supplied.

It is recommended drill bits specically designed for plastic are used.
Standard metal or timber twist drills may be used but if not properly
prepared for plastic they can instigate stress cracking which may spread
under load.

Do not overtighten any screws into or in contact with the plastic housing.
Permanent damage may occur even if not immediately obvious.
Recommended maximum torque 1.5Nm

It is recommended that installation is made using the end entry and gland
kit provided with the tting.

Warning: If the housing is pierced for back entry of cabling, do not run
mains cabling past ballast, Temperatures exceed 100°C.

Fit the electrical supply cable, conduit and cable gland to the entry point
on the base. Ensure the cable gland is tightened rmly.

Note: If not suitably sealed with
appropriate washers, glands
or proprietary sealing kits any
piercing of the housing will
interfere with the IP rating of
the product.

2. Mount the luminaire

3. Attach conduit, cable glands and electrical
supply cable to tting.

Mounting point

Mounting screws

Cable gland

Suspension mounting kit

Surface mounting kit

Screw

Washer