
1
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
Intel 775/1150/1151/1155/1156/1366
Heatsink Body Fan Clip
TY-147B
Screw Nut
Anti-Vibration Pads
Mounting Plate
M3L6 Screw
Anchoring Mount
Intel Washer
(small)
Mylar Film
Backplate cap
Metal Back Plate
Motherboard
M3L10 Screw

The Ultimate Cooling Solutions!
www.thermalright.com
2
Component
1
1
2
2
3
3
4 5 6
7 8
9
9
10
13
16 17
16 1715
11
14
12
12
14
13
1110
Le GRAND MACHO
Heatsink Body ×1
Chill Factor III ×1 Screw driver ×1
15
AMD Washer (big) ×4
Mounting Plate ×1
Metal Back Plate ×1
M3 L10 Screw ×5
Anti-Vibration Pad ×4
Anchoring Mount ×1
Screw Nut ×4
Intel Washer (small) ×4M3 L6 Screw ×7
Backplate cap ×1
4 5 76 8
LGA2011 Type B
Screw Pillars x4
Fan Clip ×2
TY-147B ×1 Mylar Film×1

3
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 1 : Backplate Installation
Choose the platform (775/1150/1151/1155/1156/1366) you are in use. Make four M3L10 Screw Pillars
go through the Metal Back Plate and the Mylar lm from bottom towards top.And then place the Metal
Back Plate on the table. Put the four Washers (for Intel) around the Screw Pillars.
Step 2 : 775 Back Plate Cap
Note: When installing on a 775 platform, please rst insert the Back Plate Cap into the opening on
the Back plate, make sure you have the Cap facing downwards. (Only for LGA775 platform, all other
platforms go directly to Step 3.).
Step 3 : Place the motherboard on top of the Back Plate. See the four Screw Pillars go through the four
holes around the processor socket.Cap the four Screw Pillars with the four Screw Nuts.Make sure the
side with a washer is facing the Back Plate.
1366
775
1150
1155
1156
1
2
4
3

The Ultimate Cooling Solutions!
www.thermalright.com
4
Step 4: Step 5:
Step 6:
Step 7:
Step 8:
Step 9:
Step 8: Fan Installation
Put the fan clips into the dents on two sides of the
heat-sink body and make the two ends of the fan
clip go through holes on ange the TY-147B fan.
Step 5 : Apply the thermal paste
Apply the thermal paste to the base of the
Heatsink and the surface of the CPU evenly. (A
flat edge, like a business card or an old credit
card would be benecial in spreading the thermal
paste.)
Step 9 : Installation completed
Plug in the fan connector to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 6: Padding and Mounting Plate Installation
Apply Anti-Vibration padding to 4 corners on the
heat-sink.Place the Heatsink Body on top of the
CPU. Make Mounting Plate go through the Heatsink
Body. And then use the two M3L6 screws to secure
the Mounting Plate, one side at a time in several
turns to ensure balanced mounting.
Step 7: Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body,
for easier access to the
M3L6 Screw underneath
the cooler.
1
2
4
3
Step 4 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw
Nuts. Use the four M3L6 Screws to fix the
Anchoring Mount on to the Screw Nuts.

5
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
Fan Clip
TY-147B
Mounting Plate
Anchoring Mount
LGA2011 Type B Screw Pillars
Anti-Vibration Pads
Heatsink Body
M3L6 Screw
Motherboard
Intel 2011/2011-3

Component
1
1
2
2
3
3
4 5 6
7 8
9
9
10
13
16 17
16 1715
11
14
12
12
14
13
1110
Screw driver ×1
15
AMD Washer (big) ×4
Mounting Plate ×1
Metal Back Plate ×1
M3 L10 Screw ×5
Anti-Vibration Pad ×4
Anchoring Mount ×1
Screw Nut ×4
Intel Washer (small) ×4M3 L6 Screw ×7
Backplate cap ×1
4 5 76 8
LGA2011 Type B
Screw Pillars x4
Fan Clip ×2
TY-147B ×1 Mylar Film×1
Le GRAND MACHO
Heatsink Body ×1
Chill Factor III ×1

7
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 1 : Screw Pillar Installation
Place the motherboard (the processor installed) on top of the desk or a workbench. Fix the four included
LGA2011 Type B Screw Pillars into the heat-sink studs on the Intel ILM Assembly Frame around the
processor socket in a criss-cross pattern.
Step 2: Anchoring Mount Installation
Place the Anchoring Mount on the Screw Pillars. Use the four M3L6 Screws to x the Anchoring Mount
on to the Screw Pillars, also in a criss-cross pattern to ensure balanced mounting.
1
1
2
2
4
4
3
3
Step 3 : Apply the thermal paste
Apply the thermal paste to the base of the Heatsink and the surface of the CPU evenly. (A at edge,
like a business card or an old credit card would be benecial in spreading the thermal paste.)

Le GRAND MACHO
The Ultimate Cooling Solutions!
www.thermalright.com
8
Step 4:
Step 6: Step 7:
Step 5:
Step 6 : Fan Installation
Put the fan clips into the dents on two sides of the
heat-sink body and make the two ends of the fan
clip go through holes on ange the TY-147B fan.
Step 7: Installation completed
Plug in the fan connector to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 4: Padding and Mounting Plate Installation
Apply Anti-Vibration padding to 4 corners on the
heat-sink.
Place the Heatsink Body on top of the CPU. Make
Mounting Plate go through the Heatsink Body.
And then use the two M3L6 screws to secure the
Mounting Plate, one side at a time in several turns
to ensure balanced mounting.
Step 5: Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body,
for easier access to the
M3L6 Screw underneath
the cooler.

9
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
AM2/AM2+/AM3/AM3+/FM1
Fan Clip
TY-147B
Screw Nut
Anti-Vibration Pads
Mounting Plate
Anchoring Mount
AMD Washer (big)
Back Plate Cap
Heatsink Body
M3L6 Screw
Metal Back Plate
Motherboard
M3L10 Screw
Mylar Film

Component
1
1
2
2
3
3
4 5 6
7 8
9
9
10
13
16 17
16 1715
11
14
12
12
14
13
1110
Screw driver ×1
15
AMD Washer (big) ×4
Mounting Plate ×1
Metal Back Plate ×1
M3 L10 Screw ×5
Anti-Vibration Pad ×4
Anchoring Mount ×1
Screw Nut ×4
Intel Washer (small) ×4M3 L6 Screw ×7
Backplate cap ×1
4 5 76 8
LGA2011 Type B
Screw Pillars x4
Fan Clip ×2
TY-147B ×1 Mylar Film×1
Le GRAND MACHO
Heatsink Body ×1
Chill Factor III ×1

11
Installation Instructions:
Step 1:
Step 2:
Step 3:
AMD
Step 1 : Backplate Installation
Choose the platform (AMD) you are in use. Make four M3L10 Screw Pillars go through the Metal Back
Plate and the Mylar lm from bottom towards top. And then place the Metal Back Plate on the table. Put
the four Washers (for AMD) around the Screw Pillars.
Step 2 : Back Plate Cap
Note: When installing on an AMD platform, please rst insert the Back Plate Cap into the opening on the
Metal Back plate, make sure you have the Cap facing downwards.
Step 3 : Place the motherboard on top of the Back Plate. See the four Screw Pillars go through the four
holes around the processor socket. Cap the four Screw Pillars with the four Screw Nuts in a criss-cross
pattern.Make sure the side with a washer is facing the Back Plate.
1
2
3
4

The Ultimate Cooling Solutions!
www.thermalright.com
12
Step 4:
Step 6:
Step 8:
Step 9:
Step 5:
Step 7:
Step 4: Anchoring Mount Installation
Place the Anchoring Mount on the Screw Nuts.
Use the four M3L6 Screws to fix the Anchoring
Mount on to the Screw Nuts.
Step 8 : Fan Installation
Put the fan clips into the dents on two sides of the
heat-sink body and make the two ends of the fan
clip go through holes on ange the TY-147B fan.
Step 5 : Applying Thermal Paste
Apply the Thermal Paste to the base of the
Heatsink and the surface of the CPU evenly. (A
flat edge, like a business card or an old credit
card would be benecial in spreading the thermal
paste.)
Step 9 : Installation completed
Plug in the fan connector to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 6: Padding and Mounting Plate Installation
Apply Anti-Vibration padding to 4 corners on
the heat-sink.Place the Heatsink Body on top
of the CPU. Make Mounting Plate go through
the Heatsink Body. And then use the two M3L6
screws to secure the Mounting Plate, one side
at a time in several turns to ensure balanced
mounting.
Step 7: Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body,
for easier access to the
M3L6 Screw underneath
the cooler.
1
2
4
3

13
Technical Spec
Heatsink Specifications:
Dimension: Length 150mm x Width 120 x Height 159
Weight: 960g
Heatpipe: 6mm heatpipe*7units
Copper Base: C1100 Pure copper nickel plated
Fan Specification:
Dimension: L152mm x H140mm x W26.5m
Weight: 160g
Fan speed: 300~1300RPM (4-Pin PWM)
Fan noise: 14~20dBA MAX (4-Pin PWM)
Airflow: 16.9~73.6CFM MAX
Connector: 4 Pin (PWM Fan connector)

The Ultimate Cooling Solutions!
www.thermalright.com

The Ultimate Cooling Solutions!
www.thermalright.com
TEL: +886-2-2915-5005
FAX: +886-2-2915-5123
EMAIL: sales@thermalright.com