Page 1
®
(KPR) KITCHEN POWER POP-UP RECEPTACLE
Also suitable for use in bathrooms or other permanent (or xed) indoor work surface.
Installation Instructions
For Catalog Numbers
KPR-15G-BRZ (Bronze), KPR-15G-BRS (Brass) and KPR-15G-NKL (Brushed Nickel)
Voltage: 110-125 VAC – 60hz Current: 15 amp max.
IMPORTANT: Read all instructions before installing KPR Kitchen Power Pop-Up.
WARNING
RISK OF SHOCK, DISCONNECT
POWER BEFORE INSTALLATION.
WARNING
•
For indoor use only.
• If any malfunction occurs, do not attempt to repair.
• This product has no field serviceable parts.
• Use this product only for its intended uses as described.
• Do not install in line with power converter.
• Do not use attachments not recommended by
manufacturer.
• Do not insert foreign objects into power outlet receptacles.
• For counter top mounting only.
Cut-out and Mounting Procedure
1. Select desired counter top surface. Surface must be between
3/8” and 1-7/8” thick and have underneath clearance of at
least 17-5/8” (see Figure 1).
Counter Top Surface
3/8” to 1-7/8”
17-5/8”
Inside Bottom Surface
FIGURE 1
2. On the desired counter top surface, cut a hole 3-3/4” in
diameter. Allow at least 1-7/8” between the side of the hole and
the edge of the at counter top surface (see Figure 2). Locate
the hole at least 10” away from stove top or any other heated
surfaces.
IMPORTANT: To avoid damage to the surface, only a qualied
professional should cut the hole in a non-wood surface such
as marble or granite. To ensure that the water seal will operate
correctly, the unit should only be mounted on a smooth counter
top surface, free from joints, seams or rough textures.
3. Before lowering unit into the prepared hole, remove rubber
washer and locking ring by turning counterclockwise (see
Figure 3). Retain rubber washer and locking ring for step 5..
4.
Lower KPR unit into the hole until the mounting collar lip is ush with
the counter top surface all the way around – this will ensure a good
watertight seal (see Figure 4). Orient the receptacle as desired.
CAUTION
KPR should be installed by a qualied electrician
in accordance with national and local electrical
codes.
1-7/8” min. between side
of mounting hole and
edge of work surface.
Ø 3-3/4”
FIGURE 2
Lid
Top cap
& water
seal
Collar
Lip
Remove
Locking Ring
by rotating
Counterclockwise.
FIGURE 3 FIGURE 4
Continued on back page.
Counter Top Surface
Lower
KPR
into
hole
Collar
Ensure collar
lip is ush with
counter top
surface.
Locking
Ring
Set
Screws
TA04600 B Page 1 of 2
Page 2
5. With the rubberized compression lip upwards, place locking
ring onto collar. Identify & align arrows on collar and locking ring
to ensure the thread is engaged properly. Turn the locking ring
clockwise (viewed from below) to tighten. Make sure locking
ring with rubber washer is compressed tightly on underside of
mounting surface (see Figure 5). Tighten set screws.
6. Connect HOT (black), Neutral (white) and Ground (green)
conductors in a junction box according to national electrical
code and all local codes (see Figure 6).
Mounting
Surface
To tighten, turn
Locking Ring
clockwise.
FIGURE 6
Power
Line In
From
KPR
Cover Plate
Whip Provided
Tighten Set
Screws
Ensure Locking Ring and Rubber
Washer is compressed tightly to
FIGURE 5
WARRANTY: Thomas & Betts sells this product with the understanding that the user will perform all necessary tests to determine the suitability of this product for
the user’s intended application. Thomas & Betts warrants that this product will be free from defects in materials and workmanship for a period of ninety (90) days
following the date of purchase. Upon prompt notification of any warranted defect, Thomas & Betts will, at its option, repair or replace the defective product or refund
the purchase price. Proof of purchase is required. Misuse or unauthorized modification of the product voids all warranties.
Limitations and Exclusions: THE ABOVE WARRANTY IS THE SOLE WARRANTY CONCERNING THIS PRODUCT, AND IS IN LIEU OF ALL OTHER WARRANTIES
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
WHICH ARE SPECIFICALLY DISCLAIMED. LIABILITY FOR BREACH OF THE ABOVE WARRANTY IS LIMITED TO COST OF REPAIR OR REPLACEMENT OF
THE PRODUCT, AND UNDER NO CIRCUMSTANCES WILL THOMAS & BETTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
work surface.
TA04600 B Page 2 of 2
Thomas & Betts Corporation
Memphis, Tennessee
www.tnb.com
© 2012 Thomas & Betts. All Rights Reserved.
Loading...