Page 1
Danger of Electric Shock! Installation of this product must be performed
by trained installers in accordance with all applicable local, state and
national electrical codes, installation standards and safety rules.
INSTALLATION INSTRUCTIONS
for UH1000 Connector
WARNING
#2 to 2/0 CUT HERE *(.380-.580)
3/0 to 250 CUT HERE *(.580-.765)
300 to 500 CUT HERE *(.760-1.003)
500 to 750 CUT HERE *(.926-.1.218)
750 to 1000 CUT HERE *(1.128-1.372)
1000 CUT HERE *(1.280-1.662)
* DECIMAL RANGE
Remove insulating sleeve
1.
from the outlet. Select
2 2/0
3/0 250
300 500
500 750
750 1000
1000
3.
correct cut-off ring for cable
being used.
Cut off rocket sleeve at the
2.
tip of arrow, leaving correct
cable size showing on
opened rocket.
0
/
2
2
0
5
2
3
/
0
3
0
0
0
0
5
0
5
5
0
7
0
0
7
0
5
0
0
1
1
0
0
0
5.
Limited Warranty Applies. Refer to:
www.tnb.com/ecpwarranty for full warranty terms.
© 2012 Thomas & Betts. All Rights Reserved.
Strip the insulation from
the cable end baring
approx. 3” of conductor.
Pencilling is preferred
although not necessary.
Thoroughly wire
brush bare conductor
with compound to
break up oxides.
Insert conductor into the
4.
Apply silicone
grease. Slide cut
rocket over
6.
outlet barrel. Tighten set
screws down on the
conductor, starting with
the outermost screw.
prepared cable.
WIRE SIZE
#14 to #3
#2 to 350 MCM
400 MCM to 750 MCM
800 MCM to 1000 MCM
Slide rocket sleeve over
7.
outlet and onto PVC
shoulder until rocket butts
against connector bar.
Thomas & Betts Corporation
Memphis, Tennessee
www.tnb.com
INCH POUNDS
120
240
360
500
FOOT POUNDS
10
20
30
42
0507285 A
192_R1
Page 1 of 1
#2 to 2/0 CUT HERE *(.380-.580)
3/0 to 250 CUT HERE *(.580-.765)
300 to 500 CUT HERE *(.760-1.003)
500 to 750 CUT HERE *(.926-.1.218)
750 to 1000 CUT HERE *(1.128-1.372)
1000 CUT HERE *(1.280-1.662)
* DECIMAL RANGE
Remove insulating sleeve
1.
from the outlet. Select
correct cut-off ring for cable
being used.
Cut off rocket sleeve at the
2.
tip of arrow, leaving correct
cable size showing on
opened rocket.
INSTALLATION INSTRUCTIONS
for UH1000 Connectors
Strip the insulation from
2 2/0
3/0 250
300 500
500 750
750 1000
1000
3
5
7
1
0
0
0
/
2
2
0
5
2
3
/
0
0
0
0
0
5
0
5
0
7
0
0
0
5
0
0
1
0
3.
the cable end baring
approx. 3” of conductor.
Pencilling is preferred
although not necessary.
Thoroughly wire
5.
brush bare conductor
with compound to
break up oxides.
Danger of Electric Shock! Installation of this product must be performed
WARNING
by trained installers in accordance with all applicable local, state and
national electrical codes, installation standards and safety rules.
Insert conductor into the
4.
Apply silicone
grease. Slide cut
rocket over
prepared cable.
6.
outlet barrel. Tighten set
screws down on the
conductor, starting with
the outermost screw.
WIRE SIZE
#14 to #3
#2 to 350 MCM
400 MCM to 750 MCM
800 MCM to 1000 MCM
Slide rocket sleeve over
7.
outlet and onto PVC
shoulder until rocket butts
against connector bar.
INCH POUNDS
120
240
360
500
FOOT POUNDS
10
20
30
42
Limited Warranty Applies. Refer to:
www.tnb.com/ecpwarranty for full warranty terms.
© 2012 Thomas & Betts. All Rights Reserved.
Thomas & Betts Corporation
Memphis, Tennessee
www.tnb.com
0507285 A
192_R1
Page 1 of 1
Loading...