Page 1
Pacific V-RTX 2080 Plus
Patented
Funders Edition VGA Water Block
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment.
Before you start using this product please follow these basic guidelines:
1. Please carefully read through the instruction manual before beginning the installation process.
2. Please remove your graphics card from your motherboard to insure the safest process and in order to prevent any possible damages to your CPU and motherboard.
3. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000.
16.8 Million Color
Parts List
C x 13D x 2E x 7F x 6H x 5I x 2G x 1
34
1
A x1
B x1
2
Use GeForce RTX 2080 WINDFORCE OC 8G
as demonstration, other model reference
the installation guide.
5
Detach the backplate.
6
G
Apply thermal compound
Remove original VGA stock cooler (Remove
the screws circled on the diagram. All heat sink
assembly screws should be removed)
Please confirm your VGA models before following the next step
7
Cut the thermal pads to the dimensions listed and place them on the spots shown on the diagram.
90 mm
d
d
35 mm40mm
bc
60 mm
a
90 mm
c
70 mm
b
b
60 mm
a
60 mm
a
60 mm
a
2080
2080Ti
7mm
7mm
7mm
7mm
7mm
Remove the power connector
(Carefully detach the original stock
cooler)
H
dd
H
b
Clean the original thermal compound
off the GPU die and remove the screws.
c
a
a
a
b
a
c
b
8
E
C
D
F
B
I
When installing the water block, carefully position the water block with the preinstalled standoffs
on the graphics card.
9
C
Finish
Page 2
Pacific V-RTX 2080 Plus
ON
1234
Patented
Funders Edition VGA Water Block
Parts List
Jx 1Kx 1Lx 1Mx 1Px 1Nx 1Ox 1
ControllerPower Cable
Controller Cable
Bridge Cable
LED Y - CableMB SYNC Cable
Installation Guide
10
A
N
Connect the LED Y-Cable onto the waterblock.
11
J
N
123
Connect the Waterblock onto the controller.
16.8 Million Color
Velcro
J
45
12
J
Set the DIP switch on the back side of the controller to assign the
number of the controller
13
K
K
Connect the controller cable onto the mainboard (USB 2.0 9 pin)
and controller.
1415
NO.1
ON
1234
NO.5
ON
1234
NO.9
ON
1234
NO.13
ON
1234
NO.2
ON
1234
NO.6
ON
1234
NO.10
ON
1234
NO.14
ON
1234
NO.3
ON
1234
NO.7
ON
1234
NO.11
ON
1234
NO.15
ON
1234
NO.4
ON
1234
NO.8
ON
1234
NO.12
ON
1234
NO.16
ON
1234
LL
Connect the power cable to the 4pin Molex connecter and controller.
© 2018 Thermaltake Technology Co., Ltd. All Rights Reserved.
www.thermaltake.com
MM
If you want to connect two or more connectors, you can use the bridge
cable to connect the controllers.
Page 3
+5V D G
JRAINBOW
G
Pacific V-RTX 2080 Plus
Patented
Funders Edition VGA Water Block
Mianboard SYNC installtation Guide
CAUTIONCAUTION
Please power off the PC and check
the Positive and Negative ends on
the connector before connecting
the cable to mainboard. Connecting
the wrong end can damage the LEDs.
Nx 1
LED Y - Cable
16.8 Million Color
Ox 1
MB SYNC Cable
N
Connect the MB STNC Cable to Water block
ASUS ASROCK
Aura Addressable Strip Header(s)Addressable RGB LED Header(s)
JRGB-strip Header(S)
MSIMSI
OOOO
O
GIGABYTE
AOURS RGB Fusion with Digital LEDs
© 2018 Thermaltake Technology Co., Ltd. All Rights Reserved.
www.thermaltake.com
Page 4
TT RGB Plus Software control interface
Please download software from Thermaltake Official website.
www.thermaltake.com/home.aspx
and search " TT RGB Plus " on the official website.
OS compatibility: Windows 7 / 8 / 8.1 / 10
When you open the software, choose the “VGA Plus” in the drop-down list(C-3) first.
1. Software User Interface
BB
A-1A-1
A-2A-2
D-1D-1
D-2D-2
A-3A-3
C-2C-2
C-1C-1
A. TT RGB Plus software Profile Setting
A-1 Set up a profile: Choose a Profile and set up the LED Lighting Mode,
then click the SAVE icon(A-3) to store your settings to the software.
A-2 Save a profile to controller: Select a profile and a controller,
then click the Save icon to assign the profile to the controller.
B. Follow the Installation Guide step 3, you can set up the number of the controller
C. LED Lighting Mode
Full Lighted / Wave / Pulse / Ripple / Blink / Sound Control / RGB Spectrum / Flow / Thermal...
C-1 LED Selection: set up the LEDs lighting, color, and speed.
Light Mode: Choose a lighting mode
Color Mode: Choose the LEDs color
Light Speed: Set up the speed of the LEDs light
LED Spot & Color Palette: Choose the color of each of the individual LEDs by clicking the color palette
Done: Save your setting
Default: Reset the LED setting back to the default
Brightness: Drag the mouse to adjust LED light brightness.
LED On/Off: Click the LED Light icon to turn on or off the LED light
RGB Color Code: Enter the Decimal Code of Red, Green, and Blue to set the LEDs color
C-2 LED On/Off: User can switch off the LED control function in the software if the fan is not plug into the controller.
C-3 Drop-down list: click the product name to choice another you want.
D-1 & D-2. Product Selection: click the control panel to rotate it to the front
C-3C-3
C-3C-3
VGA Plus
2. Mobile APP Connection Password
To connect the Riing Plus RGB APP, please connect the PC to your
wireless first, and click the Password setting under the software
setting menu, set up your connection password. The TT RGB Plus
APP will ask for your password every time when starting the APP.
For more information please visit www.thermaltake.com
© 2018 Thermaltake Technology Co., Ltd. All Rights Reserved.
www.thermaltake.com
English
English
正體中文
正體中文
簡體中文
簡體中文
Deutsch
Deutsch
Français
Français
日本語
日本語
ไทย
ไทย
Auto Update On
Auto Update On
Password O n
Password O n
Password :8888
Password :8888
Loading...