Thermadyne Fabricator 211i, Transmig 200i, Fabricator 252i, Transmig 250i Assembly Instructions Manual

Thermadyne Holdings Corporation
Suite 300, 16052 Swingley Ridge Road
St. Louis, MO 63017, USA

Telephone: [phone] • Fax: [phone]

Email: [e-mail]
www.thermalarc.com

Spool Hub Assembly Installation

The following components are included in this kit.

Item Description Qty

1 Fibre Washer 1

2 Spool Hub 1

3 Flat Washer Large Hole 1

4 Keyed Washer 1

SPOOL HUB ASSEMBLY INSTRUCTIONS

Manual 0-5223

Spool Hub Assembly for

Fabricator 211i & 252i

Transmig 200i & 250i

Part Number: W7005311

Assembly Instructions

5 Spring 1

6 Flat Washer Small Hole 1

7 Trib-lobe Nut 1

8 Retaining Clip 1

1

8

3

7

6

4

5

2

Axle

Art # A-10929

1. Install parts numbered 1 to 6 over the axle in the sequence shown above. Align the flat edge of the Fibre
Washer with the flat edge of the recess in the Spool Hub.

2. Install the Tri-lobe Nut (7) into the Axle through parts numbered 6, 5, 4 and 3.

3. Insert the Retaining Clip (8) into one of the set holes on the Spool Hub (2).

Normally, the Spool Hub Assembly has been installed to the power source as delivered from the fac­tory. These installation procedures are designed for future replacement.

© 2011 by Thermadyne Industries

0-5223 1 December 22, 2011

NOTE

SPOOL HUB ASSEMBLY INSTRUCTIONS

Tri-lobe Nut

Printed in: U.S.A

Wire Spool Installation

1. Remove the Spool Hub Retaining Clip from the spool hub.

2. Place Wire Spool onto the hub, loading it so that the wire will feed off the bottom of the spool as the spool
rotates counter clockwise. Make sure to align the spool alignment pin on the hub with the mating hole in
the wire spool.

3. Replace the Wire Spool Hub Retaining Clip in the set of holes closest to the spool, inner holes for

12.5lb/5.66kg (8"/200mm diameter) spool while outer holes for 33lb/15kg (12"/300mm diameter) spool.

12.5lb / 8”
(5.66kg / 200mm)
Wire Spool

Spool Hub Retaining Clip

33lb / 12”
(15kg / 300mm)

Tri-lobe Nut

Spool Hub Retaining Clip

Wire Spool

Spool Hub Aligenment Pin

Spool Hub Aligenment Pin

Art # A-10933

NOTE

The Hub tension has been pre-adjusted at the factory. However if it is considered necessary, adjust­ment can be made by turning the tri-lobe nut inside the open of the hub. For detailed adjustment, refer
to Wire Reel Brake chapter in section 3 in the operating manual.

CAUTION

Use care in handling the spooled wire as it will tend to “unravel” when loosened from the spool.
Grasp the end of the wire firmly and don’t let go of it.

U.S. Customer Care: 800-426-1888 /

FAX

International Customer Care: 940-381-1212 /

W ORLD HEADQUARTERS : 16052 Swingley R idge Road, Suite 300 • St. Louis, Missouri 63017 U. S.A.

THE AMERICAS EUROPE ASIA/PACIFIC

Denton, TX USA
U.S. Customer Care

Ph: 1-800-426-1888 (tollfree)
Fax: [phone] (tollfree)

International Customer Care

Ph: 1-940-381-1212
Fax: [phone]

© 2010 Thermadyne Industries, Inc. www.thermadyne.com

Miami, FL USA
Sales Office, Latin America

Ph: 1-954-727-8371
Fax: [phone]

Oakville, Ontario, Canada
Canada Customer Care

Ph: 1-905-827-4515
Fax: [phone] (tollfree)

December 22, 2011 2 0-5223

800-535-0557 • Canada Customer Care: 905-827-4515 /

FAX [phone]

•

www.thermalarc.com

A Global Cutting & Welding Market Leader

Chorley, United Kingdom
Customer Care

Ph: [phone]
Fax: [phone]

Milan, Italy
Customer Care

Ph: [phone]
Fax: [phone]

Cikarang, Indonesia
Customer Care

Ph: 6221-8990-6095
Fax: [phone]

Rawang, Malaysia
Customer Care

Ph: [phone]
Fax: [phone]

Melbourne, Australia
Australia Customer Care

Ph: 1300-654-674 (tollfree)
Ph: 61-3-9474-7400
Fax: [phone]

International

Ph: 61-3-9474-7508
Fax: [phone]

FAX

800-588-1714

Shanghai, China
Sales Office

Ph: [phone]
Fax: [phone]

Singapore
Sales Office

Ph: [phone]
Fax: [phone]

™