7 Day Programmable Timer
Installation & User Guide
TRTS / TRTSB
2
Installing the timer ..………………… 3
User Interface ..………….........….… 5
Setting the date & time ..…………… 6
Heating modes ..…………………..… 7
Advanced settings ..……………….… 8
Setup your heating schedule ……….. 9
Technical data ..……………………... 16
Key lock ..…………………………..… 17
Temporary override ….…………….… 18
Service and support ..……………..… 20
Contents
3
Carefully remove the back of the timer by
placing a flat head screwdriver into the slots on
the bottom of the unit and push to release.
Unplug the cable connector from the back of the
timer screen.
Connect the Thermorail towel rail to the timer as
seen in the below wiring diagram.
Installing the timer
4
Screw the back plate of the timer to the
electrical plate.
Plug the cable connector into the back of the
timer screen and connect the screen to the back
of the timer.
Installing the timer
5
User Interface
1. Day indicator
2. Key lock icon
3. Schedule mode icon
4. Manual mode icon
5. ON/OFF indicator
6. Confirm settings
7. Program button
8. Mode button
9. Power button
10. Up & down arrows
11. Time
6
Press and the time will begin to flash
Use to select the correct time
Press until the day begins to flash
(Note: Monday is Day 1)
Use to select the correct day
Press to save the settings
Setting the date and time
7
When the timer is on, press the to switch
between manual and schedule modes.
Manual Mode
In manual mode press the to set the
ON/OFF status.
Schedule Mode
In the schedule mode the timer will follow the
heating schedule that is set.
Refer to page 9 for programming instructions.
Heating Modes
8
To access the advanced settings, turn the timer
off by pressing
Press to display setting 01
Use the to adjust the settings
Press to cycle between setting 01 to 03
Press to save the settings
Advanced Settings
Menu
Description
Range
Default
01
Clock Format
12 or 24
24
02
5+2 or 7 Day
Programming
01=5+2 Day Program
02=7 Day Program
01=5+2 Day Program
03
Screen Saver
ON = Activated
OF = Not Activated
OF=Not Activated
9
Turn the timer on by pressing
To set up the heating schedule for Monday to
Friday press
The time for P1 will flash. This is the first ON
period for the day.
Use the to adjust the time to when the
heated towel rail will turn on in the morning.
Press and the ON / OF will flash.
Using the select ON for P1.
Press to set period 2, which is when the rail
will turn off. Use the to adjust the time.
Set up your heating schedule (For 5+2 Day Program)
10
Press and the ON / OF will flash.
Using the select OF for P2.
Repeat above steps for P3 and P4 and then
press
(Note: P3 is turning the heated towel rail on in
the evening and P4 is turning it off in the
evening)
If the heated towel rail is only required to be on
once a day set to OF for both P3 and P4 and
ensure that the time set for P3 and P4 is after
the time set for P2.
When Monday-Friday has been set press to
go onto the Saturday and Sunday schedule.
Set up your heating schedule (For 5+2 Day Program)
11
The time for P1 will flash. This is the first ON
period for Saturday and Sunday.
Use the to adjust the time to when the
heated towel rail will turn on in the morning.
Press and the ON / OF will flash.
Using the select ON for P1.
Press to set period 2, which is when the rail
will turn off. Use the to adjust the time.
Press and the ON / OF will flash.
Using the select OF for P2.
Repeat above steps for P3 and P4.
Set up your heating schedule (For 5+2 Day Program)
12
Turn the timer on by pressing
Change the menu option 02 to setting 02
(7 Day Program) as per instructions on page 8.
The 7 day program option means that all 7 days
are programmed to the same schedule or all 7
days are programmed individually.
Press until the day display flashes.
If programming all 7 days individually use the
to select the day to program first.
If programming all 7 days to the same schedule,
press and hold the button for about 5
seconds to select all 7 days.
Set up your heating schedule (For 7 Day Program)
13
To set up the heating schedule press
The time for P1 will flash. This is the first ON
period for the day.
Use the to adjust the time the heated
towel rail will turn on in the morning.
Press and the ON / OF will flash.
Using the select ON for P1.
Press to set period 2, which is when the rail
will turn off. Use the to adjust the time.
Press and the ON / OF will flash.
Using the select OF for P2.
Set up your heating schedule (For 7 Day Program)
14
Repeat above steps for P3 and P4 and then
press
(Note: P3 is turning the heated towel rail on in
the evening and P4 is turning it off in the
evening)
If programming all 7 days to the same schedule,
the program is now set up.
If programming all 7 days individually, press
and use the to select the next day to
program.
Set up your heating schedule (For 7 Day Program)
15
Supply voltage 230 - 240VAC
Maximum Load 16A
IP Rating IP30
Warranty 2 Years
Width 80mm
Height 120mm
Depth 45mm (27mm in wall)
Technical data
16
To lock the key pad, press and hold the for 5
seconds or until the displays. To unlock
press and hold the until the disappears.
Key Lock
17
Turning the timer onto temporary override will
allow the timer to be operated on manual until
the next programmed period.
In schedule mode, press the and the
ON/OFF display will flash.
Use to adjust the desired setting and
press to confirm.
will be displayed below the
ON/OFF display. To cancel the override setting
press .
Temporary override
18
Press to turn the timer off
Press and the hold until 04 is displayed
Press and hold for approx. 5 seconds
will display on the screen and then the
timer has been reset.
Turn the timer back on to setup the program
Factory Reset
Notes
19
Notes
20
Thermogroup AU
PO Box 822
Leeton NSW 2705
1300 368 631
sales@thermogroup.com.au
www.thermogroup.com.au
Service and support
Loading...