Thermasol SignaTouch STCX Series Installation Manual
Installation Manual
For Tutorials and Troubleshooting visit www.thermasol.com/solutions
STCX-XXX
SignaTouch Control
OVER 60 YEARS OF STEAM SHOWER INNOVATION
SignaTouch Control Installation Instructions
1 Important Information before You Install
The SignaTouch Control must be installed
inside the shower. The ThermaTouch control
will only function on the current TFX, SSA and
PRO Series generators.
The control should be installed 60" from
the oor of the shower and away from
the steamhead.
The steamhead should be installed 24" from
the oor and 6" from any wall. Locate as far
as possible from the bathing seating area
or location of the users and not below
any xtures.
IMPORTANT: When locating and installing the
ThermaTouch, it is required to not place the
control under any water-outlets, shower heads
or in the direct path of owing water.
SEE DIAGRAM FOR LOCATION EXAMPLE.
PLEASE REVIEW WARNINGS BELOW AND LEAVE THIS MANUAL WITH HOMEOWNER
DO NOT USE THIS PRODUCT UNLESS YOU HAVE CONSULTED WITH YOUR DOCTOR AND RECEIVED WRITTEN PERMISSION TO DO SO.
USE OF THIS PRODUCT MAY BE HAZARDOUS TO YOUR HEALTH.
PLEASE CONSULT YOUR PHYSICIAN BEFORE USING. IF YOU ARE PREGNANT, ELDERLY, HAVE HIGH BLOOD PRESSURE, DIABETES,
SUFFERING FROM HEART DISEASE, ARE INTOXICATED, OR NOT IN GOOD HEALTH, DO NOT USE THIS STEAM BATH.
STEAM IS HOT! DO NOT TOUCH OR GO NEAR THE STEAMHEAD FROM THE TIME THE UNIT IS “ON,” UP TO ONE HOUR AFTER IT HAS SHUT
OFF. SEVERE BURNS WILL OCCUR IF YOU COME IN CONTACT WITH THE STEAMHEAD OR STEAM EMITTING FROM THE STEAMHEAD.
NEVER ATTEMPT TO FILL AROMA RESERVOIR ON THE STEAMHEAD WHEN UNIT IS IN THE "ON" POSITION. SEVERE BURNS WILL OCCUR.
DO NOT USE THERMASOL AROMATHERAPY OILS, SKIN CARE PRODUCTS OR ANY PRODUCT ASSOCIATED WITH YOUR THERMASOL UNIT
WITHOUT CONSULTING WITH YOUR ALLERGIST OR DOCTOR BEFORE USE. THESE PRODUCTS MAY BE HAZARDOUS TO YOUR HEALTH.
DO NOT USE STEAM ROOM WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS, AS THIS CAN BE HAZARDOUS TO YOUR HEALTH.
YOUR SHOWER MAY BE A SLIP-AND-FALL HAZARD. CHECK WITH YOUR CONTRACTOR OR FLOORING MANUFACTURER REGARDING THE
SAFE USE OF YOUR FLOORING IN A STEAM APPLICATION. SLIPPING AND FALLING INTO THE STEAMHEAD ITSELF OR INTO THE STREAM
OF STEAM EMITTING FROM THE STEAMHEAD WILL CAUSE SERIOUS BURNS OR PHYSICAL INJURY.
IF YOU ARE FEELING UNCOMFORTABLE, DIZZY, FAINT, OR STARTING TO FALL ASLEEP, IMMEDIATELY EXIT THE STEAM ROOM.
DO NOT USE STEAM ROOM IF YOU ARE UNDER THE AGE OF 16 UNLESS SUPERVISED BY AN ADULT.
THERMASOL STEAM BATH GENERATORS ARE NOT DESIGNED TO BE USED FOR SPACE HEATING PURPOSES.
THERMASOL STEAM BATH GENERATORS ARE FOR INDOOR USE ONLY. THEY SHOULD NEVER BE LOCATED OUTSIDE THE HOME.
All products must be installed in accordance with installation instructions provided. Failure to do so may invalidate warranty at
manufacturer’s discretion. ©2019 ThermaSol.
Read warnings on page 2. For illustrative purposes only. Consult with qualied professional for steam room construction details.
2
THERMASOL.COM I 800.776.0711
SignaTouch Control Installation Instructions
2 Tools and Materials
Controller
Item STCX-XXX
Materials needed:
o SignaTouch control
o M8 cable
o Silicone
o Mud Ring
o Other materials as required
Silicone Installation instructions, warranty,
Mud Ring
Item 04-8566
3 Mud Ring Application
Back of Control
Power/Data
M8 connection
static cling warning label
Top
Vertical Installation
Mud Ring goes
inside wall
opening
Shower
wall
Top
Horizontal Installation
Finished wall must be ush
with the mud ring.
Shower
wall
5.7" W by 3.9" opening for recessed mount STC-XXX Mud Ring
SignaTouch control can be installed vertically or horizontally
Read warnings on page 2. For illustrative purposes only. Consult with qualied professional for steam room construction details.
THERMASOL.COM I 800.776.0711
3
SignaTouch Control Installation Instructions
4 Control Installation and Data Cable Connection
Installation with
generator only
Shower
wall
M8 Cable
Route the M8 cable through the nished wall to the back side
of the control. (The other end of the cable runs to the steam
generator location.) NOTE: It is recommended to run the
cable through electrical conduit. DO NOT STAPLE the cable!
Installation with one of or all, SLSR, Digital
shower valve, and steam generator.
Connector
Detail
"ON"
Turn Clockwise
Contact pins
• Do not staple, strain or damage data cable
• Align pins to receptacle visually before tightening
• Do not force plug
• Hand tighten only
"OFF" Turn
Counter Clockwise
Contact pins Cable ends
DO NOT pinch, nail, staple, wedge, or
bind the data cable.
DO NOT wrap the data cable around
steam line or route it in a manner so
that the hot steam line could melt
the cable.
Any damage to the control cable
will result in the control not working
properly.
Carefully connect the data cable to
the PDM and control BEFORE turning
power on to the generator or PDM.
Connect to PDM
PDM requires 110V power
Connect the data cable to Power Distribution Module
(PDM). (The other end of the cable runs to the back of the
control in the shower location.)
Read warnings on page 2. For illustrative purposes only. Consult with qualied professional for steam room construction details.
4
THERMASOL.COM I 800.776.0711
Loading...