Page 1
Wing Span
39.5 in/ 1000 mm
Wing Area
Flying Weight
Fuselage Length
22 oz/ 620 g
259 sq in/ 16.7 sq dm
31.5 in/ 805 mm
Specifications
INSTRUCTION MANUAL
Warning! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric powered precision model. Operating this model without prior preparation ma y cause
injuries. Remember, sa fety is the most important thing. Always keep th is instruction manual at
hand for quic k reference.
*Specifications are subject to change without notice.*
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY(ARF) SERIES
MADE IN CHINA
The World Models
Manufacturing Co., LTD.
www.theworldmodels.com
Requires: 4-channel radio w/ 4 micro servos,
Outrunner Motor KM0283800
20A brushless ESC, 3 cells 11.1V
2100 mAh Li - Po battery & charger.
(E196B)
E196BP O11180902
Page 2
P.1
Apply thread locker
Apply epoxy glue.
Pierce the shaded portion
covering film.
Appl
(C.A.glue, super glue.)
y instant glue
Ensur
movement while assembling.
e smooth non-binding
Do not overlook this symbol !
P. 3 -9
Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT
and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you
find to be defective after the gluing process may be difficult to remove for warranty replacement. The
manufacturer will replace any defective parts, but will
not
extend to the parts that are good before
gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.
IN DE X
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P. 1
P. 2
P.9
BEFORE YOU BEGIN
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual comprise of the following : -
1
2
3
Assembl
sides the same way.
e left and right
Pee
covering film.
l off shaded portion
Drill holes with the specified
diameter (here:3mm).
Pay close attention here!
Cut off shaded portion.
Must be purchased separately !
Warning!
3mm
E196BP O11180902
Page 3
P.2
Parts List
COVERING:- LIGHTEX SGX 196000 COVERING-RAMBLER EP
LIGHTEX SGX 100 WHITE
1. MAIN WING -- 1 pc.
2. PUSHROD Ø1.4x58mm w/ Threads (For Aileron) -- 2 pcs
FUEL TUBE Ø4x4mm -- 4 pcs
STRAPER -- 2 pcs
CLEVIS -- 2 pcs
HORN -- 2 pcs
SCREW PM2x16mm -- 4 pcs
3. FUSELAGE -- 1 pc.
STABILIZER & ELEVATOR -- 1 set
4. VERTICAL FIN & RUDDER -- 1 set
5. TAIL LANDING GEAR -- 1 set
6. PUSHROD Ø1.4x425mm w/ Threads (For Rudder) -- 1 pc.
CLEVIS -- 1 pc.
FUEL TUBE Ø4x4mm -- 1 pc.
HORN -- 1 set
SCREW PM2x8mm -- 2 pcs
7. PUSHROD Ø1.4x405mm w/ Threads (For Elevator) -- 1 pc.
CLEVIS -- 2 pcs
FUEL TUBE Ø4x4mm -- 1 pc.
HORN -- 1 pc.
SCREW PM2x8mm -- 2 pcs
8. SOCKET HEAD SCREW M3x8mm -- 2 pcs
SCREW PM2x12mm -- 4 pcs
SCREW PWA2x8mm -- 4 pcs
WASHER d3xD7mm -- 2 pcs
WASHER d2xD5mm -- 2 pcs
M3 NUT -- 2 pcs
400 GEAR BOX -- 1 set
COWLING -- 1 pc.
SPINNER Ø36mm SP26036FR0 -- 1 pc.
FOLDING PROPELLER SET PL6314020 -- 1 set
OUTRUNNER MOTOR KM0283800 -- 1 pc.
9. STRAPER -- 2 pcs
FUEL TUBE Ø4x4mm -- 2 pcs
SPONGE 10x50x150mm -- 1 pc.
BATTERY TIE 200mm -- 1 pc.
DOUBLE-SIDED TAPE 30x35mm -- 1 pc.
10. PLYWOOD 2x20x64mm (Wing Protection) -- 1 pc.
SCREW PM2.5x16mm -- 2 pcs
WASHER d2.5xD8mm -- 2 pcs
11. MAIN LANDING GEAR -- 1 set
LANDING WIRE STRAPS PL411030 -- 2 pcs
SCREW PA2.3x12mm -- 4 pcs
MAIN WHEEL Ø40mm -- 2 pcs
COLLAR Ø2.6mm w/ set screw -- 2 sets
12. CANOPY -- 1 pc.
SCREW PWA2x8mm -- 4 pcs
E196BP O11180902
Page 4
P.3
Aileron Servos
2
4
PM2x16 mm Screw
Ø1mm pilot holes for World
Models tri-horn are pre-drilled.
Please look for pin-hole marks
at under side of control surfaces.
Bottom View
2mm
Main Wing
1
App l y i n st a n t t ype CA gl u e t o b o t h s ide s of ea c h h i n ge .
Bottom View
Ailer on Se rvo Lead
PM2x16 mm
Pushro d
Ø1.4x58 mm
Clevis
2mm
Horn
Fuel Tube
Ø4x4mm
strape r
1mm
1mm
E196BP O11180902
Page 5
Stabilizer & Elevator
3
App l y i n st a n t t ype CA gl u e t o b o t h s ide s of ea c h h i n ge .
Vertical Fin & Rudder
4
App l y i n st a n t t ype CA gl u e t o b o t h
sid e s o f ea c h h i ng e .
Comple ted
P.4
A=A
A
A
B=B'
B
B
Comple ted
Tem p o r a ry i n stal l the m a in w i n g, a d just
leve l i n g o f the s t abi l i z er t o ma k e it a s
para l l e l t o the m a in w i ng a s po s s i b le.
(Sta bi li ze r)
(Mai n Wi ng )
B B'
B=B'
Rem ove cov ering s for all s urfac es in
con tact be fore ap plyin g A/ B epoxy g lue.
E196BP O11180902
Page 6
Tail Landing Gear
5
Rudder Pushrod
6
2
PM2 x 8mm Screw
1mm pilot holes for World Models tri-horn are pre-drilled. Please look
for pin-hole marks at under side of control surfaces.
Bott om Vie w
PM2 x 8mm
Clevi s
Fuel Tu be
Ø4x4mm
2mm
Ø1.4x 42 5m m
Bottom View
Elevator Pushrod
7
PM2 x 8mm Screw
1mm pilot holes for World Models tri-horn are pre-drilled. Please
look for pin-hole marks at under side of control surfaces.
2
Bott om View
Horn
Fuel Tube
Ø4x4mm
Clevi s
PM 2x8mm
2mm
Ø1.4x 405 mm
Push rod
P.5
Wood en Bl ock
Wire Ø1x 85m m
85mm
18mm
98mm
26mm
E196BP O11180902
Page 7
P.6
8
Outrunner Motor & Cowling
5
Don't over-tighten the PM2 screws, let the
propeller blades align themselves when spinning.
PM2 x 12 mm
PM2 x 12 mm
PA2. 6 x 8mm
Spin ner
Ø36m m
PWA 2 x 8m m
1.5mm
7
PWA2x8mm Screw
4
2
PM2x12mm Screw
4
d3xD7mm Washer
2
M3x8mm Socket Head Screw
TWM
KP0011310
SolderSolder
Don' t ove r-tig hte n the
PM2 sc rew s, too mu ch
stre ss on t he scre ws
coul d spl it the fi rew all.
1
3
2
6
4
PM2 x12mm
d2x D5mm Was her
M2 Nu t
M3x8 mm
d3xD 7mm Wa she r
M3 Nut
2
d2xD5mm Washer
2
Pap er
M3x3 mm
Set S cr ew
Stee l W ir e
Ø1.2 x3 5m m
E196BP O11180902
TO ALLOW FOR BACKLASH
OF MATCHING GEAR, PUT
A PIECE OF THIN PAPER
BETWEEN THE GEARS AND
THEN TIGHTEN THE M3X8mm
SCREWS. REMOVE THE
PAPER BEFORE FLYING.
Page 8
P.7
Main Wing
10
Main Landing gear
11
PM2.5x 1 6mm Screw
2
d2.5 x D8m m Washer
2
Wing Protection 2x20x64 mm
PM2.5x16mm
d2.5 x D8mm
Washer
2.5mm
3mm Set Screw
2.6mm Collar
PA2.3x12mm Screw
4
2.6mm Collar
2
Radio Equipment
9
Double-Sided Tape
Battery Tie
Motor
Battery
Elevator Pushrod
Rudder Pushrod
Straper
Rudder Servo
Elevator Servo
Sponge
Fuel Tube Ø4x4mm
PA2.3x1 2mm
Land ing
wire s tra ps
1.5mm
56.2 mm
48mm
2.5mm
Brush les s ESC
E196BP O11180902
Page 9
P.8
Canopy
12
A = A ' B = B '
C =C '
B
B '
C
C '
A
A '
Wing Setting
13
PWA2 x 8mm Screw
4
PWA2 x 8mm
1mm
Pilot
Adjust the wing and fuselage configuration as shown in the diagrams.
E196BP O11180902
Page 10
P.9
Adjust the c ontrol th rows as sho wn in the
diagram. These throws are good for genera l
flying. You can adjust acco rding to your
personal preference.
Elevator
Control Throws
Rudder
20mm
20mm
10mm
14
Aileron
8mm
C.G.
15
The ideal C. G. position is 58mm (2 .28 in.) behind
the leadin g edge meas ured at whe re the wing
meets the fuselage. In order to obtain the C.G.
specified, add weig ht to the fus elage or move
the battery position. Check the C.G. before
flying.
58mm
C.G.
2.28in.
8mm
10mm
Warning!
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.
# is specially designed to be powered by KM0283800 Outrunner Motor.
# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running
propeller. Extreme caution should be exercised when working with electric powered models. Make sure the
propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure
you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental
movement of the throttle stick will spin the propeller and could cause injuries.
# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles.
Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone.
Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the
glue and shrink the covering at the same time, causing the seams to pull away.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
http :// ww w.th ewo rldmo del s.com /pa ra/in str uctio n/i nstru cti onMan ual s.p hp
E196BP O11180902
Page 11
Product Registration Form (US Customers)
We would like to share with you any relevant information regarding your model, including
product news and free upgrade parts when applicable. Please fill in the following and send to
AirBorne Models, 4749-K, Bennett Drive, Livermore, CA 94551 USA.
1. Name:
2. Address:
3. Phone #: E-mail:
4. Model:
Wing QC# Fuselage QC#
(QC numbers are stamped on wing and fuselage)
5. Date of Purchase:
6. Store Name:
Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.
Thank you very much for purchasing our product.
E196BP O11180902
Page 12
The World Models
Manufacturing Co., LTD.
www. t h e w orldm o d e l s.c o m
E196BP O11180902
Loading...