Therma-Tru Light Commercial Doors and Frames User Manual
Therma-Tru® Light Commercial/Multi-Family - Doors and Frames
SHEET NUMBER:
OF
JOB NUMBER:
ARCHITECT:
LOCATION:
PROJECT:
FINISHED HARDWARE BY:
CONTRACTOR:
RECORD OF SUBMITTALS
SUBMITTED
RETURNED
1st
2nd
3rd
4th
RECORDED APPROVED DRAWINGS
DRAWN BY:
RECORDED APPROVED HARDWARE
OUTSIDE
LEFT HAND INSWING
OUTSIDE
RIGHT HAND INSWING
OUTSIDE
LEFT HAND REVERSE
OUTSIDE
RIGHT HAND REVERSE
SINGLE DOORS
OUTSIDE OUTSIDE
OUTSIDE OUTSIDE
LEFT HAND ACTIVE RIGHT HAND ACTIVE
LEFT HAND REVERSE ACTIVE RIGHT HAND REVERSE ACTIVE
PAIRS OF DOORS
• Material shown on these drawings will be
fabricated only after formal approval by the
architect, receipt of approval hardware schedule,
and all necessary hardware templates.
• All frames shall be shipped “knocked-down”
unless otherwise specied.
• All frames and doors shall be chemically washed,
rinsed, and dried prior to receiving one coat of
paint.
• Doors and frames will be reinforced for surface
mounted hardware as required. Drilling and
tapping for surface mounted hardware shall be
applied by others.
• It will be the responsibility of the General
GENERAL NOTES
Contractor to coordinate hardware locations.
• All frames will be supplied with the required wall
and oor anchors as illustrated on the frame detail
sheet.
DOOR HANDING CHART • All standard type hardware will be located at this
LEFT HAND REVER SE/
RIGH T HAN D OUTS WING
LEFT HAND REVER SE ACTI VE/
RIGH T HAN D OUTS WING AC TIVE
SINGLE DOORS
PAIRS OF DOORS
RIGH T HAN D REVE RSE/
LEF T HAN D OUTS WING
RIGH T HAN D REVE RSE ACT IVE/
LEFT HAND OUTSW ING ACT IVE
manufacturer’s standard locations as shown on
the door and frame elevations. Hardware items
such as panic exit devices, deadbolts, etc. will also
be located at manufacturer’s standard locations
unless specically advised.
• Installations of all glass and glazing to be
performed by others.
• Doors, frames, and nished hardware to be
installed by others.
• Anchor bolts and expansion shields for any type
fastener to be furnished by others.
• All frames must be set absolutely plumb, square,
and level.
• All frames will be supplied with rubber door
silencers: three for single swing openings and two
per header for double swing openings.
• All frames and doors wll be tagged with shop
marks. This schedule can be used to cross
reference shop marks with architects marks.
• These drawings are not intended for use by other
trades.
• Field welding, grinding, nishing, and attachment
of eld splices by others.
1
REMARKS
WIDTH HEIGHT
JOB NUMBER
PROJECT
SHEET NUMBER
OF
LOCATION
LOCK
CLOSER
FLUSH BOLTS
HRDWR. SET/ HDG.
GAUGE
SHEET ELEV.
LABEL
HINGE
JAMB DEPTH
OVERALL HEIGHT
ANCHOR
DOOR CONSTR.
DOOR OPENING
DOOR THICK.
SHEET ELEV.
SHEET SECT.
ITEM
QUANTITY
ARCH MARK
FROMTOSWING
FRAME CONSTR.
GAUGE
LOCATION
FRAME DATA
DOOR DATA
HARDWARE
Therma-Tru® Light Commercial/Multi-Family - Schedule
2
Therma-Tru® Light Commercial/Multi-Family - 22-Gauge & 24-Gauge Steel Doors
EXPOSED GLASS
SIZE: 3” x 33”
EXPOSED GLASS
SIZE: 4” x 25”
EXPOSED GLASS
SIZE: 5” x 20”
3”
4”
5”
33”
25”
20”
EXPOSED GLASS
SIZE: 10” x 10”
EXPOSED GLASS
SIZE: 22” x 28”
EXPOSED GLASS
SIZE: 22” x 34”
10”
28”
34”
EQUAL
EQUAL EQUAL EQUALEQUAL
EQUAL
10” 22” 22”
DOOR ELEVATIONS - FLUSH - LITED
DOOR ELEVATIONS - EMBOSSED - OPAQUE
STY LE# 500STY LE# SE978H DSTY LE# SE969H DSTY LE# SE960H DSTY LE# 514STY LE# SE210H D
3
DOOR ELEVATIONS - SMOOTH
DOOR ELEVATIONS - GRAINED
Therma-Tru® Light Commercial/Multi-Family - FG Doors
STY LE# SSF960STY LE# SSF200ST YLE# SS F16 0STYLE # S SF100
STY LE# FCF160STY LE# FCF 140STY LE# FCF100
4
Loading...