ThermoWorks 222-213 User Manual

SPECIFICATIONS

Range: -94.00 to 392.00°F (-69.99 to 199.99°C)
Resolution: 0.01° or 0.1° - user selectable
Accuracy: ±0.04°C (-29.99 to 149.99°C) otherwise ±0.2°C /

±0.07°F (-22 to 302°F) otherwise ±0.36°F

Sensor Type: 1/3 DIN Thin Film PT100 to BS EN 60751 (4 wire)
Probe: 4.25 L x 0.125 inches dia. (108 L x 3.3mm dia.)
Battery: 2 x 3 volt CR2032 lithium coin cell
Battery Life: 1000 hours
Display: 0.83 H x 1.89 W inches (21 H x 48 W mm) LCD
Dimensions: 6.1 H x 1.85 W x 0.75 D inches

(153 H x 47 W x 19 D mm)
Weight: 0.22lb. (100g)

This Thermapen has been checked or calibrated against reference
instrument(s) calibrated by an UKAS accredited calibration laboratory.
Traceable to NIST.

Made in the UK

1762 W. 20 S. #100, Lindon, UT 84042

P-12-001-02-a Ref: 547-145 29.05.12

Ph: 801-756-7705 Fax: [phone]

www.thermoworks.com

Reference Thermapen

Operating Instructions

™

INSTRUMENT OPERATION - The

instrument is switched on by unfolding
the probe until the display shows the
temperature. The unit is turned off by
folding the probe back into the side of the
instrument. The probe should not be rotated
more than 180 degrees as damage will
occur. It is recommended to store the probe,
in the closed position, when not in use.

Apply the probe to the substance to be
measured. For optimum accuracy immerse at least 2.75” (70mm) of
the probe in the substance. DO NOT immerse any of the case parts in
liquid. The probe should be allowed adequate time to stabilize to the
temperature of the item to be measured.

INSTRUMENT
CONFIGURATION - This

instrument has four user
selectable slide switches
(switch bank), adjustable
with a paperclip, and a
single push button ‘Trim

ON

1 2 3 4

+

CR2032

3V

Switch bank
Trim adjust
CR2032 battery

Switch

(factory default shown)

ON

1 2 3 4

Adjust’ which is located
under the battery cover.

Switch 1 - Display
Units - Changes display units between °F (factory default) and °C. To

change to °C push the switch toward the batteries.
Switch 2 - Resolution - To change the resolution from 0.01°F
(factory default) to 0.1°F push the switch away from the batteries.
Switch 3 - Auto-off - To disable the auto-off (factory default – 10
minutes) push the switch away from the batteries.
Switch 4 - Reading Trim - For normal use, we do not recommend
using the ‘Trim Adjust’. For further details visit www.thermoworks.com.

INSTRUMENT CLEANING - Clean the instrument regularly with an
anti-bacterial probe wipe to avoid potential bacterial growth.

BATTERY REPLACEMENT A battery symbol
indicates that the batteries will need replacing. The
instrument continues to measure accurately but
we recommend that the batteries be changed as
soon as possible. To replace the batteries, remove

ON

1 2 3 4

+

CR2032

3V

the battery cover using a coin (U.S. quarter works
best). Remove the batteries by pulling the battery retaining clip back
while holding the unit upside down. Replace both batteries, positive
side up, replace cover.

ERROR MESSAGES - ‘Err’ will be displayed if the probe develops a
fault. If the error message remains, contact our service department for
further assistance.

EMC/RFI - Instrument performance may be affected if operated
within a high frequency radio field, such as near a mobile phone, or if
subjected to an electrostatic shock.

GUARANTEE - This instrument carries a one-year warranty
against defects in either components or workmanship. During this
period, products that prove to be defective will, at the discretion of
ThermoWorks, be either repaired or replaced without charge. This
warranty does not apply to probes, where a six-month period is offered.
The product warranty does not cover damage caused by fair wear and
tear, abnormal storage conditions, incorrect use, accidental misuse,
abuse, neglect, misapplication or modification. Full details of liability
are available within ThermoWorks’ Terms & Conditions of Sale at www.
thermoworks.com. In line with our policy of continuous development, we
reserve the right to amend our product specification without prior notice.