The Singing Machine iSM1050BT Instruction Manual

The Singing Machine® is a registered trademark or The Singing Machine Co., Inc.

The Singing Machine® es marca registrada de The Singing Machine Co., Inc.

iSM1 050BT

INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES

www.singingmachine.com

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 1

Warnings

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

NSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The Caution marking is located on the bottom panel.

CAUTION

ISK OF ELECTRIC SHOCK

DO NOT OPEN

DANGEROUS VOLTAGE: The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to alert the user to the p

resence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE T

HIS UNIT TO RAIN OR MOISTURE.

Class II equipment symbol. This symbol indicates that the unit has a double insulation system.

ATTENTION: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and m

aintenance (servicing) instructions in the literature accompanying

this product.

DANGER: This symbol is intended to alert the user to the risk of e

xposure to invisible and hazardous laser radiation if the cover or back is opened, the interlock fails or is defeated. Direct exposure to the beam may damage your eyesight.

FCC WARNING: This equipment may generate or use radio frequency e

nergy. Changes or modiﬁcations to this equipment may cause harmful interference unless the modiﬁcations are expressly approved in the instruction manual. The user could lose the authority to operate this e

quipment if an unauthorized change or modiﬁcation is made. T

his device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, i

ncluding interference that may cause undesired operation.

LASER SAFETY: This unit employs a laser. Only qualified service personnel should attempt to service this device due to possible eye injury. CAUTION: USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE PROCEDURE HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

INDUSTRY CANADA NOTICE

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that

may cause undesired operation of the device.

RIPPING WARNING: This product shall not be exposed to dripping or splashing,

and no objects filled with liquids, such as vases, shall be placed on the product. VENTILATION WARNING: The normal ventilation of the product shall not be impeded for intended use. SAFETY VERIFICATION:This device is made and tested to meet safety standards of the FCC, requirements and compliance with safety performance of the U.S. Department of Health and Human Services and also with FDA Radiation Performance Standards 21 CFR Subchapter.

OTE: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful i

nterference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio c

ommunications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by t

urning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

•

The rating information is located at the bottom of the unit.

CAN ICES-3(B)/NMB-3(B)

Important Safety Information

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all Instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the Manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periodsof time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Do not place objects filled with water, such as a vase, on the apparatus.

16. The AC mains plug is used as the power disconnect device and it should remain readily accessible and operable during intended use. In order to completely disconnect the apparatus from power, the mains plug should be completely removed from the AC outlet socket.

17. CAUTION: To reduce the risk of fire or explosion, do not expose batteries to excessive heat such as sunshine, fire or other heat sources.

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 1

Included

Please make sure the following items are included.

Pedestal

Speaker Stand x 2 Speaker Base x 2

Screws

Power Cord Clamps x 2

iSM1050BT Base

Manual

Bonus CD

Detachable Mic

Holder x 2

Stand

Audio/Video Cable

Wired Microphone x 2

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 2

Installation

1. Insert the Pedestal into the Stand

u and then gently rotate clockwise v until tight, making sure the

screw hole in the Pedestal aligns with the screw hole in the Stand.

2. Insert and tighten the self-tapping screw (silver) into the bottom of the Pedestal.

3. Insert the Power Cord Clips into areas u and v and secure using the two clamp screws (silver).

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 3

Installation

4. Insert the Base into the Pedestal u and then gently rotate clockwise v until the screw hole in the Base aligns with the screw hole in the Pedestal.

5. Insert and tighten the self-tapping screw (silver) into the top of the Pedestal.

6. Insert the speaker body into the Speaker Stand making sure to align the screw holes, then insert two screws (black) through the bottom of the base into the bottom of the speaker body to secure. Repeat for other speaker.

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 4

Installation

7. Insert the detachable mic holders u into the base mic holder slots.

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 5

Location of Controls (Top/Front)

1. FUNCTION Button

2. Navigation Up 5/Down 6 Buttons

3. MONITOR ON/OFF Button

4. RECORD Button

5. MASTER VOLUME Control

6. CD Compartment

7. CD Lift Open Area

8. Cradle

9. USB Port

10. Headphone Jack

11. Mic 1 Jack

12. Mic 1 Holder

13. Power On/Standby Button/ Indicator

14. MENU Button

15. Bluetooth Pairing Button/Indicator

16. TFT LCD Color Screen

17. Skip/Search Back 7 /Forward 8 Buttons (for CD)

18. ECHO Button

19. EQ (Equalizer) Button

20. Auto Voice Control (AVC) ON/OFF Button

21. BALANCE Button

22. Play/Pause 4; Button

23. MIC 1 VOLUME Control

24. Stop < Button

25. MIC 2 VOLUME Control

26. Mic 2 Holder

27. Mic 2 Jack

6 7

11 12

1918171613 14 15

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 6

Location of Controls (Back)

1. AC Power Cord

2. AUX IN (Left) Jack

3. Right Speaker Jack

4. Left Speaker Jack

5. VIDEO IN Jack

6. VIDEO OUT Jack

7. AUX OUT (Left) Jack

8. AUX OUT (Right) Jack

9. AUX IN (Right) Jack

CD G TR K 8 / 8 00:16:04

PLAYING TIME

PLAYING TR ACK NUMBER A N D TOTAL TRACK NUMBER

- C D P LAY I N G

ME D IA S O URCE

- M P3+ G FIL E S P L AY I N G

MP3G

- U SB P L AY I N G

USB

- C DG P L AY I N G

CDG

5 6

7 8

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 7

Connection

Audio/Video Cables

Rear of External Unit

Video Out (Yellow)

Audio Out White - Left Red - Right

The video and lyrics will be shown on the built-in screen. If you would prefer to output the video and/or audio through your TV, DVD player, stereo, etc., then perform the following steps:

Connect the Audio/Video cable’s yellow plug to the yellow VIDEO OUT jack on the iSM1050BT and the other end to the external unit’s yellow Video In jack.

Connect the Audio/Video cable’s red and white plugs to the red and white AUDIO OUT jacks on the iSM1050BT and the other ends to the external unit’s red and white Audio In jacks. If left unconnected, the audio will just play through this unit’s speakers.

Notes:

• This unit can be used with or without a TV.

• To see the lyrics on the screen, you must use a CD+G disc or an MP3+G.

• Also refer to the TV’s or external unit’s User Guide.

• If you have a mono TV with only one Audio In jack, you may have to purchase a “Y” adapter (stereo to mono) at your local electronics accessories store.

• Audio/Video cables are included.

• Do not connect to AC power until all connections have been made. See bottom of page 9.

Connecting the Unit to an External TV, Stereo, etc.

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 8

Connection

Audio/Video Cables

Rear of External Unit

Video In (Yellow)

Audio In White - Left Red - Right

VIDEO

OUTPUT

AUDIO

OUTPUT

Connect the Audio/Video cable’s yellow plug to the yellow VIDEO IN jack on the iSM1050BT and the other end to the external unit’s yellow Video Out jack.

Connect the Audio/Video cable’s red and white plugs to the red and white AUDIO IN jacks on the iSM1050BT and the other ends to the external unit’s red and white Audio Out jacks.

Notes:

• Also refer to the TV’s or external unit’s User Guide.

• Audio/Video cables are included.

• Do not connect to AC power until all connections have been made. See below.

Connecting an External TV, Stereo, etc. to this Unit

Insert the AC power cord into a conveniently located AC outlet having 120V AC, 60Hz.

Secure the power cord into the Power clamps previously installed.

Notes:

• Make all connections before

connecting to AC power.

• The AC Power Cord has a polarized

plug that fits into the AC outlet only one way. If the plug does not fit properly, turn it over and try again. Do not force and do not file or cut the wide blade.

Connecting to AC Power

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 9

Connection

Connecting the Microphones and Headphones

Microphones:

Insert a microphone’s plug into the Mic 1 jack u. Insert the other microphone’s plug into the Mic 2 jack v (if desired). Note: Do not drop or tap the mic as damage to the mic or speakers may occur. Do not spin the microphone around for the same reason.

Headphones:

For private listening, use headphones (not included). Insert a headphone’s plug into the Headphone jack w. Disconnect when finished so the included speakers can be used.

Connecting the Tower Speakers

To protect the speakers, make sure the iSM1050BT is off and the MASTER VOLUME and the MIC 1 and 2 VOLUME controls are set to minimum.

Connect the right speaker’s plug to the Right Speaker jack and the left speaker’s plug to the Left Speaker’s jack.

Turn the power on and slowly raise the MASTER VOLUME and the MIC 1 and 2 VOLUME controls to a comfortable level.

Right Speaker

Jack

Left Speaker

Jack

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 10

Operation

Connect the unit as described previously. Press the Power On/ Standby button to turn the unit on; the Power On/Standby indicator will light blue and the LCD Screen will begin to operate.

Lift open the CD door and insert a CD (with standard or MP3+G files) or a CD+G by gently pressing it on the center spindle. Then close the CD door. If using the USB drive with MP3+G files, insert the USB into the USB slot.

FAQs

• What is a CD+G?

A CD+G (CD+Graphics), is the standard format for most karaoke discs that will display the words on the screen.

• What is an MP3+G?

MP3+G is the newest format for karaoke music utilizing the MP3’s small file size. It will display the words on the screen. See page 24 to order and download MP3+G files.

Repeatedly press the FUNCTION button until the LCD Screen displays “DISC” to select the CDG/CD mode or USB to select the USB mode.

Press the MONITOR ON/OFF button to view the information and lyrics (if playing a CD+G or MP3+G file) or press again to turn the LCD Screen off.

Playing a CD (with or without MP3+G files), CD+G or USB Drive

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 11

Operation

Press the Play/Pause 4;button to start playback; if listening to an MP3+G or CD+G file, the image and lyrics will appear on the LCD Screen.

Adjust the volume to a comfortable level using the MASTER VOLUME control.

Notes:

• Never place anything other than a CD in the compartment, as foreign objects can damage the unit.

• If no disc is inserted, “NO DISC” will appear on the LCD screen.

• If no USB drive is inserted, “NO USB” will appear on the LCD screen.

• If connected to a TV or other audio source, adjust the volume of the TV using its own volume control.

Connect microphone(s) as shown on page 10, and press the ON/OFF button on the microphone to power it on.

Adjust the MIC VOLUME 1 or 2 control as desired. Increasing this control will increase the volume of the respective microphone.

Adjust the Echo to add an echo effect to your voice. Press the ECHO button, and then increase/decrease the echo using the Skip Forward 8/Skip Back 7 buttons. The higher the number, the more echo effect.

Playing a CD (with or without MP3+G files), CD+G or USB Drive

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 12

Operation

Adjust the Key to obtain the best key for the singer. During playback, press the MENU button, and then navigate to DIGI KEY CTRL using the Navigation 6/ 5 buttons. Adjust the key using the Skip Forward 8/Skip Back 7 buttons. Press the MENU button again when done.

Press the Auto Voice Control (AVC) button to turn this option On (“AVC ON” will appear in the screen) and the vocals on a multiplex recording are muted as soon as the singer begins singing into the microphone. When the singer stops singing, the vocals are automatically unmuted. IMPORTANT: This feature only works with multiplex media.

Press the BALANCE button, and then adjust the balance level using the Skip Forward 8/Skip Back 7 buttons. On multiplex recordings, use the Skip Back 7 button to reduce or eliminate the lead singer’s voice and use the Skip Forward 8 button to reduce or eliminate the music. IMPORTANT: This feature only works with multiplex media.

Playing a CD (with or without MP3+G files), CD+G or USB Drive

Fx EFFECTS

REPEAT

DIGI KEY CTRL

KEY Menu

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 13

Operation

SKIP: Advance or go back one track

by pressing the Skip Back 7/Skip Forward 8 buttons.

Note: If using a USB drive, during STOP mode you can also select a file using the Navigation 6/ 5 buttons to scroll up/down or the Skip Back 7/Skip Forward 8 buttons to scroll left/right.

SEARCH: During playback, press and

hold either the Skip Back 7 or Skip Forward 8 button to move the player forward or backward within a track to locate a specific musical passage. When you release the button, normal playback will resume (for CD).

REPEAT: During playback, press the

MENU button, and then navigate to REPEAT using the Navigation 6/ 5 buttons. Select the desired Repeat setting [ONE (Repeat One song), ALL (Repeat All tracks/files) or DIR (Repeat Directory - this only appears when using a USB drive)] using the Skip Forward 8/Skip Back 7 buttons. Press the MENU button again when done.

PROGRAM: You can program up to 20

tracks on any disc for playback in any desired order. While in the Stop mode, press the MENU button; PRG P01 : 00 (01 represents the program number and 00 represents the track) will appear in the LCD Screen. Select the first track using the Skip Forward 8/ Skip Back 7 buttons. Press the MENU button again to confirm the entry. Repeat to set up to 20 tracks into memory. When done, press the Play/ Pause 4;button to start playback.

Note: Press the Stop button TWICE to stop and clear the program.

Playing a CD (with or without MP3+G files), CD+G or USB Drive

Fx EFFECTS

1/DIR/ALL

REPEAT

DIGI KEY CTRL

Repeat Menu

aman

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 14

Operation

EQ (Equalizer): Repeatedly press the

EQ button to cycle through the EQ options (Pop, Jazz, Rock, Classic) or to turn the EQ off.

PAUSE: During playback, if you wish

to pause the disc momentarily, press the Play/Pause 4; button; “PAUSE” will appear on the screen. Press again to resume normal playback.

Note: Pausing the unit while playing a CD+G may distort the lyrics on the screen. This will remain until the screen is refreshed.

Press the Stop button to stop playback.

Press the Power On/Standby button

to turn the unit off; the On/Power indicator will light red and the LCD Screen will turn off.

Note: You can record your singing as well as the song/video onto a USB drive. See page 22 for more details.

Playing a CD (with or without MP3+G files), CD+G or USB Drive

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 15

Operation

Connect the unit as described previously. Press the Power On/Standby button to turn the unit on; the Power On/Standby indicator will light blue and the LCD Screen will start up.

Repeatedly press the FUNCTION button until the LCD Screen displays “BLUETOOTH” to select the Bluetooth mode; you will hear the Bluetooth sound and the Bluetooth Status indicator will blink.

Press the MONITOR ON/OFF button to turn the LCD Screen off.

Switch ON the Bluetooth function of your bluetooth compatible device within 10 meters (30 ft) from the pedestal unit. You will see “

Singing Machine

”

appear on your device’s search list.

Note:

Please always refer to the user manual of

your bluetooth device for detailed instructions.

Select “

Singing Machine

” to start pairing. Wait for completion of the pairing until you hear a beep from the unit. The Bluetooth status indicator will display a solid blue color.

Notes:

• If your Bluetooth device prompts you for a passcode during the pairing process, please enter “0000” to connect.

• If you have paired before, a list of previously searched results will be displayed. Select “Singing Machine” and confirm.

• On some Bluetooth devices (i.e., computers), once pairing is complete, you must select your Bluetooth device as “Use as Audio Device” or similar.

Using a Bluetooth Device

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 16

Operation

PLAY/PAUSE: Press the Play/Pause 4; button to start playback.

Adjust the volume to a comfortable level using the MASTER VOLUME control.

Note: If connected to a TV or other audio source, adjust the volume of the TV using its own volume control.

Connect microphone(s) as shown on page 10, and press the ON/OFF button to power it on.

Adjust the MIC VOLUME 1 or 2 control as desired. Increasing this control will increase the volume of the respective microphone.

Using a Bluetooth Device

iSM1050-ENG-SPA v2_Layout 1 7/1/13 10:51 AM Page 17

+ 40 hidden pages

The Singing Machine iSM1050BT Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual