Select the correct cut-off ring for the
1
cable being used.
14 10
8 4
2 1/0
2/0 250
300 400
#14 to #10 (SL)
#8 to #4 *(.24-.38)
#2 to 1/0 *(.38-.54)
2/0-250 *(.53-.78)
300-400 (.74-.98)
* Decimal range
Danger of Electric Shock! Installation of this product must be performed
by trained installers in accordance with all applicable local, state and
national electrical codes, installation standards and safety rules.
INSTALLATION INSTRUCTIONS
for "Flood-Seal"® Copper In-Line Mechanical Splice Kits
CBS 12-2 K CBS 4-20 K CBS 2-40 K
Cut off the rocket sleeve at the tip of the
2
arrow, leaving the
correct cable size
showing on the
opened rocket.
Wipe the cable clean. Bevel the end of the
3
1
4
0
1
8
4
2
0
1
/
2
/
0
0
2
5
3
0
0
0
0
4
cable
insulation for
ease of
installation.
Apply silicone grease to the end of the
4
cable and the cut opening of the rocket.
Slide the rocket over the cable. Repeat
steps 2, 3 and
4 on the other
cable end.
Strip the cable insulation and
5
install the connector, using
the chart below as a guide.
Catalog Number
CBS 12-2 K
CBS 4-20 K
CBS 2-40 K
Apply silicone grease to the open edges of
6
the rockets. Center the connector between
the covers. Slide the covers together.
WARNING
Strip Length Hex Wrench
1 -1/2”
1 -1/2”
1 -3/4”
5/32
5/32
3/16
Limited Warranty Applies. Refer to:
www.tnb.com/ecpwarranty for full warranty terms.
© 2012 Thomas & Betts. All Rights Reserved.
INSTALLATION INSTRUCTIONS
for "Flood-Seal"® Copper In-Line Mechanical Splice Kits
CBS 12-2 K CBS 4-20 K CBS 2-40 K
Select the correct cut-off ring for the
1
cable being used.
14 10
8 4
2 1/0
2/0 250
300 400
#14 to #10 (SL)
#8 to #4 *(.24-.38)
#2 to 1/0 *(.38-.54)
2/0-250 *(.53-.78)
300-400 (.74-.98)
Cut off the rocket sleeve at the tip of the
2
arrow, leaving the
correct cable size
showing on the
opened rocket.
Wipe the cable clean. Bevel the end of the
3
cable
insulation for
ease of
installation.
Thomas & Betts Corporation
Memphis, Tennessee
www.tnb.com
Danger of Electric Shock! Installation of this product must be performed
by trained installers in accordance with all applicable local, state and
national electrical codes, installation standards and safety rules.
5
1
4
0
1
8
4
2
0
1
/
2
/
0
0
2
5
3
0
0
0
0
4
Catalog Number
6
0015156 A
154_R2
Page 1 of 1
WARNING
Strip the cable insulation and
install the connector, using
the chart below as a guide.
CBS 12-2 K
CBS 4-20 K
CBS 2-40 K
Apply silicone grease to the open edges of
the rockets. Center the connector between
the covers. Slide the covers together.
Strip Length Hex Wrench
1 -1/2”
1 -1/2”
1 -3/4”
5/32
5/32
3/16
Apply silicone grease to the end of the
4
cable and the cut opening of the rocket.
Slide the rocket over the cable. Repeat
steps 2, 3 and
* Decimal range
4 on the other
cable end.
Limited Warranty Applies. Refer to:
www.tnb.com/ecpwarranty for full warranty terms.
© 2012 Thomas & Betts. All Rights Reserved.
Thomas & Betts Corporation
Memphis, Tennessee
www.tnb.com
0015156 A
154_R2
Page 1 of 1
Loading...