Page 1
20mm
20mm
Pressure Equalizer Plug
Pacific
This product is intended for installation only by expert users. Please consult with a qualified technician for
installation. Improper installation may result in damage to your equipment.
Pressure
1. Please carefully read the manual before beginning the installation process !
Equalizer
Plug
2. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000.
3. DO NOT USE any kind of alcohol or alcohol derivatives with this reservoir or the acrylic tube may crack
and fail ! Do not clean it using alcohol either !
General Information
Due to the water temperature differences between operation
and standby mode, high pressures may develop within your
loop. In order to help continuously equalize the internal
pressure of your loop and the ambient pressure, Thermaltake
Pacific series reservoir/pump combos come with the
following pressure relief kit.
Reservoir with vertical orientation
Thermaltake pacific pressure equalizer plug
is designed to be installed on top of your
reservoir if you reservoir is in vertical
orientation. The pressure equalizer plug
allows air and pressure to automatically
pass through the fitting preventing pressure
buildup in your loop.
equal iz er p lu g
Pre ss ur e
A x 1
Press ur e
equal iz er p lu g
A
Parts List
B x 1
Pacif ic 1 /2 ” ID x 3 /4 ”
OD Co mp re ss io n
C x 1
Pacif ic 1 /2 ”
Fill- po rt
D x 1
V-Tu bl er 4 T 1/2 ” OD ,
3/4”I D 10 0m m
Caution
1. Do not soak the pressure equalizer plug in
water / coolant
2. Please drain your loop and seal the fill port
with stop plug before transporting your PC
Reservoir with horizontal orientation
Thermaltake pacific pressure equalizer plug is designed to be installed on the highest
point of your loop allowing air and pressure to pass through the fitting preventing
unnecessary pressure buildup. To properly exhaust the air out of your loop, you will
need to install a compression fitting and a fill port on any of the ports located on the
reservoir. Then mount the pressure equalizer plug to your fill port while keeping the
pressure equalizer plug at the highest possible point in your system.
Pre ss ur e eq ua li ze r pl ug
A
Pacif ic 1 /2 ”
C
Fill- po rt
V-Tu bl er 4 T 1/2 ” OD ,
D
3/4 ”I D 10 0m m
Caution
1. Do not soak the pressure equalizer
plug in water / coolant
2. Please drain your loop and seal the
fill port with stop plug before
transporting your PC
Pacif ic 1 /2 ” ID x 3 /4 ”
OD Co mp re ss io n
B
© 2015 Th er ma lt ak e Tech no lo gy C o. , Lt d. Al l Ri gh ts R es er ve d. w ww. the rma lt ake .co m
Page 2
20mm
20mm
Pressure Equalizer Plug
Pacific
This product is intended for installation only by expert users. Please consult with a qualified technician for
installation. Improper installation may result in damage to your equipment.
Pressure
1. Please carefully read the manual before beginning the installation process !
Equalizer
Plug
2. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000.
3. DO NOT USE any kind of alcohol or alcohol derivatives with this reservoir or the acrylic tube may crack
and fail ! Do not clean it using alcohol either !
General Information
Due to the water temperature differences between operation
and standby mode, high pressures may develop within your
loop. In order to help continuously equalize the internal
pressure of your loop and the ambient pressure, Thermaltake
Pacific series reservoirs come with the following pressure
relief kit.
Reservoir with vertical orientation
Thermaltake pacific pressure equalizer plug
is designed to be installed on top of your
reservoir if you reservoir is in vertical
orientation. The pressure equalizer plug
allows air and pressure to automatically
pass through the fitting preventing pressure
buildup in your loop.
Press ur e
equal iz er p lu g
A
A x 1
Press ur e
equal iz er p lu g
Parts List
B x 1
Pacif ic 1 /2 ” ID x 3 /4 ”
OD Co mp re ss io n
C x 1
Pacif ic 1 /2 ”
Fill- po rt
D x 1
V-Tu bl er 4 T 1/2 ” OD ,
3/4”I D 10 0m m
Caution
1. Do not soak the pressure equalizer plug in
water / coolant
2. Please drain your loop and seal the fill port
with stop plug before transporting your PC
Reservoir with horizontal orientation
Thermaltake pacific pressure equalizer plug is designed to be installed on the highest
point of your loop allowing air and pressure to pass through the fitting preventing
unnecessary pressure buildup. To properly exhaust the air out of your loop, you will
need to install a compression fitting and a fill port on any of the ports located on the
reservoir. Then mount the pressure equalizer plug to your fill port while keeping the
pressure equalizer plug at the highest possible point in your system.
Pre ss ur e eq ua li ze r pl ug
A
Pacif ic 1 /2 ”
C
Fill- po rt
V-Tu bl er 4 T 1/2 ” OD ,
D
3/4 ”I D 10 0m m
Caution
1. Do not soak the pressure equalizer
plug in water / coolant
2. Please drain your loop and seal the
fill port with stop plug before
transporting your PC
Pacif ic 1 /2 ” ID x 3 /4 ”
OD Co mp re ss io n
B
© 2015 Th er ma lt ak e Tech no lo gy C o. , Lt d. Al l Ri gh ts R es er ve d. w ww. the rma lt ake .co m
Loading...