ThermoWorks HAXO-8 User Manual
HUMIDITY & TEMPERATURE
RECORDER
W
HAT HARDWARE DO YOU NEED?
W
HAT HARDWARE DO YOU NEED?
?
LogTag Haxo-8 Humidity and Temperature
recorder.
LogTag LTI/USB Interface Cradle.
?
PC running Windows 2000 or later version.
?
HAT ABOUT SOFTWARE?
HAT ABOUT SOFTWARE?
W
W
LogTag Analyzer software is available for download
from LogTag Recorders website.
Goto
?
www.logtagrecorders.com/software/software.htm
after registering; you will be e-mailed a link, from
where you can download the software.
After installation is complete, a new icon will
?
appear on your desktop.
I
I
NSTALLING THE INTERFACE CRADLE
NSTALLING THE
Plug the Interface Cradle into
?
a USB port.
USB drivers will install
?
automatically. Your operating
system will inform you when
installation is complete.
INTERFACE CRADLE
HAXO-8 Q S GUICK ETUP UIDEHAXO-8 QS GUICK ETUP UIDE
CONFIGURATION OPTIONS
CONFIGURATION OPTIONS
?
User ID - user can enter details about each Recorder.
Push button start Date/Time start
Select ‘ ’ or ‘ ’ depending on
?
requirements.
Enter the start Date and Time if selected.
?
Enable pre-start logging’
Tick ‘ . This function endures
?
readings are taken in case the user forgets to press the Start button.
Select recording mode - Continuously (overwrites old readings when memory is full) or
?
Reading for a specific time (note that changing the recording interval automatically recalculates the recording duration).
Enter a start delay if required (allows the Recorder to stabilise before recording starts).
?
?
?
?
?
?
?
NOTE: It is recommended that all HAXO units be either hung or mounted vertically to minimise the
possibility of water pooling over the sensor (especially in high humidity environments).
Enable the OK (Green) indicator
Tick the ‘ ’ (this shows that the Recorder is recording).
Click on Humidity tab and Select/Enter Humidity Alert parameters.
If you wish to control future configuration of this Recorder, tick the password box and enter a
password. NOTE: Passwords are case sensitive.
Click ‘ ’ and the Recorder will be configured.
Next
When configuration is complete remove the Recorder from the Interface Cradle.
If you wish to configure more Recorders with the same configuration profile, insert the next
Recorder into the Interface Cradle and click ‘ ’. Repeat until all Recorders are configured.
?
Click on Temperature tab and Select/Enter
Temperature Alert parameters.
Again
CONFIGURING THE HAXO-8
CONFIGURING THE HAXO-8
The HAXO-8 must be configured before you can take readings.
?
Start the LogTag Analyzer software.
?
Insert the HAXO-8 into the Interface
Cradle with the blue label to the front.
You will here a click as the contacts
engage.
?
The screen will show ‘
been detected..... Please wait.....
?
If a Recorder has been used previously,
a chart will appear.
?
Select ‘ ’ - ‘ ’ to bring up the
LogTag Wizard
configuration wizard. The ‘
and general instructions
displayed.
?
Click on ‘ ’; LogTag Analyzer will
Next
scan for a Recorder, once found the
configuration options will be
displayed.
A new LogTag has
’.
Welcome
’ will be
D
OWNLOADING DATA
D
OWNLOADING DATA
?
Start LogTag Analyzer software.
Insert the HAXO-8 into the Interface Cradle.
?
The screen will show ‘
?
detected..... Please wait.....
After a few seconds, a Chart will appear (see image).
?
Data can be displayed in Chart, Table or Summary
?
formats by clicking the tabs at the bottom of the chart
dialog.
Data can also be saved in a number of formats including
?
TXT, PDF, HTML and CSV for import into a
spreadsheet program.
G
G
ETTING HELP
ETTING
If after studying the “HAXO Quick setup guide” you still need
further information, please visit the Support section of the
LogTag Recorders website:
www.logtagrecorders.com/support/support.htm
HELP
A new LogTag has been
‘.
Loading...