Page 1
PARTS LIST
Your Stainless Steel Top Kitchen Cart should include the following parts. Please inspect box
contents to ensure you have received all components.
If you are missing any parts, need assistance with assembly or have questions, please contact ŽƵƌ
Customer Service.
A B C D
BOTTOM POLE (4)
Threaded Insert (4)
is pre-installed
TOP POLE (4)
End Cap (4) and
Pole Connector (4)
are pre-installed
SHELF (1)
E F G H
STAINLESS STEEL
TOP (1)
HANDLE (1)
SIDEBAR
w/4 HOOKS (1)
I J K
LOCKING
CASTER (2)
CASTER (2)
WRENCH (1)NON-LOCKING
BASKET (1)
SLIP SLEEVE
(32) + (2) extra
Note: The black circular plastic spacers in between Shelves are used only for packaging
purposes. They are NOT needed. Please discard.
1
Page 2
ASSEMBLY INSTRUCTIONS
STEP 1
Screw CASTERS (I & J) into each BOTTOM POLE
(A). Turn clockwise to screw in place.
Use provided WRENCH (K) to tighten
completely. Failure to do as instructed could
result in caster stem breaking.
A
A (4)
I (2)
A
J (2)
K (1)
STEP 2
On BOTTOM POLE (A), place 1 pair of SLIP SLEEVES (H) at
desired height no higher than 3rdindentation from
bottom. Make sure arrow faces up and word “TOP” is
right-side up. Do this for each BOTTOM POLE (A). Make
sure SLIP SLEEVES (H) height is identical for each
BOTTOM POLE (A).
Note that each POLE (A & B) has slight horizontal line
indentations at 1” intervals. Each SLIP SLEEVE (H) has
raised horizontal lines inside designed to lock in place on
POLE (A & B).
K
K
I
J
H (8)
H
H
Slide pair of SLIP SLEEVES (H) until you hear a click to
confirm pair is locked onto BOTTOM POLE (A). Do NOT
place more than one pair on each POLE (A & B) at a time.
Note: There will be a very small gap in-between two
locked SLIP SLEEVES (H)—this is normal.
A
2
Page 3
ASSEMBLY INSTRUCTIONS
STEP 3
Place SHELF (C) on its side and slide each BOTTOM
POLE (A) through each corner cylinder of SHELF (C).
Make sure LOCKING CASTERS (I) are on same side
and make sure corner cylinders are positioned over
SLIP SLEEVES (H).
Slowly stand unit upright.
Note:
Level side of SHELF (C) is TOP side.
Use a rubber mallet, if needed, to secure SHELF (C).
C
C (1)
A
C
STEP 4
Screw TOP POLES (B) into BOTTOM
POLES (A) in clockwise direction.
Note:
Top of each TOP POLE (B) is
indicated by a BLACK END CAP.
Pole Connectors are pre-installed in
bottom of TOP POLES (B).
3
B (4)
B
A
Page 4
ASSEMBLY INSTRUCTIONS
STEP 5
Repeat STEP 2 & 3 to assemble BASKET (D).
Make sure SLIP SLEEVES (H) height is
identical.
Note:
Use a rubber mallet, if needed, to secure
BASKET (D).
STEP 6
D (1)
D
H (8)
Attach one pair of SLIP SLEEVES (H) to poles on
shorter side of Kitchen Cart as shown.
Slide HANDLE (F) onto poles, making sure corner
cylinders are positioned over SLIP SLEEVES (H).
Repeat STEP to attach SIDEBAR (G) onto opposite
side of Kitchen Cart.
Note:
Use a rubber mallet, if needed, to secure HANDLE (F)
and SIDEBAR (G).
F (1)
G (1)
F
H (8)
G
H
4
Page 5
ASSEMBLY INSTRUCTIONS
STEP 7
Repeat Step 2 for STAINLESS STEEL TOP (E) and
place SLIP SLEEVES (H) at highest position on
TOP POLES (B). Slide STAINLESS STEEL TOP (E)
onto SLIP SLEEVES (H).
E (1)
H (8)
E
H
5
Loading...