thomann Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX, Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX User Manual

Wild Wash 132 LED RGB DMX,

Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX,

Wild Wash 648 LED White DMX

LED floodlight

user manual

Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: [phone]
E-mail: [e-mail]
Internet: www.thomann.de

27.10.2016, ID: 399664, 399663, 399658, 399662

Table of contents

1 General notes............................................................................................................................................... 5

1.1 Further information........................................................................................................................... 6

1.2 Notational conventions.................................................................................................................... 7

1.3 Symbols and signal words............................................................................................................... 8

2 Safety instructions.................................................................................................................................. 10

3 Features....................................................................................................................................................... 15

4 Installation.................................................................................................................................................. 16

5 Starting up.................................................................................................................................................. 19

6 Connections and controls................................................................................................................... 22

7 Operating.................................................................................................................................................... 27

7.1 Starting the device........................................................................................................................... 27

7.2 Main menu.......................................................................................................................................... 28

7.3 Menu overview................................................................................................................................. 38

7.4 Functions in DMX mode 1ch........................................................................................................ 41

7.5 Functions in DMX mode 2Ch (model versions with white LEDs)................................... 41

Table of contents

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

3

7.6 Functions in DMX mode 2Ch1 (model versions with RGB LEDs).................................... 42

7.7 Functions in DMX mode 2Ch2 (model versions with white LEDs)................................. 44

7.8 Functions in DMX mode 3Ch1 .................................................................................................... 45

7.9 Functions in DMX mode 3Ch2 (model versions with RGB LEDs).................................... 46

7.10 Functions in DMX mode 3Ch2 (model versions with white LEDs)............................... 48

7.11 Functions in DMX mode 3Ch3 (model versions with RGB LEDs).................................. 50

7.12 Functions in DMX mode 4Ch (model versions with RGB LEDs).................................... 50

7.13 Functions in DMX mode 5Ch (model versions with white LEDs)................................. 53

7.14 Functions in DMX mode 6Ch (model versions with RGB LEDs).................................... 55

7.15 Functions in DMX mode 7Ch (model version with 648 white LEDs).......................... 57

8 Technical specifications....................................................................................................................... 59

9 Plug and connection assignments.................................................................................................. 63

10 Troubleshooting...................................................................................................................................... 64

11 Cleaning....................................................................................................................................................... 66

12 Protecting the environment.............................................................................................................. 67

Table of contents

LED floodlight

4

1 General notes

This manual contains important instructions for the safe operation of the unit. Read and follow
the safety instructions and all other instructions. Keep the manual for future reference. Make
sure that it is available to all those using the device. If you sell the unit please make sure that
the buyer also receives this manual.

Our products are subject to a process of continuous development. Thus, they are subject to
change.

General notes

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

5

1.1 Further information

On our website (www.thomann.de) you will find lots of further information and details on the
following points:

Download This manual is also available as PDF file for you to download.

Keyword search

Use the search function in the electronic version to find the topics of
interest for you quickly.

Online guides

Our online guides provide detailed information on technical basics
and terms.

Personal consultation For personal consultation please contact our technical hotline.

Service

If you have any problems with the device the customer service will
gladly assist you.

General notes

LED floodlight

6

1.2 Notational conventions

This manual uses the following notational conventions:

The letterings for connectors and controls are marked by square brackets and italics.
Examples: [VOLUME] control, [Mono] button.

Texts and values displayed on the device are marked by quotation marks and italics.
Examples: ‘24ch’ , ‘OFF’.

References to other locations in this manual are identified by an arrow and the specified page
number. In the electronic version of the manual, you can click the cross-reference to jump to
the specified location.

Example: See

Ä

‘Cross-references’ on page 7.

Letterings

Displays

Cross-references

General notes

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

7

1.3 Symbols and signal words

In this section you will find an overview of the meaning of symbols and signal words that are
used in this manual.

Signal word Meaning
DANGER! This combination of symbol and signal word indicates an

immediate dangerous situation that will result in death or
serious injury if it is not avoided.

WARNING! This combination of symbol and signal word indicates a pos‐

sible dangerous situation that can result in death or serious
injury if it is not avoided.

NOTICE! This combination of symbol and signal word indicates a pos‐

sible dangerous situation that can result in material and
environmental damage if it is not avoided.

General notes

LED floodlight

8

Warning signs Type of danger

Warning – high-voltage.

Warning – suspended load.

Warning – danger zone.

General notes

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

9

2 Safety instructions

This device is intended to be used as an electronic illumination effect using LED technics. The
device is designed for professional use and is not suitable for use in households. Use the
device only as described in this user manual. Any other use or use under other operating con‐
ditions is considered to be improper and may result in personal injury or property damage. No
liability will be assumed for damages resulting from improper use.

This device may be used only by persons with sufficient physical, sensorial, and intellectual
abilities and having corresponding knowledge and experience. Other persons may use this
device only if they are supervised or instructed by a person who is responsible for their safety.

Intended use

Safety instructions

LED floodlight

10

DANGER!
Danger for children

Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard!

Ensure that children do not detach any small parts (e.g. knobs or the like) from
the unit. They could swallow the pieces and choke!

Never let children unattended use electrical devices.

DANGER!
Electric shock caused by high voltages inside

Within the device there are areas where high voltages may be present. Never
remove any covers.

There are no user-serviceable parts inside.
Do not use the device if covers, protectors or optical components are missing or

damaged.

Safety

Safety instructions

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

11

DANGER!
Electric shock caused by short-circuit

Always use proper ready-made insulated mains cabling (power cord) with a pro‐
tective contact plug. Do not modify the mains cable or the plug. Failure to do so
could result in electric shock/death or fire. If in doubt, seek advice from a regis‐
tered electrician.

WARNING!
Eye damage caused by high light intensity

Never look directly into the light source.

WARNING!
Risk of epileptic shock

Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons
should avoid looking at strobe lights.

Safety instructions

LED floodlight

12

NOTICE!
Risk of fire

Do not block areas of ventilation. Do not install the device near any direct heat
source. Keep the device away from naked flames.

NOTICE!
Operating conditions

This device has been designed for indoor use only. To prevent damage, never
expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and
strong vibrations.

Safety instructions

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

13

NOTICE!
Power supply

Before connecting the device, ensure that the input voltage (AC outlet) matches
the voltage rating of the device and that the AC outlet is protected by a residual
current circuit breaker. Failure to do so could result in damage to the device and
possibly injure the user.

Unplug the device before electrical storms occur and when it is unused for long
periods of time to reduce the risk of electric shock or fire.

NOTICE!
Possible staining

The plasticiser contained in the rubber feet of this product may possibly react
with the coating of your parquet, linoleum, laminate or PVC floor and after some
time cause permanent dark stains.

In case of doubt, do not put the rubber feet directly on the floor, but use felt-pad
floor protectors or a carpet.

Safety instructions

LED floodlight

14

3 Features

The LED floodlight is particularly suitable for lighting applications in clubs and discotheques,
on rock stages, in theatres and musicals. It can also be used for effect lighting of stage back‐
grounds and as blinder.

Special features of the device:

n Equipped with SMD LEDs with 0.2 W power consumption each, depending on the model

version:
– Stairville Wild Wash 132 LED RGB DMX (item no. 399664): 132 tricolour LEDs (RGB)
– Stairville Wild Wash 132 LED White DMX (item no. 399663): 132 cold white LEDs
– Stairville Wild Wash 648 LED RGB DMX (item no. 399658): 648 tricolour LEDs (RGB)
– Stairville Wild Wash 648 LED White DMX (item no. 399662): 648 cold white LEDs

n Control via DMX (different modes depending on the model version) and via buttons and

display on the unit

n Built-in automatic show programmes
n Sound control
n Master / Slave mode
n Robust metal housing with compact design
n Versatile installation and mounting options with the included two-piece mounting bracket

Features

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

15

4 Installation

Unpack and carefully check that there is no transportation damage before using the unit. Keep
the equipment packaging. To fully protect the device against vibration, dust and moisture
during transportation or storage use the original packaging or your own packaging material
suitable for transport or storage, respectively.

You can install the device standing or hanging. When in use, the device must be mounted at a
solid surface or clamped to an approved truss.

Work from a stable platform whenever you install or move the device or when you perform
any kind of maintenance. Block access under the work area.

WARNING!
Risk of injury caused by falling objects

Make sure that the installation complies with the standards and rules that apply
in your country. Always secure the device with a secondary safety attachment,
such as a safety cable or a safety chain.

Installation

LED floodlight

16

NOTICE!
Risk of overheating

Always ensure sufficient ventilation.
The ambient temperature must always be below 40 °C (104 °F).

NOTICE!
Possible data transmission errors

For error-free operation make use of dedicated DMX cables and do not use ordi‐
nary microphone cables.

Never connect the DMX input or output to audio devices such as mixers or ampli‐
fiers.

Installation

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

17

Please note that this device must not be connected to a dimmer.

Installation

LED floodlight

18

5 Starting up

Create all connections while the device is off. Use the shortest possible high-quality cables for
all connections. Take care when running the cables to prevent tripping hazards.

Starting up

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

19

Connect the DMX input of the device to the DMX output of a DMX controller or another DMX
device. Connect the output of the first DMX device to the input of the second one, and so on
to form a daisy chain. Always ensure that the output of the last DMX device in the daisy chain
is terminated with a resistor (110 Ω, ¼ W).

Connections in DMX mode

Starting up

LED floodlight

20

If the unit is in DMX mode and a DMX controller is connected and turned on, the [DMX] LED
lights.

When you configure a group of devices in master/slave mode, the first unit will control the
other units for an automatic, sound-activated, synchronized show. This function is ideal when
you want to start a show immediately. Connect the DMX output of the master device to the
DMX input of the first slave device. Then connect the DMX output of the first slave device to
the DMX input of the second slave device and so on.

DMX indicator

Connections in master/slave
mode

Starting up

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

21

6 Connections and controls

Stairville Wild Wash 132 LED
RGB DMX (item no. 399664)

Connections and controls

LED floodlight

22

Stairville Wild Wash 132 LED
White DMX (item no. 399663)

Connections and controls

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

23

Stairville Wild Wash 648 LED
RGB DMX (item no. 399658)

Connections and controls

LED floodlight

24

Stairville Wild Wash 648 LED
White DMX (item no. 399662)

Connections and controls

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

25

1 Display and control buttons:

[MENU]: Activates the main menu and toggles between menu items.
[UP]: Increases the displayed value by one.
[DOWN]: Decreases the displayed value by one.
[ENTER]: Selects an option of the respective operating mode.

2 [DMX IN]: DMX input socket.

[DMX OUT]: DMX output socket.

3 [MIC]

Microphone for sound control.

4 IEC chassis connector for the power cable with fuse holder. Below, the range of the allowable input voltage is speci‐

fied.
5 Safety eyelet.
6 Two-piece bracket for hanging or installation and for securing the safety-rope.
7 Locking screw for fixing the spotlight.

Connections and controls

LED floodlight

26

7 Operating

7.1 Starting the device

Connect the device to the power supply to start operation. After a few seconds, the display
indicates that a reset is in progress. The device is then ready for use. The display shows the
operating mode that was selected when the unit was last powered off.

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

27

7.2 Main menu

This setting is only relevant if the device is controlled via a DMX controller.
Press [MODE] repeatedly until one of the available DMX modes appears in the display and

press [ENTER]. Use [UP] and [DOWN] to select the desired DMX mode and press [ENTER].
The following table shows the DMX modes available depending on the version.

Model version Available DMX modes

Stairville Wild Wash 132 LED
RGB DMX (item no. 399664)

1Ch, 2Ch1, 3Ch1, 3Ch2 (RGB), 3Ch3, 4Ch, 6Ch

Stairville Wild Wash 132 LED
White DMX (item no. 399663)

1Ch, 2Ch, 2Ch2, 3Ch1, 3Ch2 (W), 5Ch

Stairville Wild Wash 648 LED
RGB DMX (item no. 399664)

1Ch, 2Ch1, 3Ch1, 3Ch2 (RGB), 3Ch3, 4Ch, 6Ch

Stairville Wild Wash 648 LED
White DMX (item no. 399663)

1Ch, 2Ch, 2Ch2, 3Ch1, 3Ch2 (W), 5Ch, 7Ch

Operating mode ‘DMX’

Operating

LED floodlight

28

This setting is only relevant if the device is controlled via a DMX controller.
Press [MODE] repeatedly until the currently set DMX address appears in the display (‘Axxx’ )

and press [ENTER]. Use [UP] and [DOWN] to select the desired DMX address between 1 (‘A001’ )
and 512 (‘A512’ ) and press [ENTER].

This setting is only relevant if the device is not controlled via a DMX controller and not working
as slave in a master / slave configuration. In this mode, the brightness of the white LEDs can be
adjusted and a Strobe effect can be engaged.

Press [MODE] repeatedly until ‘C000’ appears in the display and press [ENTER]. Use [UP] and
[DOWN] to select the menu item ‘C1xx’ for brightness or the menu item ‘CFxx’ for the Strobe
effect and press [ENTER].

To adjust the brightness, use [UP] and [DOWN] to select a value between ‘C101’ (minimum
brightness) and ‘C199’ (maximum brightness) or ‘C100’ (blackout, LEDs off) and press [ENTER].

To adjust the Strobe effect, use [UP] and [DOWN] to select a value between ‘CF01’ (Strobe fre‐
quency approx. 1 Hz) and ‘CF99’ (Strobe frequency approx. 30 Hz) or ‘CF00’ (continuous light,
no Strobe effect) and press [ENTER].

DMX address

Operating mode ‘Manual con‐
trol’ (white LED model versions)

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

29

This setting is only relevant if the device is not controlled via a DMX controller and not working
as slave in a master / slave configuration. In this mode, the intensity of the LEDs can be
adjusted per colour and a Strobe effect can be engaged.

Press [MODE] repeatedly until ‘C1xx’ appears in the display and press [ENTER]. Use [UP] and
[DOWN] to select the menu item ‘C1xx’ , ‘C2xx’ or ‘C3xx’ for brightness of the red, green or
blue LEDs or the menu item ‘CFxx’ for the Strobe effect and press [ENTER].

To adjust the Strobe effect, use [UP] and [DOWN] to select a value between ‘CF01’ (flash fre‐
quency approx. 1 Hz) and ‘CF99’ (flash frequency approx. 30 Hz) or ‘CF00’ (continuous light, no
Strobe effect) and press [ENTER].

Operating mode ‘Manual con‐
trol’ (RGB LED model versions)

Operating

LED floodlight

30

This setting is only relevant if the device is not controlled via a DMX controller and not working
as slave in a master / slave configuration. In this mode, one of the three primary colours or a
predefined mixed colour can be selected.

Press [MODE] repeatedly until ‘CMxx’ appears in the display and press [ENTER]. Use [UP] and
[DOWN] to select a value between ‘CM01’ and ‘CM015’ and press [ENTER]. The table below
shows the colour assignment.

Setting Colour

CM01 Red
CM02 Amber
CM03 Warm yellow
CM04 Yellow
CM05 Green
CM06 Cyan
CM07 Cyan
CM08 Blue

Operating mode ‘Colour
macros’ (RGB LED model ver‐
sions)

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

31

Setting Colour

CM09 Lavender
CM10 Mauve
CM11 Magenta
CM12 Pink
CM13 Warm white
CM14 White
CM15 Cold white

Operating

LED floodlight

32

This setting is only relevant if the device is not controlled via a DMX controller and not working
as slave in a master / slave configuration. In this mode, the colours are changed at freely select‐
able speed, a Strobe effect can be engaged.

Press [MODE] repeatedly until ‘JUxx’ appears in the display and press [ENTER]. Use [UP] and
[DOWN] to select the menu item ‘JUxx’ for colour change speed or the menu item ‘JFxx’ for
the Strobe effect.

For colour change speed, use [UP] and [DOWN] to select a value between ‘JU00’ (minimum
speed) and ‘JU99’ (maximum speed) and press [ENTER].

To adjust the Strobe effect, use [UP] and [DOWN] to select a value between ‘JF01’ (flash fre‐
quency approx. 1 Hz) and ‘CF99’ (flash frequency approx. 30 Hz) or ‘CF00’ (continuous light, no
Strobe effect) and press [ENTER].

Operating mode ‘Automatic
colour change’ (RGB LED model
versions)

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

33

This setting is only relevant if the device is not controlled via a DMX controller and not working
as slave in a master / slave configuration. In this mode, the LEDs will gradually fade in with a
freely selectable speed from blackout to maximum brightness and reverse, a Strobe effect can
be engaged.

Press [MODE] repeatedly until ‘FA00’ appears in the display and press [ENTER]. Use [UP] and
[DOWN] to select the menu item ‘FAxx’ for the fading speed or the menu item ‘FFxx’ for the
Strobe effect and press [ENTER].

To adjust the fading speed, use [UP] and [DOWN] to select a value between ‘FA01’ (minimum
speed) and ‘FA99’ (maximum speed) and press [ENTER].

To adjust the Strobe effect, use [UP] and [DOWN] to select a value between ‘FF01’ (flash fre‐
quency approx. 1 Hz) and ‘FF99’ (flash frequency approx. 30 Hz) or ‘FF00’ (continuous light, no
Strobe effect) and press [ENTER].

Operating mode ‘Fading’ (white
LED model versions)

Operating

LED floodlight

34

This setting is only relevant if the device is not controlled via a DMX controller and not working
as slave in a master / slave configuration. In this mode, the LEDs gradually change between the
available colours at freely selectable speed, a Strobe effect can be engaged.

Press [MODE] repeatedly until ‘FA00’ appears in the display and press [ENTER]. Use [UP] and
[DOWN] to select the menu item ‘FAxx’ for the fading speed or the menu item ‘FAxx’ for the
Strobe effect and press [ENTER].

To adjust the fading speed, use [UP] and [DOWN] to select a value between ‘FA01’ (minimum
speed) and ‘FA99’ (maximum speed) or ‘C100’ and press [ENTER].

To adjust the Strobe effect, use [UP] and [DOWN] to select a value between ‘FF01’ (flash fre‐
quency approx. 1 Hz) and ‘FF99’ (flash frequency approx. 30 Hz) or ‘FF00’ (continuous light, no
Strobe effect) and press [ENTER].

This setting is only relevant if the device is not controlled via a DMX controller and not working
as slave in a master / slave configuration. In this mode, the LEDs will gradually fade in with a
freely selectable speed from blackout to maximum brightness and reverse, the Strobe effect is
automatically engaged in regular intervals.

Press [MODE] repeatedly until ‘AUTO’ appears in the display and press [ENTER]. For effect
speed, use [UP] and [DOWN] to select a value between ‘AU01’ (minimum speed) and ‘AU99’
(maximum speed) and press [ENTER].

Operating mode ‘Fading’ (RGB
LED model versions)

Operating mode ‘Automatic
show’ (white LED model ver‐
sions)

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

35

This setting is only relevant if the device is not controlled via a DMX controller and not working
as slave in a master / slave configuration. In this mode, the LEDs gradually change at freely
selectable speed between the available colours, the Strobe effect is automatically engaged in
regular intervals.

Press [MODE] repeatedly until ‘AUTO’ appears in the display and press [ENTER]. For effect
speed, use [UP] and [DOWN] to select a value between ‘AU01’ (minimum speed) and ‘AU99’
(maximum speed) and press [ENTER].

This setting is only relevant if the device is not controlled via a DMX controller and not working
as slave in a master / slave configuration. In this mode, the LEDs are controlled via the built-in
microphone.

Press [MODE] repeatedly until ‘SOUN’ appears in the display and press [ENTER]. For micro‐
phone sensitivity, use [UP] and [DOWN] to select a value between ‘SO00’ (minimum sensitivity)
and ‘SO99’ (maximum sensitivity) and press [ENTER].

Operating mode ‘Automatic
show’ (RGB LED model versions)

Operating mode ‘Sound control’

Operating

LED floodlight

36

This setting is only relevant if the device is not controlled via a DMX controller and working as
slave in a master / slave configuration. Master and slave devices are connected to each other
via a DMX cable, the master device is in one of the operating modes ‘Manual control’, ‘Fading’,
‘Automatic show’ or ‘Sound control’.

Press [MODE] repeatedly until ‘SLAV’ appears in the display and press [ENTER]. The slave device
now copies exactly the actions of the master device.

Operating mode ‘Slave’

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

37

7.3 Menu overview

Model version with 132 white
LEDs.

Operating

LED floodlight

38

Model version with 648 white
LEDs.

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

39

Model versions with RGB LEDs

Operating

LED floodlight

40

7.4 Functions in DMX mode 1ch

Channel Value Function

1 Strobe

0 … 10 LEDs off (blackout)
11 … 255 Strobe effect, speed increasing from approx. 0 Hz to 30 Hz

7.5 Functions in DMX mode 2Ch (model versions with white LEDs)

Channel Value Function

1 0 … 255 Dimmer (0 % to 100 %)
2 Strobe

0 … 5 LEDs on
6 … 10 LEDs off (blackout)

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

41

Channel Value Function

11 … 250 Strobe effect, speed increasing from approx. 0 Hz to 30 Hz
251 … 255 LEDs on

7.6 Functions in DMX mode 2Ch1 (model versions with RGB LEDs)

Channel Value Function

1 0 … 255 Dimmer (0 % to 100 %)
2 Colour macro

0 … 5 LEDs off (blackout)
6 … 13 Red
14 … 21 Amber
22 … 29 Warm yellow

Operating

LED floodlight

42

Channel Value Function

30 … 37 Yellow
38 … 45 Green
46 … 53 Cyan
54 … 61 Cyan
62 … 69 Blue
70 … 77 Lavender
78 … 85 Mauve
86 … 93 Magenta
94 … 101 Pink
102 … 109 Warm white
110 … 117 White
118 … 125 Cold white
126 … 128 Ending colour change

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

43

Channel Value Function

129 … 192 Colour change, increasing speed
193 … 255 Gradual colour change, increasing speed

7.7 Functions in DMX mode 2Ch2 (model versions with white LEDs)

Channel Value Function

1 0 … 255 Dimmer (0 % to 100 %)
2 Strobe

0 … 5 LEDs on
6 … 10 LEDs off (blackout)
11 … 250 Strobe effect, speed increasing from approx. 0 Hz to 30 Hz
251 … 255 LEDs on

Operating

LED floodlight

44

7.8 Functions in DMX mode 3Ch1

Channel Value Function

1 0 … 255 Dimmer (0 % to 100 %)
2 Strobe

0 … 5 LEDs on
6 … 10 LEDs off (blackout)
11 … 250 Strobe effect, speed increasing from approx. 0 Hz to 30 Hz
251 … 255 LEDs on

3 Flash impulse

0 … 255 Flash impulse duration, increasing from 0 ms to 510 ms

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

45

7.9 Functions in DMX mode 3Ch2 (model versions with RGB LEDs)

Channel Value Function

1 0 … 255 Dimmer (0 % to 100 %)
2 Strobe

0 … 5 LEDs on
6 … 10 LEDs off (blackout)
11 … 250 Strobe effect, speed increasing from approx. 0 Hz to 30 Hz
251 … 255 LEDs on

3 Colour macro

0 … 5 LEDs off (blackout)
6 … 13 Red
14 … 21 Amber
22 … 29 Warm yellow

Operating

LED floodlight

46

Channel Value Function

30 … 37 Yellow
38 … 45 Green
46 … 53 Cyan
54 … 61 Cyan
62 … 69 Blue
70 … 77 Lavender
78 … 85 Mauve
86 … 93 Magenta
94 … 101 Pink
102 … 109 Warm white
110 … 117 White
118 … 125 Cold white
126 … 128 Ending colour change

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

47

Channel Value Function

129 … 192 Colour change, increasing speed
193 … 255 Gradual colour change, increasing speed

7.10 Functions in DMX mode 3Ch2 (model versions with white LEDs)

Channel Value Function

1 0 … 255 Dimmer (0 % to 100 %)
2 Strobe

0 … 5 LEDs on, brightness controlled by channel 1
6 … 10 LEDs off (blackout)
11 … 33 Random impulses, increasing speed
34 … 56 Randomly increasing brightness, increasing speed

Operating

LED floodlight

48

Channel Value Function

57 … 79 Randomly decreasing brightness, increasing speed
80 … 102 Random Strobe effect, increasing speed
103 … 127 Interrupt effect, 5 s to 1 s
128 … 250 Strobe effect, speed increasing from approx. 0 Hz to 30 Hz
251 … 255 LEDs on, brightness controlled by channel 1

3 Sound control

0 … 5 Sound control off
6 … 255 Sound control on, increasing sensitivity

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

49

7.11 Functions in DMX mode 3Ch3 (model versions with RGB LEDs)

Channel Value Function

1 0 … 255 Intensity red (0 % to 100 %)
2 0 … 255 Intensity green (0 % to 100 %)
3 0 … 255 Intensity blue (0 % to 100 %)

7.12 Functions in DMX mode 4Ch (model versions with RGB LEDs)

Channel Value Function

1 0 … 255 Dimmer (0 % to 100 %)
2 Strobe

0 … 5 LEDs on, brightness controlled by channel 1
6 … 10 LEDs off (blackout)

Operating

LED floodlight

50

Channel Value Function

11 … 33 Random impulses, increasing speed
34 … 56 Randomly increasing brightness, increasing speed
57 … 79 Randomly decreasing brightness, increasing speed
80 … 102 Random Strobe effect, increasing speed
103 … 127 Interrupt effect, 5 s to 1 s
128 … 250 Strobe effect, speed increasing from approx. 0 Hz to 30 Hz
251 … 255 LEDs on, brightness controlled by channel 1

3 Colour macro

0 … 5 LEDs off (blackout)
6 … 13 Red
14 … 21 Amber
22 … 29 Warm yellow
30 … 37 Yellow

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

51

Channel Value Function

38 … 45 Green
46 … 53 Cyan
54 … 61 Cyan
62 … 69 Blue
70 … 77 Lavender
78 … 85 Mauve
86 … 93 Magenta
94 … 101 Pink
102 … 109 Warm white
110 … 117 White
118 … 125 Cold white
126 … 128 Ending colour change
129 … 192 Colour change, increasing speed

Operating

LED floodlight

52

Channel Value Function

193 … 255 Gradual colour change, increasing speed

3 Sound control

0 … 5 Sound control off
6 … 255 Sound control on, increasing sensitivity

7.13 Functions in DMX mode 5Ch (model versions with white LEDs)

Channel Value Function

1 0 … 255 Dimmer (0 % to 100 %)
2 Strobe

0 … 5 LEDs on, brightness controlled by channel 1
6 … 10 LEDs off (blackout)

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

53

Channel Value Function

11 … 33 Random impulses, increasing speed
34 … 56 Randomly increasing brightness, increasing speed
57 … 79 Randomly decreasing brightness, increasing speed
80 … 102 Random Strobe effect, increasing speed
103 … 127 Interrupt effect, 5 s to 1 s
128 … 250 Strobe effect, speed increasing from approx. 0 Hz to 30 Hz
251 … 255 LEDs on, brightness controlled by channel 1

3 Strobe programmes

0 … 5 No function
11 … 255 Automatic Strobe programmes with alternating segments

4 Process speed

11 … 255 Automatic Strobe programme speed, increasing if channel 5 = 0…5)

5 Sound control

Operating

LED floodlight

54

Channel Value Function

0 … 5 Sound control off
6 … 255 Sound control on, increasing sensitivity

7.14 Functions in DMX mode 6Ch (model versions with RGB LEDs)

Channel Value Function

1 0 … 255 Dimmer (0 % to 100 %)
2 Strobe

0 … 5 LEDs on, brightness controlled by channel 1
6 … 10 LEDs off (blackout)
11 … 33 Random impulses, increasing speed
34 … 56 Randomly increasing brightness, increasing speed

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

55

Channel Value Function

57 … 79 Randomly decreasing brightness, increasing speed
80 … 102 Random Strobe effect, increasing speed
103 … 127 Interrupt effect, 5 s to 1 s
128 … 250 Strobe effect, speed increasing from approx. 0 Hz to 30 Hz

251 … 255 LEDs on, brightness controlled by channel 1
3 0 … 255 Intensity red (0 % to 100 %)
4 0 … 255 Intensity green (0 % to 100 %)
5 0 … 255 Intensity blue (0 % to 100 %)
6 Sound control

0 … 5 Sound control off

6 … 255 Sound control on, increasing sensitivity

Operating

LED floodlight

56

7.15 Functions in DMX mode 7Ch (model version with 648 white LEDs)

Channel Value Function

1 0 … 255 Dimmer (0 % to 100 %)
2 Strobe

0 … 5 LEDs on

6 … 10 LEDs off (blackout)

11 … 250 Strobe effect, speed increasing from approx. 0 Hz to 30 Hz

251 … 255 LEDs on
3 Flash impulse

0 … 255 Flash impulse duration, increasing from 0 ms to 510 ms
4 0 … 255 Brightness of LED segment 1 (0 % to 100 %)
5 0 … 255 Brightness of LED segment 2 (0 % to 100 %)

Operating

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

57

Channel Value Function

6 0 … 255 Brightness of LED segment 3 (0 % to 100 %)
7 0 … 255 Brightness of LED segment 4 (0 % to 100 %)

Operating

LED floodlight

58

8 Technical specifications

Number of DMX channels 1, 2, 3, 4, or 6 channels, depending on operating mode
Illuminant 132 tricolour SMD LEDs, 0.2 W each
Beam angle approx. 75°
Operating supply voltage

100 - 240 V 50/60 Hz
Power consumption 30 W
Protection class IP20
Fuse 5 mm × 20 mm, 2 A, 250 V, slow-blow
Dimensions (W × H × D) 310 mm× 70 mm× 70 mm
Weight 1.05 kg

Stairville Wild Wash 132 LED
RGB DMX (item no. 399664)

Technical specifications

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

59

Number of DMX channels 1, 2 or 3 channels, depending on operating mode
Illuminant 132 SMD LEDs, cold white, 0.2 W each
Beam angle approx. 75°
Operating supply voltage

100 - 240 V 50/60 Hz
Power consumption 30 W
Protection class IP20
Fuse 5 mm × 20 mm, 2 A, 250 V, slow-blow
Dimensions (W × H × D) 310 mm× 70 mm× 70 mm
Weight 1.05 kg

Stairville Wild Wash 132 LED
White DMX (item no. 399663)

Technical specifications

LED floodlight

60

Number of DMX channels 1, 2, 3, 5, or 7 channels, depending on operating mode
Illuminant 648 tricolour SMD LEDs, 0.2 W each
Beam angle approx. 75°
Operating supply voltage

100 - 240 V 50/60 Hz
Power consumption 130 W
Protection class IP20
Fuse 5 mm × 20 mm, 2 A, 250 V, slow-blow
Dimensions (W × H × D) 335 mm× 182 mm× 93 mm
Weight 3.25 kg

Stairville Wild Wash 648 LED
RGB DMX (item no. 399658)

Technical specifications

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

61

Number of DMX channels 1, 2, 3, 4, or 6 channels, depending on operating mode
Illuminant 648 SMD LEDs, cold white, 0.2 W each
Beam angle approx. 75°
Operating supply voltage

100 - 240 V 50/60 Hz
Power consumption 130 W
Protection class IP20
Fuse 5 mm × 20 mm, 2 A, 250 V, slow-blow
Dimensions (W × H × D) 335 mm× 182 mm× 93 mm
Weight 3.25 kg

Stairville Wild Wash 648 LED
White DMX (item no. 399662)

Technical specifications

LED floodlight

62

9 Plug and connection assignments

This chapter will help you select the right cables and plugs to connect your valuable equip‐
ment so that a perfect light experience is guaranteed.

Please take our tips, because especially in ‘Sound & Light’ caution is indicated: Even if a plug
fits into a socket, the result of an incorrect connection may be a destroyed DMX controller, a
short circuit or ‘just’ a not working light show!

The unit offers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX input. Please
refer to the drawing and table below for the pin assignment of a suitable XLR plug.

Pin Configuration

1 Ground, shielding
2 Signal inverted (DMX–, ‘cold signal’)
3 Signal (DMX+, ‘hot signal’)

Introduction

DMX connections

Plug and connection assignments

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

63

10 Troubleshooting

NOTICE!
Possible data transmission errors

For error-free operation make use of dedicated DMX cables and do not use ordi‐
nary microphone cables.

Never connect the DMX input or output to audio devices such as mixers or ampli‐
fiers.

In the following we list a few common problems that may occur during operation. We give you
some suggestions for easy troubleshooting:

Troubleshooting

LED floodlight

64

Symptom Remedy

The unit does not work, no light,
the display is dark

Check the mains connection and the main fuse.

Apparently no function despite
proper power supply

Check if the unit is in DMX mode or in ‘slave’ mode. If so,

check the unit in another mode.
No response to the DMX con‐

troller

1. Check whether the DMX controller is switched on.

Check the DMX connectors and cables for proper con‐

nection.

2. Check the address settings and the DMX polarity.

3. Try using another DMX controller.

4. Check whether the DMX cables run near or parallel to

high-voltage cables that may cause damage or interfer‐

ence to a DMX interface circuit.

If the procedures recommended above do not succeed, please contact our Service Center. You
can find the contact information at www.thomann.de.

Troubleshooting

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

65

11 Cleaning

Clean the optical lenses, that are accessible from the outside, regularly in order to optimize the
light output. The frequency of cleaning depends on the operating environment: wet, smoky or
particularly dirty surroundings can cause more accumulation of dirt on the optics of the
device.

n Clean with a soft cloth using our lamp and lens cleaner (item no. 280122).
n Always dry the parts carefully.

The fan grids of the device must be cleaned on a regular basis to remove dust and dirt. Before
cleaning, switch off the device and disconnect AC-powered devices from the mains. Use a lint­free damp cloth for cleaning. Never use solvents or alcohol for cleaning.

Optical lenses

Fan grids

Cleaning

LED floodlight

66

12 Protecting the environment

For the transport and protective packaging, environmentally friendly materials have been
chosen that can be supplied to normal recycling.

Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose of these materials with your normal household waste, but make sure that

they are collected for recycling. Please follow the notes and markings on the packaging.

This product is subject to the European Waste Electrical and Electronic Equipment Directive
(WEEE). Do not dispose with your normal household waste.

Dispose of this device through an approved waste disposal firm or through your local waste
facility. When discarding the device, comply with the rules and regulations that apply in your
country. If in doubt, consult your local waste disposal facility.

Disposal of the packaging mate‐
rial

Disposal of your old device

Protecting the environment

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

67

Notes

LED floodlight

68

Notes

Wild Wash 132 LED RGB DMX, Wild Wash 132 LED White DMX,

Wild Wash 648 LED RGB DMX, Wild Wash 648 LED White DMX

69

Notes

LED floodlight

70

Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.de