Thinklogical VX320 Quick Start Guide
The VX320 Router Critical Hardware Alarms: (Located at the top, left rear of the unit.)
QUICK-START GUIDE
QUICK-START GUIDE
As used with the Velocitydvi-3 and the Velocitykvm-4
Fiber Extension Systems
STEP 8: Connect the four supplied AC Power
Cords (PWR-0000056-R) to the receptacles
Single Head DVI & KVM
Source
USB
2.0
PWR
CP
CLINK
L1
FOL
DVI IN
L1 L2
DVI IN
L2
Velocitykvm-4
DVI OUT
L1: Video 1 and Data Tx to Rx
L2: Data Rx to Tx
SER IAL PORT
5
Audio OUT►
◄Audio IN
PS/2 (Mouse)
PS/2 (Keyboard)
USB 1.1 (Keyboard / Mouse)
STEP 6: Connect your KMASS
devices from the Source CPU to
the appropriate VelocityKVM
Transmitter ports.
Single Head DVI Source
6
located on the VX320's power supplies. Plug
each of them into a standard AC source. Verify
that all system functions are operating properly.
Optional
local USB
or PS/2
Keyboard &
Mouse
FROM CPU
UPDATES
HOST
USB 1.1
CNTRL
DEV
USB HID
VEL-U00M04-SCTX
Transmitter
P
S
LINE IN
2
HID
MIC OUT
LOCAL
Local DVI
(optional)
STEP 5: Connect the DVI IN cable
from the CPU to the VelocityKVM
Transmitter. Connect the DVI
OUT cable from the Transmitter to
the local monitor.
Local DVI
3
*
8
Power supplies, Left to Right:
*
1 Upper Card Cage Primary
2 Upper Card Cage Back-up
3 Lower Card Cage Primary
4 Lower Card Cage Back-up
STEP 4: Ensure the VelocityKVM
Transmitter’s ON/OFF switch is in the
OFF (0) position. Connect the AC
Power Cord and plug it into a standard
AC source. Turn the switch ON.
STEP 3: Connect your Velocity
Transmitter to the VX320 using
multi-mode fiber-optic cables (up
to 1000 meters). Connect L1 to
any Receive Port of the Upper
Card Cage. Connect L2 to the
same numbered Transmit Port of
the Lower Card Cage . (See the
Digital Crosspoint Switch detail
diagram, below right.)
4
router
VX320
KVM Matrix Switch
VX320 Router KVM Matrix Switch Chassis, 24 Rack Units, 1700 Watts
UPPER CARD CAGE
L1
L1
LOWER CARD CAGE
CONSOLE
ACT
RESET
FAULT
L
A
N
RS232
CONTROLLER
CONSOLE
ACT
RESET
FAULT
L
A
N
RS232
CONTROLLER
1
2
3
4
5
6
7
8
9
10
11
12
POWER SUPPLY 1 (LEFT):
POWER SUPPLY 2:
POWER SUPPLY 3:
POWER SUPPLY 4 (RIGHT):
Individual fan monitoring
FANS:
TEMPERATURE WARNING:
TEMPERATURE SHUTDOWN:
Card failure (Only with a redundant card)
CPU:
INPUT/OUTPUT CARDS:
ANY OF THE ABOVE
COMMON
GROUND
Single Head DVI & KVM Destination
STEP 1: Connect your Velocity Receiver to the VX320
using multi-mode fiber-optic cables (up to 1000 meters).
Connect cable L1* to any Transmit Port on any card of
the Upper Card Cage. Connect cable L2 to the same
numbered Receive Port of the Lower Card Cage. (See
the Digital Crosspoint Switch detail diagram, below left.)
*When using Velocity Extenders, fiber L1 carries Video
and Data and is treated as a Video Fiber.
L1
L1
7
Linux Operating System
STEP 7: Connect the
Controller Cards’ LAN
Ports to your Linux CPU
with CAT5 cables.
(CPU IP address:
192.168.13.9)
Primary Controller Card
(IP address: 192.168.13.15)
Optional Secondary
Controller Card
(IP address: 92.168.13.16)
Fan failure, temperature spikes, DC voltage and/or current out of range, AC power input interruption or module removed
Fan failure, temperature spikes, DC voltage and/or current out of range, AC power input interruption or module removed
Fan failure, temperature spikes, DC voltage and/or current out of range, AC power input interruption or module removed
Fan failure, temperature spikes, DC voltage and/or current out of range, AC power input interruption or module removed
Chassis over temperature, multiple sensors
Chassis over temperature causing shutdown
SFP+ failure, laser output fault
Powered by
MRTS Technology
CONTENTS
Upon receiving your
Thinklogical’s™ VX320 KVM Matrix Switch features
redundant Power Supplies and Fail-Over Controller
Modules for uninterrupted performance, even during
Thinklogical™ VX320 KVM
Matrix Switch you should
find the following items:
system reconfiguration, updates or debug. The
VX320 remains fully functional with only one of the
two Upper or Lower Card Cage Power Supplies
installed or with one Controller activated.
· VX320 Chassis & Cards
· LC Duplex Bulkhead with
Flange
· 15' CAT5 Cable (1)
NOTE: When using a single Controller, the upper
module (Primary) must be installed.
STEP 2: Ensure that the Receiver’s ON/OFF
switch is in the OFF (0) position. Depending on
devices (monitors, keyboard, mouse, etc.) to the
VelocityKVM Receiver using standard cables
as shown in the example below. Turn all the
devices ON. Insert the AC power cord into the
Receiver and plug it into a standard AC source.
1
L1 L2
· AC Power Cord (4)
· Product Manual CD
your configuration, connect your desktop
Turn the unit ON.
AUDIO
2
Velocitykvm-4
PWR
FOL
USB 2.0
DVI OUT
DDC
L2
L1
DVI OUT DDC
DVI OUT
DVI OUT
SER IAL PORT
U
LINE OUT
MIC IN
PS/2 or USB connectors
P
S
2
USB HID
P
D
HOST
A
T
E
USB 1.1
S
CNTRL
VEL-U00M04-SCRX
Receiver
DVI
STEP 5: Connect the DVI
from CPU cable from the
CPU to the VelocityDVI
5
Transmitter.
Power Supply
(PWR-000022-R)
4
DVI
DVI to Local Display DVI from CPU
dvi
Transmitter
Velocity
Digital Video Extension System – 3
Powered by
Video/Data
▲▼
L1
L1 L2
STEP 4: Connect the 5VDC
Power Supply and plug it into a
standard AC source.
6
MRTS Technology
Velocity
VEL-3 DVI
Transmitter
Data
L2
L2: Data Rx to Tx
L1: Video 1 and Data Tx to Rx
STEP 6: Connect the DVI to Local Display
cable from the VelocityDVI Transmitter
to your local monitor (optional).
STEP 3: Connect your VelocityDVI-3
Transmitter to the VX320 using multi-
dvi
mode fiber-optic cables (up to 1000
meters). Connect L1 to any Receive Port
of the Upper Card Cage and L2 to the
same numbered Transmit Port of the
Lower Card Cage. (See the Digital
Crosspoint Switch detail diagram, right.)
3
L2
Video/Data
from Tx
*Both the Upper and Lower Card Cages are designed to handle either Video or Data signals.
Upper Card Cage*
T
Crosspoint
Switch
R
Any Card 1-20,
any Port pair 1-16
Video/Data
to Rx
Data to Tx
Lower Card Cage*
T
Crosspoint
Switch
R
Any Card 1-20,
any Port pair 1-16
L2
L2
Data from Rx
Single Head DVI Destination
STEP 2: Connect the 5VDC Power Supply and plug it into a
standard AC source. Connect your display devices to the
VelocityDVI Receiver. Turn all the devices ON.
2
Power Supply
(PWR-000022-R)
L2
1
STEP 1: Connect your VelocityDVI-3 Receiver to the VX320 using multi-mode fiber-optic cables (up to
1000 meters). Connect L1 to any Transmit Port of the Upper Card Cage and L2 to the same numbered
Receive Port of the Lower Card Cage. (See the Digital Crosspoint Switch detail diagram, left.)
L1
Copyright © 2010. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
L2
L1
VEL-3 Single Link DVI Receiver
Data
▲
Video/Data
▼
Velocity
Dual Output
dvi
Velocity
dvi
Digital Video Extension System - 3
Receiver
Powered by
MRTS Technology
DV Ito Display
DVI to Display DDC
DVI to Display
(SECONDARY)
DVI to Display
DDC (PRIMARY)
VX320_VEL-4_VEL-3_Quick_Start_Rev_A
PHONE: 1-800-291-3211
WEBSITE: www.thinklogical.com
EMAIL: support@thinklogical.com
Visit us online at www.thinklogical.com for more product information, current updates and the complete line of Thinklogical products.
TM
Loading...