GAS-FIRED FURNACE
DOWN FLOW & DIRECT VENT (SEALED COMBUSTION)
MODELS: GMD1-60N and GMD1-80N
INSTALLATION AND SERVICE MANUAL
For installation in:
1. Manufactured Homes
2. Modular Homes/Buildings
3. Site Constructed—Residential (S ingle Story Dwellings)
:
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
: If the information in these i n structions is not followed exactly, a fire or explosion may
result causing property damage, personal injury, or loss of life.
: Improper installation , adjustment, alteration, service, or maintenance can cause
injury or property damage. Refer to this manual. For assistance or additional informati o n , consult
a qualified installer, service agency, or fuel supplier.
: Do not use this appliance if any part has been underwater. Immediately call a
qualified service technician to inspect the appliance and to replace any part of the electrical or
control system that has b een underwater.
PLEASE READ THESE INSTRUCTIONS PRIOR TO INSTALLATION, INITIAL FIRING, AND BEFORE
PERFORMING ANY SERVICE OR MAINTENANCE. THESE INSTRUCTIONS MUST BE LEFT WITH THE USER
AND SHOULD BE RETAINED FOR FUTURE REFERENCE BY QUALIFIED SERVICE PERSONNEL.
THERMO PRODUCTS, LLC.
POST OFFICE BOX 217
NORTH JUDSON, IN 46366
PHONE: (574) 896-2133
MG-505
ECN 5320-MA 130307
MADE IN USA
All installations and services must be performed by qualified service personnel.
1
I. SAFETY SECTION
This page and the following two pages contain various warnings and cautions
found throughout this furnace Service and Installation Ma nual. Please read and
comply with the statements on the cover and the statements below.
: This furnace is not to be used as a construction heater.
: When testing electrical equipment, always follow standard electrical
procedures and precautions.
: The area around the furnace should be kept free and clear of
combustible materials, especially papers and rags.
: This furnace uses an automatic hot surface ignition control. NEVER
try to ignite gas manually.
: If the temperature rise exceeds 85°F, the heat exchanger may fail
voiding the heat exchanger wa r r anty resulting in property damage, personal
injury or loss of life.
: Burner adjustments must be confirmed by instrumentation. Failure to
use accurate or calibrated instrumentation to setup the burner may result in
reduced efficiency, sooting, and/or the production of hazardous carbon
monoxide gas.
: Any attempt to relocate safety controls or replace safety controls with
a control that is not approved or incompatible, may result in personal injury,
substantial property damage or death.
: If you do not follow these instructions exactly, a fire or explosion may
result causing personal inj ur y, loss of life or property damage.
: HAZARD OF ASPHYXIATION: Negative pressure inside the closet with
closet door closed and the furnace blower operating shall be no more negative
than minus 0.05 inch water c olumn.
: Do not obstruct any return air openings, including the return grille on
the furnace. To do so may cause the furnace to activate the high limit and shut
down or it may cause asphyxiation.
: Because of the potential of odorant fade, a gas leak may not be
detected by smell. If this furnace is installed below grade, contact your gas
supplier for a gas detector.
: All gas pipe connections must be l eak tested using a strong soap a nd
water solution (with the gas turned on). Any leaks must be repaired immediately
All installations and services must be performed by qualified service personnel.
2
after turning off the gas supply. A final test for gas leakage must be made after
purging the gas line.
: DO NOT wet electronic components during the leak test. Wetting
electronic components may damage circuitry and cause a hazardous situation.
Dry moisture from all leads and terminals if wetting occurs. Wait at least 24
hours for the circuit to fully dry before energizing the system.
: The furnace and its gas valve must be disconnected from the gas
supply during pressure testing of the gas supply system at pressures in excess
of 1/2 PSIG or 14.0 inches W.G. The furnace can be isolated from the gas supply
by closing its manual shut off valve at test pressures equal to or less than 1/2
PSIG or 14.0 inches W.G.
: Copper and brass tubing and fittings (except tin lined) shall not be
used if the gas contains more than a trace (0.3 grains per 100 cubic ft.) of
hydrogen sulfide gas. Check w i th your gas supplier.
: If you suspect there is a problem with the furnace, the venting system
or any other related problem, immediately contact a qualified service agency. If a
service agency is not available, contact your fuel supplier.
: Personal injury, or property damage, could result from major repair or
service of this furnace by anyone other than a qualified contractor. Only the
routine maintenance descri bed in the user section of this manual should be
performed by the user.
: Do not block or obstruct air openings on the furnace or air openings
communicating with the area in which the furnace is installed.
: Do not allow the outside air intake to be bl ocked or obstructed by
vegetation, ice, snow or any other materials.
: Do not use this furnace if any part has been underwater. Immediately
call a qualified service agency to inspect the furnace and to replace any part of
the electrical or control system, which has been underwater.
: Should overheating occur or the gas supply fail to shut off, shut off the
manual gas supply valve to the furnace before shutting off the electrical supply.
All installations and services must be performed by qualified service personnel.
3
WARNING:
If you do not follow these instructions exactly, a
fire or explosion may result causing property damage,
personal injury or loss of life.
390540
1. Set thermostat to lowest setting, and, if equipped , set the operating
mode to "COOL" or "OFF".
2. If service is to be performed, turn off all electric power to the
appliance.
3. To turn off gas control valve, remove the burner compartment cover.
4. Move the gas control switch to the "OFF" position.
5.
Replace the burner compartment cover.
1. STOP! Read the safety information above on this label.
2. Set the thermostat to the lowest setting.
3. Turn off all electric power to the appliance.
4. This appliance is equipped with a hot surface igniter that
automatically lights the burner. D o not try to lig ht the burner by
hand.
5. Move the gas control switch to the "OFF" position.
6.
Wait five (5) minutes to clear out any gas. Then sm e ll for gas,
including near the floor or ground. If you smell gas, STOP! Follow
"B" in the safety information above on this label. If you don't smell
gas, go to the next step.
7. Move the gas control switch to the "ON" position.
8. Turn on all electric power to the appliance.
9. Set thermostat to desired setting, and, if equ ipped, set the operating
mode to "HEAT".
10.If appliance will not operate, follow the instructions "To Turn Off
Gas To Appliance" and call your service technician or gas supplier.
A. This appliance does not have a pilot. It is equipped with a hot
surface igniter that automatically lights the burner. Do not try to
light the burner by hand.
B. BEFORE OPERATING smell all around the appliance area for gas.
Be sure to smell next to the base of unit because some gas is
heavier than air and will settle on the floor or ground.
WHAT TO DO IF YOU SMELL GAS
?
Do not try to light any appliance.
?
Do not touch any electric switch; do not use any phone in your
building.
?
Immediately call your gas supplier from a neigh bor's phone.
Follow the gas supplier's instructions.
?
If you cannot reach your gas supp lier, call the fire department.
C.
Use only your hand to move the gas control switch. Never use tools.
If the switch will not move by hand, don't try to repair it, call a
qualified service technician. Force or attempted repair may result in
a fire or explosion.
D.
Do not use this appliance if any part has been underwater.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and any gas
control which has been underwater.
This page and the followi ng page contain reproductions of the various warning
and instruction labels placed on the Thermo Pride Gas Furnace. Please read and
comply with the contents of these labels.
All installations and services must be performed by qualified service personnel.
4
All installations and services must be performed by qualified service personnel.
5
TABLE OF CONTENTS
SECTION BEGINNING PAGE
I. SAFETY SECTION 1
II. GENERAL INSTRUCT IONS AND CLEARANCES 6
III. FURNACE SPECIFICATIONS 8
IV. INSTALLATION 10
A. ROOF JACK 10
B. STANDARD CHIMNEY 10
C. FURNACE LOCATION 10
D. BASE INSTALLATION 12
1. Combustible Floor Base Model: 70-BASE 12
2. Cottage Base Model: 01COT-BASE 13
E. ALCOVE INSTALLATION 14
F. CLOSET INSTALLATION 15
G. COMBUSTION AIR 16
H. GAS PIPING 18
I. ELECTRICAL WIRING 19
J. INITIAL STA RT UP 21
K. ADJUSTMENT OF B TU INPUT RATE 21
L. BURNER ADJUSTMENT 23
M. SETTING TEMPERATURE RISE 24
N. FURNACE CHECKOUT PROCEDURE 25
V. I NSTALLER’S INSTRUCTIONS TO USER 26
VI. STARTI NG THE UNIT 27
A. SEQUENCE OF OPERATIONS 27
VII. TROUBLESHOOTING 29
VIII. DEALER MAINTENANCE 35
A. ELECT RICAL 35
B. BURNERS 35
C. INDUCER BLOWER ASSEMBLY 36
D. INSPECTING THE VENTING SYSTEM 36
E. GASKETS/SEALING MATERIALS 37
F. HEAT EXCHANGER 37
G. HOUSE AIR BLOWER 37
H. EXTENDED SHUTDOWN 37
IX. USERS INFORMATION SE CTION 38
A. W ARNINGS & CAUTIONS 38
B. COMPONENT LOCATIO NS 39
C. INSPECTION AREAS 39
D. FILTER LOCAT ION AND CLEANING 40
APPENDIX A – REPLACEMENT PARTS 41
APPENDIX B – WIRING DIAGRAM 43
All installations and services must be performed by qualified service personnel.
6
II. GENERAL INSTRUCTIONS AND CLEARANCES
NOTE: READ THIS SECTION BEFORE STARTING INSTALLATION
1. This furnace is equipped with orifices for operation with natural gas. For conversion to propane gas, see instructions in Gas Conversion Section of this manual.
2. Any reference to L.P. or Propane gas in this manual, any other labels, or markings on this furnace is to be construed to be propane HD-5. A commercial grade of liquefied petroleum gases composed of a minimum of 90 percent liquid propane (C8H8).
3. The selection of a furnace heating capacity for a proposed installation should be
based on a heat loss calculation made according to the manuals provided by the
Air Conditioning Contractors of America (ACCA) or the American Society of
Heating, Refrigeration and Air Conditioning Engineers, Inc. (ASHRAE).
4. It is recommended that a commercial available CO alarm be installed in
conjunction with any fossil fuel burning appliance. The CO alarm shall be
installed according to the alarm manufacturer’s installation instructions and be
listed in accordance with the latest edition of the UL Standard for Single and
Multiple Station Carbon Monoxide Alarms, UL 2034, or the CSA International
Standard, Residential Carbon Monoxide Alarming Devises, CSA 6.19.
5. The installer shall be familiar with and comply with all codes and regulations
applicable to the installation of these heating appliances and related equipment.
In lieu of local codes, the installation shall be in accordance with the current
provisions of one or more of the following standards.
a. Federal Manufactured Home Constructions & Safety Standard (HUD Total 24,
Part 280).
b. American National Standard (ANSI-119.2/NFPA-501C), for installations of all
recreational vehicles.
c. American National Standard (ANSI-Z223.1/NFPA-54), for installation of all gas-
fired furnaces.
d. American National Standard Electric Code (ANSI-C1/NFPA-70), for installation of
all electrical field wiring.
The gas-fired furnace has been investigated under the ANSI Z 21.47-CAN/CGA 22.32001 CENTRAL FURNA CE test standard. This gas fired unit is listed by Intertek
Testing Services and described as, “For installation as central furnace special type for
single story dwelling.”
All installations and services must be performed by qualified service personnel.
7
FRONT
BOTTOM OF DUCT
6”
1”
18”
1”
: The area around the furnace must be kept free and clear of
combustible materials, especially papers and rags.
: This furnace is not to be used as a construction heater.
6. Definitions of "combustible" and "non-combustible" materials as presented in the
1999 version of the National Fuel Gas Code, ANSI Z223.1-1999/NFPA 70-1999, are
as follows:
a. Combustible material:
“...materials made of or surfaced with wood, compressed
paper, plant fibers, or other materials that are capable of
being ignited and burned. Such materi al shall be
considered combustible even though flame proofe d, fireretardant treated, or plastered.”
b. Non-combustible material:
“...material that is not capable of being ignited and
burned; such as material consisting entirely of, or a
combination of, steel, iron, brick, tiles, concrete,
slate, asbestos, glass, and plaster.”
This heating appliance must be installed with clearances to combustible material
surfaces of not less than the minimum distances given below. Also, allow ample
clearances for servicing the furnace for easy access to the air filter, blower assembly,
burner assembly, controls, and vent connections.
MODELS GMD1-60N and GMD1-80N CLOSET ALCOVE
BACK
SIDES
ROOF JACK
VENT CONNECTOR
TOP
PLENUM SIDES
TOP AND SIDES OF DUCT
0”
0”
0”
6”
1”
1”
1”
0”
0”
0”
6”
1”
1”
1”
All installations and services must be performed by qualified service personnel.
8
III. FURNACE SPECIFICATIONS
MODEL GMD1-60 GMD1-80
HEAT INPUT RAT E (BTUH) 60,000 80,000
HEATING CAPACITY (BTUH) 49,000 65,000
BURNER ORIFICE-NAT. GAS (MM) #38 2.45
BURNER ORIFICE-PROP. GAS (DMS) #52 #53
GAS SUPPLY PRESSURE (IN.W.G.)
MINIMUM REQUIRED
PROPANE 11 11
NATURAL 5.5 5.5
MAXIMUM ALLOWED
PROPANE 14.0 14.0
NATURAL 14.0 14.0
GAS MANIFOLD PRESSURE (IN. W.G.)
PROPANE 10 + 0.3 10 + 0.3
NATURAL 3.5 + 0.3 3.5 + 0.3
VENT PIPE SIZE (INCHES) 4 4
DESIGN TEMPERATURE RISE (°F) 70 70
SEASONAL EFFICIENCY
(AFUE*, %) 82 81
*AFUE - INCLUDES STEADY STATE THERMAL EFFICIENCY AND OFF CYCLE
LOSSES.
ELECTRICAL RATINGS AND SETTINGS:
ELECTRICAL SUPPLY: 115 VAC / 60HZ / 1 PHASE
MAXIMUM TIME DELAY TYPE FUSE OR HACR BREAKER RATING: 15 AMPS
TOTAL RATED CURRENT (AMPS): 7.15 (G MD1)
NOMINAL HEAT ANTICIPATOR SETTING -- 0.8 mA (GMD1)
DIMENSIONS & WEIGHTS:
CABINET: WIDTH - 18 I N., DEPTH – 25-3/4 IN., HEIGHT - 57 IN.
NO.70 MOBILE HOME BASE: WIDTH - 18-5/16 IN., DEPTH - 24¼ IN., HEIGHT - 4 IN.
WARM A IR DUCT: WIDTH – 12 IN., DEPTH – 12 IN.
COTTAGE BASE: WIDTH – 18-3/16 IN., DEPTH - 24¼ IN., HEIGHT – 14 IN.
FILTER QUANTITY & SIZE: 1 – 18” x 24 “
APPROXIMATE SHIPPING WEIGHT: 165 LBS.
PRODUCT LISTED UNDE R ETL FILE NUMBER –
All installations and services must be performed by qualified service personnel.
9
MEDIUM LOW
SPEED:
MEDIUM HIGH
SPEED:
MEDIUM LOW
SPEED:
MEDIUM HIGH
SPEED:
BLOWER DATA
GMD1-60
MANUFACTURER: MORRISON PRODUCTS, INC.
BLOWER MODEL: 10-7, DIRECT DRIVE
NOMINAL MOTOR POWER OUTPUT (HORSEPOWER): 1/3
TYPICAL AIRFLOW @ SPECIFIED EXTERNAL
STATIC PRESSURES (SCFM @. IN.W.G.):
ESP (IN W.C.) 0.2 0.5
LOW SPEED: 759 694
907 809
1096 934
HIGH SPEED: 1207 1029
GMD1-80
MANUFACTURER: MORRISON PRODUCTS, INC.
BLOWER MODEL: 10-9, DIRECT DRIVE
NOMINAL MOTOR POWER OUTPUT (HORSEPOWER): 1/3
TYPICAL AIRFLOW @ SPECIFIED EXTERNAL
STATIC PRESSURES (SCFM @. IN.W.G.):
ESP (IN W.C.) 0.2 0.5
LOW SPEED: 712 640
HIGH SPEED: 1258 1003
870 760
1100 886
ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
All installations and services must be performed by qualified service personnel.
10
IV. INSTALLATION
A. ROOF JACK
The roof jack assembly and accessories must be listed by a nationally recognized
testing agency for the appropriate heating fuel.
The roof jack assembly must be installed according to the vent manufacturer’s
instructions prior to the furnace installation. (Refer to Figure 2 for flue location on
furnace.) Adapters for pitched roofs as well as extended barrel length roof jacks are
available from other suppliers.
All vent seams and connections must be sealed with high temperature silicone caulk.
B. STANDARD CHIMNEY
When installed as a central furnace special type for single story dwelling, venting into a
metal vent system approved by a nationally recognized testing agency for the
appropriate heating fuel type is permitted. Lined masonry chimneys are acceptable
when sized appropriately. The minimum chimney size should equivalent to the inside
free area of the 4-inch diameter vent collar exiting the furnace, or 12.5 square inches.
Maximum chimney sizes and acceptable installation practices are referenced in the
following publication. When installing the GMD1-80N, refer to Appendix G of the latest
edition of the installation standard NFPA 54, National Fuel Gas Code.
C. FURNACE LOCATION
1. For best performance, locate the furnace so that it is centralized with respect to the
duct system.
2. This furnace is only intended for installation with free air return through the furnace
door louvers. CAUTION: DO NOT connect a ducted return air system directly to
the furnace. Improper installation may create a fire hazard and damage internal
equipment, as well as void all manufacturers’ warranties.
3. This furnace may be installed on combustible flooring when utilizing either the No. 70
counterflow floor base, for below the floor duct systems, or with the cottage base, for
floor level air distribution. See Figures 1A and 1B for depictions of the No. 70 and
the cottage bases.
4. This furnace is listed for closet, alcove, or freestanding applications. All applications
must comply with the requirements of this manual.
All installations and services must be performed by qualified service personnel.
11
Combustible Floor Base
Model: 70-BASE
Figure 1A
Cottage Base
Model: 01COT-BASE
Figure 1B
Coil Cabinet
Model: CE111S / CE211T
Figure 1C
CE111S CE211T
All installations and services must be performed by qualified service personnel.
12
D. BASE INSTALLATION
1. Combustible Floor Base Model: 70-BASE Use the base bottom panel as a template to mark floor opening locations (see Figure 2). Cut a square opening in the floor for the supply air connector duct. Cut the opening 1-inch larger than the square template opening. (duct requires 1-inch clearance to combustible floor). Cut a combustion air duct opening in the floor 1/8inch larger than the template opening.
Figure 2
After cutting openings in the floor, place the bottom panel in position. Mark the
square opening location on the distribution duct at the connection point of the
connector duct. Remove the bottom panel. Cut an opening in the distribution duct
slightly larger than the connector duct. (refer to Figure 2 for location of this cut.) Cut
the connector duct to length. Install the connector duct. Bend over each tab. Insure
an airtight seal by using high temperature sealant or tape on the joint. Reinstall the
bottom panel over the connector duct. Insert and secure the combustion air duct. Put
the base top assembly in place (see Figure-3).
CAUTION: A combustion air duct must be used. If the underside of the mobile
home is skirted or enclosed (e.g. enclosed in a crawlspace), the combustion air
intake should exit through the skirting, or enclosure, if at all possible. All joints
and seams of supply ducts and c om bustion air ducts must be closed with a
sealing method suitable to the appli cation conditions and temperatures (e .g. high
temperature silicone caulk and/or aluminum tape).
All installations and services must be performed by qualified service personnel.
13
If the combustion air passageway cannot terminate outside of the skirting or
enclosure, a permanent opening with a minimum of 50 square inches of
unobstructed infiltration (free area) for ventilation air must be provided for
adequate combustion. This perma nent opening must be located no less tha n 12
inches from the bottom of the enclosure or skirting.
Figure 3
Slit the corners of connector duct down to the top of the base assembly. If metal
projects more than 1-inch above the top of the base assembly, trim the flanges down
to 1-inch. While the top of distribution duct is being pulled up with one hand, bend
down each side of the connector duct tightly to the base assembly with the other
hand. This assures a tight connection between the base assembly and the connector
duct and that the distribution duct will be full size. Use high temperature tape and/or
high temperature silicone caulking on all joints and seams to minimize air leakage.
Secure the base assembly to the floor with two screws in the front flange.
2. Cottage Base Model: O1COT-BASE
The O1COT-BASE cottage base (Figure 1B) is required for a freestanding cottage
base installation. The cottage base is designed to permit the installation of a 6-inch x
14-inch register in each of the two side panels and the front panel.
All installations and services must be performed by qualified service personnel.
14
CAUTION: A permanent opening with a minimum of 50 square inches of
unobstructed infiltration (free area) for ventilation and combustion air must be
provided to the interior of the structure. Additiona l m ake-up air may need to be
supplied to the interior of the structure to compe nsate for exhaust fans,
appliances, or vents, which consume air from the interior of the structure.
Refer to the assembly installation instructions included with OM1COT-BASE cottage
base for additional information.
3. Coil Cabinet: CE111S / CE211T
The CE111S / CE211T coil cabinet (figure 1C) is for applications requiring air
conditioning. The coil cabinet is designed to have the combustion air brought in
from the bottom thru a flexible hose, supplied with the cabinet. Refer to section G
Combustion air of this manual for further instructions on the combustion air
termination and connections. For additional information refer instructions provided
with the coil cabinet.
E. ALCOVE INSTALLATION
In this application, a minimum of 18
inches of clearance must be provided
to the front of the unit. Refer to
Figure 4.
Alcove installations must use the No. 70 mobile home base.
Note – access to diagnostic view port.
Refer to section G. COMBUSTION AIR
for additional combustion air
requirements.
Figure 4
All installations and services must be performed by qualified service personnel.
15
F. CLOSET INSTALLATION
WARNING: HAZARD OF
ASPHYXIATION: A suction
effect will occur when the
furnace is operating inside the
closet with the closet door
closed. For proper operation,
the furnace blower shall create
no more than a 0.05-inch water
column pressure differential
between the closet and the
adjoining space.
Figure 5
1. The return air opening into the closet is to have a minimum free area of 250 square
inches, (refer to Figure 5).
2. The return air opening may be located in the top, the center or (ideally) the bottom of
the closet door, or sidewall.
: Do not obstruct any return air openings, including the return grille on
the furnace. To do so may cause the furnace to activate the high temperature
limit and shutdown, or it may cause asphyxiation.
3. The cross-sectional area of the return air grille leading into the closet (when located
in the floor or ceiling) shall not be less than 250 square inches.
All installations and services must be performed by qualified service personnel.
16
4. The total free area of openings in the floor or ceiling registers serving the return air
system must be at least 350 square inches. At least one register must be located
where it is not likely to be covered by carpeting, boxes, furniture, or any other
objects.
5. Materials located in the return air system must have a flame spread classification of
200 or less.
6. Wiring materials located in the return air duct system must conform to Article 300-22
of the latest edition of the National Electrical Code, NFPA 70.
7. Gas piping shall not be located in, or extend through, the return air duct system.
8. Refer to section G. COMBUSTION AIR for additional combustion air requirements.
G. COMBUSTION AIR
CAUTION: Flexible, spiral, or corrugated duct is not recommended, due to the
relatively high-pressure drop associated wi th a ir movement through this type of
passageway.
The furnace requires the proper amount of combustion airflow through the combustion
air intake to combust the fuel cleanly and efficiently. An inadequate combustion air
supply can result in unsafe and erratic operation of the burner, sooting of the
combustion chamber and the heat exchanger, and possibly, offensive fuel odors. Refer
to chapter 5.3 of the National Fuel Gas Code, ANSI Z223.1 / NFPA 54-1999, or latest
edition for application specific combustion air requirements.
The preferred location of the outside combustion air intake terminal (e.g. an optional
stainless steel intake hood, part no. AOPS7402) is through the side of the structure,
skirting, or enclosure. An acceptable alternate location is under the structure in the
skirted or crawlspace area providing a minimum of 50 square inches of free area exists
around the perimeter for outside combustion air to be drawn through. The opening of
the termination must be at least 7 inches below the top of the floor.
The 70-base/coil cabinet is shipped with a combustion air duct that must be installed in
the bottom of the base enclosure, before the furnace is installed. This 2-inch by 7-inch
duct is shipped in two pieces. High temperature silicone sealant should be applied to
both vertical seams, before it is snapped together with all four flanges on the same end.
High temperature silicone must be applied to the flanges. The combustion air duct can
then be inserted through the opening in the floor base model no.70. When the
combustion air duct has been inserted completely, secure the duct to the combustion
adapter with self-tapping sheet metal screws, refer to Figure 6. Make certain that the
flanges, duct, and adapter are completely sealed to the burner enclosure base with high
temperature silicone caulk. A 3-inch round to 7-inch x 2-1/4 inch rectangular adapter
All installations and services must be performed by qualified service personnel.
17
plate is supplied with the furnace for adapting the 3-inch round flex combustion air duct
to the 2-inch x 7-inch combustion air duct.
Recommended materials for the combustion air duct are smooth, round, galvanized
steel duct or schedule 20 PVC pipe. The maximum intake duct length allowed is
equivalent to 40-feet of straight duct. Reduce this length by 6-feet for the intake hood
and each 90-degree elbow used, and by 3-feet for each 45-degree elbow used the
combustion air duct.
Optional combustion air - a 4” round duct may be used by connecting a 3 x 4 reducer
to the 3” flex duct supplied with the furnace.
Figure 6
All installations and services must be performed by qualified service personnel.
18
H. GAS PIPING
: Because of the potential of the odorant to fade, a gas leak may not be
detected by smell. If this furnace is installed below grade, contact your gas
supplier for a gas detector.
: With the gas piping pressurized, al l gas piping connections must be
leak tested using a strong soap and water solution. Any leaks must be repaired
immediately after turning off the gas supply. A final test for gas leakage must be
made after purging the gas line.
: DO NOT wet electronic components during the leak test. Wetting
electronic components may damage circuitry and cause a hazardous situation.
Dry moisture from all leads and terminals if wetting occurs. Wait at least 24
hours for the circuit to fully dry before energizing the system.
: The furnace and its gas valve must be disconnected from the gas
supply during pressure testing of the gas supply system at pressures in excess
of 1/2 PSIG (13.9 inches W.G.). The furnace can be isolated from the gas supply
by closing the manual gas shutoff valve serving the appliance at test pressures
equal to, or less than, 1/2 PSIG or (13.9 inches W.G.).
: Copper and brass tubing and fittings (exce pt tin l i ned) shall not be
used if the gas contains more than a trace (0.3 grains per 100 cubic ft.) of
hydrogen sulfide gas. Check w i th your gas supplier.
Sizing and installation of fuel lines must be in accordance with federal, state, and local
regulations.
A qualified installer or service person must install all gas piping and perform all required
testing.
Piping from the natural gas meter to the furnace shall be in accordance with
requirements of the local gas utility. Piping from the propane tank to the furnace must
follow the recommendations of the gas supplier. In the absence of local codes
governing gas piping selection and installation, follow the National Fuel Gas Code,
ANSI Z223.1 / NFPA 54-1999, or latest edition.
A readily accessible, manual gas shutoff valve (design-certified for the applicable gas)
with a non-displaceable rotor member shall be installed within six (6) feet of the
furnace.
A pipe union, or flanged connection, shall be provided directly up stream of the burner
to allow burner removal. Unions must be of a ground joint type or flange-jointed type
using a gasket resistant to the corrosive effects of LP gases. Pipe dope or sealant
All installations and services must be performed by qualified service personnel.
19
design-certified to be resistant to the action of the LP gases should be used on all
threaded joints.
The burner is setup to be piped to the gas supply through the left-hand side of the
furnace. For service purposes, it is recommended the gas union be located inside the
furnace.
A drip leg must be used on both propane and natural gas installations immediately
upstream of the furnace in order to trap oil, condensate, and other impurities which
might otherwise lodge in the gas valve, or plug the main burner orifice. A drip leg shall
be provided at the outlet of the gas meter when there is excessive condensation
between the gas meter and the furnace.
Failure to install drip leg(s) may void the manufacturer’s limited warranty on the furnace.
For natural gas, the maximum supply pressure is 14.0 in. W.G. and the minimum
supply pressure, for purposes of input adjustment, is 5.5 in. W.G.
For propane gas, the maximum supply pressure is 14.0 in. W.G. and the minimum
supply pressure, for purposes of input adjustment, is 11.0 in. W.G.
I. ELECTRICAL WIRING
: When testing electrical equipment, always follow standard electrical
procedures and precautions.
All electrical wiring must be installed in strict accordance with local ordinances and
codes. In the absence of local ordinances and codes, all electrical wiring must conform
to the requirements of the National Electric Code, ANSI/NFPA 70-1999, or latest
edition.
1. Electrical Branch Supply Circuit
Route all electrical wiring to the left side of the furnace. The power supply circuit to
the furnace must be installed and grounded in accordance with the provisions of the
National Electrical Code, ANSI/NFPA-70-1999, or latest edition, and all local codes
having jurisdiction.
2. Connection Of Power Supply Wires
a. Remove the cover from junction box.
b. Insert 115 VAC wires through the strain relief bushing (or conduit connection as
applicable) on the left side of the furnace junction box.
c. Connect the “hot” wire to the black wire
.
d. Connect the “neutral” wire to the white wire.
e. Connect the “ground” wire to the green wire.
All installations and services must be performed by qualified service personnel.
20
Maximum Recommended
Thermostat Wire Length
24
55
22
90
20
140
18
225
f. Reinstall and secure the junction box cover with the original mounting screws.
3. Connection Of Room Thermostat Wires
NOTE: Class 1 thermostat wire must be used inside the furnace burner
compartment.
a. Insert 24 VAC wires through the plastic grommet on the left side of the furnace
casing.
b. Connect the thermostat wires to the W/R 50A65-143 control (refer to the wiring
diagram).
c. Connect the thermostat wires to the room thermostat.
IMPORTANT: The room thermostat should be installed 4 to 5 feet above the floor
on an interior wall which is relatively free from direct sources of heat (sunlight or
supply airflow) or exposure to cold (drafts from open windows and doors). The
nominal anticipator setting is 0.8 amperes, for the GMD (refer to the thermostat
literature for additional information).
Five-conductor thermostat wire is recommended for 24 VAC, low-voltage, control
circuit wiring. How ever only 2 wires are required for the furnace (a heating
application only).
Electrical Wire Diameter
(AWG)
(Feet)
Once the furnace is installed, check the thermostat anticipator for proper nominal
setting.
1. Connect a multimeter, capable of reading milliamps (mA), in series
with the low voltage wires to the thermostat.
1. Increase the thermostat setting, or create a “call for heat”.
2. Read the value of the thermostat current, in milliamps.
3. Adjust the heat anticipator of the thermostat to the value read by the
multimeter.
If the heat anticipator is set too high, the furnace may delay activation of a heating
cycle for too long. If the heat anticipator is set too low, the furnace may cycle too
frequently. Either condition may not provide optimal comfort to the homeowner.
All installations and services must be performed by qualified service personnel.
21
J. INITIAL START UP:
This furnace does not have a pilot. It is equipped with a hot surface igniter, which
automatically lights the burner. Do not attempt to light the burner by hand. Check the
following items before the initial start-up.
1. Check all wiring for proper hook up. Tighten any loose connections.
2. Using a soap solution, leak test gas piping connections.
3. Check all tubing connections to the pressure switch, inducer, burner box, and gas
valve and make sure they are connected firmly at all their connection points.
4. Check flue pipe, combustion air inlet, and all joints for tightness and to make sure
there is no blockage.
5. Make sure air filter is in place.
6. Make sure the outside vent and air intakes are installed according to instructions
and are free from blockage.
OPERATING INSTRUCTIONS:
: Turn off power to furnace before it is placed into service. The gas
piping system must have been leak tested by a qualified heating contractor. (See
Section IV, H, of these instructions on the installation of gas piping).
: It may be necessary to purge the air out of the gas line for initial startup of the furnace after installation. A qualified heating c ontractor should do this.
If excessive gas escapes when purging the gas supply at the union, allow the
area to ventilate for at least 15 minutes before attempting to start the furnace.
Propane gas is especially dangerous because the specific gravity of propane gas
allows it to accumulate at floor level at a dangerous concentration.
: Heat exchanger oil will burn off on initia l firing creating a n unpleasant
odor. To prevent this odor from occurring more tha n once, it is suggested that:
1. A window(s) be opened.
2. The thermostat be set at highest setting.
3. The furnace remains running at conditions 1&2 for 30 minutes or until odor
has dissipated.
K. ADJUSTMENT OF HEAT INPUT RATE:
The orifices for this furnace were sized: 1) for natural gas having a heating value of
1025 BTU per cubic foot and a specific gravity of .65, or 2) for liquefied propane gas
with a heating value of 2500 BTU per cubic foot and a specific gravity of 1.55. The
rating label inside the furnace vestibule will specify which gas your furnace is orificed
for. If the furnace is installed at an altitude that is more than 2,000 feet above sea level,
it is mandatory the input to the burner be reduced 4.0% for every 1,000 feet that it is
above sea level. If the furnace is installed at an elevation of 5,000 feet, its input must
be reduced 20.0%. Example: a furnace rated at 80,000
All installations and services must be performed by qualified service personnel.
22
MAX 14” WC
MIN 5.5” WC
BTU at sea level must be reduced to a firing rate of 64,000 (80,000 x .80 = 64,000) at
an elevation of 5,000 feet. If the furnace is installed at an elevation of 2,000 feet or
less, no reduction in input is required. Your gas supplier may supply you with the
correct orifice sizing information.
To check the heat input rate of your natural gas furnace, allow the unit to operate for 10
to 15 minutes and proceed as follows:
a. Call your gas supplier and ask for the BTU content (heating value) of one cubic foot
of the gas, supplied to the installation area. An alternate approach is to assume a value
of 1025 BTU/Cu Ft, which is the national average.
b. With all other gas appliances turned off and using a stopwatch, clock the time
required for the (small) dial on the gas meter to make one full revolution. The meter
dial will state the cubic feet of flow for one revolution usually one, two or five.
FORMULA: BTU/Cu Ft x Number of Cu Ft x 3600 Seconds = Input BTU/hr
Seconds for one revolution
EXAMPLE: 1025 BTU/Cu Ft x 2 Cu Ft x 3600 = 78,678 BTU Input
93.80 Seconds
Check the model number of the furnace, the input rate, the type of gas, and the
manifold pressure on the rating label located in the burner vestibule. If using the above
example, the furnace is a GMD1-80N model and the input rate is 78,678 BTU/hr. The
input rate would be acceptable because it was within + 2% of the listed input of 80,000.
c. Make sure that the gas supply pressure to the furnace is within the allowable range of
5.5" to 14" WC pressure on natural gas and 11.0" to 14.0" W C on propane gas. The
pressure to the furnace must be checked while the furnace burner and any other gas
appliances on the same supply system are operating, using the 1/8 in. NPT manifold
pressure tap shown in figure 8.
GAS PRESSURE CHART FOR ALL GMD1-60 and GMD1-80 MODEL
FURNACES
SUPPLY PRESSURE MANIFOLD PRESSURE
NAT
PROPANE
MAX 14” WC
MIN 11” WC
3.5 + .3” WC
10.0” + .3” WC
TABLE 2
All installations and services must be performed by qualified service personnel.
23
This gas furnace is equipped with a fixed orifice sized for the manifold pressure shown
on the rating label. The input can only be increased, or decreased, by adjusting the
manifold pressure. Remove the 1/8" threaded pipe plug located on the gas manifold.
Use a U tube manometer or recently calibrated pressure gage to measure the pressure.
To adjust the pressure, remove the screw cap from the regulator on the gas valve and
using the adjustment screw. Decrease the pressure by turning the screw
counterclockwise or increase it by turning the screw clockwise.
CAUTION: ADJUSTMENTS TO THE LISTED PRESSURE MUST NOT EXCEED
0.3" WC A 0.3" WC adjustment will increase or decrease the input approximately 4.0%.
Replace screw (cap) when adjustment is complete.
The correct input can be assumed if the furnace manifold pressure is the same as that
shown on the rating label if a gas meter is not available for natural gas or the unit is
installed on an unmetered propane gas supply.
Shut off the gas supply to the furnace. Remove the pressure gage and re-install the
pipe plug using a thread compound resistant to the action of LP gases.
If the rated input cannot be obtained with the present orifice at the correct pressure,
your local gas supplier may assist in sizing the proper orifice. Thermo Products
Engineering Department will gladly assist in sizing the orifice if you provide them with
the heating value in BTU per cubic foot and the specific gravity of the fuel gas.
L. BURNER ADJUSTMENT
: The GMD1-60 and GMD1-80 furnace models utilize an in-shot burner
design that does not require an air shutter adjustment (air shutters are not used)
for proper flame characteristics. Burner box access cover must always be
secured with all screws in place and tightened before operating furnace.
This unit is designed to not require any burner adjustment. The flames should be
checked by looking through the sight glass located on the burner box. Burner flames
should be clear, blue, and almost transparent in color. (See Figure 8). NOTE: It is not
unusual to have mostly blue flames with yellow or orange tips visible in the tube for
propane gas.
All installations and services must be performed by qualified service personnel.
24
Figure 8
M. SETTING TEMPERATURE RISE
The GMD1-60N and GMD1-80N is designed and wired at the factory for a heating
blower speed that should result in an approximate temperature rise of 70°F.
The blower motor is wired on low speed for heating mode of the GMD1-60N.
The blower motor is wired on medium low speed for heating mode of the GMD1-80N.
The temperature rise through the furnace may vary depending on the duct system,
elevation, heating value, etc. for each installation.
After 10 to 15 minutes of continuous operation, the temperature rise through the
furnace must fall within a range of 55°F to 85°F. If the outlet or supply duct
temperature is too high, check to make sure the return air filter is clean, the return air
registers are free from obstruction, the outlet registers are properly adjusted and clear,
and the supply and return air ducts are open.
The circulating air blower is not moving enough air if the supply air temperature is still
too high. Before proceeding further, turn off the power supply to the furnace and
remove the blower door. The speed of the blower must be increased by changing the
speed tap from the motor (see wiring diagram). This is accomplished by locating the
control panel attached to the blower housing and switching the blower lead, which
should be connected to the “Heat” terminal on the White-Rodgers 50A65-143 control,
with one of the higher speed blower leads attached to a terminal marked “Park”. Be
sure to attach any unused blower leads to a terminal marked “Park”. Replace the
blower door and turn on the power supply.
All installations and services must be performed by qualified service personnel.
25
N. FURNACE CHECKOUT PROCEDURE
Before any system of gas piping is finally put into service, it shall be carefully tested to
assure that it is gas tight as indicated in section IV. H. Gas Piping of this manual.
NOTICE: All controls on the unit should be checked for proper functioning prior to the
qualified service personnel leaving the job site. Specifically the following should be
checked:
With furnace in normal heating operation, check to make certain blower will start and
stop automatically under control of integrated fan control.
1. Check safety limit control as follows:
a. Shut off incoming power.
b. Block return air opening or disconnect blower motor leads.
c. Restore power to furnace.
d. Set thermostat above room temperature calling for heat.
e. When high air temperatures are reached in furnace at limit control setting with
blower out of operation, burner should shut off.
f. Shut off electrical power.
IMPORTANT: Remove blockage or reconnect blower motor and restore power.
2. Make certain thermostat will automatically start and stop furnace.
3. Block the flue pipe outlet gradually until the pressure switch functions shutting off
the main burners.
4. Block the inlet gradually until pressure switch functions shutting off the main burners.
IMPORTANT: Remove flue or air inlet blockages when done.
All installations and services must be performed by qualified service personnel.
26
V. INSTALLER'S INSTRUCTIONS TO USER:
After completing the installation, the installer shall inform and/or demonstrate to the
homeowner:
1. The location of all the instructions in the furnace must be kept along with
instructions for any accessories in the plastic pouch near the furnace.
2. The location and use of the manual gas shut off valve and furnace electrical
disconnect switch. Instruct user to always shut off gas before shutting off electric
power.
3. The sequence of operation of the furnace.
4. The correct operation and maintenance of the appliance as outlined in the Users
Information section of this manual.
5. That failure to maintain and operate this furnace in accordance with these
instructions could result in hazardous conditions, bodily injury, and property
damage and may void the limited warranty on the furnace.
6. Review with and encourage the user to read the label reproductions and all
warnings and instructions outlined on the front cover and in sections I, II and III of
this manual and in the Users Information section of this manual.
7. Recommend the user has a qualified heating contractor inspect the furnace at the
start of each heating season. Inform the user of the frequency of inspection
required for reach item in the User Information Section of this manual.
8. Should the furnace not operate after installation – note diagnostic code through
view port prior to removing door.
All installations and services must be performed by qualified service personnel.
27
FLAME MUST BE
DETECTED WITHIN
4 SECONDS I F FLAM E
IS DETECTED, THE
DELAY-TO-FAN-ON
TIME BEGINS (45 SECONDS)
IF FLAME IS NOT
DETECTED, THE GAS VALVE
IS DE-ENERGIZED, THE
IGNITOR IS TURNED OFF AND
THE CONTROL BOARD CONTROL
GOES INTO "RETRY" SEQUENCE
POWER IS APPLIED TO
THE SILICON NITRIDE
IGNITOR. IGNITOR
WARM-UP IS 20 SECONDS
POWER INTERRUPTION
SYSTEM SHUTS OFF,
RESTARTS WHEN
POWER IS RESTORED.
PRESSURE SWITCH SENSES
ADEQUATE DIFFERENTIAL
PRESSURE CONTACTS CLOSE
THERMOSTAT CALLS FOR
HEAT, CONTACTS CLOSE
CONTROL BOARD ENERGIZED,
INDUCER ENERGIZED
CONTIN UO US SAFE OPERATION CHECK IF FLAM E
SIMULATION CONDITION PRESENT OR ROLL-OUT
SWITCH OPENS, SYSTEM ENERGIZES INDUCER
FAN FOR 15 SECONDS AND CI RCULATOR BLOWER
AT HEATING SPEED UNTIL SITU ATION CORR ECTION
AT ANY TIME THE
GAS VALVE IS
NOT ENERGIZED
A. SEQUENCE OF OPERATIONS
START TRIAL
FOR IGNITION
START
AFTER IGNITOR WARM-UP,
THE GAS VALVE IS
ENERGI ZED TO OPEN
VI. STARTING THE UNIT
All installations and services must be performed by qualified service personnel.
28
AFTER DELAY-TO-FAN--ON
PERIOD ENDS, CIRCULATING
AIR FAN IS ENERGIZED AT
HEATIN G SPEED. THE
(OPTIONAL) ELECTRONIC
AIR CLEANER AND
HUMIDIFIER ARE ENERGIZED.
IF IGNITION ATTEMPT IS
UNSUCCESSFUL, ONE
MORE RETRY WILL BE
MADE BEFORE THE
CONTROL BOARD GOES
INTO SYST EM LOCK OUT.
THE RETRY SEQUENCE
PROVIDES A 60 SECOND
WAIT BEFORE IGN ITION
RETRY. RETRY IS
ATT EMPTED WITH AN
ADDITIONAL 10 SECONDS
OF IGNITOR WARM-UP TIME.
IF FLAME IS DETECTED,
THEN LOST, THE CONTROL
BOARD WILL REPEAT THE
INITIAL IGNITION SEQUENCE
FOR A TOTAL OF SIX
RECYCLES. AFTER SIX
UNSUCCESSFUL RECYCLE
ATT EMPTS, THE CO N TROL
WILL GO INTO SYSTEM
LOCKOUT.
AFTER THE DELAY-TO-
FAN-OFF PERIOD ENDS,
THE CIRCULATING AIR
FAN AND (OPTIONAL)
ELECTRONIC AIR CLEANER
ARE DE-ENERGIZED.
MAIN
BURNER
OPERATION
END OF CYCLE
CALL
FOR HEAT
SATISFIED
IF SYSTEM IS IN LOCKOUT, THE
MODULE WILL RESET ITSELF
AFTER 60 MINUT ES OR MA Y
BE MANUALLY RESET BY
INTERRUPTING THE POWER
TO THE FURNACE AT THE
DISCONNECT OR INTERRUPTING
THE CALL FOR HEAT AT THE
THERMOSTAT. IF THIS DOES
NOT RESTART THE SYSTEM,
REFER TO THE TROUBLESHOOTING
SECTIO N O F THIS MANUAL.
WHEN THERMOSTAT IS
SATISFIED, CONTACTS
OPEN AND THE GAS
VALVE IS DE-ENERGIZED.
AFTER PROOF OF FLAME
LOSS, INDUCER START S
5 SECOND POST SURGE
AND (OPTIONAL) HUMIDIFIER
IS DE-ENERGIZED. THE
DELAY-TO-FAN-OFF PERIOD
BEGINS (180 SECONDS)
All installations and services must be performed by qualified service personnel.
29
VII. TROUBLESHOOTING
THIS SECTION IS ONLY TO BE PERFORMED BY TRAINED, QUALIFIED SERVICE
PERSONNEL, AND NOT BY THE FURNACE OWNER.
NOTICE: BEFORE TROUBLESHOOTING, FAMILIARIZE YOURSELF WITH THE
START UP AND CHECKO UT PROCEDURE. ALL INSTALLATION AND
SERVICES MUST BE PERFORMED BY QUALIFIED HEATING CONTRACTORS
When testing electrical equipment, always follow standard electrical
procedures and precautions.
Note – check diagnostic code through view port prior to removal of door.
1. Check for line voltage (110-120VAC) to the furnace. If there is no line voltage
applied to the furnace, check that disconnecting switch is “on”, fuses or circuit
breakers have not blown or tripped.
2. Make sure thermostat is “calling for heat”.
3. Check for adequate fuel supply and pressure. Are all the fuel shutoff valves
open?
4. To assist you in troubleshooting this furnace, it is equipped with an integrated
ignition control with diagnostics. These diagnostics evaluate what malfunction
the control system has experienced and will activate a flashing light on the
control in different sequences to help pinpoint the failure.
All installations and services must be performed by qualified service personnel.
30
DIAGNOSTIC FEATURES
: Power must be disconnected before servicing.
The 50A65-143 control continuously monitors its own operation and the operation of the
system. If a failure occurs, the LED will indicate a failure code as shown below. If the
failure is internal to the control, the light will stay on continuously. In this case,
the entire control should be replac ed, as the control is not field-repairable.
If the sensed failure is in the system (external to the control), the LED will flash in the
following flash-pause sequences to indicate failure status (each flash will last
approximately 0.25 seconds, and each pause will last approximately 2 seconds).
1 flash, then pause System lockout
2 flashes, then pause Pressu re switch stuck closed
3 flashes, then pause Pressu re switch stuck open
4 flashes, then pause Open limit switch or rollout switch
6 flashes, then pause 115 Volt AC power reversed
7 flashes, then pause Low flame sense signal
8 flashes, then pause Check igniter or improper grounding
Continuous flashing Flame has been sensed when
(No pause) no flame should be present
(No call for heat)
The LED will also flash once at power-up.
All installations and services must be performed by qualified service personnel.
31
TURN THERMOSTAT TO CALL FOR HEAT
DOES THERMOSTAT MAKE CONTACT?
REPLACE TRANSFORMER
CHECK INPUT
POWER, SERVICE
SWITCH AND FUSES
IS INTERNAL DAMAGE
PRESENT ON THE
TRANSFORMER?
ARE WIRES CONNECTED
PROPERLY?
CORRECT WIRE
CONNECTIONS
COOL THE THERMOSTAT
IS ROOM TEMPERATURE
BELOW THERMOSTAT
SETTING?
TURN T'STAT
SETTING ABOVE
ROOM TEMP.
REPLACE
THERMOSTAT
IS THE TRANSFORMER
SUPPLYING 24 VOLTS
TO THE THERMOSTAT?
CHECK FOR
CONTINUITY
& PROPER
CONNECTIONS
IS THE INDUCER
BLOWER OPERATING?
Yes
Yes
No
NoNo
Yes
No No
Yes Yes
Yes
No
No No
YesYes
IS ROOM
TEMPERATURE
ABOVE
90 DEGREES F?
IS THERE 24 VOLTS
ACROSS "TH" & "TR"
AT THE INTEGRATED
CONTROL?
TROUBLESHOOTING GUIDE
THE SYSTEM IS STARTED BY SETTING THE THERMOSTAT TO CALL FOR
HEAT. THE FOLLOWING SHOULD HELP ESTABLISH THE TYPE OF
MALFUNCTION OR DEVIATION FROM THE NORMAL OPERATION.
TO USE THIS DIAGRAM, FOLLOW THE INSTRUCTIONS IN THE BOXES.
NOTE: CHECK DIAGNOSTIC CODE THROUGH VIEW PORT PRIOR TO REMOVING ACCESS DOOR.
All installations and services must be performed by qualified service personnel.
32
CHECK THE INT EGRATED
CONTRO L DIAGNOST IC LED
LAMP. RESET BY INTERRUPT I NG
POWER TO CONTROL FOR MORE
THAN ONE SECOND. IF LED ST A YS
ON CONT INUOUSLY, REPLACE
INTEGRATED CONTROL.
CHECK WIRING TO INDUCER
AND IF OK, REPLACE
INDUCER ASSEMBLY.
DOES THE HO T
SURFACE
IGNITOR ENERGIZE
AND GLOW?
CHECK THE INT EGRATED CONTRO L
DIAGNOSTIC LED LAMP. RESET BY
INTERRUPT ING POWER TO CO NTROL
FOR MOR E THAN O NE SECOND. IF
LED STAYS ON CONTINUOUSLY
REPLACE I NT EGRATED CONTROL.
IS THERE LINE VOLTAGE
ACROSS HOT SURFACE
IGNITOR TERMIN ALS
"IGN" & "IGN N" AT T HE
INTEGRATED CONTROL?
CHECK WIRING TO HOT
SURFACE IGNITOR AND
IF OK, REPLACE HOT
SURFACE IGNITOR ASSEMLBY.
CHECK WIRING TO GAS
VALVE AND IF O K,
REPLACE GA S VALV E.
CHECK ACROS S "MV"
TERMINAL S O N INTEGRATE D
CONTRO L FOR 24 VOL TS DURING
THE 4 SECOND FLAME PROVING
PERIOD AFTER IGN IT OR WARM-U P.
IS THERE 24 VO LTS?
SAME AS ABOVE
AFTER HOT
SURFACE IGNITOR
WARM-UP, DOES
GAS VAL VE OPEN ?
Yes
No No
Yes
Yes Yes
No
Yes
No
Yes
No
Yes
IS THERE LINE VOLTAGE
ACROSS I NDUCER PO WER
TERMINALS "IND" & "IND N"
AT THE IN TEG RATED CONTROL?
All installations and services must be performed by qualified service personnel.
33
AFTER GAS VALVE
OPENS, DO THE
BURNERS IGNITE?
MEASURE MANIFOLD
PRESSURE. IS
PRESSURE ADEQUATE?
ADJUST TO 3.5" WC FOR
NATURAL GAS O R 10.0" WC
FOR PROPANE GAS
CHECK IGNITOR
VOLTAGE DURING
20 SECOND WARM-UP,
IT SHOULD BE AT
LEAST 105 VOLTS.
CORRECT LINE
VOLTAGE PROBLEM.
IS IGNITOR
POSITIONED
CORRECTLY?
REPOSITION TO
CORRECT LOCATION.
DO BURNERS STAY
LIT PAST PROOF
OF FLAME CHECK?
CHECK FLAME
PROVING CIRCUIT
DOES THE INTEGRATED
CONTROL ENERGIZE THE
CIRCULATING AIR
BLOWER AFTER THE 45
SECOND TIME DELAY?
CHECK ACROSS THE
CIRCULATING AIR
BLOWER TERMINALS
"CIR N" & "HEAT"
FOR PROPER VOLTAGE.
REPLACE THE
INTEGRATED CONTROL.
DOES THE CIRCULATING
AIR FAN COME ON
WHEN ENERGIZED?
DOES BLOWER
SPIN FREELY?
CONFIRM IF EITHER
BLOWER WHEEL IS
RUBBING AGAINST
HOUSING OR MOTOR
SHAFT IS SPINNING
FREELY AND REPAIR
OR REPLACE AS
NECESARRY.
REPLACE MOTOR
IS CAPACITOR
WORKING PROPERLY?
REPLACE CAPACITOR
Yes
Yes
Yes
Yes
Yes
No No
Yes
No
Yes
No
No
No No
No
Yes
Yes
No
No
All installations and services must be performed by qualified service personnel.
34
TROUBLESHOOTING COMPLETE.
CHECK ALL
WIRI NG FOR
LOOSE
CONNECTIONS
IS LED LI G HT
ON INTEGR ATED
CONTROL FLASHING?
DOES SYSTEM RUN UNTIL
THERMOSTAT IS SATISFIED?
DOES BURNER SHUT OFF
WHEN THERMOSTAT IS
SATISFIED?
CHECK FOR SHORT IN
WI RE TO THERMOSTAT
AND CORRECT IF
NECESSARY.
DOES THE CIRCULATING
AIR BLOWER TURN OFF
AFTER THERMOSTAT IS
SATISFIED WITHI N
120 SECO NDS?
Yes
Yes
No No
Yes
No
Yes
Yes
IF LED FLASHES:
1 FLASH , THEN PAUSE SYSTEM LOCKOUT
2 FLASH ES, THEN PAUSE PRESSURE SWITC H STUCK CLOSED
3 FLASH ES, THEN PAUSE PRESSURE SWITC H STUCK OPEN
4 FLASH ES, THEN PAUSE OPEN LIMIT SWITCH OR ROLLOUT SW ITCH
6 FLASH ES, THEN PAUSE 115 VOLT AC POWER RE VERSED
7 FLASH ES, THEN PAUSE LOW F LAME SENSE SIGNAL
8 FLASHES, THEN PAUSE CHECK IGNITOR OR IMPRO PER GROUNDING
CONTINUOUS FLASHI NG FLAM E HAS BEEN SENSED WHEN NO FLAME
(NO PAUSE) SHOULD BE PR ESENT (NO CALL FOR H EAT)
THE LED WILL ALSO FLASH ONCE AT POWER-UP.
CHECK COMPLETE SYSTEM OU T.
LED LIGHT STAYS ON CONTINUOUSLY,
COMPLETE FAILUR E - REPLACE INTEGRATED CONTR OL.
All installations and services must be performed by qualified service personnel.
35
VIII. DEALER MAINTENANCE
A qualified heating contractor should perform the following maintenance procedures at the beginning of each heating season. Correct any deficiencies at once.
WARNING: Personal injury or property damage could result from repair or
service of this furnace by anyone other than a qualified heating contractor. Only
the homeowner/user routine maintenance described in the User s Information
Manual may be performed by the user.
WARNING: To avoid injury from moving parts, shut off the power to the
furnace before removing blower compartment door.
CAUTION: Label wires prior to disconnection when servic i ng controls. Wiring
errors can cause improper and dangerous operation.
A. ELECTRICAL:
1. Check all wiring for loose connections and any signs of damage or unusual wear.
2. Check for correct voltage at the furnace when operating.
3. Check amp-draw on blower motor and inducer motor to assure they are not exceeding nameplate amp rating.
4. Check for correct operation and proper settings (if manually adjustable) of all controls.
Shut off gas and disconnect pow er before continuing.
B. BURNERS
If it appears that material is accumulating in the burner box, the burner box cover can
be removed and the box and burners can be vacuumed. If necessary, the burners
assembly can be removed by taking out the two screws/one on each bracket on top of
burner box and removing the burner manifold assembly (See Fig. 9). Assembly must
be pulled & tilted down in order to remove from box. If necessary, the individual tubes
can be cleaned out using compressed air to blow out the individual tubes. Care must
be taken not to damage the igniter.
All installations and services must be performed by qualified service personnel.
36
Figure 9
C. INDUCER BLOWER ASSEMBLY
Inspect the pressure switch and tubing connections and inspect the blower/assembly
for warpage, deterioration and carbon or other build-up. If necessary, clean the
accessible portions of the housing and blower with a damp cloth. Vacuum to remove
any lint or dust from the motor assembly.
D. INSPECTING THE VENTING SYSTEM
The venting system should be inspected during the annual maintenance check-up or
during each subsequent service call.
Check all vent pipes for restrictions due to soot, or carbon build-up, as well as foreign
matter, or any materials, that cause the venting system to restrict the proper venting of
combustion products. If a restriction is found, the flue vent must be cleaned or
replaced to ensure proper venting.
All installations and services must be performed by qualified service personnel.
37
Vent pipes should also be inspected for any signs of corrosion, deterioration, or leakage
that may cause combustion by-products to infiltrate the home or indoor environment.
If signs of corrosion, deterioration, or leakage are evident, the vent pipe must be
replaced with a properly sized, agency-approved, vent pipe.
E. GASKETS/SEALING MATERIALS
Inspect all visible gaskets for signs of degradation, especially any seals which were
removed as part of the inspection. Replace any suspect gaskets.
F. HEAT EXCHANGER
Inspect for corrosion, pitting, warpage, deterioration, carbon build-up, and loose gaskets
in the flue pipe, burner box, and accessible areas of the heat exchanger.
G. HOUSE AIR BLOWER
Check and clean the blower wheel, housing, and compartment with a vacuum. Check
the motor nameplate and follow the motor manufacturers instructions for lubrication, if
required.
IMPORTANT: Some motors are permanently lubricated and should not be oiled.
See motor nameplate for specific instructions.
H. EXTENDED SHUTDOWN
If this furnace is shut down or off for an extended period of time, several steps can be
taken to help insure a smooth and reliable start.
ON SHUT DOWN:
1. Close the gas supply shutoff valve(s).
2. Turn the furnace power switch “off” and disconnect electrical power to the unit.
ON START-UP:
1. Have the heating system (and furnace) inspected and started by a qualified
service person.
2. Set the room thermostat above room temperature.
3. Open all shutoff valves in the gas supply line.
4. Turn “on” the main power at the disconnecting switch and at the furnace power
switch to start the inducer.
5. Follow the “BURNER OPERATION AND ADJUSTMENT” procedure in Sectio n J.
All installations and services must be performed by qualified service personnel.
38
IX. USER INFORMATION SECTION
A. WARNINGS AND CAUTIONS:
: If you suspect there is a proble m w ith the furnace, pertaining to the
venting system or any other related problem, immediately contact a qualified
service agency. If a service agency is not available, contact your fuel
supplier.
: Personal injury or property dam age could result from major repa i r
or service of this furnace by anyone other than a qualified contractor. The
user should only perform the routine maintenance described in the us er
section of this manual.
: The area around the furnace should be kept free and clear of
combustible materials, especially papers and rags.
: Do not block or obstruct air openings on the furnace casing. Do not
block or obstruct air openings communicating within the area in which the
furnace is installed.
: Do not allow the outside air intake to be bl ocked or obstructed by
vegetation, ice, snow, or any other materials.
: Do not use this furnace if any part has been underwater.
Immediately call a qualified service agency to inspect the furnace and to
replace any part of the electrical or control system, which has been
underwater.
: Should overheating occur or the fuel s upply fail to shut off, shut off
the manual fuel supply valve to the furnace before shutting off the electrical
supply.
All installations and services must be performed by qualified service personnel.
39
B. COMPONENT LOCATIONS
The following diagram shows a typical furnace installation and typical position of
the components referenced in these instructions.
Figure 10
C. INSPECTION AREAS
IMPORTANT: For safe operation it is the responsibility of the owner and/or user
that the burner, chimney/vent pipe, heat exchanger and control s should be
inspected every year by a qualified heating contractor.
All installations and services must be performed by qualified service personnel.
40
1. VESTIBULE: The furnace vestibule areas or burner compartment should be
inspected by removing front door of the furnace and looking for signs of
excessive heat such as discoloration of components, materials damaged
from rust or corrosion, soot or carbon build-up.
2. EXTERIOR OF FURNACES: The furnace exterior should be inspected for
signs of excessive heat such as discoloration of materials or damage from
rust or corrosion.
3. VENT CONNECTOR: The furnace vent pipe should be inspected for signs of
rust, corrosion pitting, or holes in the pipe. Check for leakage around seams
in pipe indicated by soot or condensate streaks.
4. ROOF JACKS: The furnace roof jack should be inspected for signs of rust or
corrosion, pitting or holes, signs of excessive condensation or moisture
leaking from roof jack.
D. FILTER LOCATION AND CLEANING
CAUTION: To avoid injury from moving part, hot surfaces or electrical
shock, shut off the power to the furna ce and allow the furnace to cool
before removing furnace access door to service filter.
The air filter should be inspected each month and cleaned when dirty. Clean the
filter by soaking it in water with a mild detergent and rinsing it with clean water.
Allow the filter to air dry before reinstalling it in the furnace. Cleaning the air filter
frequently may prevent airborne contaminants from going through the furnace
and depositing in the furnace, duct system, and interior of the building.
See Figure 10, in this section, for the location of the return air filter.
All installations and services must be performed by qualified service personnel.
41
APPENDIX A – REPLACEMENT PARTS
All installations and services must be performed by qualified service personnel.
42
All installations and services must be performed by qualified service personnel.
43
APPENDIX B – WIRING DIAGRAM
Loading...