Page 1
SML640
Fiesta Go
INSTRUCTION MANUAL
www.singingmachine.com
The Singing Machine® is a registered trademark of The Singing Machine Co.,Inc.
Page 2
Warnings
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The Caution marking is located on the bottom panel.
DANGEROUS VOLTAGE: The lightning flash with arrowhead
symbol within an equilateral triangle is intended to alert the
user to the presence of uninsulated dangerous voltage within
the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
ATTENTION: The exclamation point within an equilateral
triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
DRIPPING WARNING: This product shall not be exposed to dripping or
splashing, and no objects filled with liquids, such as vases, shall be placed
on the product.
VENTILATION WARNING: The normal ventilation of the product shall not be
impeded for intended use.
THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1,
SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURED.
Warning: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
CAN ICES-3(B)/NMB-3(B)
in the literature accompanying this product.
FCC WARNING: This equipment may generate or use radio frequency
energy. Changes or modifications to this equipment may cause harmful
interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The rating information is located at the rear of the unit.
Ihis device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject
to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d’Innovation, Sciences et Développement économique Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
(1) L' appareil ne doit pas produire de brouillage;
(2) L' appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d' en compromettre le fonctionnement.
Important Safety Information
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all Instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in
accordance with the Manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. When the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with a cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15. WARNING: To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture. Do not place objects
filled with water, such as a vase, on the apparatus.
16. The AC mains plug is used as the power disconnect device
and it should remain readily accessible and operable during
intended use. In order to completely disconnect the apparatus
from power, the mains plug should be completely removed
from the AC outlet socket.
17. CAUTION: To reduce the risk of fire or explosion, do not expose
batteries to excessive heat such as sunshine, fire or other
heat sources.
— E1 —
Page 3
Included
Please make sure the following items are included.
AC Adapter
Main Unit
Wired Microphone
Manual
— E2 —
Page 4
Location of Controls (Top/Front)
u
v
w
x
y
U
V
W
X
at
ak
al
am
an
ao
ap
aq
ar
1. Disco Ball
2. LIGHTS Button
3. DISCO BALL Button
4. FUNC (FUNCTION) Button
5. Function indicator
6. ON/STANDBY Button
7. ECHO Control
8. LINE IN Jack
9. Battery indicator
10. MASTER VOLUME Control
11. Speaker/Lights
12. (PLAY/PAUSE) Button
13. (BACK SKIP)Button
14. (NEXT SKIP) Button
(BLUETOOTH) Button
15.
16. MIC VOLUME Control
17. MIC 2 Jack
18. MIC 1 Jack
— E3 —
Page 5
Location of Controls (Rear)
u
v
w
x
y
1. Adjustable Handle
2. Mic Holders
3. USB Port (Power Bank only)
v
4. DC IN Jack
5. Wheels
— E4 —
Page 6
Connection
Connecting the Microphone(s)
u
Connecting to AC Power
v
Microphones:
u
Connect a microphone into Mic jack 1
and the other microphone into Mic jack
v
(if desired).
Note: Do not drop or tap the Mic as
damage to the Mic or speakers may occur.
Do not twirl the microphone by cord as it
will cause damage to the encased wiring.
Insert the AC power cord
1
into a conveniently located
AC outlet having 120V,
60Hz.
2
— E5 —
Note:
Make all connections before
connecting to AC power.
Page 7
Rechargeable Battery
This unit comes with a built-in rechargeable battery pack that will allow the unit to be used
without being connected to AC power. The battery indicator (front of the unit) will show
the battery charge left. The rechargeable battery pack must NOT to be replaced by the
user.
To optimize the battery life, we recommend to charge the unit once a month. When the
battery indicator turns red and flashing, recharge the unit by following the steps below:
Insert the AC power cord into
1
a conveniently located AC
outlet having 120V, 60Hz.
Allow the unit to charge for
2
approximately twelve hours
for a full charge. The battery
indicator will light solid red.
When the battery indicator
3
turn to solid green. Disconnect
the AC cord and the fully
charged unit can be used
for approximately five hours
depending on the function
chosen.
Attention: The sound volume will adjust automatically when the battery is not full.
Recycling and Disposal Information:
• Do not dispose of electronic devices or any of their components.
(especially batteries and LCD displays) in your municipal trash collection.
• Consult your local waste management authority or a recycling organization like Earth911.
com to find an electronics recycling facility in your area.
CAUTION: Rechargeable batteries must be recycled or disposed of properly.
— E6 —
Page 8
USB
cable
Connection
Power Bank
Connecting to Line In Jack
To External Unit
AUDIO OUTPUT
/ HEADPHONE JACK
LINE IN
USB port provides up to 5V, 1.0A
1
2
Connect an external device by using an
appropriate cable (3.5mm audio cable not
included) as shown.
Note:
See page E11 to select and use the Line In
function.
of power for charging.
Plug USB cable (not included)
to Power Bank output port and
connect other side with adaptable
connector to external device (e.g.
mobile phone/ tablet/ lighting
etc.).
Cradle
— E7 —
Page 9
Operation
Light Mode
v
u
Carrying Handle
Press the LIGHTS button the unit
1
will synchronize to the music being
played. Press again to turn off the
lights.
This unit also comes with a Disco
2
Ball feature. Press the DISCO BALL
button to turn the lights on and they
will illuminate onto the ceiling.
u
Bluetooth Mode
To extend the Adjustable Handle, simply
press the Handle Release u and extend
the Adjustable Handle as desired.
To slide the Adjustable Handle back, press
the Handle Release again and slide it
downward.
Press the button to easily set the
machine into pairing mode.
u
— E8 —
Page 10
Operation
Using a Bluetooth Device
v
u
3
FIESTA GO
Connect the unit as described
1
2
Note: You can also press the
disconnect any paired devices in order to
pair another device.
3
Note:
• Always refer to the user manual of your
previously. Press the ON/STANDBY
button to turn the unit on, the
function indicator will light and
flashing blue.
The unit automatically searches
for and pairs a previously paired
Bluetooth device (if previously
paired). If no previously paired
devices are present, connect as
shown in the next step.
button to
Turn on your device’s Bluetooth
option in settings to search for a
discoverable device with a Bluetooth
signal. Select “FIESTA GO” from
the device results on the Bluetooth
menu.
Bluetooth device for detailed instructions.
FIESTA GO
The Bluetooth indicator will light solid
4
Notes:
• If your Bluetooth device prompts you for a
4
• On some Bluetooth devices, once pairing is
• If connection is lost after successful
— E9 —
blue, a tone will sound.
passcode during the pairing process, please
enter “0000” to connect.
complete, select your Bluetooth device as
“Use as Audio Device” or similar.
pairing, check to make sure the distance
between speaker and Bluetooth-enabled
device does not exceed 30 ft/10 meters.
Page 11
Operation
Using a Bluetooth Device (Continued)
V
y
U
You can control your Bluetooth
5
6
7
device to start the music playback
OR press the (PLAY/
PAUSE) button to start playback.
Press the (PLAY/PAUSE)
button during playback to pause
the song.
Adjust the volume to a
comfortable level using the
MASTER VOLUME control on
this unit as well as the volume on
your Bluetooth device.
Connect the microphone(s). Slide
the Mic’s ON/OFF switch to the
ON position.
ak
X
Wat
— E10 —
Adjust the MIC VOLUME control
8
9
10
11
as desired, which will affect both
microphones.
SKIP: Advance or go back one
track by pressing the or
button.
ECHO: Adjust the ECHO control
to add an echo effect to your
voice.
Press the ON/STANDBY button
to turn the unit off; the function
indicator will turn off.
Page 12
Operation
Using the LINE IN Jack
Press the ON/STANDBY button
1
to turn the unit on, the function
indicator will light and flashing blue.
u
v
w
Connect the external unit to the
2
Notes:
• It is highly recommended to set the
• Skipping files/tracks is not possible when
3
x
4
LINE IN Jack on the front of this
unit. Connecting an external unit
will allow the audio to be played
through your Singing Machine.
volume on the auxiliary unit to 1/3 or
lower to avoid distortion.
using an external device.
Repeatedly press the FUNC
(FUNCTION) button to select
the LINE IN mode, the function
indicator will turn solid green.
Adjust the volume using the
MASTER VOLUME control on
this unit or your external device’s
volume control.
y
5
— E11 —
Connect microphone(s) and
slide the ON/OFF switch on the
microphone to the ON position.
Page 13
Operation
Using the LINE IN Jack (Continued)
W
V
U
Adjust the MIC VOLUME control
6
7
8
as desired, which will affect both
microphones.
ECHO: Adjust the ECHO control to
add an echo effect to your voice.
Press the ON/STANDBY button
to turn the unit off; the function
indicator will turn off.
Energy Saving (Auto Power System-APS)
The unit will automatically enter the Standby mode after 20 minutes in the following
situations:
1. There is no audio playback on Bluetooth/Line in mode;
2. The playback of external music player had been stopped but the audio cable is still
plugged into the LINE IN jack.
The unit can be resumed to turn on by pressing the ON/STANDBY button once.
APS is for energy saving purposes.
— E12 —
Page 14
Troubleshooting Guide
Should this unit exhibit a problem, check the following before seeking service:
No Power
• Power is not on; press the ON/STANDBY button to turn power on.
• Make sure the unit is connected to AC power.
• Confirm the AC adapter is connected securely to the back of the unit.
• Connect the unit to a different outlet.
• The unit has no battery left. Connect to AC power to recharge the battery.
No Sound – General
• Master Volume is set to minimum; raise volume.
• Correct Function was not selected; select using the FUNC (FUNCTION) button.
No sound from the microphone
• Make sure it is firmly connected to the MIC 1 or MIC 2 jack.
• Make sure the Power switch on the Mic is set to the On position.
• Make sure the MIC VOLUME controls are not on the lowest setting.
• MASTER VOLUME is set to minimum; raise volume.
The Bluetooth device cannot be paired or connected with the unit.
• Ensure any other Bluetooth devices are turned off to avoid accidental pairing.
• You have not activated the Bluetooth function of your device; see page E9 or refer to
the Bluetooth device user’s manual.
• The system is not in pairing mode; press the
button to restart pairing.
The Music is not available on the unit after successfully connecting the Bluetooth.
• Ensure your Bluetooth device can support the A2DP Bluetooth profile.
• The volume on the external Bluetooth device is set to low or muted; raise as desired.
— E13 —
Page 15
Specifications
AUDIO
Output Power (Full range) .......................................................................................... 8 Watts (RMS)
BLUETOOTH
Bluetooth Version ...............................................................................................................................V5.0
Working Distance ..........................................Up to 30 feet/10 meters measured in open space
JACK
Microphone ....................... -74 dB 600 Ohms impedance with 6.3 mm Dynamic Microphone
External Input ...........................................................................................................3.5 mm Line in Jack
GENERAL
Power .......................................................................................................... AC 100-240V ~ 50/60Hz
AC power (power adaptor)
Brand name ........................................... SHENZHEN SHI GUANGKAIYUAN TECHNOLOGY., LTD.
Model .....................................................................................................................GKYPS0150090US1
Output .................................................................................................................................... 9V 1.5A
Battery ..........................................................................................Lithium ion battery 7.4V, 2500mA
Dimensions - Main Unit ................... 13.4 (H) x 10.9 (W) x 10.7 (D) in (340 x 276 x 271mm)
Weight - Main Unit ......................................................................................................8.9 lbs (4.05 kg)
Specifications are subject to change without notice.
The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by
The Singing Machine Company, Inc. is under license. Other
trademarks and trade names are those of their respective
owners.
— E14 —
Page 16
Visit Our Website: www.singingmachine.com
Copyright © 2019 - All Rights Reserved.
The Singing Machine Company, Inc.
4060 E Jurupa Street, Unit B
Ontario, CA 91761-1413 USA
U.S. Representative
Company Name : The Singing Machine Company, Inc.
Address : 6301 NW 5th Way, Suite 2900, Fort Lauderdale,
FL33309, USA
Telephone : 954 -596-1000
Website : www.singingmachine.com
PRINTED IN CHINA
640-xxxx-ENG01-US
Loading...