Thermador T18IF901SP Maintance Manual
USE & CARE GUIDE
Model/Modele/Modelo
T18IF901SP
GUIDE
D’UTILISATION
ET D’ENTRETIEN
MANUAL DE USO
Y CUIDADO
Freezer
Congélateur
Congelador
en-us
en Table of contents
en I nst ruc t i on manual
( Important safety instructions . . . . . . . . . . . . 3
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
About these instructions . . . . . . . . . . . . . . . . . . . . . 3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Risk of explosion. . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Risk of electric shock . . . . . . . . . . . . . . . . . . . . . . . 3
Risk of cold burns . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Risk of Injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Risk of fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Avoiding placing children and vulnerable
people at risk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
State of California Proposition 65 Warnings . . . . . . 4
8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7 Environmental protection . . . . . . . . . . . . . . . 5
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Old appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5 Installation and connection . . . . . . . . . . . . . . 5
Contents of package. . . . . . . . . . . . . . . . . . . . . . . . 5
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the appliance . . . . . . . . . . . . . . . . . . . . . . 5
Check built-in cut-out. . . . . . . . . . . . . . . . . . . . . . . . 5
Side-by-side installation . . . . . . . . . . . . . . . . . . . . . . 5
Saving energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Before using for the first time . . . . . . . . . . . . . . . . . 7
Water connection . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . 7
* Getting to know your appliance . . . . . . . . . . 8
Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operating controls. . . . . . . . . . . . . . . . . . . . . . . . . . 9
Interior fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1 Operating the appliance . . . . . . . . . . . . . . . . 12
Switching the appliance on . . . . . . . . . . . . . . . . . .12
Switching off and disconnecting the
appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the language . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the temperature unit . . . . . . . . . . . . . . . . .12
Setting the temperature. . . . . . . . . . . . . . . . . . . . . 12
Super freezing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Clean lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Switching ice cube production on or off . . . . . . . . 13
Reset water filter counter. . . . . . . . . . . . . . . . . . . . 13
Eco mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Self-test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Setting the brightness of the control panel . . . . . . 13
Switching key press sound on or off . . . . . . . . . . . 14
Setting the key volume . . . . . . . . . . . . . . . . . . . . . 14
Setting the signal tone volume . . . . . . . . . . . . . . .14
Automatic clean lock . . . . . . . . . . . . . . . . . . . . . . 14
Automatic door opening . . . . . . . . . . . . . . . . . . . . 14
Switching the water filter counter on and off. . . . . 15
Theater mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Resetting to the factory settings . . . . . . . . . . . . . . 15
Switching demo mode on or off . . . . . . . . . . . . . . 15
Sabbath mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Home network . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
M Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Door alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Temperature alarm . . . . . . . . . . . . . . . . . . . . . . . . 16
o Home Connect. . . . . . . . . . . . . . . . . . . . . . . . 17
Setting up Home Connect. . . . . . . . . . . . . . . . . . . 17
Connecting the refrigerator to the
Home Connect app . . . . . . . . . . . . . . . . . . . . . . . 18
Installing updates for the Home Connect
software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Customer Service access. . . . . . . . . . . . . . . . . . . 18
Deleting network settings . . . . . . . . . . . . . . . . . . . 18
Switch on or off the connection to the home
WLAN network (Wi-Fi). . . . . . . . . . . . . . . . . . . . . . 18
Information on data protection . . . . . . . . . . . . . . . 19
W Freezer compartment. . . . . . . . . . . . . . . . . . 19
Fully utilizing the freezer volume. . . . . . . . . . . . . . 19
Purchasing frozen food. . . . . . . . . . . . . . . . . . . . . 19
When loading products . . . . . . . . . . . . . . . . . . . . 19
Freezing fresh food. . . . . . . . . . . . . . . . . . . . . . . . 19
Thawing frozen food . . . . . . . . . . . . . . . . . . . . . . . 20
= Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Freezer compartment . . . . . . . . . . . . . . . . . . . . . . 20
D Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning the display . . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning the appliance interior. . . . . . . . . . . . . . . 21
Cleaning the fittings . . . . . . . . . . . . . . . . . . . . . . . 21
Care instructions for stainless steel surfaces . . . . 21
> Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Normal noises . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Preventing noises . . . . . . . . . . . . . . . . . . . . . . . . . 21
9 Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3 Faults – what to do? . . . . . . . . . . . . . . . . . . 22
Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Ice maker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4 Customer service. . . . . . . . . . . . . . . . . . . . . 24
Appliance self-test . . . . . . . . . . . . . . . . . . . . . . . . 24
Repair order and advice on faults . . . . . . . . . . . . 24
2
9 Important safety instructions
READ INSTRUCTIONS - DO NOT DISCARD!
(Important safety instructions
Import ant safet y i nstr ucti ons
READ INSTRUCTIONS - DO NOT DISCARD!
Important safety instructions en-us
Definitions
9 WARNING
Non-observance of this warning could
result in death or serious injuries.
9 CAUTION
Non-observance of this warning could
result in slight or moderately serious
injuries.
NOTICE: Non-observance of this
information could damage the appliance.
Note: This indicates important information and/or tips.
About these instructions
■ Read and follow the operating and
installation instructions. They contain
important information on how to install,
use and maintain the appliance.
■ The manufacturer is not liable if you
disregard the instructions and warnings
in the operating and installation
instructions.
■ Retain all documents for subsequent use
or for the next owner.
Introduction
■ This appliance complies with the relevant
safety regulations for electrical
appliances.
■ The refrigeration circuit has been
checked for leaks.
Risk of explosion
■ Never use electric devices inside the
appliance (e.g. heaters or electric ice
makers).
■ Do not store products which contain
flammable propellants (e.g. spray cans)
or explosive substances in the appliance.
■ Only store high-proof alcohol tightly
closed and standing up.
■ Do not use other means to accelerate the
defrosting process other than those
recommended by the manufacturer.
Risk of electric shock
Improper installations or repairs may put the
user at considerable risk.
■ When installing the appliance, make sure
that the power cord does not get jammed
or is not damaged.
■ If the power cord is damaged,
immediately disconnect appliance from
the power supply.
■ Do not use multiple outlets, extension
leads, or adapters.
■ Before servicing or modifying the
appliance, pull out the power plug or
switch off the circuit breaker.
Before cleaning the appliance, press
main On/Off switch to switch the
appliance off.
Glass shelves or other fittings can be
safely moved while the appliance is
switched on.
■ Never cut through or remove the power
cord's third conductor (earthing
conductor).
■ Never defrost or clean the appliance with
a steam cleaner. The steam may
penetrate electrical parts and cause a
short circuit.
■ The appliance, cable and accessories
should only be repaired or replaced by
the manufacturer, customer services, or
a similarly qualified person.
■ Only use original parts supplied by the
manufacturer.
3
en-us Important safety instructions
9 Important safety instructions
READ INSTRUCTIONS - DO NOT DISCARD!
Risk of cold burns
■ Never put frozen food straight from the
freezer compartment into your mouth.
■ Avoid prolonged contact of skin with
frozen food, ice and the tubes in the
freezer compartment.
Risk of Injury
Containers which contain carbonated drinks
may burst.
Do not store containers which contain
carbonated drinks in the freezer
compartment.
Risk of fire
Portable multi-outlet power strips and
portable power supplies may overheat,
causing a fire.
Never leave portable multi-outlet power
strips or portable power supplies behind the
appliance.
Avoiding placing children and vulnerable people at risk
At risk are:
■ Children,
■ People who have limited physical, mental
or sensory abilities,
■ People who have inadequate knowledge
concerning safe operation of the
appliance.
Risk of suffocation
■ If the appliance features a door lock:
keep the key out of the reach of children.
■ Keep children away from the packaging
and its parts.
Damage
To avoid damage:
■ Do not stand or support yourself on the
base, runners or doors.
■ Keep plastic parts and door seals free of
oil and grease.
■ Pull the power plug – not the power cord.
Weight
The appliance is very heavy. The appliance
should always be transported and set up by
at least 2 people.
~ "Installing the appliance" on page 5
State of California Proposition 65 Warnings
This product may contain a chemical known
to the State of California, which can cause
cancer or reproductive harm. Therefore, the
packaging of your product may bear the
following label as required by California:
Measures:
■ Never allow children to play with the
appliance.
■ Ensure that children and vulnerable
people have understood the hazards.
■ Supervise children who are cleaning and
maintaining the appliance.
4
Intended use en-us
8Intended use
Intended use
Use this appliance
■ only for freezing food and making ice.
■ only in the home and in the home environment.
■ only according to these operating instructions.
This appliance is intended for use at an elevation of
no more than 2000 meters above sea level.
7Environmental protection
Env i r on ment al prot ec t i on
Packaging
All materials are environmentally safe and
recyclable:
■ Dispose of packaging in an environmentally
responsible manner.
■ Please ask your dealer or inquire at your local
authority about current means of disposal.
Old appliances
Valuable raw materials can be reclaimed by
recycling old appliances.
5 Installation and
connection
Install ation and connecti on
Contents of package
After unpacking all parts, check for any damage
during transport.
If you have any complaints, please contact the
dealer from whom you purchased the appliance or
our customer service.
~ "Customer service" on page 24
The delivery consists of the following parts:
■ Built-in appliance
■ Interior fittings (depending on model)
■ Installation material
■ Instruction manual
■ Installation instructions
■ Customer service booklet
■ Warranty enclosure
■ Information on the energy consumption and
noises
Technical data
Refrigerant, cubic capacity and further technical
specifications can be found on the rating plate.
~ "Getting to know your appliance" on page 8
9 WARNING
CHILDREN MAY BECOME LOCKED IN THE APPLIANCE AND SUFFOCATE!
Before disposing of your old appliance:
■ Remove the door.
■ Leave shelves and containers in the
appliance to prevent children from climbing
in.
■ Keep children away from the redundant
appliance.
9 CAUTION
REFRIGERANT AND HARMFUL GASES MAY ESCAPE.
Do not damage the tubes of the refrigeration
circuit or insulation.
1. Pull out the power plug.
2. Cut through the power cord.
3. Have the appliance disposed of properly.
Installing the appliance
Installation location
The weight of the appliance may be up to 460 kg
depending on the model. The base must be
sufficiently stable and should not give. If necessary,
reinforce the floor.
Check built-in cut-out
The cut-out must fulfill these criteria:
■ Anti-tilt bracket must be fitted
■ Cut-out depth min. 24” (610 mm), for flush
installation 25” (635 mm)
■ rectangular
■ stable – the side panels and the top must be min.
5/8" (16 mm) thick and securely attached to the
floor or wall
■ Depth of shortest side panels min. 4” (100 mm)
Side-by-side installation
Observe the specifications in the installation
instructions for a side-by-side installation.
If a partition wall is required between the appliances
it must be at least 5/8" (16 mm) wide.
5
en-us Installation and connection
Saving energy
If you follow the instructions below, your appliance will use less power.
Note:
The arrangement of the fittings does not affect the energy consumption of the appliance.
Installing the appliance
Keep the appliance out of direct sunlight. The appliance needs to cool less frequently at low ambient temperaInstall the appliance as far away as possible from heating elements,
cooker and other heat sources:
At least 1¼” (3 cm) from electric or gas cookers.
At least 11¾" (30 cm) from oil or solid-fuel cookers.
Select an installation location at a room temperature of approx. 68 °F
(20 °C).
Do not cover or block the ventilation openings. The appliance needs to cool less frequently if the warm air can
Ventilate the room daily.
Using the appliance
Open the appliance door only briefly. The air in the appliance does not warm up so intensely. The appliance
Transport purchased food in a cool bag and place in the appliance
quickly.
Allow warm food and drink to cool down before placing in the appli-
ance.
Thaw frozen food in the refrigerator compartment to utilize the low
temperature of the frozen food.
Always leave a space between the food and the back panel. The air can circulate and the humidity will remain constant.The appliPack food airtight.
Do not cover or block the ventilation openings. The appliance consumes less power if the warm air can escape.
Vacuum the ventilation openings once a year.
tures and therefore consumes less power.
escape and therefore consumes less power.
needs to cool less frequently and therefore consumes less power.
ance needs to cool less frequently and therefore consumes less
power.
--------
6
Installation and connection en-us
Before using for the first time
1. Remove information material, adhesive tape and
protective foil.
2. Clean the appliance.
~ "Cleaning" on page 20
Water connection
9 CAUTION
■ Installation and connection of the appliance
must be carried out by authorized technicians
according to the installation instructions
supplied.
■ To avoid damage to the appliance and to
ensure its proper functioning, it should only be
connected to a drinking water system.
■ To avoid water damage, a shut-off valve must
be installed.
Water pressure of drinking water system
9 CAUTION
To avoid damage to the appliance, a pressure
relief valve must be installed between the
drinking water connection and the tubing,
should the water pressure exceed the
maximum value.
Note: If the water pressure is too low, this will impair the relevant functions of the appliance.
■ Min. 0.2 Mpa (2 bar / 29 psi)
■ Max. 0.8 Mpa (8 bar / 116 psi)
Electrical connection
9 CAUTION
Do not connect the appliance to electronic
energy saver plugs.
Note: You can connect the appliance to mainscontrolled and sine-controlled inverters.
Mains-controlled inverters are used for photovoltaic
systems which are connected directly to the national
grid. Sine-controlled inverters must be used for
isolated applications. Isolated applications, e.g. on
ships or in mountain lodges, are not directly
connected to the national grid.
1. After installing the appliance, wait at least 1 hour
before connecting it to prevent damaging the
compressor.
2. Check that the outlet was installed according to
the regulations and complies with the
requirements.
Requirements for outlets
Outlet with 110 V ... 120 V
Protective conductor 60 Hz
Fuse 10 A ... 16 A
Maximum simultaneous load
Appliance 6 A
3. Connect the appliance to an outlet near the
appliance.
The outlet must also be freely accessible
following installation of the appliance.
9 WARNING
RISK OF ELECTRIC SHOCK!
Never use multiple outlets, extension leads
or adapters.
The appliance must be grounded correctly.
Never cut through or remove the power
cord's third conductor (grounding
conductor).
9 WARNING
RISK OF ELECTRIC SHOCK!
If the power cord is too short, never use
multiple outlets or extension leads.Instead,
please contact Customer Service.
7
en-us Getting to know your appliance
*Getting to know your
appliance
Gett i ng to know your appl i anc e
-
+
0°
Super Freeze
Settings
]
"
(H
P
X
`
h
)"
)*
)2
):
)J
Appliance
( ... H Operating controls
P Main On/Off switch
X Door damper
` Ice maker
h Rating plate
)" Ice cube container
)* Frozen food container
)2 Ventilation opening
): Automatic door opening
)J Particle filter
8
Getting to know your appliance en-us
Operating controls
²
6XSHU)UHH]H
C
( Touch fields
There are sensors under the touch fields.
Touching the symbol calls up the respective
function.
0 Freezer compartment temperature display
Indicates the set temperature in °C/°F.
8 A/@ buttons
Used to change the temperature.
@ " button
Opens the Settings menu.
~ "Settings menu" on page 9
H Super Freeze button
Switches Super Freeze on or off.
6H WWLQJV
#
+
■ Demo mode
■ Sabbath mode
~ "Operating the appliance" on page 12
Interior fittings
(not all models)
Storage compartment
You can remove and adjust the height of the storage
compartments:
1. Lift up the storage compartment and remove.
Settings menu
Press " button to open the menu.
In the Settings menu you will find:
■ Appliance settings
■ Clean lock
■ Ice cube production
■ Water filter counter
■ Eco mode
■ Self-test
■ Sabbath mode (if activated)
~ "Operating the appliance" on page 12
Appliance settings menu
This is how to navigate to the Appliance settings
menu:
1. Press " button.
2. Use ( button to move to the Appliance settings
menu.
3. Open the menu using 8 button.
In the Appliance settings menu you will find the
following sub-menus and setting options:
■ Brightness
■ Key press sound
■ Key volume
■ Signal tone volume
■ Automatic clean lock
■ Automatic door opening
■ Water filter counter
■ Theater mode
■ Temperature unit
■ Language
■ Home network
■ Factory settings
2. When re-inserting, insert hooks on back of
storage compartment at same height to make it
level.
Note: Insert the storage compartment carefully to
avoid scratching the appliance.
Shelf
You can remove and adjust the shelf:
1. Lift shelf and remove.
2. When re-inserting, insert hooks on back of shelf
at same height to make it level.
Note: Insert shelf carefully to avoid scratching the
appliance.
9
en-us Getting to know your appliance
Container
You can remove the container:
■ Press container to the rear,
■ lift the container at the rear and remove.
You can insert the container:
■ Pull out the telescopic rails all the way
■ Place the container on the telescopic rails and
push into the appliance until it engages.
Ice cube container
Note: To avoid damaging the ice cube container,
always empty it if you switch the appliance off for a
prolonged period or if there is a power failure.
This is how to remove the ice cube container:
1. Take out the frozen food container.
Note: If the door opening angle is 90°, you will find it
easier to access the ice cube container by first
removing the frozen food container.
~ "Container" on page 10
2. Lift the ice cube container at the rear and remove.
This is how to re-insert the ice cube container:
1. Take out the frozen food container.
2. Insert the ice cube container in the recess of the
frozen food container provided for this purpose.
10
Getting to know your appliance en-us
Ice maker
9 CAUTION
DAMAGE TO THE APPLIANCE!
Never store bottles or food in the ice cube
container, even for short periods. This can
block and damage the ice maker.
Ice cube production starts as soon as the appliance
has reached the set temperature.
Notes
■ Discard the first 30-40 ice cubes for hygiene
reasons.
■ Ice cube production stops automatically when the
ice cube container is full.
Information about switching ice cube production on
and off
~ "Switching ice cube production on or off"
on page 13
Ice pack
In the event of a power failure or a fault:
■ The ice pack delays the warming of stored frozen
food.
Exchange water filter or replace with bypass cartridge
You can change the water filter, or replace it with a
bypass cartridge. The bypass cartridge can remain
in the appliance permanently: it does not need to be
changed.
Note: After installing a water filter or a bypass cartridge, discard all ice cubes produced over the first 24 hours.
1. Turn the cap of the water filter counter-clockwise.
2. Take the water filter out.
3. Remove the protective cap of the new water filter
or the new bypass cartridge.
4. Take off the cap of the used water filter and put it
on the new water filter or bypass cartridge.
5. Slide the new water filter or bypass cartridge to
the stop in the filter opening.
Note: The cap must be horizontal here.
6. Turn the water filter or bypass cartridge clockwise
to the mark.
Note: If you do not turn the water filter or bypass
cartridge far enough, damage will be caused by
escaping water.
Note: The longest storage time is obtained by placing the ice pack on the food in the top compartment.
You can take out the ice pack to temporarily keep
food cool, e.g. in a cool bag.
Water filter
Change the water filter after 6 months at the latest.
If the ice tastes stale, discard the rest of the ice
cubes and the ones produced over the next
24 hours. If the ice still tastes stale, change the
water filter.
Note: You can also use the appliance without a water filter. Replace the water filter with a bypass cartridge. Switch off the water filter counter. There is no need to change the bypass cartridge.
A new water filter or bypass cartridge can be
obtained from customer service or a specialist
dealer.
7. When installing a water filter: reset water filter
counter.
When installing a bypass cartridge: switch off
water filter counter.
8. Discard ice cubes produced over the first
24 hours.
9. Drain the water out of the used water filter.
Note: You can dispose of the used water filter with
your household garbage.
11
en-us Operating the appliance
1Operating the appliance
Operat i ng the appl i anc e
Switching the appliance on
1. Press the main On/Off switch.
The appliance starts cooling and the light is
switched on when the door is open.
2. Set the required temperature.
~ "Setting the temperature" on page 12
Operating tips
■ When the appliance has been switched on, it may
take several hours until the set temperatures have
been reached. Do not put in any food until the
selected temperature has been reached.
■ The fully automatic NoFrost system ensures that
the freezer compartment remains free of ice.
Defrosting is not required.
■ The front sides of the housing are partly heated
slightly. This prevents condensation in the area
of the door seal.
■ If the freezer compartment door cannot be
immediately re-opened after it has been closed,
wait until the resulting low pressure has
equalized.
Switching off and disconnecting the appliance
Switching off the appliance
Setting the language
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button.
4. Press ( button to move to the menu item
Language.
5. Press : button.
6. Use ( ) buttons to move to the required language.
7. Press 8 button.
The display restarts, and the start screen is
displayed.
Setting the temperature unit
You can choose between the unit °C and °F.
1 ° means 1 °F
1 °C means 1 °C
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button.
4. Use ( button to move to the menu
item Temperature unit.
5. Press : button.
6. Use ( ) buttons to move to the required unit.
7. Press 8 button.
The unit will be changed.
8. Press ; button to exit the menu.
■ Press the main On/Off switch.
The appliance is no longer cooling.
Disconnecting the appliance
9 CAUTION
Deterioration in water quality
The water supply must be turned off 3 hours
before disconnecting. This prevents mold
forming with any unused water.
If you do not use the appliance for a prolonged
period:
1. Turn off the water supply to the appliance and
wait 3 hours.
2. Remove groceries.
3. Press the main On/Off switch.
4. Pull out the mains plug or switch off the fuse.
The appliance is no longer cooling.
5. Empty the ice cube container and clean the
appliance.
~ "Cleaning" on page 20
6. Leave appliance open.
Setting the temperature
Recommended temperature
Freezer compartment: 0 °F (-18 °C)
Freezer compartment
■ Keep pressing @/A button until the display
indicates the required temperature.
Super freezing
Super freezing cools the freezer compartment as
cold as possible.
Switch on super freezing, e.g.:
■ to quickly freeze food right through to the center
■ 4 ... 6 hours before freezing food weighing 2 kg
or more
Note: When super freezing is switched on, increased operating noise may occur.
After approx. 2 ^ days the appliance switches to
normal operation.
Switching super freezing on or off
■ Press ]/\ button.
12
Operating the appliance en-us
Clean lock
You can use this function to switch off the touch
function of the controls for 10 seconds. During this
time you can clean the display.
~ "Cleaning the display" on page 20
1. Press " button to open the Settings menu.
2. Press < button.
The cleaning display appears, and the countdown
starts.
Automatic clean lock
You can use this function to select whether the
automatic clean lock is switched on automatically
when the door is opened.
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button.
4. Press ) button to move to the menu
item Automatic clean lock.
5. To change the setting, press : button.
Switching ice cube production on or off
9 CAUTION
Damage to the appliance!
Never store bottles or food in the ice cube
container, even for short periods. This can
block and damage the ice maker.
Ice cube production starts as soon as the appliance
has reached the set temperature.
Note: Ice cube production stops automatically when the ice cube container is full.
2. Press > button to move to the menu item Reset
water filter counter.
3. Press 8 button to confirm, and confirm the query
again with 8 button.
Note: The water filter counter will not be reset if you abort the query or take longer than 10 seconds to make an input.
Switching the water filter counter on and off
If you have replaced the water filter with a particle
filter, switch the water filter counter off. It is not
needed in this case as the particle filter does not
have to be replaced.
1. Press " button to open the Settings menu.
2. Scroll to the left to the Appliance settings menu.
3. Press 8 button.
4. Press > button to move to the menu item Water
filter counter.
5. To change the setting, press : button.
Eco mode
Eco mode switches the appliance to energy-saving
operation.
The appliance automatically sets the following temperatures:
■ Freezer compartment: +3 °F (-16 °C)
Switching Eco mode on or off
1. Press the " button to open the Settings menu.
2. Use > button to move to the menu item Eco
mode.
3. Press </= button.
The temperature is changed, and the display shows
the new temperature. When Eco mode is switched
off, the recommended temperature is set.
Note: You can also switch Eco mode on or off by adjusting the temperature with the +/- buttons.
Self-test
This function can be used to start fault analysis on
your appliance.
~ "Appliance self-test" on page 24
Setting the brightness of the control panel
Switching ice maker on or off
1. Press " button to open the Settings menu.
2. Use ) button to move to the menu item Ice cube
production.
3. Press </= button.
Reset water filter counter
After replacing the water filter, you have to reset the
water filter counter.
1. Press " button to open the Settings menu.
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button.
4. Press : button to open the menu
item Brightness.
5. Press ( ) buttons to set the required brightness.
6. Press 8 button.
The setting is saved.
7. Press ; button to exit the menu.
13
en-us Operating the appliance
Switching key press sound on or off
You can switch the sounds generated when pressing
keys off and back on again.
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button to open the menu item.
4. Press ) button to move to the menu item Key
press sound.
5. Press : button to open the menu item.
6. Use ( ) buttons to select the required setting.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Setting the key volume
You can adjust the volume level of the sounds
generated when pressing keys.
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button to open the menu item.
4. Use ) button to move to the menu item Key
volume.
5. Press : button to open the menu item.
6. Use ( ) buttons to select the required setting.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Automatic door opening
The automatic door opening function supports you in
opening the door.
As soon as you activate this function, automatic door
opening moves out and supports you in opening the
door.
9 CAUTION
Repeatedly closing the door too early will cause
automatic door opening to fail or wear out.
Do not close the door as long as automatic
door opening is still moved out.
If you have nevertheless closed the door, leave
it closed for 5 minutes. Automatic door opening
will re-adjust itself.
Open menu item Auto door opening:
1. Press " button to open the main menu.
2. Use ( button to move to the Appliance settings
menu.
3. Press 8 button to open the menu.
4. Press ) button to move the menu item Auto door
opening.
5. To change the setting, press : button.
Switching on Push-to-open system
In an installation situation without handles you can
select the Push-to-open system. Your appliance will
then open a crack if you press lightly on the door.
Note: Please note that automatic door opening is disabled if Sabbath mode is activated.
Setting the signal tone volume
You can adjust the volume level of the signal tones
generated e.g. with alarms.
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button to open the menu item.
4. Use ) button to move to the menu item Signal
tone volume.
5. Press : button to open the menu item.
6. Use ( ) buttons to select the required setting.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Automatic clean lock
You can use this function to select whether the
automatic clean lock is switched on automatically
when the door is opened.
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button.
4. Press ) button to move to the menu
item Automatic clean lock.
5. To change the setting, press : button.
1. Open menu item Auto door opening.
2. Select menu item Push-to-open system.
3. Press 8 button to open the menu item.
4. Select Opening force.Here you can select the
level of force required to activate automatic door
opening.
5. Select Opening duration.Here you can select
how long the door should remain open a crack
before it closes again automatically.
Note: If the door only remains open a crack, the
appliance checks once a second whether the door
is still ajar.After the selected opening duration
elapses, the appliance will close the door
automatically.
Switching on Pull-to-open system
In an installation situation with handles you can
select the Pull-to-open system. Your appliance will
support you in opening the door as soon as you pull
on the handle.
1. Open menu item Auto door opening.
2. Select menu item Pull-to-open system.
3. Press 8 button to open the menu item.
4. Select Opening force.Here you can select the
level of force required to activate automatic door
opening.
Switching off automatic door opening
1. Open menu item Auto door opening.
2. Select menu item Off.
14
Operating the appliance en-us
Switching the water filter counter on and off
If you have replaced the water filter with a particle
filter, switch the water filter counter off. It is not
needed in this case as the particle filter does not
have to be replaced.
1. Press " button to open the Settings menu.
2. Scroll to the left to the Appliance settings menu.
3. Press 8 button.
4. Press > button to move to the menu item Water
filter counter.
5. To change the setting, press : button.
Theater mode
If Theater mode is switched on, the light will slowly
become brighter when the appliance is opened, and
then slowly darker when it is closed.
Switching Theater mode on or off
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button to open the menu item.
4. Use ) button to move to the menu item Theater
mode.
5. Press : button to open the menu item.
6. Use ) button to move to the menu item On or Off.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Resetting to the factory settings
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button.
4. Use ( button to move to the menu item Factory
settings.
5. Press : button.
A signal tone sounds, and a prompt to confirm
reset appears.
6. Press 8 button.
All settings are reset to the factory settings.
7. Press ; button to exit the menu.
Switching demo mode on or off
The cooling function of the appliance is switched off.
All other functions can be used.
Note: Do not store any food items in demo mode as the appliance remains at room temperature.
1. Press " button to open the Settings menu.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button.
4. Use ( button to move to the menu item Demo
mode.
5. Press : button.
6. Use ( ) buttons to select the setting On or Off
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Sabbath mode
All non-essential functions are switched off so you
can also use the appliance on the Sabbath.
The appliance switches off the following:
■ Automatic door opening
Note: With handle-free installation, please note that
you will not be supported when opening the door
during this time. To open the door in this case,
reach from below under the bottom panel of the
unit.
■ Ice maker
■ Audible signals
■ Interior light
■ Messages on the display
■ Background illumination of display is reduced
Switching Sabbath mode on or off
Displaying Sabbath mode in the Settings menu
To use Sabbath mode, you first have to display the
function in the Settings menu:
1. Press " button to open the Settings menu.
2. Use ( button to move to the Appliance settings
menu.
3. Press 8 button.
4. Use ( button to move to the menu item Sabbath
mode.Press : button.
5. Use ( button to move to the menu
item Available.Confirm by pressing 8 button.
6. Press ; button to exit the menu.
The function is added to the Settings menu.
Switching on Sabbath mode
1. Press " button to open the Settings menu.
2. Press › button to open the view Duration
Sabbath mode.
3. Select one of the presettings, or change the
duration with A/@ buttons.
4. Press < button to start.
The appliance switches all listed functions off.
Switching Sabbath mode off
■ After the selected time elapses, the appliance
switches over to normal operation.
■ To end Sabbath mode before the selected time
elapses, press = button.
Home network
You can use this function to establish a connection
between the refrigerator and your mobile device.
~ "Home Connect" on page 17
15
en-us Alarm
MAlarm
Al a r m
Door alarm
If the appliance door is open for a long time, the
door alarm switches on. A message appears on the
control panel.
Switching off the door alarm
■ Close the door.
Note: To mute the door alarm, you only have to acknowledge the message on the control panel. If the door remains opens a few more minutes, the message will appear again.
Temperature alarm
If the freezer compartment becomes too warm, the
temperature alarm is switched on. A message
appears on the control panel. The message shows
the warmest temperature reached in the freezer
compartment.
9 CAUTION
DURING THE THAWING PROCESS, BACTERIA MAY DEVELOP AND SPOIL THE FROZEN ITEMS.
Do not refreeze partly or completely thawed
food.
Refreeze food only after cooking. No longer
store the frozen items for the maximum storage
period.
Note: The alarm may be actuated without risk to the food in the following cases:
■ The appliance is put into service and does not yet
contain any food.
■ Large quantities of fresh food are placed in the
appliance.
■ The freezer compartment door has been open
too long.
Switching off the temperature alarm
1. Check that the cause of the temperature alarm
has been eliminated.
2. Press 8 button to acknowledge the message.
The message disappears. The control panel
again indicates the temperature selected.
From this time on the warmest temperature is
recalculated and saved.
16
Home Connect en-us
o Home Connect
Home Connect
This appliance is Wi-Fi-capable and can be
controlled remotely using a mobile device.
Note: Wi-Fi is a registered trade mark of the Wi-Fi Alliance.
In the following cases, the appliance functions like a
refrigerator without a network connection and can
still be operated manually via the controls:
■ The appliance is not connected to a home
network.
■ The availability of the Home Connect function
depends on the availability of Home Connect
services in your country. Home Connect services
are not available in every country. You can find
more information on www.home-connect.com.
Note: Please observe the safety information in this instruction manual. Ensure that this is also observed if you operate the appliance via the Home Connect app and are not at home when doing so.
~ "Important safety instructions" on page 3
Follow the instructions in the Home Connect app as
well.
The appliance has a wireless transmitting module,
via which the intelligent function of the appliance is
realized. The CMIIT ID of the appliance is shown in
the rating plate.
Setting up Home Connect
Notes
■ Wait at least 2 minutes after switching on the
appliance before setting up Home Connect. Only
then is internal appliance initialization complete.
■ Take note of the Home Connect supplementary
sheet, which is supplied with the appliance or is
available for download at www.thermador.com
together with the instructions. Enter the E-number
of your appliance in the search field.
You can connect your appliance to the home WLAN
network (Wi-Fi) in 3 basic steps.
1. Install the app.
2. Connect your refrigerator to the home WLAN
network (Wi-Fi).
3. Connect the refrigerator to the Home Connect
app.
The first time you open the menu, you will be
automatically guided through initial setup. Follow the
instructions on the control panel. For further
information, please also see the following chapters.
The following sub-menus can be found in the Home
network menu:
■ Connection
■ Connect to app
■ Software update
■ Delete network settings
Open WiFi menu
1. To open the Settings menu, press the " button.
2. Use ( button to move to the menu item Appliance
settings.
3. Press 8 button.
4. Press ( button to move to the menu item WiFi.
5. Press : button.
Note: The first time you open the menu, you will be
automatically guided through initial setup. Follow the
instructions on the control panel.
Setting up the connection to the home network
The first time you open the menu, you will be
automatically guided through initial setup. Follow the
instructions on the control panel.
1. Install the Home Connect app on your mobile
device.
2. Open the Home network menu on your
refrigerator.
3. Open the app on your mobile device.
4. Log in or register with the app if access is not yet
available.
5. Check the router of your home network to see if a
WPS function is available for automatic
connection.
6. If this function is available, start automatic
network connection with 8 button.
Follow the instructions on the control panel.
7. Start manual network connection if this function is
not available, if you're not sure whether the
function is available, or if automatic network
connection failed.
The refrigerator temporarily generates its own
network for connecting the mobile device.
8. Start manual network connection in the app of
your mobile device.
As soon as the refrigerator is connected to the
mobile device, a connection between the refrigerator
and your home network is established.
Note: If the connection cannot be established, check whether there is sufficient reception.
~ "Verifying signal strength" on page 17
Verifying signal strength
The signal strength is displayed in the start window
of the Home network menu.The signal strength
should be at least 50 %. If the signal strength is too
weak, the connection may be interrupted.
Improving signal strength
■ Place the router closer to the refrigerator.
■ Check that screening walls do not interfere with
the connection.
■ Install a repeater to make the signal stronger.
17
en-us Home Connect
Connecting the refrigerator to the Home Connect app
Use this menu to connect your refrigerator to mobile
devices.
1. Install the Home Connect app on your mobile
device and log in or register.
2. Open the Home network menu on your
refrigerator.
3. Press ) button to move to the menu item Connect
to app.
4. Press : button to open the menu item.
5. Confirm the message to display the refrigerator in
the app.
6. Open the app and wait until the refrigerator is
displayed.
Press Add to confirm the connection between the
app and the refrigerator.
If the refrigerator is not automatically displayed,
click on Add appliance in the app and follow the
instructions. As soon as your refrigerator is
displayed, add it with +.
7. Follow the instructions in the app until the
process is complete.
Installing updates for the Home Connect software
The refrigerator checks at regular intervals whether
updates are available for the Home
Connect software.
The Info @ button is visible when an update is
available.
Installing the update:
1. Press @ button.
A note window with the necessary steps for
installing the new software appears.
2. Press 8 button to close the note.
3. Open the Home network menu on your
refrigerator.
4. Press ) button to move to the menu
item Software update.
5. Press : button to open the menu item.
Note: The : button is only visible if an update is
available.
The software is installed.
6. A note appears when installation is complete.
7. Press 8 button to close the note.
Customer Service access
If you contact Customer Service, they can access
your appliance and view its status after you have
given your consent. You need to have your
appliance connected to your home network for this.
Further information about Customer Service access
and its availability in your country is available under
www.home-connect.com in the Help & Support area.
1. Contact Customer Service.
~ "Customer service" on page 24
2. Confirm the start of Customer Service access in
the app.
During Customer Service access the symbol Ù
appears on the control panel.
3. As soon as Customer Service has obtained the
necessary data, they end access.
Note: You can interrupt remote diagnosis early by
switching off Customer Service access in the Home
Connect app.
Deleting network settings
If there is a problem when trying to establish a
connection, or if you would like to register the
appliance in a different home network (WLAN), the
Home Connect settings can be reset.
1. Open the Home network menu on your
refrigerator.
2. Press ) button to move to the menu item Delete
network settings.
3. Press : button to open the menu item.
4. Confirm the message to delete the network
settings.
To then reconnect the appliance to the home
network, perform initial setup again.
~ Page 17
Switch on or off the connection to the home WLAN network (Wi-Fi)
1. Open the WiFi menu on your refrigerator.
~ "Open WiFi menu" on page 17
Note: The first time you open the menu, you will be
automatically guided through initial setup. Follow the
instructions on the control panel.
2. To open the menu item, press
Connection : button.
3. Use ( ) buttons to select the required setting.
4. To select the setting, press 8 button.
Note: If you switch off the Home Connect
connection, you will no longer be able to operate the
appliance with your mobile device.
18
Freezer compartment en-us
Information on data protection
The first time your Home Connect appliance is
registered on a WLAN home network connected to
the Internet (Wi-Fi), your appliance will transmit the
following types of data to the Home Connect server
(initial registration):
■ Unique appliance identification (consisting of
appliance codes as well as the MAC address of
the installed Wi-Fi communication module).
■ Security certificate of the Wi-Fi communication
module (to ensure a secure data connection).
■ The current software and hardware version of
your domestic appliance.
■ Status of any previous resetting to factory
settings.
This initial registration prepares the
Home Connect functions for use and is only required
when you want to use these
Home Connect functions for the first time.
Note: Please note that the Home Connect functions can be utilized only in conjunction with the Home Connect app. Information on data protection can be called up in the Home Connect app.
Purchasing frozen food
■ Ensure the packaging is not damaged.
■ Check there is a sell-by date.
■ The temperature in the supermarket freezer must
be 0 °F (-18 °C) or lower.
■ Do not interrupt the freezing chain. If possible,
transport frozen food in a cool bag and place in
the freezer compartment quickly.
When loading products
■ Freeze large quantities of food in the top
compartment.
This is where it will freeze especially quickly and
gently.
■ Distribute food in the compartments or frozen
food containers.
■ Do not bring food which is to be frozen into
contact with frozen food.
If required, restack frozen food in the frozen food
containers.
■ Important for unrestricted air circulation in the
appliance:
push in frozen food containers up to the limit
stop.
WFreezer compartment
Freez er compar t ment
The freezer compartment is suitable for:
■ storing frozen food
■ making ice cubes
■ freezing food
The temperature can be set from -11 °F (24 °C)... +7 °F (-14 °C).
The freezer compartment can be used to store
perishable foods long-term almost without any
noticeable reduction in quality, as the low
temperatures considerably slow down or stop
deterioration. Appearance, flavor and all valuable
ingredients are largely retained.
The time between putting fresh food in the freezer
compartment and it freezing solid depends on the
following factors:
■ temperature set
■ type of food
■ amount of food in the freezer compartment
■ quantity and type of storage
Fully utilizing the freezer volume
Freezing fresh food
Freeze only fresh and undamaged food.
Food which is boiled, fried or baked is more suitable
for freezing than food which is eaten raw.
Before freezing food, make preparations appropriate
to the food in order to retain the best possible
nutritional value, flavor and color:
■ Vegetables: wash, chop, blanch.
■ Fruit: wash, pit and perhaps peel, possibly add
sugar or ascorbic acid solution.
Information on how to do this can be found in
relevant literature.
Suitable for freezing
■ Baked goods
■ Fish and seafood
■ Meat
■ Poultry and game
■ Vegetables, fruit and herbs
■ Eggs without shells
■ Dairy products, e.g. cheese, butter and quark
■ Ready meals and leftovers, e.g. soups, stews,
cooked meat and fish, potato dishes, soufflés and
desserts
To place the maximum quantity of frozen food in the
freezer compartment:
■ Remove all fittings.
■ Store food directly on the shelves and on the floor
of the freezer compartment.
19
en-us Defrosting
Not suitable for freezing
■ Types of vegetables which are usually eaten raw,
e.g. lettuce or radishes
■ Unpeeled or hard-boiled eggs
■ Grapes
■ Whole apples, pears and peaches
■ Yoghurt, soured milk, sour cream, creme fraiche
and mayonnaise
Packing frozen food
The correct type of packaging and material selection
are decisive factors in the retention of the product
quality and prevent the development of freezer burn.
1. Place food in packaging.
2. Remove air.
3. Pack food airtight to prevent it from losing flavor
or drying out.
4. Label packaging with contents and date of
freezing.
Suitable packaging:
■ Plastic foil
■ Tubular foil made of polyethylene (PE)
■ Aluminum foil
■ Freezer containers
Suitable closures:
■ Rubber bands
■ Plastic clips
■ Cold-resistant adhesive tape
Unsuitable packaging:
■ Wrapping paper
■ Greaseproof paper
■ Cellophane
■ Garbage bags and used grocery bags
9 CAUTION
Do not refreeze partly or completely thawed
food. You can only refreeze food once it has
been cooked (boiled or fried).
The frozen food can no longer be stored for the
maximum duration.
=Defrosting
Def r os t i n g
Freezer compartment
The fully automatic NoFrost system ensures that the
freezer compartment remains free of ice. Defrosting
is no longer required.
DCleaning
Cleani ng
9 CAUTION
AVOID DAMAGING THE APPLIANCE AND THE FITTINGS.
■ Do not use abrasive, chloride-based or acidic
cleaning agents or solvents.
■ Do not use scouring or abrasive sponges.
The metallic surfaces may corrode.
■ Never clean the shelves or containers in the
dishwasher.
The parts may become deformed.
Shelf life of frozen food at 0 °F (-18 °C)
Fish, sausage, ready meals, and cakes
up to 6 months
and pastries:
Meat, poultry: up to 8 months
Vegetables, fruit: up to 12 months
Thawing frozen food
The thawing method must be adjusted to the food
and application in order to retain the best possible
product quality.
Thawing methods:
■ in the refrigerator compartment (especially
suitable for animal-based foods such as fish,
meat, cheese, quark)
■ at room temperature (bread)
■ in the microwave (food for immediate
consumption or immediate preparation)
■ in the oven/cooker (food for immediate
consumption or immediate preparation)
Cleaning the display
The change in temperature and humidity can cause
the controls to steam up.
Switch the clean lock on before cleaning.
~ "Clean lock" on page 13
Use a clean micro-fiber cloth for cleaning.
20
Noises en-us
Cleaning the appliance interior
Proceed as follows:
1. Press the main On/Off switch.
2. Take out food and store in a cool location.
Place ice pack (if available) on the food.
3. Clean the appliance with a soft cloth, lukewarm
water and a little pH-neutral washing-up liquid.
9 CAUTION
The rinsing water must not run into the light
or through the drainage hole into the
evaporation area.
4. Wipe door seal with clear water and dry
thoroughly with a cloth.
5. Switch appliance back on and put in food.
Cleaning the fittings
To clean, take the variable parts out of the
appliance.
~ "Interior fittings" on page 9
Care instructions for stainless steel surfaces
>Noises
Noi s e s
Normal noises
Droning: A motor is running, e.g. refrigerating unit,
ventilator.
Bubbling, buzzing or gurgling: Refrigerant is
flowing through the tubes.
Clicking: Motor, switches or solenoid valves are
switching on or off.
Cracking: Automatic defrosting is running.
Preventing noises
Appliance is not level: Align appliance using a
water level. If required, place a little packing
underneath.
Containers, shelves or storage compartments
wobble or stick: Check the removable fittings and
re-insert if required.
9Lighting
When taking care of and cleaning stainless steel
surfaces, use only cleaning agents suitable for
stainless steel and a stainless steel cleaning cloth.
You can purchase a suitable stainless steel cleaning
cloth from customer service.
To prevent visible scratches, clean the stainless
steel surface in the direction of the structure.
Li ght i ng
Your appliance features a maintenance-free LED
light.
Only customer service or authorized technicians may
repair the light.
21
en-us Faults – what to do?
3 Faults – what to do?
Faul t s – wha t to do?
Before you call customer service, use this table to check whether you can rectify the fault yourself.
Appliance
Temperature differs greatly from the set value.
Switch off appliance for 5 minutes.
~ "Switching off and disconnecting the appliance" on page 12
If the temperature is too warm, check temperature again after a couple of hours.
If the temperature is too cold, check temperature again on the following day.
Displays do not illuminate.
The power plug has not been inserted properly. Connect the power plug.
The fuse has tripped. Check the fuses.
The power has failed. Check whether the power is on.
The refrigeration unit is switching on more frequently and for longer.
The appliance was opened frequently. Do not open the appliance unnecessarily.
The ventilation openings are covered up. Remove obstacles.
Large quantities of fresh food have been put in. Switch on super cooling promptly in advance.
Appliance is not cooling, display and lighting are lit.
Demo mode is switched on. Switch demo mode off.
~ "Switching demo mode on or off" on page 15
The door does not open when pressed.
A special mode has switched off automatic door opening. To open the door, reach from below underneath the bottom panel of
the unit or switch off special mode.
~ "Switching Sabbath mode on or off" on page 15
Pull-to-open is switched on. Switch the appliance to Push-to-open.
~ "Automatic door opening" on page 14
The opening force is set too high. Select a lower setting for the opening force.
~ "Automatic door opening" on page 14
The fuse has tripped. Check the fuses.
The power has failed. Check whether the power is on.
--------
22
Faults – what to do? en-us
Ice maker
The ice maker is not functioning.
Ice cube production is switched off. Switch on ice cube production.
Freezer compartment is too warm. Set the temperature lower.
~ "Operating the appliance" on page 12
Ice cube container is not properly inserted. Insert ice cube container fully.
Ice maker without power. Call customer service.
~ "Customer service" on page 24
No water supply. Check water connection and contact technician if necessary.
Low water pressure. Only connect appliance to pipes with sufficient water pressure.
Kink in water hose. Turn off water supply, straighten out kink. Replace water hose, if nec-
essary.
Too few or deformed ice cubes, water pressure lower than usual.
After switching on or removing many ice cubes, there will be too few
in the ice cube container.
Ice cube production stops even though the ice cube container is still
not full.
Low water pressure. Only connect appliance to pipes with sufficient water pressure.
The water filter is blocked or needs to be replaced. Replace water filter.
Freezer compartment is too warm. Set the temperature lower.
It takes around 24 hours for an empty ice cube container to fill up.
Do not store the ice shovel on the ice in the ice cube container. Otherwise, the sensor will not detect the actual fill level of the container.
~ "Operating the appliance" on page 12
Water is leaking out of the appliance.
Water connection is not tight. Check if the connections are fastened firmly and the water hose is
undamaged.
If the water hose is damaged, contact customer service and have it
replaced. Replacement must be performed by customer service or a
similarly qualified person only.Use original parts supplied by the manufacturer only.
--------
23
Loading...