Thermalzone Wac8115r, Wac6115r Owner's Manual

WINDOW

AIR CONDITIONER

INSTALLATION

AND

OPERATION

950-0075-revD Page 1 of 15 9 May 2007

CATALOG NO. PRODUCT CODE

WAC6115R 420-0005
WAC8115R 420-0008

TABLE OF CONTENTS
AIR CONDITIONER SAFETY………………………………………………….….2
INSTALLATION REQUIREMENTS………………………………………………3
ELECTRICAL REQUIREMENTS…………………………………………………4
INSTALLATION INSTRUCTIONS………………………………………………..6

AIR CONDITIONER USE…………………………………………………………8
AIR CONDITIONER CARE……………………………………………………….11
TROUBLESHOOTING………………………………………………………….…11

SPECIFICATIONS………………………………………………………………….13
WARRANTY………………………………………………………………………...15

TECHNICAL SUPPORT

IF YOU NEED TECHNICAL SUPPORT, PLEASE CALL [phone] BETWEEN THE HOURS OF 8:00 A.M. and

5:00 P.M. EST.

PLEASE HAVE THE MODEL NUMBER AND SERIAL NUMBER OF YOUR EQUIPMENT AVAILABLE

WHEN YOU CALL.

AIR CONDITIONER SAFETY

Your safety and the safety of others is very important
We have provided many important safety messages in this manual and on your appliance.
Always read and follow all safety instructions.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you or others.

All safety messages will follow the safety alert symbol and the word “DANGER” or
“WARNING”.

These words mean:

followed.
Bodily injury or damage to personal property may

occur if instructions are not followed.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of
injury, and tell you what can happen if the instructions are not followed.

950-0075-revD Page 2 of 15 9 May 2007

You can be seriously injured if instructions are not

•

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electrical shock, or injury when using your air conditioner, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong

• Do not use an adapter.

• Do not use an extension cord

• Unplug air conditioner before servicing

• Use two or more people to move and

install air conditioner.

SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Gather the required tools and parts before starting installation. IMPORTANT: Observe all governing codes and ordinances.
Read and follow the instructions provided with the tools listed Check the location where air conditioner will be installed. Proper
Here. Installation is your responsibility. Make sure you have everything
necessary for correct installation.

Tools Needed
The location should provide:

• Flat-Blade and

Phillips
screwdrivers

• Level • Drill and 3/32” or

• Scissors • Utility Knife

Parts Supplied (on some models)

Check that all parts are included in the parts package.

• Tape measure

smaller bit

Grounded electrical outlet within 4 ft (122 cm) o f

where the power cord exits the air conditioner.

NOTE: Do not use an extension cord.

• Free movement of air in room to be cooled

• A large enough opening for the air conditioner

NOTE: Cabinet louvers must not be obstructed. Air must
be able to pass freely through the cabinet louvers.

950-0075-revD Page 3 of 15 9 May 2007

Window Installation ELECTRICAL REQUIREMENTS

Window opening measurements:

• 25” min to 38” max (63.5 cm to 95.5cm) opening width.

• 14” min. (35.6 cm) opening height.

Ground wire must be connected to ground screw located in lower

right corner of air conditioner when air conditioner is in cabinet.

The electrical ratings for your air conditioner are listed on the

model and serial number label. The model and serial number

label is located behind the front panel on the flange below the

Control panel area.

Specific Electrical requirements are listed in the chart below.

Follow the requirements for the type of plug on the power supply

cord.

950-0075-revD Page 4 of 15 9 May 2007

•

Recommended Ground Method

This air conditioner must be grounded. This air conditioner is
equipped with a power supply cord having a grounded 3 prong
plug. To minimize possible shock hazard, the cord must be
plugged into a mating, grounded 3 prong outlet, grounded in
accordance with all local codes and ordinances. If a mating outlet
is not available, it is the customer’s responsibility to have a
properly grounded 3 prong outlet installed by a qualified electrical
installer.

It is the customer’s responsibility to:

Copies of the standards listed may be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269

LCDI Plug and Power Cord To Test Your LCDI Power Cord：

NOTE: Your unit’s device may differ from the ones shown. 1. Plug power supply cord into a grounded 3 prong outlet.

2. Press RESET（on some devices, a green light will turn on）

3. Press TEST (Listen for a click; Reset button will trip, and on some devices,

4. Press and release RESET (Listen for a click; Reset button will
Latch and remain in). The power supply cord is ready for operation.

NOTES:

This room air conditioner is equipped with a power supply cord
required by UL. This power supply cord contains state-of-the-art
electronics that sense leakage current. If the cord is crushed, the
electronics detect leakage current, and power will be
disconnected in a fraction of a second.

• Contact a qualified electrical installer.

• Assure that the electrical installation is adequate and in

conformance with National Electrical Code, NNSI/NFPA 70­latest edition, and all local codes and ordinances.

a green light will turn on).

The reset button must be pushed for proper operation

• The power supply cord must be replaced if it fails to
trip when the test button is pressed of fails to reset

• Do not use the power supply cord as an off/on switch.
The power supply cord is designed as a protective
device.

• A damaged power supply cord must be replaced with
a new power supply cord obtained from the product
manufacturer and must not be repaired.

• The power supply cord contains no user serviceable
parts. Opening the tamper-resistant case voids all
warranty and performance claims.

950-0075-revD Page 5 of 15 9 May 2007