Therma-Tru Double-door, Swing-in User Manual
Classic-Craft Door System Specifications
⎠
DOOR PANELS
OPTIONAL
FACTORY-GLAZED
GLASS OR GLASS
INSERTS
OPTIONAL
DECORATIVE PANELS
Faces: 3/32-inch minimum thickness, molded from proprietary thermoset composite,
wood-grained to duplicate hand-crafted red oak master, stainable and paintable. Door
edges: machinable kiln-dried clear northern red oak, flush and square with door faces,
lock edge reinforced with full-length 3-1/2-inch wide engineered lumber core. Door
bottom edge: moisture-proof and decay-proof composite. Core: foamed-in-place
polyurethane, CFC-free, density 2.0 pcf minimum, K-factor of 0.15 for minimum
thermal transmittance. Standard factory sizes may be edge trimmed or end trimmed in
shop or fieldto suit replacementdoor size requirements.
Factory-glazed (available in sidelites):
integral part of skin, molding details match door panel moldings. Glass: minimum 1/8inch tempered, two thicknesses with sealed airspace between, air-space typically 1/2inch. Options for leaded decorative glass triple-glazed in airspace between tempered
glass faces with solid brass or zinc caming. Etched glass options. Optional removable
red oak woodgrilles.
Inserts (lites):
wood grained to match door faces, with molding patterns complementing raised panel
moldings, stainable or paintable, screw-fastened to doors, screw holes concealed with
grain-matched plugs in matching material and finish. Glass: minimum 1/8-inch
tempered, two thicknesses with sealed airspace between, airspace typically 1/2-inch.
Options for leaded decorative glass triple-glazed in air space between tempered glass
faces with solid brass caming. Options for etched glass. Optional removable red oak
wood grilles.
Molded from fiberglass-reinforced thermoset composite, wood grained to match door
faces, stainable orpaintable, fastened with veryhigh bond tape.
perimeter frames in raised-molding patterns, composite frame moldings
perimeter moldings flush with skin and made as
GASKETING,
WEATHERSTRIPPING
HINGES, STRIKES
FRAMES
SILL, SWING-IN, SWING
OUT, SIDELITE OPTIONS
TRANSOM OPTIONS
Swing-in models: , press-fit in kerfs at jamb stops in
frames. Extruded thermoplastic elastomer, finned and chambered design, press-fit into
bottom edge of doors. Corner pads at bottom margin corners from jacketed thermoset
closed-cell foam.
Steel, zinc-plated, brass finish. Optional solid brass hinges. Screws plated and finished
to match hardware. Minimum hinge size 4x4x.098 inches. Strikes are proprietary
adjustable type, permittingin-out adjustment of doorin frame, upto 3/16 inch.
Milled from 5/4 kiln-dried pine, profiled with 1/2-inch stop, minimum depth 4-9/16
inches. Other frame depths available to match wall constructions. Exterior casing
brickmould in WM180 pattern available. Optional frames in clear northern red oak or
exterior grade redoak wrap over pinewith matching brickmould. Optional maintenancefree clad framesand brickmoulds in prefinishedwhite color.
Wide range of sill options:
“monumental” grade with decay proof composite substrate, available bronze and brass
finishes, other sills available in swing-in,swing-out, aluminum, brass or bronze anodized
finish.
Double-door models:
locking astragal available,astragal faces in clearnorthern red oakto match door.
Sidelite options:
models with glass moldings to match door panel moldings, in 12-inch and 14-inch
widths. Sidelite systems available with mullions separating doors from sidelites, and
continuous sills andframe head, or asseparately framed andcased units joined together.
Transom frames, either rectangular or elliptical, match door frames and have matching
exterior brickmould. Transom frames in primed pine or clear northern red oak to match
door frame option. Clear insulated glass, etched glass or with decorative leaded glass,
detailed with solidbrass or zinc caming.
jacketed thermoset closed-cell foam
thermally-broken fixed, adjustable with oak threshold, in
double door in 6/8 height available with both leaves active and
flush-glazed lite models, raised molding models and raised panel
Issued: Oct 2008
SPEC
Door System
Specifications
Fiber-Classic Door System Specifications
⎠
DOOR PANELS
OPTIONAL
FACTORY-GLAZED
GLASS OR GLASS
INSERTS
OPTIONAL
DECORATIVE PANELS
GASKETING,
WEATHERSTRIPPING
Faces: 1/16-inch minimum thickness, fiberglass-reinforced thermoset composite,
wood-grained in natural northern red oak patterns, stainable and paintable. Door edges:
machinable kiln-dried pine, primed to match color of faces, lock edge reinforced with
engineered lumber core, lockset area reinforced with solid blocking for hardware
backup. Door bottom edge: moisture-proof and decay-proof composite. Core:
foamed-in-place polyurethane, CFC-free, density 2.0 pcf minimum, K-factor of 0.15 for
minimum thermal transmittance. Standard factory sizes may be edge trimmed or end
trimmed in shopor field to suitreplacement door sizerequirements.
Factory-glazed:
Glass minimum 1/8-inch tempered, two thicknesses with sealed airspace between airspace typically 3/8-inch. Options for grooved Bevelline,Low-E or grille between glass
(GBG). Optional removable woodgrilles.
Inserts (lites):
composite, wood grained to match door faces, stainable or paintable, screw-fastened to
doors, screw holes concealed with grain-matched plugs in matching material and finish.
Glass minimum 1/8-inch tempered, two thicknesses with sealed airspace between,
airspace typically 3/4-inch. Options for leadeddecorative glass triple-glazed in air space
between tempered glass faces with solid brass or zinc caming. Options for grooved
Bevelline glass oretched glass. Optional removablewood grilles.
Molded from proprietary composite, wood grained to match door faces, stainable or
paintable, screw-fastened to doors, screw holes concealed with grain-matched plugs in
matching material andfinish.
Swing-in models:
frames. Extruded thermoplastic elastomer, finned and chambered design, press-fit into
bottom edge of doors. Corner pads at bottom margin corners from jacketed thermoset
closed-cell foam.
Swing-out models:
with sills.
perimeter moldings flush with skin and made as integral part of skin.
perimeter frames in raised-molding patterns, molded from proprietary
jacketed thermoset closed-cell foam, press-fitin kerfs at jamb stops in
same weatherstrip as swing-in models, bottom gaskets integral
HINGES, STRIKES
FRAMES
SILLS, SWING-IN,
SWING-OUT, PATIO
DOOR, SIDELITE
OPTIONS
TRANSOM OPTIONS
SPEC
Door System
Specifications
Steel, zinc-plated, brass or chrome finish. Screws plated and finished to match
hardware. Min-imum hinge size 4x4x.098 inches. Strikes are proprietary adjustable
type, permitting in-outadjustment of door inframe, up to3/16 inch.
Milled from 5/4 kiln-dried pine, profiled with 1/2-inch stop, minimum depth 4-9/16inches. Other frame depths available to match wall constructions. Exterior casing
brickmould in WM180 pattern available. Optional maintenance-free clad frames and
brickmoulds are prefinishedwhite.
Wide range of sill options:
swing-in, swing-out, public-access,aluminum, brass or bronzeanodized finish.
Double-door and hinge patio door models:
available with both leaves active and locking astragal available, hinge patio doors in
standard 6/8 height, replacement 6/6 height and 8/0 height available, patio models
available in two-paneland three-panel options (onedoor active, othersstationary).
Sidelite options:
models with panels flush with doors all available to match doors, in 12-inch and 14-inch
widths. Sidelite systems available with mullions separating doors from sidelites, and
continuous sills andframe head, or asseparately framed andcased units, joined together.
Transom frames, either rectangular or elliptical, match door frames and have matching
exterior brickmould. Clear insulated glass or with decorative leaded glass, leaded brass
with solid brass or zinc caming. Optional removable muntins for divided-lite look in
rectangular transoms.
flush-glazed lite models, raised molding models, and raised panel
thermally-broken fixed, adjustable with oak threshold,
double door in 6/8 height and 8/0 height
Issued: Oct 2008
Loading...