ThermoWorks PHARMALARM 1 User Manual

Setup and Installation
1. Open the battery cover and remove the black tab res ting on the battery. Replace the battery cover.
2. Connect the external temperature probe.
3. Select the d esired tempera ture unit (°F or °C) using the but ton on the back.
4. Fully extend the probe wire.
5. Chose a locat ion to mount t he thermometer. Attach the t hermometer using the magne ts on the back or the flip out desk sta nd.
6. Position the sensor in the desired location.
7. Peel the clear protective sheet from th e LCD display.
INT/EX T
1. Press IN T/EXT to display the ambient (INT) or probe temper ature (EXT ).
2. INT will display on t he LCD sh owing the unit is measuring the ambie nt tempera ture using the interna l sensor. EXT will display showing the probe sensor temperature.
Maximum/Minimum
1. Press IN T/EXT to select which M AX/MIN reading to be displayed.
1. Press MAX /MIN once to display the maximum reading.
2. Press MAX/ MIN again to display t he minimum reading.
3. Press MAX/ MIN again to retur n to nor mal.
4. Press and hold MA X/MIN for one second to reset t he MAX/MIN memor y.
5. Always rese t the memori es before taking new ma ximum and minimum r eadings.
High/Low Temperature Alarm Setting (probe sensor only)
1. Press and hold A LARM SET until t he display flashes. HIGH will show on the display.
2. Press the °C/°F b utton on the back to set the desired high valu e.
3. Press ALA RM SET again. LOW wil l show on the display.
4.
Press the °C/°F butt on on the back to set the desired low value.
5. Press ALA RM SET to return to norma l display.
Pressing and h olding the
°C/°F button advances the values automatically.
If the curren t temperat ure is outside the se t limi t, the a larm w ill sou nd unt il the alarm is
silenced or the current r eading returns to within the set limits.
Press a ny but ton to silen ce the a larm .
Alarm ON/OFF
Press ALARM SET to switch the alarm on or of f. AL will be displayed in lower l eft corner
of display whe n alar m is on.
Low Battery Indication
If the batt ery power becomes low will appea r on the display. Replace the battery
with CR2032 3V type.
Display Backlight
1. Press the LIGHT but ton to turn o n the backlight display.
Specifications
Measurement Range Internal Sensor 14 to 122˚F (-10 to 50˚C) Measurement Range External Sensor -58 to 158˚F (-50 to 70˚C)
Display Accuracy ±1°F℉(±0.5°C) between -4 to 122°F (-20 to 50ºC), otherwise ±1.8°F (±1ºC) Display Resolution 0.1˚ Alarm High and low alarms settable in 1.8°F (1.0°C) increments Display Size 0.8 H x 1.9 W inches (21 H x 48 W mm) Battery 3 volt, CR2032 or equivalent x 1 piece (included)
Battery Life 10,000 hours Display Reading Update 10 seconds Probe Cord Length 9.8 feet (3 m)
Product Size 2 H x 2.9 W x 0.7 D inches (52 H x 73 W x 18 D mm) Included Accessories 1) 3 volt, CR2032 battery x 1 piece
2) 1 sensor vial filled with glass beads
3) NIST-Traceable Calibration Certificate (3-points)
PharmAlarm™ 1
Made in China
PharmAlarm™ 1
P-12-010-01-ab
NIST-Traceable Digital Fridge/Freezer Alarm Thermometer
Follow us on:
Utah, U.S.A.
Ph: 801-756-7705
Fax: 801-756-8948
www.thermoworks.com
Loading...