Page 1
Dr. RDM I DMX RDM
Tester
controller
User manual
Page 2
Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: +49 (0) 9546 9223-0
E-mail: info@thomann.de
Internet: www.thomann.de
20.02.2018, ID: 421279
Page 3
Table of contents
1 General notes............................................................................................................................................... 6
1.1 Further information........................................................................................................................... 7
1.2 Notational conventions.................................................................................................................... 8
1.3 Symbols and signal words............................................................................................................... 9
2 Safety instructions.................................................................................................................................. 11
3 Features....................................................................................................................................................... 13
4 Installation and starting up................................................................................................................ 14
5 Connections and controls................................................................................................................... 15
6 Operating.................................................................................................................................................... 18
6.1 Main menu.......................................................................................................................................... 19
6.2 DMX 512 test...................................................................................................................................... 20
6.3 RDM test.............................................................................................................................................. 34
6.4 MIDI test.............................................................................................................................................. 63
6.5 Cable test............................................................................................................................................ 65
6.6 System settings................................................................................................................................. 68
Table of contents
Dr. RDM I DMX RDM Tester
3
controller
Page 4
7 Technical specifications....................................................................................................................... 73
8 Plug and connection assignment.................................................................................................... 74
9 Protecting the environment.............................................................................................................. 76
Table of contents
4
Dr. RDM I DMX RDM Tester
controller
Page 5
Dr. RDM I DMX RDM Tester
5
controller
Page 6
1 General notes
This manual contains important instructions for the safe operation of the unit. Read and follow
the safety instructions and all other instructions. Keep the manual for future reference. Make
sure that it is available to all those using the device. If you sell the unit please make sure that
the buyer also receives this manual.
Our products are subject to a process of continuous development. Thus, they are subject to
change.
General notes
6
Dr. RDM I DMX RDM Tester
controller
Page 7
1.1 Further information
On our website (www.thomann.de) you will find lots of further information and details on the
following points:
Download This manual is also available as PDF file for you to download.
Keyword search
Use the search function in the electronic version to find the topics of
interest for you quickly.
Online guides
Our online guides provide detailed information on technical basics
and terms.
Personal consultation For personal consultation please contact our technical hotline.
Service
If you have any problems with the device the customer service will
gladly assist you.
General notes
Dr. RDM I DMX RDM Tester
7
controller
Page 8
1.2 Notational conventions
This manual uses the following notational conventions:
The letterings for connectors and controls are marked by square brackets and italics.
Examples: [VOLUME] control, [Mono] button.
Texts and values displayed on the device are marked by quotation marks and italics.
Examples: ‘24ch’ , ‘OFF’.
Letterings
Displays
General notes
8
Dr. RDM I DMX RDM Tester
controller
Page 9
The individual steps of an instruction are numbered consecutively. The result of a step is
indented and highlighted by an arrow.
Example:
1. Switch on the device.
2. Press [Auto].
ð
Automatic operation is started.
3. Switch off the device.
1.3 Symbols and signal words
In this section you will find an overview of the meaning of symbols and signal words that are
used in this manual.
Instructions
General notes
Dr. RDM I DMX RDM Tester
9
controller
Page 10
Signal word Meaning
DANGER! This combination of symbol and signal word indicates an
immediate dangerous situation that will result in death or
serious injury if it is not avoided.
NOTICE! This combination of symbol and signal word indicates a pos-
sible dangerous situation that can result in material and
environmental damage if it is not avoided.
Warning signs Type of danger
Warning – danger zone.
General notes
10
Dr. RDM I DMX RDM Tester
controller
Page 11
2 Safety instructions
This device is for testing devices that are controlled via DMX, RDM or MIDI or output these signals. Use the device only as described in this user manual. Any other use or use under other
operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sufficient physical, sensorial, and intellectual
abilities and having corresponding knowledge and experience. Other persons may use this
device only if they are supervised or instructed by a person who is responsible for their safety.
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from
the unit. They could swallow the pieces and choke!
Never let children unattended use electrical devices.
Intended use
Safety
Safety instructions
Dr. RDM I DMX RDM Tester
11
controller
Page 12
NOTICE!
External power supply
The device is powered by an external power supply. Before connecting the
external power supply, ensure that the input voltage (AC outlet) matches the
voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker. Failure to do so could result in damage to the device and possibly the user.
Unplug the external power supply before electrical storms occur and when the
device is unused for long periods of time to reduce the risk of electric shock or
fire.
NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never
expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and
strong vibrations.
Safety instructions
12
Dr. RDM I DMX RDM Tester
controller
Page 13
3 Features
n Universal test device for DMX, RDM and MIDI networks
n
5-pin DMX in and output
n
Plug-in power supply and adapter for 3-pin DMX plug included
n
Operating via buttons and display on the unit
Features
Dr. RDM I DMX RDM Tester
13
controller
Page 14
4 Installation and starting up
Unpack and carefully check that there is no transportation damage before using the unit. Keep
the equipment packaging. To fully protect the device against vibration, dust and moisture
during transportation or storage use the original packaging or your own packaging material
suitable for transport or storage, respectively.
Create all connections while the device is off. Use the shortest possible high-quality cables for
all connections. Take care when running the cables to prevent tripping hazards.
The included lanyard can be threaded through the bottom of the device.
Installation and starting up
14
Dr. RDM I DMX RDM Tester
controller
Page 15
5 Connections and controls
Connections and controls
Dr. RDM I DMX RDM Tester
15
controller
Page 16
1 Jog Wheel for control and menu selection
2 Display
The display is turned off after an adjustable period of time without keystroke. Press the jog wheel to reactivate the
display.
3 [DMX/RDM OUT]
5-pin DMX / RDM output
4 [DMX/RDM IN]
5-pin DMX / RDM input
5 [MIDI IN]
MIDI input
6 [Power Switch]
Main switch. Turns the device on and off.
Connections and controls
16
Dr. RDM I DMX RDM Tester
controller
Page 17
7 [PWR]
The LED indicates that the device is switched on.
8 [Program Update]
Micro SD slot
9 [Under Voltage]
This LED lights up when the supply voltage is too low.
10 [Normal]
The LED indicates that the supply voltage is within the permissible range.
11 [DC INPUT]
Connector for the supplied power supply adapter.
Connections and controls
Dr. RDM I DMX RDM Tester
17
controller
Page 18
6 Operating
Connect the supplied mains adapter to the power supply input of the device and then plug
the adapter into an AC outlet.
Operating
18
Dr. RDM I DMX RDM Tester
controller
Page 19
6.1 Main menu
1. Turn the jog wheel to highlight a menu item.
2. Press the jog wheel to select the highlighted menu item.
3. Press the jog wheel again to open the associated submenu.
4. The display shows the available elements of the submenu.
5. Select the menu item ‘EXIT’ and press the jog wheel to return to the main menu.
Selection in main menu
Operating
Dr. RDM I DMX RDM Tester
19
controller
Page 20
6.2 DMX 512 test
This menu allows you to monitor the data packets being received by DMX-controlled devices
or sending test data to the devices.
Operating
20
Dr. RDM I DMX RDM Tester
controller
Page 21
1. Select the item ‘DMX-512 TEST’ from the main menu.
2. Press the jog wheel to open the respective submenu.
ð
The display shows:
3. Select one of the submenus ‘DMX Packet Test’ , ‘DMX Data Receive’ or ‘DMX Data Send’.
Operating
Dr. RDM I DMX RDM Tester
21
controller
Page 22
1. Select the item ‘DMX Packet Test’ from the submenu ‘DMX-512 Test’.
2. Press the jog wheel to open the respective submenu.
ð
If the wiring is correct and a DMX signal is received, the display shows the following
values:
If no signal is received, the display shows:
DMX packet test
Operating
22
Dr. RDM I DMX RDM Tester
controller
Page 23
In this case, check the wiring and the correct fit of the connectors.
3. To return to the parent menu, select ‘EXIT’ and press the jog wheel to confirm.
Operating
Dr. RDM I DMX RDM Tester
23
controller
Page 24
1. Select the item ‘DMX Data Receive’ from the submenu ‘DMX-512 Test’.
2. Press the jog wheel to open the respective submenu.
ð
The display shows:
It will display the received DMX value (‘000’ …‘255’) for every 25 channels.
3. To change the first displayed channel, use the jog wheel to select ‘Start’ and press the
jog wheel. Turn the jog wheel until the number of the desired channel appears at ‘Start’ .
Press the jog wheel to confirm.
Analysis of received DMX data
Operating
24
Dr. RDM I DMX RDM Tester
controller
Page 25
4. To change the display format, use the jog wheel to select ‘Format’ and press the jog
wheel. Turn the jog wheel to select one of the following formats.
n ‘DEC’ : Decimal values
n
‘PER’ : Percentage values
n
‘BAR’ : Bars of squares
n
‘RGB’ : Squares with RGB colour mixing
n
‘BRG’ : Squares with BGR colour mixing
n
‘HEX’ : Hexadecimal values
Press the jog wheel.
5. To return to the parent menu, select ‘EXIT’ and press the jog wheel to confirm.
Operating
Dr. RDM I DMX RDM Tester
25
controller
Page 26
1. Select the item ‘DMX Data Send’ from the submenu ‘DMX-512 TEST’.
2. Press the jog wheel to open the respective submenu.
ð
The display shows:
3. Select the item ‘Single Channel Mode’ from the submenu ‘DMX-512 SEND’.
4. Press the jog wheel to open the respective submenu.
ð
The display shows:
Analysis of transmitted DMX
data
Operating
26
Dr. RDM I DMX RDM Tester
controller
Page 27
5. To select the channel on which the data should be sent, select the item ‘Channel’ . Press
the jog wheel. Use the jog wheel to set a value between 1 and 512 – or ‘All’ for transmission on all channels.
6. To select an operating mode, select ‘Mode’ . Press the jog wheel. Use the jog wheel to
select one of the following options:
n ‘Fader Only’ : The transmitted DMX value can be adjusted between 0 and 255 with
the jog wheel.
n
‘Auto ON/OFF’ : The transmitted DMX value automatically changes at the set speed
n
‘Ramping’ : The transmitted DMX value rises evenly with the set speed, then the
process repeats itself
Operating
Dr. RDM I DMX RDM Tester
27
controller
Page 28
n ‘Stop’ : The transmitted DMX value can not be changed
7. To select the value range of the data transmitted, select the item ‘Channel Level’ . Press
the jog wheel. Use the jog wheel to set a value between 0 and 255.
8. To set the rate of change, select ‘Speed’ . Press the jog wheel. Use the jog wheel to set a
value between ‘level 0’ and ‘level 10’.
9. To return to the parent menu, select ‘EXIT’ and press the jog wheel to confirm.
10. Select the item ‘Multiple Channel Mode’ from the submenu ‘DMX-512 SEND’.
11. Press the jog wheel to open the respective submenu.
ð
The display shows:
Operating
28
Dr. RDM I DMX RDM Tester
controller
Page 29
12. To change the first channel for which DMX values are to be sent, use the jog wheel to
select ‘Start/Channel’ and press the jog wheel. Turn the jog wheel until the number of
the desired channel appears at ‘Start’ . Press the jog wheel to confirm.
13. To set the transmitted DMX value in the range 0 to 255, first select the value with the jog
wheel. Press the jog wheel. Set the desired value with the jog wheel. Press the jog wheel.
14. To change the display format, use the jog wheel to select ‘Format’ and press the jog
wheel. Turn the jog wheel to select one of the following formats.
n ‘DEC’ : Decimal values
n
‘PER’ : Percentage values
Operating
Dr. RDM I DMX RDM Tester
29
controller
Page 30
n ‘BAR’ : Bars of squares
n
‘HEX’ : Hexadecimal values
Press the jog wheel.
15. To reset the transmitted DMX value, use the jog wheel to select the item ‘All Reset’ and
press the jog wheel.
16. To return to the parent menu, select ‘EXIT’ and press the jog wheel to confirm.
17. Select the item ‘Color Demo Mode’ from the submenu ‘DMX-512 SEND’.
18. Press the jog wheel to open the respective submenu.
ð
The display shows:
Operating
30
Dr. RDM I DMX RDM Tester
controller
Page 31
19. Use the jog wheel to select the setting to be changed and press the jog wheel. Turn the
jog wheel to select or adjust a value. The following table shows the menu items and
choices.
Menu item Choices Meaning
‘Pixel Type’ ‘8Bit’ , ‘16Bit’ Resolution of connected devices
‘Start Channel’ ‘1’ …‘512’ First channel for which DMX values are to be sent
‘Master Level’ ‘0’ …‘255’ Maximum DMX value
Operating
Dr. RDM I DMX RDM Tester
31
controller
Page 32
Menu item Choices Meaning
‘Speed’ ‘Level0’ …‘Level10’ Running speed
‘Fade Time’ ‘0 %’ … ‘100 %’ Fade time
20. To return to the parent menu, select ‘EXIT’ and press the jog wheel to confirm.
21. Select the item ‘Chase Demo Mode’ from the submenu ‘DMX-512 SEND’.
22. Press the jog wheel to open the respective submenu.
ð
The display shows:
Operating
32
Dr. RDM I DMX RDM Tester
controller
Page 33
23. Use the jog wheel to select the setting to be changed and press the jog wheel. Turn the
jog wheel to select or adjust a value. The following table shows the menu items and
choices.
Menu item Choices Meaning
‘Start Chan.’ ‘1’ …‘512’ First channel for which DMX values are to be sent
‘Master’ ‘0’ …‘255’ Maximum DMX value
‘Pixel Type’ ‘8Bit’ , ‘16Bit’ Resolution of connected devices
‘Total Pixel’ ‘1’ …‘512’ Number of connected devices
‘Pixel Group’ Value within the range of
‘Total Pixel’
Number of devices in a group
‘Jump Pixel’ Value within the range of ‘Pixel
Group’
Number of devices that will be switched within the group
‘Test Color’ ‘Color 1’ , ‘All’ Number of colours of the spotlight to be tested
‘Speed level’ ‘Level0’ … ‘Level10’, ‘Manual’ Process speed
‘Fade Time’ ‘0 %’ … ‘100 %’ Fade time
24. To return to the parent menu, select ‘EXIT’ and press the jog wheel to confirm.
Operating
Dr. RDM I DMX RDM Tester
33
controller
Page 34
25. To return to the main menu, select ‘EXIT’ again and press the jog wheel to confirm.
6.3 RDM test
This menu allows you to retrieve information about the connected RDM-controlled devices or
send test data to the devices.
Operating
34
Dr. RDM I DMX RDM Tester
controller
Page 35
1. Select the item ‘RDM DATA TEST’ from the main menu.
2. Press the jog wheel to open the respective submenu.
ð
The display shows:
3. Select one of the submenus ‘Get&Set RDM Parameter’ or ‘Update RDM Device’.
Operating
Dr. RDM I DMX RDM Tester
35
controller
Page 36
1. Select the item ‘Get&Set RDM Parameter’ from the submenu ‘RDM DATA TEST’.
2. Press the jog wheel to open the respective submenu.
ð
The display shows:
If the wiring is correct and an RDM-controlled device is found, the display shows
real-time information about the device:
Retrieve RDM parameters - Identify Device
Operating
36
Dr. RDM I DMX RDM Tester
controller
Page 37
If no signal is received, the display shows:
Operating
Dr. RDM I DMX RDM Tester
37
controller
Page 38
In this case, check the wiring and the correct fit of the connectors.
3. For more detailed information, use the jog wheel to select ‘Para’ . Press the jog wheel.
ð
The display shows:
Operating
38
Dr. RDM I DMX RDM Tester
controller
Page 39
4. The selectable parameters depend on the respective device, examples: ‘Identify Device’ ,
‘Device Info’ , ‘DMX Start Address’.
5. To retrieve a parameter, select it with the jog wheel and press the jog wheel. Select ‘Get
Parameter’ and press the jog wheel.
ð
The display shows, for example:
Operating
Dr. RDM I DMX RDM Tester
39
controller
Page 40
6. Use the jog wheel to select ‘Fresh’ to refresh the displayed information, or ‘EXIT’ to
return to the parent menu. Press the jog wheel.
Operating
40
Dr. RDM I DMX RDM Tester
controller
Page 41
1. Select the item ‘Get&Set RDM Parameter’ from the submenu ‘RDM DATA TEST’.
2. Press the jog wheel to open the respective submenu.
ð
The display shows:
If the wiring is correct and an RDM-controlled device is found, the display shows
real-time information about the device:
Retrieve RDM Device Information - Device Info
Operating
Dr. RDM I DMX RDM Tester
41
controller
Page 42
If no signal is received, the display shows:
Operating
42
Dr. RDM I DMX RDM Tester
controller
Page 43
In this case, check the wiring and the correct fit of the connectors.
3. For more detailed information, use the jog wheel to select ‘Para’ . Press the jog wheel.
ð
The display shows:
Operating
Dr. RDM I DMX RDM Tester
43
controller
Page 44
4. The selectable parameters depend on the respective device, examples: ‘Identify Device’ ,
‘Device Info’ , ‘DMX Start Address’.
5. To retrieve a parameter, select it with the jog wheel and press the jog wheel. Select ‘Get
Parameter’ and press the jog wheel.
ð
The display shows, for example:
Operating
44
Dr. RDM I DMX RDM Tester
controller
Page 45
6. Use the jog wheel to select ‘More Info’ to access further parameters.
7. Use the jog wheel to select ‘Fresh’ to refresh the displayed information, or ‘EXIT’ to
return to the parent menu. Press the jog wheel.
Operating
Dr. RDM I DMX RDM Tester
45
controller
Page 46
1. Select the item ‘Get&Set RDM Parameter’ from the submenu ‘RDM DATA TEST’.
2. Press the jog wheel to open the respective submenu.
ð
The display shows:
If the wiring is correct and an RDM-controlled device is found, the display shows
real-time information about the device:
Changing RDM parameters
Operating
46
Dr. RDM I DMX RDM Tester
controller
Page 47
If no signal is received, the display shows:
Operating
Dr. RDM I DMX RDM Tester
47
controller
Page 48
In this case, check the wiring and the correct fit of the connectors.
3. To change individual parameters, use the jog wheel to select ‘Para’ . Press the jog wheel.
ð
The display shows:
Operating
48
Dr. RDM I DMX RDM Tester
controller
Page 49
4. The selectable parameters depend on the respective device, examples: ‘Identify Device’ ,
‘Device Info’ , ‘DMX Start Address’.
5. To retrieve a parameter, select it with the jog wheel and press the jog wheel. Select ‘Set
Parameter’ and press the jog wheel.
ð
The display shows, for example:
Operating
Dr. RDM I DMX RDM Tester
49
controller
Page 50
6. Use the jog wheel to select ‘Start Identify’ to start or ‘Stop Identify’ to stop the identifica-
tion. Press the jog wheel.
7. To select which devices should be affected by the change, use the Jog Wheel to select
‘Only self’ and press the jog wheel. Turn the jog wheel to select one of the following for-
mats.
n ‘Only Self’ : Change only affects the selected device
n
‘Same mfrs’ : Change affects all devices from the same manufacturer as the selected
device
n
‘All Device’ : Change affects all connected devices
Operating
50
Dr. RDM I DMX RDM Tester
controller
Page 51
Press the jog wheel.
8. Use the jog wheel to select ‘Ok&Save’ and press the jog wheel to save the change.
9. Use the jog wheel to select ‘EXIT’ to return to the parent menu. Press the jog wheel.
Operating
Dr. RDM I DMX RDM Tester
51
controller
Page 52
1. Select the item ‘Get&Set RDM Parameter’ from the submenu ‘RDM DATA TEST’.
2. Press the jog wheel to open the respective submenu.
ð
The display shows:
If the wiring is correct and an RDM-controlled device is found, the display shows
real-time information about the device:
Display or change of the DMX
address of an RDM-controlled
device
Operating
52
Dr. RDM I DMX RDM Tester
controller
Page 53
If no signal is received, the display shows:
Operating
Dr. RDM I DMX RDM Tester
53
controller
Page 54
In this case, check the wiring and the correct fit of the connectors.
3. To change individual parameters, use the jog wheel to select ‘Para’ . Press the jog wheel.
ð
The display shows:
Operating
54
Dr. RDM I DMX RDM Tester
controller
Page 55
4. Use the jog wheel to select ‘Para: DMX Start Address’ and press the jog wheel.
5. To display the current DMX address, select ‘Get Parameter’ and press the jog wheel.
ð
The display shows, for example:
Operating
Dr. RDM I DMX RDM Tester
55
controller
Page 56
6. Use the jog wheel to select ‘Fresh’ to refresh the displayed information, or ‘EXIT’ to
return to the parent menu. Press the jog wheel.
7. To change the DMX address, use the jog wheel to select ‘Set Parameter’ and press the
jog wheel.
ð
The display shows, for example:
Operating
56
Dr. RDM I DMX RDM Tester
controller
Page 57
8. Use the jog wheel to select ‘Channel:’ and press the jog wheel.
Set the desired value with the jog wheel. Press the jog wheel to confirm.
9. To select which devices should be affected by the change, use the Jog Wheel to select
‘Only self’ and press the jog wheel. Turn the jog wheel to select one of the following for-
mats.
n ‘Only Self’ : Change only affects the selected device
n
‘Same mfrs’ : Change affects all devices from the same manufacturer as the selected
device
n
‘All Device’ : Change affects all connected devices
Operating
Dr. RDM I DMX RDM Tester
57
controller
Page 58
Press the jog wheel.
10. Use the jog wheel to select ‘Ok&Save’ and press the jog wheel to save the change.
11. Use the jog wheel to select ‘EXIT’ to return to the parent menu. Press the jog wheel.
Operating
58
Dr. RDM I DMX RDM Tester
controller
Page 59
1. Select the item ‘Update RMD device’ from the submenu ‘RDM DATA TEST’.
2. Press the jog wheel to open the respective submenu.
ð
The display shows:
If the wiring is correct and an RDM-controlled device is found, the display shows
real-time information about the device:
Software update of an RDM-controlled device
Operating
Dr. RDM I DMX RDM Tester
59
controller
Page 60
If no signal is received, the display shows:
Operating
60
Dr. RDM I DMX RDM Tester
controller
Page 61
In this case, check the wiring and the correct fit of the connectors.
3. Insert a micro SD card with the required software into the micro SD slot of the device.
4. Use the jog wheel to select ‘Send: Single device’ . Press the jog wheel.
ð
The display shows:
Operating
Dr. RDM I DMX RDM Tester
61
controller
Page 62
5. To retrieve a parameter, select it with the jog wheel and press the jog wheel. Select
‘Single device’ (transmission to one device) or ‘All devices’ (transmission to all devices)
and press the jog wheel.
ð
The software is transferred to the devices.
6. Use the jog wheel to select ‘EXIT’ to return to the parent menu. Press the jog wheel.
Operating
62
Dr. RDM I DMX RDM Tester
controller
Page 63
6.4 MIDI test
This menu allows you to test the data of a MIDI-controlled device.
1. Connect a MIDI device to the MIDI input.
2. Select the item ‘MIDI Receive’ from the main menu.
Operating
Dr. RDM I DMX RDM Tester
63
controller
Page 64
3. Press the jog wheel to open the respective submenu.
ð
The display shows:
Operating
64
Dr. RDM I DMX RDM Tester
controller
Page 65
After a few seconds, the ‘ACT’ indicator appears in the lower left corner of the display. Once the data has been received from a MIDI device, the display shows:
4. To return to the parent menu, select ‘EXIT’ and press the jog wheel to confirm.
6.5 Cable test
This menu allows you to test a DMX cable.
Operating
Dr. RDM I DMX RDM Tester
65
controller
Page 66
1. Connect the cable to be tested to the DMX input and the DMX output.
2. Select the item ‘CABLE TEST’ from the main menu.
3. Press the jog wheel to open the respective submenu.
ð
The display shows:
Operating
66
Dr. RDM I DMX RDM Tester
controller
Page 67
4. Use the jog wheel to select ‘Test’ and press the jog wheel.
ð
After a few seconds, the display shows the test result. If all wires are correctly connected, the display shows:
5. To repeat the test, select ‘Try Again’ and press the jog wheel to confirm.
6. To return to the parent menu, select ‘EXIT’ and press the jog wheel to confirm.
Operating
Dr. RDM I DMX RDM Tester
67
controller
Page 68
6.6 System settings
In this menu, you can adjust device settings.
Operating
68
Dr. RDM I DMX RDM Tester
controller
Page 69
1. Select the item ‘SYSTEM Setup’ from the main menu.
2. Press the jog wheel to open the respective submenu.
ð
The display shows:
Operating
Dr. RDM I DMX RDM Tester
69
controller
Page 70
Turn the jog wheel to scroll down the list:
Operating
70
Dr. RDM I DMX RDM Tester
controller
Page 71
3. Use the jog wheel to select the setting to be changed and press the jog wheel. Turn the
jog wheel to select or adjust a value. The following table shows the menu items and
choices.
Menu item Choices Meaning
‘TX Start Code’ ‘0’ …‘255’ Start value for the DMX data transmission.
‘RX Start Code’ ‘0’…‘255’, ‘All’ This code is required if several test devices should work as trans-
mitters. In this case, all test devices must be set to the same
code. If you select ‘All’ , the device accepts all start codes.
‘Auto Identify’ ‘Auto’ Automatically sending a request for identification to all con-
nected devices when selecting the menu item ‘Get&Set RDM
Parameter’ .
‘OFF’ No automatic request for identification.
‘16bit Format’ ‘MSB first’ In 16-bit mode: higher-value byte first
‘LSB first’ In 16-bit mode: higher-value byte last
‘Format’ ‘Decimal’ , ‘Percents’, ‘BAR
(square)’ , ‘Hexadezimal’
Selection of the display format for numerical values: decimal,
percentage, as a bar or hexadecimal
‘Contrast Level’ ‘10’ …‘100’ Display contrast setting
Operating
Dr. RDM I DMX RDM Tester
71
controller
Page 72
Menu item Choices Meaning
‘Backlight Off’ ‘30 sec’, ‘1 min’, ‘5 min’, ‘10
min’ , ‘30 min’
Setting the time after which the display turns off automatically.
‘Auto Mask Device’ ‘ON’ A connected RDM-controlled device does not appear in the
overview. If you set its DMX address, the other devices without
DMX address appear in the overview.
‘OFF’ A connected RDM-controlled device appears in the overview.
‘DMX Output When RDM’ ‘ON’ DMX signals can also be sent in RDM mode.
‘OFF’ No DMX signals are sent in RDM mode.
‘DMX Output Level’ ‘0’ …‘255’ Maximum DMX output level if the option ‘DMX Output When
RDM’ is set to ‘ON’.
4. Select ‘OK&Save’ and press the jog wheel to confirm.
ð
The values are saved.
5. To return to the parent menu, select ‘EXIT’ and press the jog wheel to confirm.
Operating
72
Dr. RDM I DMX RDM Tester
controller
Page 73
7 Technical specifications
Voltage supply
Plug-in power supply (9 V / 500 mA ), positive pole via inner contact
Dimensions (W × H × D) 170 mm × 100 mm × 40 mm (15.35in. × 15.55in. × 5.31in.)
Weight 0.28 kg
Technical specifications
Dr. RDM I DMX RDM Tester
73
controller
Page 74
8 Plug and connection assignment
This chapter will help you select the right cables and plugs to connect your valuable equipment so that a perfect light experience is guaranteed.
Please take our tips, because especially in ‘Sound & Light’ caution is indicated: Even if a plug
fits into a socket, the result of an incorrect connection may be a destroyed DMX controller, a
short circuit or ‘just’ a not working light show!
The unit offers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX input. Please
refer to the drawing and table below for the pin assignment of a suitable XLR plug.
Pin Configuration
1 Ground, shielding
2 Signal inverted (DMX–, ‘cold signal’)
3 Signal (DMX+, ‘hot signal’)
Introduction
DMX connections
Plug and connection assignment
74
Dr. RDM I DMX RDM Tester
controller
Page 75
A five-pin XLR socket serves as DMX output, a five-pin XLR plug serves as DMX input. The
drawing below and the table show the pin assignment of a matching coupling.
Pin Assignment
1 Ground (shielding)
2 Signal inverted (DMX–, ‘cold’)
3 Signal (DMX+, ‘hot’)
4 unused / second connection (DMX–)
5 unused / second connection (DMX+)
DMX connections
Plug and connection assignment
Dr. RDM I DMX RDM Tester
75
controller
Page 76
9 Protecting the environment
For the transport and protective packaging, environmentally friendly materials have been
chosen that can be supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose of these materials with your normal household waste, but make sure that
they are collected for recycling. Please follow the notes and markings on the packaging.
This product is subject to the European Waste Electrical and Electronic Equipment Directive
(WEEE) in its currently valid version. Do not dispose with your normal household waste.
Dispose of this device through an approved waste disposal firm or through your local waste
facility. When discarding the device, comply with the rules and regulations that apply in your
country. If in doubt, consult your local waste disposal facility.
Disposal of the packaging material
Disposal of your old device
Protecting the environment
76
Dr. RDM I DMX RDM Tester
controller
Page 77
Notes
Dr. RDM I DMX RDM Tester
77
controller
Page 78
Notes
78
Dr. RDM I DMX RDM Tester
controller
Page 79
Page 80
Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.de
Loading...