Thermal Arc 95S Thermal Arc Operating Manual

Download

95 S

THERMAL ARC

INVERTER ARC WELDER

Operating

Art # A-08597_AB

Manual

Revision: AB Issue Date: March 26, 2009 Manual No.: 0-5086 Operating Features:

WE APPRECIATE YOUR BUSINESS!

Congratulations on your new Thermal Arc product. We are proud to have you as our customer and will strive to provide you with the best service and reliability in the industry. This product is backed by our extensive warranty and world-wide service network. To locate your nearest distributor or service agency call 1-800-752-7621, or visit us on the web at www.Thermalarc.com.

This Operating Manual has been designed to instruct you on the correct use and operation of your Thermal Arc product. Your satisfaction with this product and its safe operation is our ultimate concern. Therefore please take the time to read the entire manual, especially the Safety Precautions. They will help you to avoid potential hazards that may exist when working with this product.

YOU ARE IN GOOD COMPANY!

The Brand of Choice for Contractors and Fabricators Worldwide.

Thermal Arc is a Global Brand of Arc Welding Products for Thermadyne Industries Inc. We manufacture and supply to major welding industry sectors worldwide including; Manufacturing, Construction, Mining, Automotive, Aerospace, Engineering, Rural and DIY/Hobbyist.

We distinguish ourselves from our competition through marketleading, dependable products that have stood the test of time. We pride ourselves on technical innovation, competitive prices, excellent delivery, superior customer service and technical support, together with excellence in sales and marketing expertise.

Above all, we are committed to develop technologically advanced products to achieve a safer working environment within the welding industry.

WARNINGS

Read and understand this entire Manual and your employer’s safety practices before installing, operating, or servicing the equipment.

While the information contained in this Manual represents the Manufacturer’s best judgement, the Manufacturer assumes no liability for its use.

Operating Manual Number 0-5086 for: Thermal Arc 95 S Power Source Arc Welder Part No. W1003200 Thermal Arc 95 S System with Stick Kit & Case Part No. W1003202 Thermal Arc 95 S System with Stick/TIG Kit & Case Part No. W1003203

Published by: Thermadyne Industries Inc. 82 Benning Street West Lebanon, New Hampshire, USA 03784 (603) 298-5711

www.thermalarc.com

Reproduction of this work, in whole or in part, without written permission of the publisher is prohibited.

The publisher does not assume and hereby disclaims any liability to any party for any loss or damage caused by any error or omission in this Manual, whether such error results from negligence, accident, or any other cause.

Publication Date: March 26, 2009

Record the following information for Warranty purposes:

Where Purchased: ____________________________________

Purchase Date: ____________________________________

Equipment Serial #: ____________________________________

2009 by

TABLE OF CONTENTS

SECTION 1:SAFETY INSTRUCTIONS AND WARNINGS ................................................ 1-1

1.01 Arc Welding Hazards ....................................................................................... 1-1

1.02 Principal Safety Standards .............................................................................. 1-4

1.03 Symbol Chart .................................................................................................. 1-5

1.04 Precautions De Securite En Soudage A L’arc .................................................. 1-6

1.05 Dangers relatifs au soudage à l’arc ................................................................. 1-6

1.06 Principales Normes De Securite ..................................................................... 1-9

1.07 Graphique de Symbole .................................................................................. 1-10

SECTION 2:INTRODUCTION ............................................................................... 2-1

2.01 How to Use This Manual ................................................................................. 2-1

2.02 Equipment Identiﬁcation ................................................................................. 2-1

2.03 Receipt of Equipment ...................................................................................... 2-1

2.04 Description ..................................................................................................... 2-1

2.05 Transportation Methods .................................................................................. 2-1

2.06 Duty Cycle ....................................................................................................... 2-1

2.07 Speciﬁcations ................................................................................................. 2-2

SECTION 3:INSTALLATION ................................................................................ 3-1

3.01 Environment ................................................................................................... 3-1

3.02 Location .......................................................................................................... 3-1

3.03 Electrical Input Connections ........................................................................... 3-1

3.04 Electromagnetic Compatibility ........................................................................ 3-4

3.05 Setup for Welding ........................................................................................... 3-5

3.06 STICK (SMAW) Setup ..................................................................................... 3-6

3.07 Lift TIG (GTAW) Setup .................................................................................... 3-7

SECTION 4:OPERATION .................................................................................... 4-1

4.01 Front Panel ..................................................................................................... 4-1

4.02 SMAW Electrode Polarity ................................................................................ 4-2

4.03 Effects of Stick Welding Various Materials ...................................................... 4-2

4.04 GTAW Electrode Polarity ................................................................................. 4-3

4.05 Guide for Selecting Filler Wire ........................................................................ 4-3

4.06 Tungsten Electrode Current Ranges ................................................................ 4-3

4.07 Shielding Gas Selection .................................................................................. 4-3

4.08 Tungsten Electrode Types ............................................................................... 4-3

4.09 TIG Welding Parameters for Steel ................................................................... 4-3

4.10 Arc Welding Practice ....................................................................................... 4-4

4.11 Welding Position ............................................................................................. 4-4

4.12 Joint Preparations ........................................................................................... 4-5

4.13 Arc Welding Technique ................................................................................... 4-6

4.14 The Welder ...................................................................................................... 4-6

4.15 Striking the Arc ............................................................................................... 4-6

4.16 Arc Length ...................................................................................................... 4-6

4.17 Rate of Travel .................................................................................................. 4-6

4.18 Making Welded Joints ..................................................................................... 4-6

4.19 Distortion ........................................................................................................ 4-8

4.20 The Cause of Distortion .................................................................................. 4-9

4.21 Overcoming Distortion Effects ........................................................................ 4-9

TABLE OF CONTENTS

SECTION 5:SERVICE ....................................................................................... 5-1

5.01 Maintenance and Inspection ........................................................................... 5-1

5.02 STICK Welding Problems ............................................................................... 5-2

5.03 TIG Welding Problems ................................................................................... 5-3

5.04 Power Source Problems ................................................................................ 5-4

APPENDIX 1: REPLACEMENT PARTS .................................................................... A-1

APPENDIX 2: OPTIONS AND ACCESSORIES ............................................................ A-2

APPENDIX 3: system schematic ......................................................................... A-3

LIMITED WARRANTY

WARRANTY SCHEDULE

GLOBAL CUSTOMER SERVICE CONTACT INFORMATION ................................... Inside Rear

SAFETY INSTRUCTIONS THERMAL ARC 95 S

SECTION 1:

SAFETY INSTRUCTIONS AND WARNINGS

WARNING

PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS KEEP AWAY UNTIL CONSULTING YOUR DOCTOR. DO NOT LOSE THESE INSTRUCTIONS. READ OPERATING/INSTRUCTION MANUAL BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT.

Welding products and welding processes can cause serious injury or death, or damage to other equipment or property, if the operator does not strictly observe all safety rules and take precautionary actions.

Safe practices have developed from past experience in the use of welding and cutting. These practices must be learned through study and training before using this equipment. Some of these practices apply to equipment connected to power lines; other practices apply to engine driven equipment. Anyone not having extensive training in welding and cutting practices should not attempt to weld.

Safe practices are outlined in the American National Standard Z49.1 entitled: SAFETY IN WELDING AND CUTTING. This publication and other guides to what you should learn before operating this equipment are listed at the end of these safety precautions. HAVE ALL INSTALLATION,

OPERATION, MAINTENANCE, AND REPAIR WORK PERFORMED ONLY BY QUALIFIED PEOPLE.

1.01 Arc Welding Hazards

WARNING

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks or severe burns. The electrode and work circuit is electrically live whenever the output is on. The input power circuit and machine internal circuits are also live when power is on. In semi-automatic or automatic wire welding, the wire, wire reel, drive roll housing, and all metal parts touching the welding wire are electrically live. Incorrectly installed or improperly grounded equipment is a hazard.

1. Do not touch live electrical parts.

2. Wear dry, hole-free insulating gloves and body protection.

3. Insulate yourself from work and ground using dry insulating mats or covers.

4. Disconnect input power or stop engine before installing or servicing this equipment. Lock input power disconnect switch open, or remove line fuses so power cannot be turned on accidentally.

5. Properly install and ground this equipment according to its Owner’s Manual and national, state, and local codes.

6. Turn off all equipment when not in use. Disconnect power to equipment if it will be left unattended or out of service.

7. Use fully insulated electrode holders. Never dip holder in water to cool it or lay it down on the ground or the work surface. Do not touch holders connected to two welding machines at the same time or touch other people with the holder or electrode.

8. Do not use worn, damaged, undersized, or poorly spliced cables.

9. Do not wrap cables around your body.

10. Ground the workpiece to a good electrical (earth) ground.

11. Do not touch electrode while in contact with the work (ground) circuit.

12. Use only well-maintained equipment. Repair or replace damaged parts at once.

13. In conﬁned spaces or damp locations, do not use a welder with AC output unless it is equipped with a voltage reducer. Use equipment with DC output.

14. Wear a safety harness to prevent falling if working above ﬂoor level.

15. Keep all panels and covers securely in place.

WARNING

ARC RAYS can burn eyes and skin; NOISE can damage hearing. Arc rays from the welding process produce intense heat and strong ultraviolet rays that can burn eyes and skin. Noise from some processes can damage hearing.

1. Wear a welding helmet ﬁtted with a proper shade of ﬁlter (see ANSI Z49.1 listed in Safety Standards) to protect your face and eyes when welding or watching.

2. Wear approved safety glasses. Side shields recommended.

3. Use protective screens or barriers to protect others from ﬂash and glare; warn others not to watch the arc.

4. Wear protective clothing made from durable, ﬂame-resistant material (wool and leather) and foot protection.

Safety Instructions 1-1 Manual 0-5086

5. Use approved ear plugs or ear muffs if noise level is high.

THERMAL ARC 95 S SAFETY INSTRUCTIONS

Welding or Cutting

Operation

Electrode Siz

Metal Thickness

or Weldin

Current

Filter

Shade

No.

Welding or Cutting

Operation

Electrode Siz

Metal Thickness

or Weldin

Filter

Shade

No.

Torch soldering 2

Gas metal-arc welding (MIG)

Torch brazing 3 or 4 Non-ferrous base metal All 11

Oxygen Cutting

Non-ferrous base metal All 12

Light Under 1 in., 25 mm 3 or 4 Gas tungsten arc welding All 12

Medium 1 to 6 in., 25-150 mm 4 or 5 (TIG) All 12

Heavy Over 6 in., 150 mm 5 or 6 Atomic hydrogen welding All 12

Gas welding

Carbon arc welding All 12

Light Under 1/8 in., 3 mm 4 or 5 Plasma arc welding

Medium 1/8 to 1/2 in., 3-12 mm 5 or 6

Carbon arc air gouging

Heavy Over 1/2 in., 12 mm 6 or 8 Light 12

Shielded metal-arc

welding

(stick) electrodes

Under 5/32 in., 4 mm 10 Heavy 14

5/32 to 1/4 in.,

4 to 6.4 mm

Plasma arc cutting

Over 1/4 in., 6.4 mm 14 Light Under 300 Amp 9

Medium 300 to 400 Amp 12

Heavy Over 400 Amp 14

Eye protection filter shade selector for welding or cutting

(goggles or helmet), from AWS A6.2-73.

WARNING

FUMES AND GASES can be hazardous to your health.

Welding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health.

1. Keep your head out of the fumes. Do not breathe the fumes.

2. If inside, ventilate the area and/or use exhaust at the arc to remove welding fumes and gases.

3. If ventilation is poor, use an approved air-supplied respirator.

4. Read the Material Safety Data Sheets (MSD Ss) and the manufacturer’s instruction for metals, consumables, coatings, and cleaners.

5. Work in a conﬁned space only if it is well ventilated, or while wearing an air-supplied respirator. Shielding gases used for welding can displace air causing injury or death. Be sure the breathing air is safe.

6. Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form highly toxic and irritating gases.

7. Do not weld on coated metals, such as galvanized, lead, or cadmium plated steel, unless the coating is removed from the weld area, the area is well ventilated, and if necessary, while wearing an air-supplied respirator. The coatings and any metals containing these elements can give off toxic fumes if welded.

WARNING

WELDING can cause ﬁre or explosion.

Sparks and spatter ﬂy off from the welding arc. The ﬂying sparks and hot metal, weld spatter, hot workpiece, and hot equipment can cause ﬁres and burns. Accidental contact of electrode or welding wire to metal objects can cause sparks, overheating, or ﬁre.

1. Protect yourself and others from ﬂying sparks and hot metal.

2. Do not weld where ﬂying sparks can strike ﬂammable material.

3. Remove all ﬂammables within 35 ft (10.7 m) of the welding arc. If this is not possible, tightly cover them with approved covers.

4. Be alert that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas.

5. Watch for ﬁre, and keep a ﬁre extinguisher nearby.

6. Be aware that welding on a ceiling, ﬂoor, bulkhead, or partition can cause ﬁre on the hidden side.

7. Do not weld on closed containers such as tanks or drums.

8. Connect work cable to the work as close to the welding area as practical to prevent welding current from traveling long, possibly unknown paths and causing electric shock and ﬁre hazards.

9. Do not use welder to thaw frozen pipes.

10. Remove stick electrode from holder or cut off welding wire at contact tip when not in use.

Manual 0-5086 1-2 Safety Instructinos

SAFETY INSTRUCTIONS THERMAL ARC 95 S

WARNING

FLYING SPARKS AND HOT METAL can cause injury.

Chipping and grinding cause ﬂying metal. As welds cool, they can throw off slag.

1. Wear approved face shield or safety goggles. Side shields recommended.

2. Wear proper body protection to protect skin.

WARNING

CYLINDERS can explode if damaged.

Shielding gas cylinders contain gas under high pressure. If damaged, a cylinder can explode. Since gas cylinders are normally part of the welding process, be sure to treat them carefully.

1. Protect compressed gas cylinders from excessive heat, mechanical shocks, and arcs.

2. Install and secure cylinders in an upright position by chaining them to a stationary support or equipment cylinder rack to prevent falling or tipping.

3. Keep cylinders away from any welding or other electrical circuits.

4. Never allow a welding electrode to touch any cylinder.

5. Use only correct shielding gas cylinders, regulators, hoses, and ﬁttings designed for the speciﬁc application; maintain them and associated parts in good condition.

6. Turn face away from valve outlet when opening cylinder valve.

7. Keep protective cap in place over valve except when cylinder is in use or connected for use.

8. Read and follow instructions on compressed gas cylinders, associated equipment, and CGA publication P-1 listed in Safety Standards.

WARNING

ENGINE FUEL can cause ﬁre or explosion.

Engine fuel is highly ﬂammable.

1. Stop engine before checking or adding fuel.

2. Do not add fuel while smoking or if unit is near any sparks or open ﬂames.

3. Allow engine to cool before fueling. If possible, check and add fuel to cold engine before beginning job.

4. Do not overﬁll tank — allow room for fuel to expand.

5. Do not spill fuel. If fuel is spilled, clean up before starting engine.

WARNING

MOVING PARTS can cause injury.

Moving parts, such as fans, rotors, and belts can cut ﬁngers and hands and catch loose clothing.

1. Keep all doors, panels, covers, and guards closed and securely in place.

2. Stop engine before installing or connecting unit.

3. Have only qualiﬁed people remove guards or covers for maintenance and troubleshooting as necessary.

4. To prevent accidental starting during servicing, disconnect negative (-) battery cable from battery.

5. Keep hands, hair, loose clothing, and tools away from moving parts.

6. Reinstall panels or guards and close doors when servicing is ﬁnished and before starting engine.

WARNING

Engines can be dangerous.

WARNING

ENGINE EXHAUST GASES can kill.

Engines produce harmful exhaust gases.

1. Use equipment outside in open, well-ventilated areas.

2. If used in a closed area, vent engine exhaust outside and away from any building air intakes.

Safety Instructions 1-3 Manual 0-5086

SPARKS can cause BATTERY GASES TO EXPLODE; BATTERY ACID can burn eyes and skin.

Batteries contain acid and generate explosive gases.

1. Always wear a face shield when working on a battery.

2. Stop engine before disconnecting or connecting battery cables.

3. Do not allow tools to cause sparks when working on a battery.

4. Do not use welder to charge batteries or jump start vehicles.

5. Observe correct polarity (+ and –) on batteries.

THERMAL ARC 95 S SAFETY INSTRUCTIONS

WARNING

STEAM AND PRESSURIZED HOT COOLANT can burn face, eyes, and skin.

The coolant in the radiator can be very hot and under pressure.

1. Do not remove radiator cap when engine is hot. Allow engine to cool.

2. Wear gloves and put a rag over cap area when removing cap.

3. Allow pressure to escape before completely removing cap.

This product contains chemicals, including lead, or otherwise produces chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Wash hands after handling. (California Health & Safety Code § 25249.5 et seq.)

Considerations About Welding And The Effects of Low Frequency Electric and Magnetic Fields

The following is a quotation from the General Conclusions Section of the U.S. Congress, Ofﬁce of Technology Assessment, Biological Effects of Power Frequency Electric & Magnetic Fields - Background Paper, OTA-BP-E-63 (Washington, DC: U.S. Government Printing Ofﬁce, May

1989): “...there is now a very large volume of scientiﬁc ﬁndings based

on experiments at the cellular level and from studies with animals and people which clearly establish that low frequency magnetic ﬁelds interact with, and produce changes in, biological systems. While most of this work is of very high quality, the results are complex. Current scientiﬁc understanding does not yet allow us to interpret the evidence in a single coherent framework. Even more frustrating, it does not yet allow us to draw deﬁnite conclusions about questions of possible risk or to offer clear science-based advice on strategies to minimize or avoid potential risks.”

LEAD WARNING

NOTE

ABOUT PACEMAKERS:

The above procedures are among those also normally recommended for pacemaker wearers. Consult your doctor for complete information.

1.02 Principal Safety Standards

Safety in Welding and Cutting, ANSI Standard Z49.1, from American Welding Society, 550 N.W. LeJeune Rd., Miami, FL 33126.

Safety and Health Standards, OSHA 29 CFR 1910, from Superintendent of Documents, U.S. Government Printing Ofﬁce, Washington, D.C.

20402.

Recommended Safe Practices for the Preparation for Welding and Cutting of Containers That Have Held Hazardous Substances, American Welding Society Standard AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd., Miami, FL 33126.

National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, from Compressed Gas Association, 1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202.

Code for Safety in Welding and Cutting, CSA Standard W117.2, from Canadian Standards Association, Standards Sales, 178 Rexdale Boulevard, Rexdale, Ontario, Canada M9W 1R3.

Safe Practices for Occupation and Educational Eye and Face Protection, ANSI Standard Z87.1, from American National Standards Institute, 1430 Broadway, New York, NY 10018.

Cutting and Welding Processes, NFPA Standard 51B, from National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

To reduce magnetic fields in the workplace, use the following procedures.

1. Keep cables close together by twisting or taping them.

2. Arrange cables to one side and away from the operator.

3. Do not coil or drape cable around the body.

4. Keep welding power source and cables as far away from body as practical.

Manual 0-5086 1-4 Safety Instructinos

SAFETY INSTRUCTIONS THERMAL ARC 95 S

Gas Tungsten Arc Welding (GTAW)

Air Carbon Arc Cutting (CAC-A)

Constant Current

Constant Voltage Or Constant Potential

High Temperature

Fault Indication

Arc Force

Touch Start (GTAW)

Variable Inductance

Voltage Input

Single Phase

Three Phase

Three Phase Static Frequency ConverterTransformer-Rectifier

Dangerous Voltage

Off

Panel/Local

Shielded Metal Arc Welding (SMAW)

Gas Metal Arc Welding (GMAW)

Increase/Decrease

Circuit Breaker

AC Auxiliary Power

Remote

Duty Cycle

Percentage

Amperage

Voltage

Hertz (cycles/sec)

Frequency

Negative

Positive

Direct Current (DC)

Protective Earth (Ground)

Line

Line Connection

Auxiliary Power

Receptacle RatingAuxiliary Power

Art # A-04130

115V 15A

IPM

MPM

Fuse

Wire Feed Function

Wire Feed Towards Workpiece With Output Voltage Off.

Preflow Time

Postflow Time

Spot Time

Spot Weld Mode

Continuous Weld Mode

Press to initiate wirefeed and welding, release to stop.

Purging Of Gas

Inches Per Minute

Meters Per Minute

Welding Gun

Burnback Time

Press and hold for preflow, release to start arc. Press to stop arc, and hold for preflow.

4 Step Trigger Operation

2 Step Trigger Operation

1.03 Symbol Chart

Note that only some of these symbols will appear on your model.

Safety Instructions 1-5 Manual 0-5086

THERMAL ARC 95 S SAFETY INSTRUCTIONS

1.04 Precautions De Securite En Soudage A L’arc

MISE EN GARDE

LE SOUDAGE A L’ARC EST DANGEREUX

PROTEGEZ-VOUS, AINSI QUE LES AUTRES, CONTRE LES BLESSURES GRAVES POSSIBLES OU LA MORT. NE LAISSEZ PAS LES ENFANTS S’APPROCHER, NI LES PORTEURS DE STIMULATEUR CARDIAQUE (A MOINS QU’ILS N’AIENT CONSULTE UN MEDECIN). CONSERVEZ CES INSTRUCTIONS. LISEZ LE MANUEL D’OPERATION OU LES INSTRUCTIONS AVANT D’INSTALLER, UTILISER OU ENTRETENIR CET EQUIPEMENT.

Les produits et procédés de soudage peuvent sauser des blessures graves ou la mort, de même que des dommages au reste du matériel et à la propriété, si l’utilisateur n’adhère pas strictement à toutes les règles de sécurité et ne prend pas les précautions nécessaires.

En soudage et coupage, des pratiques sécuritaires se sont développées suite à l’expérience passée. Ces pratiques doivent être apprises par étude ou entraînement avant d’utiliser l’equipement. Toute personne n’ayant pas suivi un entraînement intensif en soudage et coupage ne devrait pas tenter de souder. Certaines pratiques concernent les équipements raccordés aux lignes d’alimentation alors que d’autres s’adressent aux groupes électrogènes.

La norme Z49.1 de l’American National Standard, intitulée “SAFETY IN WELDING AND CUTTING” présente les pratiques sécuritaires à suivre. Ce document ainsi que d’autres guides que vous devriez connaître avant d’utiliser cet équipement sont présentés à la ﬁn de ces instructions de sécurité.

SEULES DES PERSONNES QUALIFIEES DOIVENT FAIRE DES TRAVAUX D’INSTALLATION, DE REPARATION, D’ENTRETIEN ET D’ESSAI.

1.05 Dangers relatifs au soudage à l’arc

AVERTISSEMENT

L’ELECTROCUTION PEUT ETRE MORTELLE.

Une décharge électrique peut tuer ou brûler gravement. L’électrode et le circuit de soudage sont sous tension dès la mise en circuit. Le circuit d’alimentation et les circuits internes de l’équipement sont aussi sous tension dès la mise en marche. En soudage automatique ou semi-automatique avec ﬁl, ce dernier, le rouleau ou la bobine de ﬁl, le logement des galets d’entrainement et toutes les pièces métalliques en contact avec le ﬁl de soudage sont sous tension. Un équipement inadéquatement installé ou inadéquatement mis à la terre est dangereux.

1. Ne touchez pas à des pièces sous tension.

2. Portez des gants et des vêtements isolants, secs et non troués.

3 Isolez-vous de la pièce à souder et de la mise à la terre au moyen

de tapis isolants ou autres.

4. Déconnectez la prise d’alimentation de l’équipement ou arrêtez le moteur avant de l’installer ou d’en faire l’entretien. Bloquez le commutateur en circuit ouvert ou enlevez les fusibles de l’alimentation aﬁn d’éviter une mise en marche accidentelle.

7. N’utilisez que des porte-électrodes bien isolés. Ne jamais plonger les porte-électrodes dans l’eau pour les refroidir. Ne jamais les laisser traîner par terre ou sur les pièces à souder. Ne touchez pas aux porte-électrodes raccordés à deux sources de courant en même temps. Ne jamais toucher quelqu’un d’autre avec l’électrode ou le porte-électrode.

8. N’utilisez pas de câbles électriques usés, endommagés, mal épissés ou de section trop petite.

9. N’enroulez pas de câbles électriques autour de votre corps.

10. N’utilisez qu’une bonne prise de masse pour la mise à la terre de la pièce à souder.

11. Ne touchez pas à l’électrode lorsqu’en contact avec le circuit de soudage (terre).

12. N’utilisez que des équipements en bon état. Réparez ou remplacez aussitôt les pièces endommagées.

13. Dans des espaces conﬁnés ou mouillés, n’utilisez pas de source de courant alternatif, à moins qu’il soit muni d’un réducteur de tension. Utilisez plutôt une source de courant continu.

14. Portez un harnais de sécurité si vous travaillez en hauteur.

15. Fermez solidement tous les panneaux et les capots.

AVERTISSEMENT

5. Veuillez à installer cet équipement et à le mettre à la terre selon le manuel d’utilisation et les codes nationaux, provinciaux et locaux applicables.

6. Arrêtez tout équipement après usage. Coupez l’alimentation de l’équipement s’il est hors d’usage ou inutilisé.

Manual 0-5086 1-6 Safety Instructinos

LE RAYONNEMENT DE L’ARC PEUT BRÛLER LES YEUX ET LA PEAU; LE BRUIT PEUT ENDOMMAGER L’OUIE.

L’arc de soudage produit une chaleur et des rayons ultraviolets intenses, susceptibles de brûler les yeux et la peau. Le bruit causé par certains procédés peut endommager l’ouïe.

SAFETY INSTRUCTIONS THERMAL ARC 95 S

1. Portez une casque de soudeur avec ﬁltre oculaire de nuance appropriée (consultez la norme ANSI Z49 indiquée ci-après) pour vous protéger le visage et les yeux lorsque vous soudez ou que vous observez l’exécution d’une soudure.

2. Portez des lunettes de sécurité approuvées. Des écrans latéraux sont recommandés.

3. Entourez l’aire de soudage de rideaux ou de cloisons pour protéger les autres des coups d’arc ou de l’éblouissement; avertissez les observateurs de ne pas regarder l’arc.

4. Portez des vêtements en matériaux ignifuges et durables (laine et cuir) et des chaussures de sécurité.

5. Portez un casque antibruit ou des bouchons d’oreille approuvés lorsque le niveau de bruit est élevé.

AVERTISSEMENT

LES VAPEURS ET LES FUMEES SONT DANGEREUSES POUR LA SANTE.

Le soudage dégage des vapeurs et des fumées dangereuses à respirer.

1. Eloignez la tête des fumées pour éviter de les respirer.

2. A l’intérieur, assurez-vous que l’aire de soudage est bien ventilée ou que les fumées et les vapeurs sont aspirées à l’arc.

3. Si la ventilation est inadequate, portez un respirateur à adduction d’air approuvé.

4. Lisez les ﬁches signalétiques et les consignes du fabricant relatives aux métaux, aux produits consummables, aux revêtements et aux produits nettoyants.

5. Ne travaillez dans un espace conﬁné que s’il est bien ventilé; sinon, portez un respirateur à adduction d’air. Les gaz protecteurs de soudage peuvent déplacer l’oxygène de l’air et ainsi causer des malaises ou la mort. Assurez-vous que l’air est propre à la respiration.

6. Ne soudez pas à proximité d’opérations de dégraissage, de nettoyage ou de pulvérisation. La chaleur et les rayons de l’arc peuvent réagir avec des vapeurs et former des gaz hautement toxiques et irritants.

7. Ne soudez des tôles galvanisées ou plaquées au plomb ou au cadmium que si les zones à souder ont été grattées à fond, que si l’espace est bien ventilé; si nécessaire portez un respirateur à adduction d’air. Car ces revêtements et tout métal qui contient ces éléments peuvent dégager des fumées toxiques au moment du soudage.

SELECTION DES NUANCES DE FILTRES OCULAIRS POUR LA PROTECTION

DES YEUX EN COUPAGE ET SOUDAGE (selon AWS á 8.2-73)

Opération de coupage

ou soudage

Brassage tendre au chalumeau

Brassage fort au chalumeau

Oxycoupage métaux ferreux toutes conditions 12

mince moins de 1 po. (25 mm) 2 ou 3

moyen de 1 á 6 po. (25 á 150 mm) 4 ou 5

épais plus de 6 po. (150 mm) 5 ou 6

Soudage aux gaz Soudage á l'arc Plasma (PAW) toutes dimensions 12

mince moins de 1/8 po. (3 mm) 4 ou 5

moyen de 1/8 á 1/2 po. (3 á 12 mm) 5 ou 6 mince 12

épais plus de 1/2 po. (12 mm) 6 ou 8 épais 14

Soudage á l'arc avec électrode enrobees (SMAW)

Dimension d'électrode ou

Epiasseur de métal ou

Intensité de courant

toutes conditions 2

toutes conditions 3 ou 4 métaux non-ferreux toutes conditions 11

moins de 5/32 po. (4 mm) 10 Coupage á l'arc Plasma (PAC)

5/32 á 1/4 po. (4 á 6.4 mm) 12 mince moins de 300 amperès 9

plus de 1/4 po. (6.4 mm) 14 moyen de 300 á 400 amperès 12

Nuance de

ﬁltre oculaire

Opération de coupage

ou soudage

Soudage á l'arc sous gaz avec ﬁl plein (GMAW)

Soudage á l'arc sous gaz avec électrode de tungstène (GTAW)

Soudage á l'hydrogène atomique (AHW)

Soudage á l'arc avec électrode de carbone (CAW)

Gougeage Air-Arc avec électrode de carbone

Dimension d'électrode ou

Epiasseur de métal ou

Intensité de courant

toutes conditions 12

épais plus de 400 amperès 14

Nuance de

ﬁltre

oculaire

Safety Instructions 1-7 Manual 0-5086

THERMAL ARC 95 S SAFETY INSTRUCTIONS

AVERTISSEMENT

LE SOUDAGE PEUT CAUSER UN INCENDIE OU UNE EXPLOSION

L’arc produit des étincellies et des projections. Les particules volantes, le métal chaud, les projections de soudure et l’équipement surchauffé peuvent causer un incendie et des brûlures. Le contact accidentel de l’électrode ou du ﬁl-électrode avec un objet métallique peut provoquer des étincelles, un échauffement ou un incendie.

1. Protégez-vous, ainsi que les autres, contre les étincelles et du métal chaud.

2. Ne soudez pas dans un endroit où des particules volantes ou des projections peuvent atteindre des matériaux inﬂammables.

3. Enlevez toutes matières inﬂammables dans un rayon de 10, 7 mètres autour de l’arc, ou couvrez-les soigneusement avec des bâches approuvées.

4. Méﬁez-vous des projections brulantes de soudage susceptibles de pénétrer dans des aires adjacentes par de petites ouvertures ou ﬁssures.

5. Méﬁez-vous des incendies et gardez un extincteur à portée de la main.

6. N’oubliez pas qu’une soudure réalisée sur un plafond, un plancher, une cloison ou une paroi peut enﬂammer l’autre côté.

7. Ne soudez pas un récipient fermé, tel un réservoir ou un baril.

8. Connectez le câble de soudage le plus près possible de la zone de soudage pour empêcher le courant de suivre un long parcours inconnu, et prévenir ainsi les risques d’électrocution et d’incendie.

AVERTISSEMENT

LES BOUTEILLES ENDOMMAGEES PEUVENT EXPLOSER

Les bouteilles contiennent des gaz protecteurs sous haute pression. Des bouteilles endommagées peuvent exploser. Comme les bouteilles font normalement partie du procédé de soudage, traitez-les avec soin.

1. Protégez les bouteilles de gaz comprimé contre les sources de chaleur intense, les chocs et les arcs de soudage.

2. Enchainez verticalement les bouteilles à un support ou à un cadre ﬁxe pour les empêcher de tomber ou d’être renversées.

3. Eloignez les bouteilles de tout circuit électrique ou de tout soudage.

4. Empêchez tout contact entre une bouteille et une électrode de soudage.

5. N’utilisez que des bouteilles de gaz protecteur, des détendeurs, des boyauxs et des raccords conçus pour chaque application spéciﬁque; ces équipements et les pièces connexes doivent être maintenus en bon état.

6. Ne placez pas le visage face à l’ouverture du robinet de la bouteille lors de son ouverture.

7. Laissez en place le chapeau de bouteille sauf si en utilisation ou lorsque raccordé pour utilisation.

8. Lisez et respectez les consignes relatives aux bouteilles de gaz comprimé et aux équipements connexes, ainsi que la publication P-1 de la CGA, identiﬁée dans la liste de documents ci-dessous.

9. Ne dégelez pas les tuyaux avec un source de courant.

10. Otez l’électrode du porte-électrode ou coupez le ﬁl au tube-contact lorsqu’inutilisé après le soudage.

11. Portez des vêtements protecteurs non huileux, tels des gants en cuir, une chemise épaisse, un pantalon revers, des bottines de sécurité et un casque.

AVERTISSEMENT

LES ETINCELLES ET LES PROJECTIONS BRULANTES PEUVENT CAUSER DES BLESSURES.

Le piquage et le meulage produisent des particules métalliques volantes. En refroidissant, la soudure peut projeter du éclats de laitier.

1. Portez un écran facial ou des lunettes protectrices approuvées. Des écrans latéraux sont recommandés.

2. Portez des vêtements appropriés pour protéger la peau.

AVERTISSEMENT

LES MOTEURS PEUVENT ETRE DANGEREUX

LES GAZ D’ECHAPPEMENT DES MOTEURS PEUVENT ETRE MORTELS.

Les moteurs produisent des gaz d’échappement nocifs.

1. Utilisez l’équipement à l’extérieur dans des aires ouvertes et bien ventilées.

2. Si vous utilisez ces équipements dans un endroit conﬁné, les fumées d’échappement doivent être envoyées à l’extérieur, loin des prises d’air du bâtiment.

AVERTISSEMENT

LE CARBURANT PEUR CAUSER UN INCENDIE OU UNE EXPLOSION.

Le carburant est hautement inﬂammable.

1. Arrêtez le moteur avant de vériﬁer le niveau e carburant ou de faire le plein.

Manual 0-5086 1-8 Safety Instructinos

SAFETY INSTRUCTIONS THERMAL ARC 95 S

2. Ne faites pas le plein en fumant ou proche d’une source d’étincelles ou d’une ﬂamme nue.

3. Si c’est possible, laissez le moteur refroidir avant de faire le plein de carburant ou d’en vériﬁer le niveau au début du soudage.

4. Ne faites pas le plein de carburant à ras bord: prévoyez de l’espace pour son expansion.

5. Faites attention de ne pas renverser de carburant. Nettoyez tout carburant renversé avant de faire démarrer le moteur.

AVERTISSEMENT

DES PIECES EN MOUVEMENT PEUVENT CAUSER DES BLESSURES.

Des pièces en mouvement, tels des ventilateurs, des rotors et des courroies peuvent couper doigts et mains, ou accrocher des vêtements amples.

1. Assurez-vous que les portes, les panneaux, les capots et les protecteurs soient bien fermés.

2. Avant d’installer ou de connecter un système, arrêtez le moteur.

3. Seules des personnes qualiﬁées doivent démonter des protecteurs ou des capots pour faire l’entretien ou le dépannage nécessaire.

4. Pour empêcher un démarrage accidentel pendant l’entretien, débranchez le câble d’accumulateur à la borne négative.

5. N’approchez pas les mains ou les cheveux de pièces en mouvement; elles peuvent aussi accrocher des vêtements amples et des outils.

6. Réinstallez les capots ou les protecteurs et fermez les portes après des travaux d’entretien et avant de faire démarrer le moteur.

AVERTISSEMENT

LA VAPEUR ET LE LIQUIDE DE REFROIDISSEMENT BRULANT SOUS PRESSION PEUVENT BRULER LA PEAU ET LES YEUX.

Le liquide de refroidissement d’un radiateur peut être brûlant et sous pression.

1. N’ôtez pas le bouchon de radiateur tant que le moteur n’est pas refroidi.

2. Mettez des gants et posez un torchon sur le bouchon pour l’ôter.

3. Laissez la pression s’échapper avant d’ôter complètement le bouchon.

PLOMB AVERTISSEMENT

Ce produit contient des produits chimiques, comme le plomb, ou engendre des produits chimiques, re con nus par l ’état de Ca lif ornie co mme pouvant être à l’origine de cancer, de malformations fœtales ou d’autres problèmes de reproduction. Il faut se laver les mains après toute manipulation. (Code de Californie de la sécurité et santé, paragraphe

25249.5 et suivants)

1.06 Principales Normes De Securite

Safety in Welding and Cutting, norme ANSI Z49.1, American Welding Society, 550 N.W. LeJeune Rd., Miami, FL 33128.

AVERTISSEMENT

DES ETINCELLES PEUVENT FAIRE EXPLOSER UN ACCUMULATEUR; L’ELECTROLYTE D’UN ACCUMU-LATEUR PEUT BRULER LA PEAU ET LES YEUX.

Les accumulateurs contiennent de l’électrolyte acide et dégagent des vapeurs explosives.

1. Portez toujours un écran facial en travaillant sur un accumu-lateur.

2. Arrêtez le moteur avant de connecter ou de déconnecter des câbles d’accumulateur.

3. N’utilisez que des outils anti-étincelles pour travailler sur un accumulateur.

4. N’utilisez pas une source de courant de soudage pour charger un accumulateur ou survolter momentanément un véhicule.

5. Utilisez la polarité correcte (+ et –) de l’accumulateur.

Safety and Health Standards, OSHA 29 CFR 1910, Superintendent of Documents, U.S. Government Printing Ofﬁce, Washington, D.C.

20402.

Recommended Safe Practices for the Preparation for Welding and Cutting of Containers That Have Held Hazardous Substances, norme AWS F4.1, American Welding Society, 550 N.W. LeJeune Rd., Miami, FL 33128.

National Electrical Code, norme 70 NFPA, National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

Safe Handling of Compressed Gases in Cylinders, document P-1, Compressed Gas Association, 1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202.

Code for Safety in Welding and Cutting, norme CSA W117.2 Association canadienne de normalisation, Standards Sales, 276 Rexdale Boulevard, Rexdale, Ontario, Canada M9W 1R3.

Safe Practices for Occupation and Educational Eye and Face Protection, norme ANSI Z87.1, American National Standards Institute, 1430 Broadway, New York, NY 10018.

Cutting and Welding Processes, norme 51B NFPA, National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

Safety Instructions 1-9 Manual 0-5086

THERMAL ARC 95 S SAFETY INSTRUCTIONS

Soudage á L’arc Avec Electrode Non Fusible (GTAW)

Decoupe Arc Carbone (CAC-A)

Courant Constant

Tension Constante Ou Potentiel Constant

Haute Température

Force d'Arc

Amorçage de L’arc au Contact (GTAW)

Inductance Variable

Tension

Mono Phasé

Trois Phasé

Tri-Phase Statique

Fréquence Convertisseur Transformateur-Redresseur

Tension dangereuse

Hors Tension

Sous Tension

Panneau/Local

Soudage Arc Electrique Avec Electrode Enrobé (SMAW)

Soudage á L’arc Avec Fil Electrodes Fusible (GMAW)

Augmentez/Diminuer

Disjoncteur

Source AC Auxiliaire

Distant

Facteur de Marche

Pourcentage

Intensité de Courant

Tension

Hertz (cycles/sec)

Fréquence

Négatif

Positif

Courant Continue (DC)

Terre de Protection

Ligne

Connexion de la Ligne

Source Auxiliaire

Classement de PriseSource Auxiliaire

Art # A-07639

115V 15A

IPM

MPM

Fusible

Déroulement du Fil

Alimentation du Fil Vers la Pièce de Fabrication Hors Tension

Durée de Pré-Dèbit

Durée de Post-Dèbit

Duréc du Pulse

Soudure Par Point

Appuyez pour dèruarer l’alimentation du fils et la soudure, le relâcher pour arrêter.

Purge Du Gaz

Mode Continu de Soudure

Pouces Par Minute

Mètres Par Minute

Torch de

Soudage

Probléme de Terre

Maintenez appuyez pour pré-dèbit, relailez pour initier l'arc. Appuyez pour arrêter l'arc, et mainteuir pour pré-dèbit.

Détente à 4-Temps

Détente à 2-Temps

1.07 Graphique de Symbole

Seulement certains de ces symboles apparaîtront sur votre modèle.

Manual 0-5086 1-10 Safety Instructinos

INTRODUCTION THERMAL ARC 95 S

SECTION 2:

INTRODUCTION

2.01 How to Use This Manual

This Operating Manual usually applies to the part numbers listed on page i. If none are underlined, they are all covered by this manual. To ensure safe operation, read the entire manual, including the chapter on safety instructions and warnings. Throughout this manual, the word WARNING, CAUTION and NOTE may appear. Pay particular attention to the information provided under these headings. These special annotations are easily recognized as follows:

WARNING

Gives information regarding possible personal injury. Warnings will be enclosed in a box such as this.

CAUTION

Refers to possible equipment damage. Cautions will be shown in bold type.

NOTE

Offers helpful information concerning certain operating procedures. Notes will be shown in italics

2.02 Equipment Identiﬁcation

The unit’s identiﬁcation number (speciﬁcation or part number), model, and serial number usually appear on a nameplate attached to the machine. Equipment which does not have a nameplate attached to the machine is identiﬁed only by the speciﬁcation or part number printed on the shipping container. Record these numbers for future reference.

2.03 Receipt of Equipment

When you receive the equipment, check it against the invoice to make sure it is complete and inspect the equipment for possible damage due to shipping. If there is any damage, notify the carrier immediately to ﬁle a claim. Furnish complete information concerning damage claims or shipping errors to the location in your area listed in the inside back cover of this manual. Include all equipment identiﬁcation numbers as described above along with a full description of the parts in error.

2.04 Description

This compact inverter welding machine has inﬁnitely adjustable welding current from 5 to 95 amps. It uses standard general purpose SMAW 3/32” (2.5mm) electrodes for light gauge work, generally less than 1/8” (3.2mm) thick. The unit also has a Lift TIG (GTAW) welding mode that offers stable TIG welding characteristics when used with a suitable TIG torch and shielding gas.

2.05 Transportation Methods

CAUTION

ELECTRIC SHOCK can kill. DO NOT TOUCH live electric parts. Disconnect input power conductors from de-energized supply line before moving the welding power source.

WARNING

FALLING EQUIPMENT can cause serious personal injury and equipment damage.

Lift unit with handle on top of case. Use handcart or similar device of adequate capacity. If using a fork lift vehicle, place secure unit on a proper skid before transporting.

2.06 Duty Cycle

The rated duty cycle of a Welding Power Source, is a statement of the time it may be operated at its rated welding current output without exceeding the temperature limits of the insulation of the component parts. To explain the 10 minute duty cycle period the following example is used. Suppose a Welding Power Source is designed to operate at a 30% duty cycle, 80 amperes at 23.2 volts. This means that it has been designed and built to provide the rated amperage (80A) for 3 minutes, i.e. arc welding time, out of every 10 minute period (30% of 10 minutes is 3 minutes). During the other 7 minutes of the 10 minute period the Welding Power Source must idle and allowed to cool.

Introduction 2-1 Manual 0-5086

THERMAL ARC 95 S INTRODUCTION

2.07 Speciﬁ cations

Power Source Part Number W1003200

Welding Output

Welding Current Range 5 - 95 Amps

Nominal DC Open Circuit Voltage (OCV) 60V

Welding Output, 104º F (40º C), 10 min. (quoted ﬁ gures refer to SMAW output)

Rated Input Current (A) for STICK Welding 33.5A

Rated Input Current (A) for TIG Welding 21.0A

Rated Output for STICK Welding 90A / 23.6V @ 20%

Rated Output for TIG Welding 95A / 13.8V @ 20%

Duty Cycle (%) 20% @ 90A / 23.6V

Welder Type Inverter Power Source

Output Terminal Type Dinse 25

Mains Power

50A / 22V @ 100% 80A / 23.2V @ 30% 90A / 23.6V @ 20%

Io=90A@23.6V

Iο = 90A @ 23.6V

Io = 95A@13.8V

Number of Phases Single Phase

Nominal Supply Voltage 115V

Nominal Supply Frequency 50/60 Hz

Effective Input Current (l1eff) 15.0 Amps

Maximum Input Current (l1 max) Δ 33.5 Amps

Single Phase Generator Requirements 6 KVA

Classiﬁ cation

Protection Class IP23S

Standards IEC 60974-1

Cooling Method Fan Cooled

Dimensions and Weight

Welding Power Source Mass 9.7 lb. (4.4 kg) Welding Power Source Dimensions (Height x Width x Depth) H 13.0" x W 5.1" x D 9.0"

(H 330mm x W 130mm x D 230mm)

Δ The recommended time delay fuse or circuit breaker size is 30 amp. An individual branch circuit capable of

carrying 30 amperes and protected by fuses or circuit breaker is recommended for this application. Fuse size is based on not more than 200 percent of the rated input amperage of the welding power source (Based on Article 630, National Electrical Code).

Thermal Arc continuously strives to produce the best product possible and therefore reserves the right to change, improve or revise the speciﬁ cations or design of this or any product without prior notice. Such updates or changes do not entitle the buyer of equipment previously sold or shipped to the corresponding changes, updates, improvements or replacement of such items.

The values speciﬁ ed in the table above are optimal values, your values may differ. Individual equipment may differ from the above speciﬁ cations due to in part, but not exclusively, to any one or more of the following; variations or changes in manufactured components, installation location and conditions and local power grid supply conditions.

Manual 0-5086 2-2 Introduction

INSTALLATION THERMAL ARC 95 S

SECTION 3:

INSTALLATION

3.01 Environment

These units are designed for use in environments with increased hazard of electric shock. Examples of environments with increased hazard of electric shock are:

A. In locations in which freedom of movement is

restricted, so that the operator is forced to perform the work in a cramped (kneeling, sitting or lying) position with physical contact with conductive parts.

B. In locations which are fully or partially limited by

conductive elements, and in which there is a high risk of unavoidable or accidental contact by the operator.

C. In wet or damp hot locations where humidity or

perspiration considerably reduces the skin resistance of the human body and the insulation properties of accessories.

Environments with increased hazard of electric shock do not include places where electrically conductive parts in the near vicinity of the operator, which can cause increased hazard, have been insulated.

3.02 Location

Be sure to locate the welder according to the following guidelines:

• In areas, free from moisture and dust.

• Ambient temperature between 32°F (0°C) to 104° F (40° C).

3.03 Electrical Input Connections

WARNING

ELECTRIC SHOCK can kill; SIGNIFICANT DC VOLTAGE is present after removal of input power.

DO NOT TOUCH live electrical parts.

SHUT DOWN welding power source, disconnect input

power employing lockout/tagging procedures. Lock-out/ tagging procedures consist of padlocking line disconnect switch in open position, removing fuses from fuse box, or shutting off and red-tagging circuit breaker or other disconnecting device.

• Electrical Input Requirements

Operate the welding power source from a single-phase 50/60 Hz, AC power supply. The input voltage must match one of the electrical input voltages shown on the input data label on the unit nameplate. Contact the local electric utility for information about the type of electrical service available, how proper connections should be made, and inspection required. The line disconnect switch provides a safe and convenient means to completely remove all electrical power from the welding power supply whenever necessary to inspect or service the unit.

Do not connect an input (WHITE or BLACK) conductor to the ground terminal.

• In areas, free from oil, steam and corrosive gases.

• In areas, not subjected to abnormal vibration or shock.

• In areas, not exposed to direct sunlight or rain.

• Place at a distance of 12” (300mm) or more from walls or similar that could restrict natural air ﬂow for cooling

WARNING

Thermal Arc advises that this equipment be electrically connected by a qualified electrician.

Installation 3-1 Manual 0-5086

THERMAL ARC 95 S INSTALLATION

Art #: A-08473_AB

Welding Power Supply

Primary Power Cable

120 V, 20A, 1Ø

Refer to Figure 3-1:

1. Connect end of ground (GREEN or GREEN/YELLOW) conductor to a suitable ground. Use a grounding method that complies with all applicable electrical codes.

2. Connect ends of line 1 (BLACK) and line 2 (WHITE) input conductors to a de-energized line disconnect switch.

3. Use Table 3-1 as a guide to select line fuses for the disconnect switch.

Input Voltage Fuse Size

115V 30 Amps

CAUTION

The time-delay fuses or circuit breaker of an individual branch circuit may have nuisance tripping when welding with this product due to the amperage rating of the time-delay fuses or circuit breaker.

The recommended time-delay fuses or circuit breaker size is 30 amperes. Fuse/circuit breaker size is based on not more than 200 percent of the rated input amperage of the welding power source (Based on Article 630, National Electrical Code).

An individual branch circuit capable of carrying 30 amperes and time-delay fuses or circuit breaker protection is recommended for this application.

Figure 3-1: Electrical Input Connections

Manual 0-5086 3-2 Installation

INSTALLATION THERMAL ARC 95 S

Input Power

Each unit incorporates an INRUSH circuit. When the MAIN CIRCUIT SWITCH is turned on, the inrush circuit provides pre-charging for the input capacitors. A relay in the Power Control Assembly (PCA) will turn on after the input capacitors have charged to operating voltage (after approximately 5 seconds)

NOTE

Damage to the PCA could occur if 133 VAC or higher is applied to the Primary Power Cable.

Primary Supply Lead Size

Model

Thermal Arc 95 S 12 AWG (3.3mm²)

(Factory Fitted)

Table 3-2: Primary Circuit Sizes to Achieve Maximum Current

Minimum Primary

Current Circuit Size

(Vin/Amps)

115V/30A - 90A / 23.6V @ 20%

115V/21A 95A / 13.8V @ 20% -

Current & Duty Cycle

TIG STICK

Installation 3-3 Manual 0-5086

THERMAL ARC 95 S INSTALLATION

3.04 Electromagnetic Compatibility

WARNING

Extra precautions for Electromagnetic Compatibility may be required when this Welding Power Source is used in a domestic situation.

A. Installation and Use - Users Responsibility

The user is responsible for installing and using the welding equipment according to the manufacturer’s instructions. If electromagnetic disturbances are detected then it shall be the responsibility of the user of the welding equipment to resolve the situation with the technical assistance of the manufacturer. In some cases this remedial action may be as simple as earthing the welding circuit, see NOTE below. In other cases it could involve constructing an electromagnetic screen enclosing the Welding Power Source and the work, complete with associated input ﬁlters. In all cases, electromagnetic disturbances shall be reduced to the point where they are no longer Troublesome.

B. Assessment of Area

Before installing welding equipment, the user shall make an assessment of potential electromagnetic problems in the surrounding area. The following shall be taken into account.

1. Other supply cables, control cables, signaling and telephone cables; above, below and adjacent to the welding equipment.

2. Radio and television transmitters and receivers.

3. Computer and other control equipment.

8. The immunity of other equipment in the environment: the user shall ensure that other equipment being used in the environment is compatible: this may require additional protection measures.

The size of the surrounding area to be considered will depend on the structure of the building and other activities that are taking place. The surrounding area may extend beyond the boundaries of the premises.

C. Methods of Reducing Electromagnetic Emissions

1. Mains Supply

Welding equipment should be connected to the

mains supply according to the manufacturer’s recommendations. If interference occurs, it may be necessary to take additional precautions such as ﬁltering of the mains supply. Consideration should be given to shielding the supply cable of permanently installed welding equipment in metallic conduit or equivalent. Shielding should be electrically continuous throughout its length. The shielding should be connected to the Welding Power Source so that good electrical contact is maintained between the conduit and the Welding Power Source enclosure.

2. Maintenance of Welding Equipment

The welding equipment should be routinely maintained

according to the manufacturer’s recommendations. All access and service doors and covers should be closed and properly fastened when the welding equipment is in operation. The welding equipment should not be modiﬁed in any way except for those changes and adjustments covered in the manufacturer’s instructions. In particular, the spark gaps of arc striking and stabilizing devices should be adjusted and maintained according to the manufacturer’s recommendation

4. Safety critical equipment, e.g. guarding of industrial equipment.

5. The health of people around, e.g. the use of pacemakers and hearing aids.

6. Equipment used for calibration and measurement.

7. The time of day that welding or other activities are to be carried out.

Manual 0-5086 3-4 Installation

3. Welding Cables

The welding cables should be kept as short as possible

and should be positioned close together, running at or close to the ﬂoor level.

4. Equipotential Bonding

Bonding of all metallic components in the welding

installation and adjacent to it should be considered. However, metallic components bonded to the work piece will increase the risk that the operator could receive a shock by touching the metallic components and the electrode at the same time. The operator should be insulated from all such bonded metallic components.

INSTALLATION THERMAL ARC 95 S

5. Earthing of the Work Piece

Where the work piece is not bonded to earth for electri-

cal safety, nor connected to earth because of its size and position, e.g. ship’s hull or building steelwork, a connection bonding the work piece to earth may reduce emissions in some, but not all instances. Care should be taken to prevent the earthing of the work piece increasing the risk of injury to users, or damage to other electrical equipment. Where necessary, the connection of the work piece to earth should be made by direct connection to the work piece, but in some countries where direct connection is not permitted, the bonding should be achieved by suitable capacitance, selected according to national regulations.

6. Screening and Shielding

Selective screening and shielding of other cables

and equipment in the surrounding area may alleviate problems of interference. Screening the entire welding installation may be considered for special applications.

3.05 Setup for Welding

NOTE

Conventional operating procedures apply when using the Welding Power Source, i.e. connect work lead directly to work piece and electrode lead is used to hold electrode. Wide safety margins provided by the design ensure that the Welding Power Source will withstand short-term overload without adverse effects. The welding current range values should be used as a guide only. Current delivered to the arc is dependent on the welding arc voltage, and as welding arc voltage varies between different classes of electrodes, welding current at any one setting would vary according to the type of electrode in use. The operator should use the welding current range values as a guide then ﬁne tune the welding current to suit the application.

WARNING

Before connecting the work clamp to the work and inserting the electrode in the electrode holder make sure the Primary power supply is switched off.

Installation 3-5 Manual 0-5086

THERMAL ARC 95 S INSTALLATION

200A

Set Welding Current as speciﬁed by the Electrode Manufacturer.

Set Process Selection Switch to Stick.

Positive Output Terminal (Dinse™ 25)

Negative Output Terminal (Dinse™ 25)

Art #: A-08602

3.06 STICK (SMAW) Setup

Stick Mode Sequence of Operation

Before any welding is to begin, be sure to wear all appropriate and recommended safety equipment.

1. Switch the ON/OFF Switch (located on the rear panel) to OFF.

2. Connect the ground clamp cable to the negative output terminal, and the electrode holder cable to the positive output terminal.

This set up is known as DC Electrode Positive or reverse polarity. Please consult with the stick electrode manufacturer for speciﬁc polarity recommendations.

CAUTION

NOTE

Figure 3-2: Setup for STICK Welding

3. Connect the ground clamp to your workpiece.

4. Plug the power cable into the appropriate outlet, and turn the switch to the “ON” position. The power L.E.D light should illuminate.

5. Set the “Process Selection Switch” to Stick

6. Set the weld current control knob to the desired amperage.

7. Install a stick electrode in the electrode holder.

8. You are now ready to begin Stick Welding

NOTE

Gently strike the electrode on the work piece to generate a welding arc, and slowly move along the work piece while holding a consistent arc length above base metal.

Manual 0-5086 3-6 Installation

INSTALLATION THERMAL ARC 95 S

Set Process Selection Switch to LIFT TIG.

Positive Output Terminal (Dinse™ 25)

Negative Output Terminal (Dinse™ 25)

Art #: A-08603

Set Welding Current as speciﬁed by the Electrode Manufacturer.

Secure the gas cylinder in an upright position by chaining it to a stationary support to prevent falling or tipping.

3.07 Lift TIG (GTAW) Setup

Lift TIG Sequence of Operation

Before any welding is to begin, be sure to wear all appropriate and recommended safety equipment.

1. Switch the ON/OFF Switch (located on the rear panel) to OFF.

2. Connect the ground clamp cable to positive output terminal, and the TIG torch cable to the negative output terminal.

This set up is known as Straight Polarity or DC Electrode Negative. This is commonly used for DC TIG welding on most materials such as steel and stainless steel.

Figure 3-3: Setup for Lift TIG (GTAW) Welding

CAUTION

NOTE

3. Using a secured Argon cylinder, slowly crack open then close the cylinder valve while standing off to the side of the valve. This will remove any debris that may be around the valve & regulator seat area.

4. Install the regulator and tighten with a wrench.

5. Connect the gas hose to the outlet of the Argon regulator, and tighten with a wrench.

6. Be sure the gas valve on the torch is closed, and slowly open the Argon Cylinder Valve to the fully open position.

7. Connect the ground clamp to your work piece.

8. Plug the power cable into the appropriate outlet, and turn the switch to the “ON” position. The power L.E.D. light should illuminate.

Installation 3-7 Manual 0-5086

THERMAL ARC 95 S INSTALLATION

9. Set the “Process Selection Switch” to LIFT TIG

10. Set the weld current control knob to the desired amperage.

11. The tungsten must be ground to a blunt point in order to achieve optimum welding results. It is critical to grind the tungsten electrode in the direction the grinding wheel is turning.

12. Install the tungsten with approximately 1/8” to ¼” sticking out from the gas cup, ensuring you have correct sized collet.

13. Tighten the back cap.

14. You are now ready to begin TIG Welding

NOTE

Open the gas valve on TIG torch handle, and adjust the pressure of regulator to 15-25 cubic feet per hour. This gas ﬂow should be sufﬁcient for most TIG welding applications.

ii. Touch the tungsten to the work piece. This closes the welding circuit, and the arc starts by slowly LIFTING the torch off the base metal. Keep a consistent arc length of about 1/8-1/4”.

iii. If necessary re-adjust the amperage setting to an appropriate level.

Manual 0-5086 3-8 Installation

OPERATION THERMAL ARC 95 S

15A

OUTLET

MAX STICK

15A OUTLET MAX TIG

Art # A-08707_AB

(A) Process Selection Switch

(B) Power On Indicator

(D) Welding Current Control

SECTION 4:

OPERATION

Conventional operating procedures apply when using the Welding Power Source, i.e. connect work lead directly to work piece and electrode lead is used to hold the electrode. The welding current range values should be used as a guide only. Current delivered to the arc is dependent on the welding arc voltage, and as welding arc voltage varies between different classes of electrode, welding current at any one setting would vary according to the type of electrode in use. The operator should use the welding current range values as a guide then ﬁne tune the welding current to suit the speciﬁc application. Refer to the electrode manufacture's literature for further information.

4.01 Front Panel

(A) Process Selection Switch

Switches between Lift TIG and STICK Welding modes.

(B) Power On Indicator

The Power ON Indicator illuminates when the ON/OFF switch is in the ON position and the nominal mains voltage is present.

The welding power source is protected by a self resetting thermostat. The indicator will illuminate if the duty cycle of the power source has been exceeded. If the Over Heat light illuminates wait for the Over Heat light to extinguish before resuming welding.

(D) Welding Current Control

The welding current is increased by turning the Weld Current control knob clockwise or decreased by turning the Weld Current control knob counterclockwise. The welding current should be set according to the speciﬁc application. Refer to the electrode manufacture's literature for further information.

(E) ON/OFF Switch (located on rear panel - not shown)

This switch controls the Mains Supply Voltage to the Power Source.

Operation 4-1 Manual 0-5086

Figure 4-1: 95 S Controls

THERMAL ARC 95 S OPERATION

4.02 SMAW Electrode Polarity

Stick electrodes are generally connected to the "+" Positive Output Terminal and the work lead to the "−" Negative Output Terminal but if in doubt consult the electrode manufacturers literature for further information.

4.03 Effects of Stick Welding Various Materials

High Tensile and Alloy Steels

The two most prominent effects of welding these steels are the formation of a hardened zone in the weld area, and, if suitable precautions are not taken, the occurrence in this zone of under-bead cracks. Hardened zone and under-bead cracks in the weld area may be reduced by using the correct electrodes, preheating, using higher current settings, using larger electrodes sizes, short runs for larger electrode deposits or tempering in a furnace.

Manganese Steels

The effect on manganese steel of slow cooling from high temperatures is to embrittle it. For this reason it is absolutely essential to keep manganese steel cool during welding by quenching after each weld or skip welding to distribute the heat.

Cast Iron

Most types of cast iron, except white iron, are weldable. White iron, because of its extreme brittleness, generally cracks when attempts are made to weld it. Trouble may also be experienced when welding white-heart malleable, due to the porosity caused by gas held in this type of iron.

Copper and Alloys

The most important factor is the high rate of heat conductivity of copper, making pre-heating of heavy sections necessary to give proper fusion of weld and base metal.

Types of Electrodes

Arc Welding electrodes are classiﬁed into a number of groups depending on their applications. There are a great number of electrodes used for specialized industrial purposes which are not of particular interest for everyday general work. These include some low hydrogen types for high tensile steel, cellulose types for welding large diameter pipes, etc The range of electrodes dealt with in this publication will cover the vast majority of applications likely to be encountered; are all easy to use.

Metal Being Joined Electrode Comments

Ideal electrodes for all general purpose work, features

Mild Steel 6013

Mild Steel 7014

Cast Iron 99% Nickel Suitable for joining all cast irons except white cast iron.

Stainless Steel 318L-16 High corrosion resistances. Ideal for dairy work etc.

Copper, Bronze, Etc.

Copper, Bronze, Dissimilar Metals,

Crack Resistance, All Hard-to

Weld Jobs

Bronze

5.7 ERCUSI-A

312-16

include outstanding operator appeal, easy arc starting,

All positional eletrode for use on mild and galvanized

steel furniture, plates, fences, gates, piples and tanks,

etc. Especially suitable for vertical-down welding.

Easy to use electrode for marine ﬁttings, water taps and

valves, water through ﬂoats arms, etc. Also for joining copper to steel and for bronze overlays on steel shafts.

It will weld most problematic jobs such as springs,

shafts, broken joins, mild steel to stainless and alloy

steels. Not suitable for aluminum.

and low spatter.

Manual 0-5086 4-2 Operation

OPERATION THERMAL ARC 95 S

4.04 GTAW Electrode Polarity

Connect the TIG torch to the "-" Negative Output Terminal and the work lead to the "+" Positive Output Terminal for direct current straight polarity. Direct current straight polarity is the most widely used polarity for DC TIG welding. It allows limited wear of the electrode since 70% of the heat is concentrated at the work piece.

4.05 Guide for Selecting Filler Wire

Filler Wire Diameter DC Current (Amps)

1/16" (1.6mm) 20 - 90 3/32" (2.4mm) 60 - 115

4.08 Tungsten Electrode Types

Electrode Type

(Ground Finish)

Thoriated 2%

Ceriated 2%

DC welding of mild steel, stainless steel

AC & DC welding of mild steel, stainless

steel, copper, aluminum, magnesium and

Welding Application Features Color Code

and copper.

their alloys.

4.06 Tungsten Electrode Current Ranges

Electrode Diameter DC Current

.040" (1.0mm) 20 - 90 1/16" (1.6mm) 60 - 115

4.07 Shielding Gas Selection

Alloy Shielding Gas

Carbon Steel Welding Argon

Stainless Steel Welding Argon

Nickel Alloy Welding Argon

Copper Welding Argon

Titanium Welding Argon

Excellent arc starting, long life, high

current carrying capacity.

Longer life, more stable arc, easier

starting, wider current range,

narrower & more concentrated arc.

Red

Grey

4.09 TIG Welding Parameters for Steel

DC Current

Base Metal

Thickness

0.040"

(1.0mm)

0.045"

(1.22mm)

1/16"

(1.6mm)

1/8"

(3.2mm)

Mild Steel

35-45 20-30

40-50 25-35 Lap/Filler

45-55 30-45

50-60 35-50 Lap/Filler

60-70 40-60

70-90 50-70 Lap/Filler

80-100 65-85

90-115 90-110 Lap/Filler

Stainless

Steel

Electrode

Diameter

0.040"

(1.0mm)

0.040"

(1.0mm)

1/16"

(1.6mm)

1/16" (1.16mm) 3/32" (2.4mm)

Filler Rod

Diameter

1/16"

(1.6mm)

1/16"

(1.6mm)

1/16"

(1.6mm)

Argon Gas Flow

Rate Joint / Type

10 CFH

(5 LPM)

13 CFH

(6 LPM)

15 CFH

(7 LPM)

15CFH

(7 LPM)

Butt/Corner

Operation 4-3 Manual 0-5086

THERMAL ARC 95 S OPERATION

Art # A-07687

Art # A-07688

Art # A-07689

Art # A-07690

Art A-07691

Art # A-07692

Art# A-07693

Art # A-07694

4.10 Arc Welding Practice

The techniques used for arc welding are almost identical regardless of what types of metals are being joined. Naturally enough, different types of electrodes would be used for different metals as described in the preceding section.

4.11 Welding Position

The electrodes dealt with in this publication can be used in most positions, i.e. they are suitable for welding in ﬂat, horizontal, vertical and overhead positions. Numerous applications call for welds to be made in positions intermediate between these. Some of the common types of welds are shown in Figures 4-2 through 4-9.

Figure 4-2: Flat position, down hand butt weld

Figure 4-6: Vertical position, butt weld

Figure 4-3: Flat position, gravity ﬁllet weld

Figure 4-4: Horizontal position, butt weld

Figure 4-5: Horizontal - Vertical (HV) position

Figure 4-7: Vertical position, ﬁllet weld

Figure 4-8: Overhead position, butt weld

Manual 0-5086 4-4 Operation

Figure 4-9: Overhead position, ﬁllet weld

OPERATION THERMAL ARC 95 S

Gap varies from 1/16” (1.6mm) to 3/16” (4.8mm) depending on plate thickness

Joint

Open Square Butt

1/16” (1.6mm) max

1.6mm (1/16”)

Single Vee Butt Joint

Not less than

70°

Double Vee Butt Joint

1/16” (1.6mm)

Lap Joint

Tee Joints

(Fillet both sides of the

joint)

Edge Joint

Fillet Joint

Corner Weld

Plug Weld Plug Weld

Not less than

70°

Single Vee Butt Joint

Not less than

45°

1/16” (1.6mm) max

Art # A-07695_AB

4.12 Joint Preparations

In many cases, it will be possible to weld steel sections without any special preparation. For heavier sections and for repair work on castings, etc., it will be necessary to cut or grind an angle between the pieces being joined to ensure proper penetration of the weld metal and to produce sound joints.

In general, surfaces being welded should be clean and free of rust, scale, dirt, grease, etc. Slag should be removed from oxy-cut surfaces. Typical joint designs are shown in Figure 4-10.

Figure 4-10: Typical joint designs for arc welding

Operation 4-5 Manual 0-5086

THERMAL ARC 95 S OPERATION

Art # A-07696

4.13 Arc Welding Technique

A Word to Beginners

For those who have not yet done any welding, the simplest way to commence is to run beads on a piece of scrap plate. Use mild steel plate about 6.0mm thick and a 3.2mm electrode. Clean any paint, loose scale or grease off the plate and set it ﬁrmly on the work bench so that welding can be carried out in the downhand position. Make sure that the work clamp is making good electrical contact with the work, either directly or through the work table. For light gauge material, always clamp the work lead directly to the

job, otherwise a poor circuit will probably result.

4.14 The Welder

Place yourself in a comfortable position before beginning to weld. Get a seat of suitable height and do as much work as possible sitting down. Don’t hold your body tense. A taut attitude of mind and a tensed body will soon make you feel tired. Relax and you will ﬁnd that the job becomes much easier. You can add much to your peace of mind by wearing a leather apron and gauntlets. You won’t be worrying then about being burnt or sparks setting alight to your clothes.

is broken again. A little practice will soon remedy both of these faults.

Figure 4-11: Striking an arc

4.16 Arc Length

The securing of an arc length necessary to produce a neat weld soon becomes almost automatic. You will ﬁnd that arc produces a crackling or spluttering noise and the weld metal comes across in large, irregular blobs. The weld bead is ﬂattened and spatter increases. A short arc is essential if a high quality weld is to be obtained although if it is too short there is the danger of it being blanketed by slag and the electrode tip being solidiﬁed in. If this should happen, give the electrode a quick twist back over the weld to detach it. Contact or “touch-weld” electrodes such as E7014 electrode do not stick in this way, and make welding much easier.

Place the work so that the direction of welding is across, rather than to or from, your body. The electrode holder lead should be clear of any obstruction so that you can move your arm freely along as the electrode burns down. If the lead is slung over your shoulder, it allows greater freedom of movement and takes a lot of weight off your hand. Be sure the insulation on your cable and electrode holder is not faulty, otherwise you are risking an electric shock.

4.15 Striking the Arc

Practice this on a piece of scrap plate before going on to more exacting work. You may at ﬁrst experience difﬁculty due to the tip of the electrode “sticking” to the work piece. This is caused by making too heavy a contact with the work and failing to withdraw the electrode quickly enough. A low amperage will accentuate it. This freezing-on of the tip may be overcome by scratching the electrode along the plate surface in the same way as a match is struck. As soon as the arc is established, maintain a 1/16" (1.6mm) to 1/8" (3.2mm) gap between the burning electrode end and the parent metal. Draw the electrode slowly along as it melts down.

Another difﬁculty you may meet is the tendency, after the arc is struck, to withdraw the electrode so far that the arc

Manual 0-5086 4-6 Operation

4.17 Rate of Travel

After the arc is struck, your next concern is to maintain it, and this requires moving the electrode tip towards the molten pool at the same rate as it is melting away. At the same time, the electrode has to move along the plate to form a bead. The electrode is directed at the weld pool at about 20° from the vertical. The rate of travel has to be adjusted so that a well-formed bead is produced.

If the travel is too fast, the bead will be narrow and strung out and may even be broken up into individual globules. If the travel is too slow, the weld metal piles up and the bead will be too large.

4.18 Making Welded Joints

Having attained some skill in the handling of an electrode, you will be ready to go on to make up welded joints.

A. Butt Welds

Set up two plates with their edges parallel, as shown in Figure 4-12, allowing 1/15" (1.6mm) to 3/32" (2.4mm) gap between them and tack weld at both ends. This is to prevent contraction stresses from the cooling weld metal pulling the plates out of alignment. Plates thicker than 1/4" (6.0mm) should have their mating edges beveled to form

OPERATION THERMAL ARC 95 S

Art # A-07697

Art # A-07698

Art # A-07699

Art # A-07700

a 70° to 90° included angle. This allows full penetration of the weld metal to the root. Using a 1/8" (3.2mm) E7014 electrode at 120 amps, deposit a run of weld metal on the bottom of the joint.

Do not weave the electrode, but maintain a steady rate of travel along the joint sufﬁcient to produce a well-formed bead. At ﬁrst you may notice a tendency for undercut to form, but keeping the arc length short, the angle of the electrode at about 20° from vertical, and the rate of travel not too fast, will help eliminate this. The electrode needs to be moved along fast enough to prevent the slag pool from getting ahead of the arc. To complete the joint in thin plate, turn the job over, clean the slag out of the back and deposit a similar weld.

B. Fillet Welds

These are welds of approximately triangular cross-section made by depositing metal in the corner of two faces meeting at right angles. Refer to Figure 4-5.

A piece of angle iron is a suitable specimen with which to begin, or two lengths of strip steel may be tacked together at right angles. Using a 1/8" (3.2mm) E7014 electrode at 120 amps, position angle iron with one leg horizontal and the other vertical. This is known as a horizontal-vertical (HV) fillet. Strike the arc and immediately bring the electrode to a position perpendicular to the line of the ﬁllet and about 45° from the vertical. Some electrodes require to be sloped about 20° away from the perpendicular position to prevent slag from running ahead of the weld. Refer to Figure 4-14. Do not attempt to build up much larger than 1/4" (6.4mm) width with a 1/8" (3.2mm) electrode, otherwise the weld metal tends to sag towards the base, and undercut forms on the vertical leg. Multiruns can be made as shown in Figure 4-15. Weaving in HV ﬁllet welds is undesirable.

Figure 4-12: Butt weld

Figure 4-13: Weld build up sequence

Heavy plate will require several runs to complete the joint. After completing the ﬁrst run, chip the slag out and clean the weld with a wire brush. It is important to do this to prevent slag being trapped by the second run. Subsequent runs are then deposited using either a weave technique or single beads laid down in the sequence shown in Figure 4-13. The width of weave should not be more than three times the core wire diameter of the electrode. When the joint is completely ﬁlled, the back is either machined, ground or gouged out to remove slag which may be trapped in the root, and to prepare a suitable joint for depositing the backing run. If a backing bar is used, it is not usually necessary to remove this, since it serves a similar purpose to the backing run in securing proper fusion at the root of the weld.

Figure 4-14: Electrode position for HV ﬁllet weld

Figure 4-15: Multi-runs in HV ﬁllet weld

C. Vertical Welds

1. Vertical Up

Tack weld a three feet length of angle iron to your

work bench in an upright position. Use a 1/8" (3.2mm) E7014 electrode and set the current at 120 amps. Make yourself comfortable on a seat in front of the job and strike the arc in the corner

Operation 4-7 Manual 0-5086

THERMAL ARC 95 S OPERATION

Art # A-07701

Art # A-07702

Art # A-07703

Art # A-07704

of the ﬁllet. The electrode needs to be about 10° from the horizontal to enable a good bead to be deposited. Refer Figure 4-16. Use a short arc, and do not attempt to weave on the ﬁrst run. When the ﬁrst run has been completed de-slag the weld deposit and begin the second run at the bottom. This time a slight weaving motion is necessary to cover the ﬁrst run and obtain good fusion at the edges. At the completion of each side motion, pause for a moment to allow weld metal to build up at the edges, otherwise undercut will form and too much metal will accumulate in the centre of the weld. Figure 4-17 illustrates multi-run technique and Figure 4-18 shows the effects of pausing at the edge of weave and of weaving too rapidly.

Figure 4-16: Single run vertical ﬁllet weld

2. Vertical Down

TheE7014 electrode makes welding in this position

particularly easy. Use a 1/8" (3.2mm) electrode at 120 amps. The tip of the electrode is held in light contact with the work and the speed of downward travel is regulated so that the tip of the electrode just keeps ahead of the slag. The electrode should point upwards at an angle of about 45°.

3. Overhead Welds

Apart from the rather awkward position necessary,

overhead welding is not much more difficult that downhand welding. Set up a specimen for overhead welding by ﬁrst tacking a length of angle iron at right angles to another piece of angle iron or a length of waste pipe. Then tack this to the work bench or hold in a vice so that the specimen is positioned in the overhead position as shown in the sketch. The electrode is held at 45° to the horizontal and tilted 10° in the line of travel (Figure 4-19). The tip of the electrode may be touched lightly on the metal, which helps to give a steady run. A weave technique is not advisable for overhead ﬁllet welds. Use a 1/8" (3.2mm) E6012 electrode at 120 amps, and deposit the ﬁrst run by simply drawing the electrode along at a steady rate. You will notice that the weld deposit is rather convex, due to the effect of gravity before the metal freezes.

Figure 4-17: Multi run vertical ﬁllet weld

Figure 4-18: Examples of vertical ﬁllet welds

Manual 0-5086 4-8 Operation

Figure 4-19: Overhead ﬁllet weld

4.19 Distortion

Distortion in some degree is present in all forms of welding. In many cases it is so small that it is barely perceptible, but in other cases allowance has to be made before welding commences for the distortion that will subsequently occur. The study of distortion is so complex that only a brief outline can be attempted hear.

OPERATION THERMAL ARC 95 S

Art # A-07706

Art # A-07705

4.20 The Cause of Distortion

Distortion is cause by:

A. Contraction of Weld Metal:

Molten steel shrinks approximately 11 per cent in volume on cooling to room temperature. This means that a cube of molten metal would contract approximately 2.2 per cent in each of its three dimensions. In a welded joint, the metal becomes attached to the side of the joint and cannot contract freely. Therefore, cooling causes the weld metal to ﬂow plastically, that is, the weld itself has to stretch if it is to overcome the effect of shrinking volume and still be attached to the edge of the joint. If the restraint is very great, as, for example, in a heavy section of plate, the weld metal may crack. Even in cases where the weld metal does not crack, there will still remain stresses “locked-up” in the structure. If the joint material is relatively weak, for example, a butt joint in 2.0mm sheet, the contracting weld metal may cause the sheet to become distorted.

B. Expansion and Contraction of Parent Metal in the Fusion Zone:

While welding is proceeding, a relatively small volume of the adjacent plate material is heated to a very high temperature and attempts to expand in all directions. It is able to do his freely at right angles to the surface of the plate (i.e., “through the weld”), but when it attempts to expand “across the weld” or “along the weld”, it meets considerable resistance, and to fulﬁl the desire for continued expansion, it has to deform plastically, that is, the metal adjacent to the weld is at a high temperature and hence rather soft, and, by expanding, pushes against the cooler, harder metal further away, and tends to bulge (or is “upset”). When the weld area begins to cool, the “upset” metal attempts to contract as much as it expanded, but, because it has been “upset”, it does not resume its former shape, and the contraction of the new shape exerts a strong pull on adjacent metal. Several things can then happen.

The metal in the weld area is stretched (plastic deformation), the job may be pulled out of shape by the powerful contraction stresses (distortion), or the weld may crack, in any case, there will remain “locked-up” stresses in the job. Figures 4-20 and 4- 21 illustrate how distortion is created.

Figure 4-21: Parent metal contraction

4.21 Overcoming Distortion Effects

There are several methods of minimizing distortion effects.

A. Peening

This is done by hammering the weld while it is still hot. The weld metal is ﬂattened slightly and because of this the tensile stresses are reduced a little. The effect of peening is relatively shallow, and is not advisable on the last layer.

B. Distribution of Stresses

Distortion may be reduced by selecting a welding sequence which will distribute the stresses suitably so that they tend to cancel each other out. See Figures 4-25 through 4-28 for various weld sequences. Choice of a suitable weld sequence is probably the most effective method of overcoming distortion, although an unsuitable sequence may exaggerate it. Simultaneous welding of both sides of a joint by two welders is often successful in eliminating distortion.

C. Restraint of Parts

Forcible restraint of the components being welded is often used to prevent distortion. Jigs, positions, and tack welds are methods employed with this in view.

D. Presetting

It is possible in some cases to tell from past experience or to ﬁnd by trial and error (or less frequently, to calculate) how much distortion will take place in a given welded structure. By correct pre-setting of the components to be welded, constructional stresses can be made to pull the parts into correct alignment. A simple example is shown in Figure 4-22.

Operation 4-9 Manual 0-5086

Figure 4-20: Parent metal expansion

THERMAL ARC 95 S OPERATION

Art # A-07707

Art # A-07708

PreheatPreheat

Dotted lines show effect if no preheat is used

Weld

Art # A-07709

Art # A-07710

Art # A-07711

Art # A-07712

Art # A-07713

E. Preheating

Suitable preheating of parts of the structure other than the area to be welded can be sometimes used to reduce distortion. Figure 4-23 shows a simple application. By removing the heating source from b and c as soon as welding is completed, the sections b and c will contract at a similar rate, thus reducing distortion.

Figure 4-26: Step back sequence

Figure 4-22: Principle of presetting

Figure 4-27: Chain intermittent welding

Figure 4-23: Reduction of distortion by preheating

Figure 4-24: Examples of distortion

Figure 4-28: Staggered intermittent welding

Figure 4-25: Welding sequence

Manual 0-5086 4-10 Operation

SERVICE THERMAL ARC 95 S

Warning! Disconnect input power before maintaining.

Each Use

Visual check of regulator and pressure

Visual check of torch Consumable parts

Weekly

Visually inspect the torch body and consumables

Visually inspect the cables and leads. Replace as needed

3 Months

Clean exterior of power supply

6 Months

Replace all broken parts

Bring the unit to an authorized Thermal Arc Service Center to remove any accumulated dirt and dust from the interior. This may need to be done more frequently under exceptionally dirty conditions.

Maintain more often if used under severe conditions

Art # A-08549_AB

SECTION 5:

SERVICE

5.01 Maintenance and Inspection

The only routine maintenance required for the power supply is a thorough cleaning and inspection, with the frequency depending on the usage and the operating environment.

To clean the unit, open the enclosure and use a vacuum cleaner to remove any accumulated dirt and dust. The unit should also be wiped clean, if necessary; with solvents that are recommended for cleaning electrical apparatus.

WARNING

There are extremely dangerous voltages and power levels present inside this product. Disconnect primary power at the source before opening the enclosure. Wait at least two minutes before opening the enclosure to allow the primary capacitors to discharge.

CAUTION

Do not blow air into the power supply during cleaning. Blowing air into the unit can cause metal particles to interfere with sensitive electrical components and cause damage to the unit.

Service 5-1 Manual 0-5086

THERMAL ARC 95 S SERVICE

Insufﬁcient Gap

Incorrect Sequence

Art # A-05866_AC

Not cleaned, or incorrect electrode

Slag trapped in undercut

Slag trapped in root

Art # A-05868_AB

Art # A-05867_AC

Lack of inter-run fusion

Lack of side fusion, scale dirt, small electrode, amperage too low

Lack of root fusion

Lack of fusion caused by dirt, electrode angle incorrect, rate of travel too high

5.02 STICK Welding Problems

Description Possible Cause Remedy

1. Gas pockets or voids in weld metal (Porosity).

A. Electrodes are damp.

B. Welding current is too high.

A. Dry electrodes before use.

B. Reduce welding current.

2. Crack occurring in weld metal soon after solidiﬁcation commences.

3. A gap is left by failure of the weld metal to ﬁll the root of the weld.

4. Portions of the weld run do not fuse to the surface of the metal or edge of the joint

C. Surface impurities such as oil,

grease, paint, etc.

A. Rigidity of joint.

B. Insufficient throat thickness.

C. Cooling rate is too high. A. Welding current is too low.

B. Electrode too large for joint.

C. Insufﬁcient gap.

D. Incorrect sequence.

A. Small electrodes used on

heavy cold plate.

B. Welding current is too low.

C. Wrong electrode angle.

C. Clean joint before welding

A. Redesign to relieve weld joint of severe

stresses or use crack resistance electrodes.

B. Travel slightly slower to allow greater

build up in throat.

C. Preheat plate and cool slowly. A. Increase welding current

B. Use smaller diameter electrode.

C. Allow wider gap.

D. Use correct build-up sequence.

A. Use larger electrodes and preheat

the plate.

B. Increase welding current

C. Adjust angle so the welding arc is

directed more into the base metal

5. Non-metallic particles are trapped in the weld metal (slag inclusion).

Manual 0-5086 5-2 Service

D. Travel speed of electrode is too

high.

E. Scale or dirt on joint surface.

A. Non-metallic particles may

be trapped in undercut from previous run.

B. Joint preparation too restricted.

C. Irregular deposits allow slag to

be trapped.

D. Lack of penetration with slag

trapped beneath weld bead.

E. Rust or mill scale is preventing

full fusion.

F. Wrong electrode for position in

which welding is done.

D. Reduce travel speed of electrode

E. Clean surface before welding.

A. If bad undercut is present, clean slag

out and cover with a run from a smaller diameter electrode.

B. Allow for adequate penetration and

room for cleaning out the slag.

C. If very bad, chip or gr i nd out

irregularities.

D. Use smaller electrode with sufﬁcient

current to give adequate penetration. Use suitable tools to remove all slag from corners.

E. Clean joint before welding.

F. Use electrodes designed for position

in which welding is done, otherwise proper control of slag is difﬁcult.

SERVICE THERMAL ARC 95 S

5.03 TIG Welding Problems

Weld quality is dependent on the selection of the correct consumables, maintenance of equipment and proper welding technique.

Description Possible Cause Remedy

1. Excessive beard build-up or poor penetration or poor fusion at edges of weld.

2. Weld bead too wide and ﬂat or undercut at edges of weld or excessive burn through.

3. Weld bead too small or insufﬁcient penetration or ripples in bead are widely spaced apart.

4. Weld bead too wide or excessive bea d bu ild up or ex cess ive penetration in butt joint.

5. Uneven leg length in ﬁllet joint. Wrong placement of ﬁller rod. Re-position ﬁller rod.

6. E lectrode melts when arc is struck.

7. Dirty weld pool. A. Electrode contaminated through

8. Poor weld ﬁnish. Inadequate shielding gas. Increase gas ﬂow or check gas line

9. Arc ﬂutters during TIG welding. Tungsten electrode is too large

10. We l d in g ar c c a nn o t b e established.

11. Electrode melts or oxidizes when an arc is struck.

Welding current is too low Increase weld current and/or

change joint preparation.

Welding current is too high. Decrease welding current.

Travel speed too fast. Reduce travel speed.

Travel speed is too slow. Increase travel speed.

Electrode is connected to the "+"

Positive Output Terminal.

contact with work piece or ﬁller rod material.

B. Gas contaminated with air.

for the welding current.

A. Work clamp is not connected to

the work piece or the work/torch leads are not connected to the correct welding terminals.

B. Torch lead is disconnected.

C. Gas ﬂow incorrectly set, cylinder

empty or the torch valve is off.

A. No gas is flowing to welding

region. B. Torch is clogged with dust. C. Gas hose is cut. D. Gas passage contains impurities.

E. Gas regulator turned off. F. Torch valve is turned off.

G. The electrode is too small for the

welding current.

Connect th e elec trode to th e

"-" Negative Output Terminal.

A. Clean the electrode by grinding

contaminates off.

B. Check gas lines for cuts and loose

ﬁtting or change gas cylinder.

for problems

Select the right size electrode.

Refer to section Tungsten Electrode Current Ranges.

A. Connect the work clamp to the

work piece or connect the work/ torch leads to the correct welding terminals.

B. Connect it to the "-" Negative

Output Terminal.

C. Select the right ﬂow rate, change

cylinder or turn torch valve on.

A. Check the gas lines for kinks or

breaks or cylinder contains gas. B. Clean torch. C. Replace gas hose. D. Disconnect gas hose from torch

then raise gas pressure and blow

out impurities. E. Turn on. F. Turn on. G. Increase electrode diameter or

reduce the welding current.

Service 5-3 Manual 0-5086

THERMAL ARC 95 S SERVICE

TIG Welding Problems (Continued)

Description Possible Cause Remedy

12. Arc start is not smooth. A. Tungsten electrode is too large for the welding current.

B. The wrong electrode is being

used for the welding job.

C. Gas flow rate is too high.

D. Incorrect shield gas is being

used.

E. Poor work clamp connection

to work piece.

WARNING

There are extremely dangerous voltages and power levels present inside this product. Do not attempt to repair unless you are an Accredited Thermal Arc Service Agent and you have had training in power measurements and troubleshooting techniques. If major complex subassemblies are faulty, then the Welding Power Source must be returned to an Accredited Thermal Arc Service Agent for repair.

A. Refer to section Tungsten Electrode

Current Ranges for the correct size.

B. Refer to section Tungsten Electrode

Types for the correct electrode type.

C. Select the correct ﬂow rate for the

welding job.

D. Use 100% argon for TIG welding.

E. Improve connection to work piece.

5.04 Power Source Problems

Manual 0-5086 5-4 Service

APPENDIX THERMAL ARC 95 S

APPENDIX 1: REPLACEMENT PARTS

Description Part No.

Fan, 24V DC, 95S W7003004 Rectiﬁer Bridge, 700V, 50A, 95S W7003010 Current Sensor, 95S W7003013 Thermistor, 95S W7003016 Terminal, Output, 95S W7003019 Handle, 95S W7003040 Knob, Control, Red, 20 OD x 6 ID W7003041 Panel, Base, 95S W7003042 Panel, Cover, 95S W7003043 Panel, Front, 95S W7003044 Panel, Rear, 95S W7003045 PCB, Control, 95S W7003046 PCB, Front Control, 95S W7003047 PCB, Power, 95S W7003048 Strap, Shoulder, 95S W7003049 Switch, On/Off, 95S W7003050

Appendix A-1 Manual 0-5086

THERMAL ARC 95 S APPENDIX

APPENDIX 2: OPTIONS AND ACCESSORIES

Description Part Number

17V style TIG Torch with 3m lead, gas valve, 25mm dinse connection and accessory kit W4012500

Argon Shielding Gas Regulator with 5/8"-18 UNF Hose Connection 600300

Power Adapter-115V,20A Socket to 15A Plug W4013300

USA Graphics Auto-Darkening welding helmet, spare cover lens and operating manual W4011700

Canadian Graphics Auto-Darkening welding helmet, spare cover lens and operating manual W4011800

Claret Color Auto-Darkening welding helmet, spare cover lens and operating manual W4011900

Black Graphics Auto-Darkening welding helmet, spare cover lens and operating manual W4012000

Manual 0-5086 A-2 Appendix

APPENDIX THERMAL ARC 95 S

AC1AC

-24V

TRANS2

Pr2

OC1

OC2

Pr1

DR1

DR2

DR5

DR6

DR3

DR4

DR7

DR8

DR1

DR2

DR3

DR4

DR5

DR8

DR6

DR7

OC1 OC2

K1 AC115V/60HZ

FAN

LED1

LED2

VR1

PTC

IGBT

Art # A-09016

APPENDIX 3: SYSTEM SCHEMATIC

Appendix A-3 Manual 0-5086

THERMAL ARC 95 S APPENDIX

This Page Intentionally Blank

Manual 0-5086 A-4 Appendix

LIMITED WARRANTY

This information applies to Thermal Arc products that were purchased in the USA and Canada.

November 2007

LIMITED WARRANTY: Thermal Arc®, Inc., A Thermadyne Company (“Thermal Arc”), warrants to customers of authorized distributors (“Purchaser”) that its products will be free of defects in workmanship or material. Should any failure to conform to this warranty appear within the

warranty period stated below, Thermal Arc shall, upon notication thereof and substantiation that

the product has been stored, installed, operated, and maintained in accordance with Thermal

Arc’s specications, instructions, recommendations and recognized standard industry practice, and not subject to misuse, repair, neglect, alteration, or damage, correct such defects by suitable

repair or replacement, at Thermal Arc’s sole option, of any components or parts of the product determined by Thermal Arc to be defective.

This warranty is exclusive and in lieu of any warranty of merchantability,

tness for any particular purpose, or other warranty of quality, whether

express, implied, or statutory.

Limitation of liability: Thermal Arc shall not under any circumstances be liable for special, indirect,

incidental, or consequential damages, including but not limited to lost prots and business

interruption. The remedies of the purchaser set forth herein are exclusive, and the liability of

Thermal Arc with respect to any contract, or anything done in connection therewith such as the

performance or breach thereof, or from the manufacture, sale, delivery, resale, or use of any

goods covered by or furnished by Thermal Arc, whether arising out of contract, tort, including negligence or strict liability, or under any warranty, or otherwise, shall not exceed the price of the goods upon which such liability is based.

No employee, agent, or representative of Thermal Arc is authorized to change this warranty in any way or grant any other warranty, and Thermal Arc shall not be bound by any such attempt. Correction of non-conformities, in the manner and time provided herein, constitutes fulllment of thermal’s obligations to purchaser with respect to the product.

This warranty is void, and seller bears no liability hereunder, if purchaser used replacement

parts or accessories which, in Thermal Arc’s sole judgment, impaired the safety or performance of any Thermal Arc product. Purchaser’s rights under this warranty are void if the product is sold

to purchaser by unauthorized persons.

The warranty is effective for the time stated below beginning on the date that the authorized distributor delivers the products to the Purchaser. Notwithstanding the foregoing, in no event

shall the warranty period extend more than the time stated plus one year from the date Thermal Arc delivered the product to the authorized distributor.

Warranty repairs or replacement claims under this limited warranty must be submitted to Thermal Arc via an authorized Thermal Arc repair facility within thirty (30) days of purchaser’s discovery of any defect. Thermal Arc shall pay no transportation costs of any kind under this

warranty. Transportation charges to send products to an authorized warranty repair facility shall be the responsibility of the Purchaser. All returned goods shall be at the Purchaser’s

risk and expense. This warranty dated July 1st 2007 supersedes all previous Thermal Arc warranties. Thermal Arc® is a Registered Trademark of Thermal Arc, Inc.

WARRANTY SCHEDULE

January 2009

SAFETY EQUIPMENT W

ARRANTY PERIOD

ABOR

Auto-Darkening Welding Helmet (Electronic Lens)

2 years 2 years

Harness Assembly

1 month 1 month

ENGINE DRIVEN WELDERS W

ARRANTY PERIOD

ABOR

Scout, Raider, Explorer

Original Main Power Stators and Inductors 3 years 3 years Original Main Power Rectifiers, Control P.C. Boards 3 years 3 years All other original circuits and components including, but not limited to, relays,

switches, contactors, solenoids, fans, power switch semi-conductors 1 year 1 year

Engines and associated components are NOT warranted by Thermal Arc, although most are warranted by the engine

See the Engine Manufactures’

Warranty for Details

GMAW/FCAW (MIG) WELDING EQUIPMENT W

ARRANTY PERIOD

ABOR

Firepower FP-95, FP-125, FP-135, FP-165 Fabricator 140, 180, 190, 210, 251, 281; Fabstar 4030; PowerMaster 350, 350P, 500, 500P, 320SP; 400SP; 500SP; Excelarc 6045. Wire Feeders; Ultrafeed, Portafeed

Original Main Power Transformer and Inductor 5 years 3 years Original Main Power Rectifiers, Control P.C. Boards, power switch semi-conductors 3 years 3 years All other original circuits and components including, but not limited to, relays,

switches, contactors, solenoids, fans, electric motors. 1 year 1 year

GTAW (TIG) & MULTI-PROCESS INVERTER WELDING EQUIPMENT W

ARRANTY PERIOD

ABOR

160TS, 300TS, 400TS, 185AC/DC, 200AC/DC, 300AC/DC, 400MST, 300MST, 400MSTP

Original Main Power Magnetics 5 years 3 years Original Main Power Rectifiers, Control P.C. Boards, power switch semi-conductors 3 years 3 years All other original circuits and components including, but not limited to, relays,

switches, contactors, solenoids, fans, electric motors. 1 year 1 year

PLASMA WELDING EQUIPMENT W

ARRANTY PERIOD

ABOR

Ultima 150

Original Main Power Magnetics 5 years 3 years Original Main Power Rectifiers, Control P.C. Boards, power switch semi-conductors 3 years 3 years Welding Console, Weld Controller, Weld Timer 3 years 3 years All other original circuits and components including, but not limited to, relays,

switches, contactors, solenoids, fans, electric motors, Coolant Recirculator. 1 year 1 year

SMAW (Stick) WELDING EQUIPMENT W

ARRANTY PERIOD

ABOR

Thermal Arc 95 S

Original Main Power Magnetics 1 year 1 year Original Main Power Rectifiers, Control P.C. Boards 1 year 1 year All other original circuits and components including, but not limited to, relays,

switches, contactors, solenoids, fans 1 year 1 year

160S, 300S, 400S

Original Main Power Magnetics 5 years 3 years Original Main Power Rectifiers, Control P.C. Boards 3 years 3 years All other original circuits and components including, but not limited to, relays,

switches, contactors, solenoids, fans, power switch semi-conductors 1 year 1 year

GENERAL ARC EQUIPMENT W

ARRANTY PERIOD

ABOR

Water Recirculators 1 year 1 year

Plasma Welding Torches 180 days 180 days Gas Regulators (Supplied with power sources) 180 days Nil

MIG and TIG Torches (Supplied with power sources) 90 days Nil Replacement repair parts 90 days Nil

MIG, TIG and Plasma welding torch consumable items Nil Nil

This information applies to Thermal Arc products that were purchased in the USA and Canada.

GLOBAL CUSTOMER SERVICE CONTACT INFORMATION

Thermadyne USA

2800 Airport Road Denton, Tx 76207 USA Telephone: (940) 566-2000 800-426-1888 Fax: 800-535-0557 Email: sales@thermalarc.com

Thermadyne Canada

2070 Wyecroft Road Oakville, Ontario Canada, L6L5V6 Telephone: (905)-827-1111 Fax: 905-827-3648

Thermadyne Europe

Europe Building Chorley North Industrial Park Chorley, Lancashire England, PR6 7Bx Telephone: 44-1257-261755 Fax: 44-1257-224800

Thermadyne Asia Sdn Bhd

Lot 151, Jalan Industri 3/5A Rawang Integrated Industrial Park - Jln Batu Arang 48000 Rawang Selangor Darul Ehsan West Malaysia Telephone: 603+ 6092 2988 Fax : 603+ 6092 1085

Cigweld, Australia

71 Gower Street Preston, Victoria Australia, 3072 Telephone: 61-3-9474-7400 Fax: 61-3-9474-7510

Thermadyne Italy

OCIM, S.r.L. Via Benaco, 3 20098 S. Giuliano Milan, Italy Tel: (39) 02-36546801 Fax: (39) 02-36546840

Thermadyne, China

RM 102A 685 Ding Xi Rd Chang Ning District Shanghai, PR, 200052 Telephone: 86-21-69171135 Fax: 86-21-69171139

Thermadyne International

2070 Wyecroft Road Oakville, Ontario Canada, L6L5V6 Telephone: (905)-827-9777 Fax: 905-827-9797

World Headquarters

Thermadyne Holdings Corporation Suite 300, 16052 Swingley Ridge Road St. Louis, MO 63017 Telephone: (636) 728-3000 FAX:

(636) 728-3010

Email: sales@thermalarc.com

www.thermalarc.com

Thermal Arc 95S Thermal Arc Operating Manual

Specifications and Main Features

Frequently Asked Questions

User Manual