Upgrade a standard bathroom mirror by installing a ThermoSphere mirror heaters. A heated mirror gives you
the convenience of steam free mirrors after a hot bath or shower. The simple one cable connection and full self
adhesive backing make ThermoSphere mirror heaters fast and easy to install. A cost effective luxury upgrade for
any mirror.
2
A heated mirror ensures steam free mirrors after a bath
or shower
Simple installation
Simply x to the back of mirror with the self adhesive backing and connect
the lighting circuit or our dual control.
HEATING | WALL | MIRROR
1MM
Safe in bathrooms
The heater pad is concealed behind the mirror, and all electrical connections
are within the wall or ceiling cavity.
Low prole
Only 1mm thick with a low prole, 5mm cable connection. Simply cut a
rebate into the plasterboard. No back box required.
Energy efcient
The low voltage output uses minimal energy to keep your mirrors steam free.
3
4
HEATING | WALL | MIRROR
ThermoSphere Electric mirror heaters
Stock CodeDescriptionShapeOutput (W) Size (MM)
MH-0600
MH-0800Mirror HeaterRectangular 96 600 x 800
MH-0900Mirror HeaterRectangular 108 600 x 900
MH-1000Mirror HeaterRectangular 150 750 x 1000
MH-1200Mirror HeaterRectangular 204 850 x 1200
MH-1300Mirror HeaterRectangular 260 1000 x 1300
MHO-0600Mirror HeaterOval 45 400 x 600
MHO-0800Mirror HeaterOval 76 600 x 800
MHR-0380Mirror HeaterRound 20 380 ø
MHR-0520Mirror HeaterRound 41 520 ø
Mirror Heater
Rectangular 57
400 x 600
Installation accessories
Stock CodeDescriptionSize
MH-DSTDouble Sided Tape25mm x 50m
MH-ADHMirror Adhesive310ml
PIR-01PIR Movement Sensor
5
HEATING | WALL |MIRROR
1
5
2
4
3
1
Mains supply
Mirror heater
2
Mirror
3
Power cable
5
Wall
Mirror
4
Adhere heater to back of the mirrorWire up and x to the wall
Use the self adhesive backing to x the mirror heater to the back
of the ThermoSphere mirror adhesive should be applied around
the perimeter of the mirror.
Lay your mirror onto a clean towel to ensure no scratches or
blemishes are formed when applying the heated element.
PRO TIP
The heated mirror can be installed on walls made of wood,
ceramic tiles, marble, etc. Walls must be dry, stable, smooth and
preferably insulated.
Wire the mirror heater into a marshalling box behind the mirror.
Then line the mirror up ensuring a 5mm gap is maintained around
the perimeter of the mirror. If installing ush with tiles gently
apply pressure around the outside of the mirror and allow all
adhesives to fully cure before powering up your mirror heating.
If you’re using mechanical xings, ensure they are not within
10mm of the heater pad.
PRO TIP
To avoid damage to the mirror, do not over tighten xings and
ensure that no point pressure is applied to the mirror.
6
Light
PIR
HEATING | WALL | MIRROR
PIR
Light
Thermomirror
Switch
Ensure mains supply
is RCD protected
!
Wiring to a light circuit
ThermoSphere mirror heater requires a mains supply, marshalling
box and a switch or PIR sensor. Measure and mark out all the
necessary items before you install the electric mirror heater.
If necessary chase into the wall to accommodate xtures and
wires.
5mm Expansion Gap
Thermomirror
Ensure mains
supply is RCD
!
protected
Wiring to a PIR sensor
ThermoSphere electric mirror heaters can be wired into an existing
lighting circuit using a PIR.
Remember to position the mirror heater connection box and
power cable in the closest available position to your electrical
connection to the PIR.
ThermoSphere mirror heater
Tiles
If you are installing your mirror into a rebate within the tiles,
ensure you leave a 5mm gap around the perimeter of the mirror.
Any contact with hard materials could result in a breakage.
!
Mirror heaters can be controlled with the ThermoSphere dual
control. Connect the mirror cold tail to the secondary relay, as
shown above.