ThermoWorks 293-933 User Manual

Stainless Steel

ThermaData™ Logger

Quick Start Guide

QUICK START GUIDE FOR THERMADATA LOGGERS

• Remove any old versions of ThermaData Logger software prior to
installing new version, this version should be 3.4.16 or later.
(Your existing data files will not be removed or lost.)

• Install the software by following the on-screen instructions BEFORE
plugging into your PC (see below for more information).

• Open the ThermaData program using the desktop icon.

PC SOFTWARE INSTALLATION

• Place the disk in the CD drive. The disk will autorun. (If it does not,
click 'Start', 'Run...' and browse to the CD drive and click 'Setup.exe' or
double click the 'My Computer' icon on the Desktop and double click
the CD drive.

• ThermaData Logger PC Software requires Microsoft .Net Framework
to be installed on the PC. Some PC's will already have this installed
but if not it will be installed from the disk. Click the 'Accept' button in
the 'Microsoft License window'. (This may take a few minutes to
install). When installed, the ThermaData Logger software installation
will resume.

• When the 'ThermaData Logger Software Setup Wizard' box appears
click the install button.

• The program files will be installed by default to...
"C:\Program Files\Thermoworks\ThermaData Logger\"
(Recommended).

• The 'options' button can be used to install to an alternate location
(Advanced Users).

• A moving bar will show the installation progress.

• Click the 'Close' button to exit the installation procedure.

• Icons for the ThermaData Logger and Utilities software will be placed
on the desktop. ThermaData Logger, Utilities and Help shortcuts will
also be placed in 'Start menu' - 'Programs' - 'Thermoworks' -
'ThermaData Logger'.

SETTING UP THE LOGGER

• Unscrew the USB end cap and connect the logger to the PC’s USB
port directly or use the USB extender supplied.

• Select 'Logger Settings' from the drop-down 'Logger' menu.

• Enter a name for the logger in the Title (User ID) box.

• Select Com Port.

• Select temperature settings for 'over' or 'under' alarm using the drop-
down menu boxes.

• Select the data storage method – 'Stop when full' or 'Overwrite oldest
data'.

• Select a 'Start Delay' (note: for immediate star t enter 0 hours, 0
minutes).

• Select the logging interval (note: the total time the log will last is
shown below the drop-down box).

• Click the 'Send Settings' button.

• Start the logger by clicking the 'Star t button' on the PC screen.

• Re fit the USB end cap ensuring that the O Ring is not damaged,
twisted or trapped to ensure that the unit remains watertight.

READING THE LOGGER

• Be aware if you are using this data logger at high temperature, allow
the unit to cool before handling or connecting to the PC.

• Unscrew the USB end cap and connect the logger to the PC’s USB
port directly or use the USB extender supplied.

• Select 'Get Data' from the drop-down 'Logger' menu.

• 'View' readings using data window or graph window.

• Once you have downloaded the data re-fit the USB end cap ensuring
that the O Ring is not damaged, twisted or trapped to ensure that
the unit remains watertight.

(Full operating instructions for ThermaData Loggers are found in the
‘Help’ tab within the software.)

PLEASE NOTE: This logger is fitted with a SL-561 2/3 AA 3.6V Tadiran
battery (high operating temperature). Failure to use the same type of
battery could cause failure or damage to the logger. The life span of this
battery is up to 8 years. If the battery needs to be changed, unscrew the
sensor end cap using an appropriate sized wrench. On removal please
note that your hands may contain static electricity. Therefore handling of
the circuit board should be kept to an absolute minimum while changing
the battery. Contact ThermoWorks' Technical Support for more details,
[e-mail].

293-900

Sensor Cap

293-930

1762 W. 20 S. #100, Lindon, UT 84042

P-13-012-02-a Ref: 547-297 / 18.04.13

Ph: 801-756-7705 Fax: [phone]

www.thermoworks.com

USB Cap