0.60 0 75 cu in displacement 2 stroke- .. . -
Requires: 6-channel radio w/ 7 standard servos
Warning! This model is not a toy.
THE WORLD MODELS
MANUFACTURING CO., LTD.
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY(ARF)SERIES
MADE I N CH INA
www.theworldmodels.com
INSTRUCTION MANUAL
P-51 MUSTANG 60
Wing Span
Wing Area
Flying Weight
Fuselage Length
64.5 in / 1640mm
755 sq in / 48.7 sq dm
8.4 lb / 3700g
56.0 in / 1430mm
Specifications
* Specifications are subject to change without notice.*
E
A
D
R
-
Y
T
-
T
S
O
O
-
F
M
L
L
Y
A
ARF
0.91 cu in displacement 4 stroke.. -
P-51 MUSTANG 60
P. 1
P. 3 - 1 1
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P. 1
P. 2
P. 1 1
BEFORE YOU BEGIN
Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT
and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you
find to be defective after the gluing process may be difficult to remove for warranty replacement. The
manufacturer will replace any defective parts, but will
not
extend to the parts that are good before
gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual comprise of the following : -
1
2
3
Do not overlook this symbol!
Cut off shaded portion.
Peel off shaded portion
covering film.
Pay close attention here!
Pierce the shaded portion
covering film.
Must be purchased separately!
Drill holes with the specified
diameter (here: 3mm).
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Apply epoxy glue.
Apply thread locker
3mm
Parts List
1. MAIN WING -- 1 pair
2. WING TUBE Ø16x595mm -- 1 pc.
3. SCREW PM2x6mm -- 12 pcs
M2 NUT -- 12 pcs
WASHER d2xD5mm -- 24 pcs
MAIN LANDING GEAR COVER -- 1 pair
RETRACTABLE LANDING GEAR COVER -- 1 pair
MAIN WHEEL Ø90mm -- 2 pcs
4. SCREW PM2x20mm -- 6 pcs
SCREW PWA2x8mm -- 8 pcs
TRI-HORN M3x14mm(L)(For Aileron) -- 2 set
PUSHROD Ø1.8x87mm w/ Threads(For Aileron Servos) -- 2 pcs
SERVO MOUNTING PANEL 2mm(For Aileron Servos) -- 1 pair
FUEL TUBE Ø6x5mm -- 4 pcs
STRAPER -- 2 pcs
CLEVIS -- 2 pcs
5. FUEL TUBE Ø6x5m m -- 3 pcs
Y ROD Ø1.8x110mm(For Aileron Servo) -- 1 set
RING Ø2.6m m -- 2 pcs
CLEVIS -- 2 pcs
STRAPER -- 1 pc.
6. STABILIZER & ELEVATOR -- 1 set
FUSELAGE -- 1 pc.
7. VERTICAL FIN & RUDDER -- 1 set
8. TAIL LANDING GEAR -- 1 set
SCREW PA3x12mm -- 2 pcs
COLLAR Ø2.6mm w/ set screw -- 1 set
TAIL WHEEL Ø30mm -- 1 pc.
9. SCREW PM2x20mm -- 6 pcs
TRI-HORN M3x21mm(L)(For Elevator) -- 2 sets
PUSHROD Ø1.8x560mm w/ Threads(For Rudder Servo) --2 pcs
FUEL TUBE Ø6x5mm -- 2 pcs
CLEVIS -- 2 pcs
10. SCREW PM2x25mm -- 3 pcs
TRI-HORN M3x14mm(L)(For Rudder) -- 1 set
PUSH ROD Ø1.8x71 0mm w/ Threads(For Rudder Servo) -- 1 pc.
FUEL TUBE Ø6x5mm -- 1 pc.
CLEVIS -- 1 pc.
12.SOCKET HEAD SCREW M4x25mm -- 4 pcs
WASHER d4xD15mm -- 4 pcs
ENGINE MOUNT PL5111080 -- 1 set
13. FUEL TANK 380cc -- 1 set
BALSA 8x8x118mm(Fo r Fue l Tank Position Fixing) -- 1 pc.
COVERING:- TOUGHLON STL 370 SILVER
TOUGHLON STL 251 SKY BLUE
TOUGHLON STL 201 BLACK
TOUGHLON STL 311 FERRARI RED
P. 2
14. THROTTLE PUSHWIRE Ø1.2X450 mm-- 1 pc.
PLASTIC TUBE d2xD3x180mm -- 1 pc.
ANTI-VIB RATION MOUNT 4C-91--1 set
INCLUDE:SOCKET HEAD SCREW M4x35mm -- 4 pcs
SCREW KM3x20mm -- 8 pcs
WASHER d4xD12mm -- 8 pcs
NLON INSERT LOCK NUT M3 -- 8 pcs
NYLON INSERT LOCK NUT M4 -- 4 pcs
ENGINE MOUNT ALUMINUM PLATE -- 1 set
15. LINKAGE CONNECTOR Ø2.1mm -- 3 sets
16. PLYWOOD 6x41x120mm(For Throttle Servo) -- 1 pc.
BALSA 7x7x41mm(Fo r Throttle Servo Stand) -- 2 pcs
PLYWOOD 6x61x118mm(For Fuselage Servo) -- 1 pc.
BALSA 7x7x61mm(For Fuselage Servo Stand) -- 2 pcs
PUSHROD Ø1.8x100mm(For Elevator) -- 1 pc.
PUSHROD CONNECTOR 4x9x20mm(For Elevator) -- 1 set
SPONGE 60x70x118mm -- 1 pc.
FUEL TUBE Ø6x5mm --2 pcs
STRAPER -- 2 pcs
17. SCREW PM4x40mm -- 2 pcs
WASHER d4xD15mm -- 2 pcs
PLYWOOD 2x20x95mm (Wing Protecticon) -- 1 pc.
AIR SCOOP -- 1 pc.
SCREW PWM2.5x12mm -- 3 pcs
18. SCREW PWA2.3x12mm -- 8 pcs
SILICON GROMMET d1.5xD6.5mm -- 8 pcs
DOUBLE-SIDED TAPE 8x1000 -- 1 pc.
CANOPY -- 1 pc.
PILOT PC13057B2 -- 1 set
19. SCREW PWA2.6x12mm -- 4 pcs
SILICON GROMMET d1.5xD6.5mm -- 4 pcs
SPINNER(blue/ alu.back plate) Ø102mm -- 1 set
COWLING -- 1 pc.
TRANSPARENT 3D TEMPLATE -- 1 pc.
20. DECALS -- 1 set
Wing Tube Ø16x595mm
Main Wing
1
Main Wing
2
Completed
Make sure to glue securely. If not properly glued, a failure in fight may occur.
P.3
Pre-glued
Up
Down
Bottom View
Aileron Serv o
4
2mm
Fue l Tu be
Ø6x 5mm
Clevis
PM2 x 20mm
Tri-horn
M3x14mm(L)
PM 2 x 20mm Screw
6
8
PWA 2 x 8 mm Screw
Strap er
Fue l Tub e
Ø6x 5mm
Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole
marks at under side of control surfaces.
Completed
PWA 2 x 8mm
1mm
Retractable Landing Gear
3
PM 2 x 6 mm Screw
12
24
d2 x D5mm Washer
M2 Nut
12
Completed
P. 4
Washer
d2 xD 5mm
PM 2 x 6mm
M2 Nut
Pushrod Ø1.8x87mm
1.5mm
Bottom View
Bottom
View
P. 5
AA'
A=A'
Stabilizer & Elevator
6
Vertical Fin / Ru dder
C
C'
C=C'
7
Completed
Completed
pre-glued
Bottom View
Flap and Retract Servo
5
Selec t the servo horn tha t will give 26 mm
0
travel wh en rotates through 180 .
Lead to Flap servo
Wheels up position
Wheels down Position
To
L-side
To
R-side
Lead to re tract servo
Lead to Aileron servo
Ring
Clevis
1mm
Flaps up
Flaps Down
Fuel Tube
Ø6x5mm
Straper
Y Rod Ø1.8 x 110mm
pre-glued
(Stabilizer)
(Main Wing)
BB'
B=B'
Temporary install the main wing, adjust
leveling of the stabilizer to make it as
parallel to the main wing as possible.
Fuel Tube
Ø6 x 5mm
Tri-horn
M3 x 21mm(L)
PM 2 x 20m m
Clevis
2mm
Elevator Pushrod
Ø1.8x 560mm
P. 6
PA3x12mm Screw
3mm Set Screw
2.6mm Collar
2
1
1
Tail Landing Gear
8
1.5mm
2.5mm
PA3x12mm
3mm Set Screw
PM 2 x 20 mm Screw
6
Ø1mm pilot holes for World Models tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
Ø1mm pilot holes for World Models tri-horn are pre-drilled.
Please l ook for pin-hol e ma rks at under side o f control surfaces.
PM 2 x 25 mm Screw
3
10
Elevator Pushrod
9
≈
75m
m
PM2 x 25mm
42mm
95mm
210mm
Rudder Pu shrod
≈
Fuel Tube
Ø6 x 5mm
Ring
Clevis
2mm
PM2 x 25 mm
Rudder Pushrod
Ø1.8x 710mm
Tri-horn
M3 x 14mm(L)
UP
12
d4 x D15mm Washer
4
4
Engine Mount
PL5111080
Socket Head Screw
M4 x 25mm
Washer
d4 x D15mm
Blind nuts are off-centered to keep
the spinner at the fuselage axis.
Apply thread locker to screws
Fuel Tank
13
Insta ll B alsa 8 x 8 x1 18 m m
Fuel Tank
380cc
(For Fu el Tank Po sitio n Fi xing)
Elevator Pushrod
Elevator & Rudder Pushrod
11
Rudder Pushrod
Completed
Bottom View
P.7
M4 x 25mm Socket Head Screw
Fuel Tank
380cc
Bottom View
Engine Mount
P.8
M4x35mm
M4 Nylon Insert Lock Nut
4
8
4
8
d4 x D12mm Washer
d4 x D12mm
KM3x20mm Screw
Illustration is for inverted mounting.
You can mount the engine upright
or sideways simply by rotation the
engine mount. Thrust angles will
not be affected.
d2xD3x180mm
Plastic Tube
Throttle Pushwire
8
M4 Nylon Ins er t Lo ck N ut
137mm
5.39in
14
Installed Engine Position
M4 x 35 mm
M3 Nylon Insert Lock Nut
Washer
Socke t He ad Screw
Socket Head Screw
ANTI-VIBRATION MOUNT INSTALLATION
KM3 x 20mm
Make sure the rounded edges
are facing the shock absorbing
silicon PAD.
M3 Nylon Insert Lock Nut
Ø1.2x450mm
3 x 3mm Set Screw
M2 Nut
Linkage Connector
3
3
3
3
2mm Washer
Please refer to attached sheet for linkage connector installation.
Servo Set
15
Throttle Pushwire
3mm
Thrott le Servo.
2mm
2mm
M2 Nut
2mm
Engine
P. 9
Servos
16
Elevator Servo
Plywood
Balsa
7 x 7 x 41mm
6 x 41 x 120mm
Plywood
6 x 61 x 118mm
Balsa
7 x 7 x 61mm
Elevator Servo
Throttle Servo
Rudder Pushrod
Ø1.8x710mm
Throttle Push rod
Ø1.2x450mm
Rudder Servo
Sponge
Fuel Tube
Ø6 x 5mm
KM 2x8mm
M2 Nut
Elevator Pushrod
Ø1.8x100mm
PM4 x 40 mm Screw
PWM2.5 x 12mm Screw
2
2
d4 x D15mm
Washer
Main Wing
17
3
PWM2 .5 x 1 2mm
Washer
d4 x D15 mm
Screw
PM4 x 40 mm
Completed
Wing Protection
2 x 20 x 95mm
Pushrod Connector
Install and arrange the servo as shown in the diagram.
J1(Pushrod Ø1.8x100mm
)
J2(Pushrod Ø1.8x560mm
)
J1
J2
Receiver
Battery
P. 1 0
Cowling
PWA2. 6 x 12 m m Screw
d1.5 x D6.5 mm Silicon Grommet
4
4
19
1.5mm
PWA2. 6 x 12 m m
Silicon Grommet
d1.5xD6.5mm
Spinner Ø102mm
2
18
Canopy
First insert the grommet to the canopy then apply screw.
Apply double-sided tape
Pilot
1
Decals
PWA2.3 x 12 m m Screw
d1.5 x D6.5 mm Silicon Grommet
8
8
PWA2.3 x12 mm
d1.5 x D6.5 mm
Silicon Grommet
1mm
Please refer to the attached sheet for usage of the transparent 3D template.
First insert the grommet to the cowling then apply screw.
P. 1 1
C.G.
The ideal C. G. position is 115mm ( 4.5in ) behind the
leading edge measured at where the wing meets the
fuselage. In order to obtain the C. G. specified, add
weight to the fuselage or move the battery position.
Check the C. G. before flying.
22
Control Throws
25mm
25mm
Elevator
45mm
45mm
Rudder
18mm
18mm
Ailero ns ( away from fuse la ge )
21
40mm
Flaps (n ear fuselage )
Adjust the control throws as shown in
the diagram. These throws are good for
general flying. You can adjust according
to your personal preference.
C.G.
115mm
4.5in
Measure C.G. with the wheels in retracted position.
Adjust the wing and fuselage configuration
as shown in the diagrams.
A
A'
B
B'
C
C'
A=A'
B=B'
C=C'
Wing Setting
20
P. 1 2
Important Safety Precautions
First time flyer should never fly by himself / herself. Assistance from experienced flyer is
absolutely necessary.
Pre - flight adjustment must be done before flying, it is very dangerous to fly a badly
adjusted aircraft.
pre -
Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller.
A1550803
If you find wrinkles on the covering as a result of weather changes, you can use hot iron
to remove the wrinkles. Please begin with lower temperature setti ng and gradual ly rais e
the temperature until the wrinkles are gone. Too hot an iron may damage the covering.
,
Don t use hot iron near the seams or edges, hot iron will melt the glue and shrink
the covering at the same time,causing the seams to pull away.
Check and re-tighten up all factory assembled screws, use thread locker if necessary.
P-51 MUSTANG 60 is specially designed to be powered by 2C 0.61- 0.75 or 4C 0.91
engine, using a more powerful engine does not mean better performance. In fact, over
powered engine may cause severe damage and injuries.
When Flaps are lowered, nose of model will rise. The nose-up varies with the speed at which
the models is flying when you lower the flaps and the extent to which they are lowered. Check
effect of flaps at higher altitude to avoid surprises during landing. You may apply down trim
of the elevator to compensate for the nose-up effect when lowering the flaps. Taking off with
flaps lowered is not recommended, as the increased drag may require a longer runway and
more engine power for the model.
1
3
4
2
Usage of the transparent 3D template
This transparent 3D template
is used for position guidance
of the actual cutting of the
pre-painted cowling.
Simply cut the transparent 3D template to fit your engine and
exhaust pipe, then slide onto the actual cowling and use as
template to mark the openings required for final cutting.
LINKAGE CONNECTOR
HW7111050 & HW7111060
After fastening the round nut, make sure that
the linkage connector can rotate freely.
Drill 2mm hole at servo horn.
Insert linkage connector
into servo horn.
Make sure shoulder of
screw is cleared from
servo horn.
Add washer to reduce
play if necessary.
Shoulder
Tighten up the round nut
against the shoulder. Apply
CA or permanent thread
locker.
Product Registration Form (US Customers)
We would like to share with you any relevant information regarding your model, including
product news and free upgrade parts when applicable. Please fill in the following and send to
AirBorne Models, 2403 Research Drive, Livermore, CA 94550 USA.
1. Name:
2. Address:
3. Phone #: E-mail:
4. Model:
Wing QC# Fuselage QC#
(QC numbers are stamped on wing and fuselage)
5. Date of Purchase:
6. Store Name:
Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.
Thank you very much for purchasing our product.
A1550803
http://www.theworldmodels.com
Warbirds
Scale
Sports
Trainer
Ducted
Fan
Pattern
Funfly
Electric
Glider
Boat
Accessories
Covering
(Lightex / Toughlon)
Loading...