Thomas & Betts FPT4 SERIES MOPTITE Installation Instructions
Installation Instructions for
FPT4 SERIES MOPTITE® Poke Through Cover
FPT4-CVR-TBRS FPT-CVR-TALM FPT4-CVR-TBLK
FPT4-CVR-TBGE FPT4-CVR-TBRN
WARNING
ELECTRIC SHOCK HAZARD.
DISCONNECT THE ELECTRICAL SUPPLY
POWER TO THE OUTLET PRIOR TO
INSTALLATION.
CONSULT A QUALIFIED ELECTRICIAN IF
YOU HAVE ANY QUESTIONS.
#6-32 x 1/4” Long
Flat Head Screws
(4-Places)
Cover
NOTE:
This cover is used with A FTP4 Series Poke
Through. THIS COVER CAN BE OPENED WITHOUT
TOOLS.
Installation Instructions
1. Remove temporary cover from poke through by
unscrewing the (4) #6-32 x 3/4” long screws, exposing
the poke through mounting ring (see Figure 1).
2. PREPARE FLOOR FOR COVER INSTALLATION
(CARPET, WOOD, TILE and LINOLEUM): Remove or
install oor material leaving a 7” diameter opening
around center of poke through. Use template provided
with this instruction.
CONCRETE: No preparation required.
3. Align Holes in trim plate with holes in poke through
mounting ring and attach mounting plate using (4)
#6-32 x 1/4” long at head screws furnished (see Figure 1)
4. APPLY SEALANT TO FLOOR:
4a) CONCRETE AND CARPET: Apply complete bead of
sealant or caulk directly to concrete around trim plate
to within 1/4” from outside edge of plate. On carpet,
keep sealant within 7” diameter cut-out. Use enough
sealant to block water entry.
4b) TITLE, WOOD AND LINOLEUM: Apply moderate
amount of sealant directly on nished oor next to
cut-out edge. Fully surround 7” diameter opening in
oor. Use enough sealant to block water entry.
5. Install cover to trim plate using (4) #6-32 x 1/4” at head
screws furnished (see Figure 1).
6. Close lid and push down on top of cover to fully seat
poke through cover to oor. Step on cover with foot to
push poke through rmly against oor. Clean excess
sealant around cover edge (see Figure 2).
.
Remove
Temporary
Cover
Mounting
Ring
Tile, Wood and
Linoleum Floors
(See Sealant Note 4b)
Figure 1
Pull Release
back to open
Cover
Figure 2
Trim Plate
Concrete and
Carpet (See
Sealant Note 4a)
7” Diameter
Cut-out in
Flooring
See Step 2
See Step 6
WARRANTY: Thomas & Betts sells this product with the understanding that the user will perform all necessary tests to determine the suitability of this product for the user’s intended application. Thomas & Betts warrants
that this product will be free from defects in materials and workmanship for a period of two (2) years following the date of purchse. Upon prompt notication of any warranted defect, Thomas & Betts will, at its option, repair or
replace the defective product or refund the purchase price. Proof of purchase is required. Misuse or unauthorized modication of the product voids all warranties.
Limitations and Exclusions:
TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE SPECIFICALLY DISCLAIMED. LIABILITY FOR BREACH OF THE ABOVE WARRANTY IS LIMITED TO
COST OF REPAIR OR REPLACEMENT OF THE PRODUCT, AND UNDER NO CIRCUMSTANCES WILL THOMAS & BETTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
© 2010 Thomas & Betts. All Rights Reserved. TA04578 A Page 1 of 2
THE ABOVE WARRANTY IS THE SOLE WARRANTY CONCERNING THIS PRODUCT, AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
Thomas & Betts Corporation
Memphis, Tennessee
TEMPLATE FOR FLOOR CUT OUT
In Carpet, Wood,
Tile and Linoleum Floor
7” Hole
Ø Core Hole
4-1/16”
CAUTION:
COPIES, BE SURE THE TEMPLATE
IS SCALED CORRECTLY.
WHEN PRINTING
TA04578 A Page 2 of 2
Loading...