THOMAS DÖRR TD 3000L M14 Operating Instructions Manual

Operating instructions

Cutlery polishing machine

TD 3000L M14

Kitchen and Cutlery Systems

Hettenbergring 47
D-74889 Sinsheim

Tel.: [phone] / 9754-93
Fax: [phone] / 9754-94

08/2017

English translation of the original operating instructions manual

Page 2 of 18

Table of Contents

1. GENERAL INFORMATION 3

1.1 INTRODUCTION 3

1.2 EXPLANATIONS 3

1.3 DELIVERY CONTENTS 3

2. SAFETY 4

2.1 PROPER USE 4

2.2 IMPROPER USE 4

2.3 GENERAL SAFETY INSTRUCTIONS 4

3. SHIPPING, STORAGE AND SET UP 5

3.1 SHIPPING 5

3.2 STORAGE 5

3.3 UNPACKING 5

3.4 SET UP 5

3.5 REMOVING THE TRANSPORTATION SAFETY DEVICE 6

4. HANDLING 7

4.1 BEFORE INITIAL OPERATION 7

4.2 EXPLANATION TO MACHINE OPERATION 7

4.3 START UP AND OPERATION OF THE CUTLERY POLISHING MACHINE 8

4.4 FURTHER SAFETY REFERANCES 8

5. CLEANING AND MAINTENENCE 9

5.1 DAILY CLEANING 9

5.2 REPLACING THE GRANULATE AND CLEANING THE MACHINE 9

5.3 REPLACING THE UVC LAMP 10

6. TROUBLESHOOTING 11

7. ACCESSORIES FOR THE CUTLERY POLISHING MACHINE 14

8. COMPANY ADDRESS 15

9. TECHNICAL DATA 15

10. DISPOSAL OF THE MACHINE 15

11. CE - DECLARATION OF CONFORMITY 16

12. NOTES 17

Page 3 of 18

1. General Information

1.1 Introduction

This instruction manual contains useful information on the use and service of the cutlery polisher and must be read
thoroughly before the machine is put into operation.

Requirements for operating and maintenance personnel
Anyone working on or with the machine, whether its initial start-up, installation, operation, or maintenance is required to
read and understand this operating instructions manual. Especially the chapter on “safety” which is listed ahead.

Only sufficiently trained personnel are elligeable to operate the machine.

► Always keep this manual within reach
► Observe all safety precautions and indications
► When passing on the machine to any other persons be sure to hand over this instruction manual with it

1.2 Explanations

1.2.1 Meaning of safety indications

Symbol

Signal term

Meaning

Result if ignored

WARNING!

Possible dangerous situation

Death or serious injury

CAUTION!

Injury

CAUTION!

Possible property damage

Slight or heavy damage to the

machine

No signal term

Useful tips and indications

none

1.3 Delivery Contents

1 x cutlery polishing machine
1 x operation instructions manual
1 x instruction sheet for easy machine operation (place near polishing machine)
1 x granulate replacement chart

Page 4 of 18

2. Safety

2.1 Proper use

The intended use of the machine is only drying and polishing chrome, steel, or silver cutlery. The following cutlery
pieces can be used:

► spoon ► fork
► knife ► small fork
► tea spoon

2.2 Improper use

The machine is not designed to polish any other sorts of cutlery or foreign utensils. Any other use is not according to
regulations and therefore prohibited. We take no responsibilities for damage caused by improper use.

2.3 General safety instructions

Warning!

Death or serious injury may accur by means of electrical shock

> Never install or operate the machine with a damaged power cord.
> By suspicion of damage, for example an electrical fault smell, disconnect the machine from the power circuit

immediately and contact the Dörr-service personnel.

> A damaged power cable can only be repaired by a Dörr-service member or a from Dörr authorized service

technician.

> Make sure the power cable is never placed near a hot surface.
> Make sure the power cable is never pinched or brushed along a sharp edge or surface.
> Never open and repair the machine yourself. Make no changes to the machine that are not listed in this manual.

This device contains electrical current-carrying parts. After opening, the risk of death or serious injury could
occur. Repairs can only be made by Dörr authorised service technicians with original Dörr spare parts and
accessories.

> Never expose the machine to gushes or jets of water.

Caution!

Risk of injury

> Any installed safety components are not to be changed or demounted.
> Never put your hands in the machine.
> To prevent cuts always insert cutlery by holding the handle of the cutlery.
> Never touch hot parts.
> Never let the power cord hang loose. It could be tripped over or damaged.
> Before performing any cleaning or maintenence work be sure that the power switch is turned off to “O” and the

power cord is disconnected.

> Turn the machine off when not using it for a longer period of time.
> This device must be installed to an appropriate connected power circuit.(See page 15)
> Exclusively use the original Dörr Polishing Granulate SG 3000L as well as original Dörr cleaning products.
> Install the device far from the reach of children.
> Persons, including children, who by reason of physical,sensual or mental complications or unexperience or

ignorance may not operate the machine without guidance from a responsible person.

> Persons who are not capable of reading or cannot read this manual`s language must be educated and trained

about the contents of this manual and operation of the machine.

Page 5 of 18

3. Shipping, storage and set up

3.1 Shipping

The following steps must be followed when the machine is being, or has been transported:

► Never tilt or turn over the machine
► Check the machine in advance for any damage caused by the shipment
► Use the transportation safety device when shipping the machine
► When reshipping, make sure the machine has a straight and sturdy stance
► Do not place any transport goods on top of the machine

There will be no replacements or warranty claims eligible by improper transportation methods.

3.2 Storage

Take note to the following information when storing the machine:

► Do not store the machine in a moist area
► Cover up, wrap up or keep the machine in its original packaging
► Assure a stable storing method
► Always keep in mind that the weight of the machine can be a factor when storing on shelves
► Do not place any items on top of the machine

3.3 Unpacking

► Never tilt or turn over the machine
► Save the packaging for future shipments or dispose it properly

3.4 Set up

It is recommended to set up the cutlery polisher in the dish washing area.

► Place the machine on a safe and sturdy leveled surface
► Leave approximately 20 mm of space between the wall since the machine causes light vibrations when running
► Operating and cleaning must be enabled from a safe stand point

Page 6 of 18

3.5 Removing the transportation safety device

Instructions for removing the transportation safety device:

CAUTION!

Never operate the machine before removing the transportation safety device. It could result in damaging
the machine!

 The transportation safety device must be removed before the first initial operation.

1. Open the top cover and remove the
Star grip by loosening it

2. Loosen and remove the wing nut by
turning it counter clockwise

3. Remove transportation safety device

4. Fasten the star grip and close the top
cover