This product is intended for installation only by expert users. Please consult with a qualified technician for installation.
Improper installation may result in damage to your equipment.
1. Please carefully read the manual before beginning the installation process !
2. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000.
3. DO NOT USE any kind of alcohol or alcohol derivatives with this reservoir or the acrylic tube may crack and fail ! Do not clean it using alcohol either !
Installation Guide
Parts List
Cli p
Nut s
Wre nch Clip Sponge Bra cket
Bracket Sponge
G1/4 Stop Plug
Wre nch
Cab le Ties
Short Screws
Long Screws
A x 2
B x 8
C x 8
D x 1
E x 2
F x 2
G x 4
H x 2
L x 1 M x 1 N x 1 O x 1 P x 1 Q x 1
I x 1
J x 1
K x 4
F
F
G
G
H
H
I
C
C
B
B
There are two types of mounting kits,
please choose the mounting kit you want to
use (Both types can be installed together)
Install your fittings and tubes,
remember to use the bottom as
an outlet and top as an inlet.
Connect the reservoir cable to
the conversion cable.
1 2
3
A
A
B
C
D
E
E
C
B
Mor e Langu age (De utsch , Españ ol, Fra nçais , Itali ano, Po rtugu ês,
Рус ский, Tü rkçe, 简 体中文, 正體中 文, 日本語, ภาษ าไทย)
Ple ase vis it www. therm altak e.com
Support
16.8 Million Colors
Pacific
PR22-D5 Plus
Pump+Reservoir
J
O
Controller Power Cable
Velcro
Controller Cable Conversion cable
Bridge Cable
Installation Guide
4
6
5
L
M
Connect the reservoir cable onto the controller.
Set the DIP switch on the back side of the controller
to assign the number of the controller
NO .1
ON
1 2 3 4
NO .3
ON
1 2 3 4
NO .2
ON
1 2 3 4
NO .4
ON
1 2 3 4
NO .9
ON
1 2 3 4
NO .1 1
ON
1 2 3 4
NO .1 0
ON
1 2 3 4
NO .1 2
ON
1 2 3 4
NO .5
ON
1 2 3 4
NO .7
ON
1 2 3 4
NO .6
ON
1 2 3 4
NO .8
ON
1 2 3 4
7
L
C
123
45
ON
1 2 3 4
M
NO .1 3
ON
1 2 3 4
NO .1 5
ON
1 2 3 4
NO .1 4
ON
1 2 3 4
NO .1 6
ON
1 2 3 4
Connect the controller cable onto the mainboard
(USB 2.0 9 pin) and controller.
9
8
If you want to connect two or more connectors,
you can use the bridge cable to connect the
controllers.
Connect the power cable to the 4pin Molex
connecter and controller.
N N
P P
© 2017 Thermaltake Tech no lo gy C o., Ltd. All Rights Reserved.
www.thermaltake.com
After adding the recommended coolant, remember to
fill the reservoir to only 80% and leave the fill port cap
off. This will help stabilize your internal loop pressure
Keep the reservoir cap dry!
Do not allow coolant to
access the wire and
the LED module
Caution!
I
Loading...