Thermador PA48WLBSG Installation Manual

Installation

INSTRUCTIONS

Professional Series Pro Grand® Range Low Backguard and Toe Kick Accessory

THERMADOR.COM

Installation

INSTRUCTIONS

Professional Series Pro Grand® Range Low Backguard and Toe Kick Accessory

Models |

English................................................................................................2

Français ..............................................................................................5

Español............................................................................................... 8

Modèles |
Modelos:

PA36JLBG
PA48JLBG
PA48JLBSG
PA60RLBG
PA36JTKG
PA48JTKG
PA60RTKG

THERMADOR.COM

Safety

Installation

DEFINITIONS

9 WARNING

This indicates that death or serious injuries may occur
as a result of non-observance of this warning.

9 CAUTION

This indicates that minor or moderate injuries may
occur as a result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or
property may occur as a result of non-compliance with this
advisory.

Note: This alerts you to important information and/or tips.

Rear clearance

INSTRUCTIONS

For use with the following models:

PRD364WDGx PRD48WCSGx PRG364WDG
PRD364WIGx PRD48WDSGx PRG364WLG
PRD364WLGx PRD48WISGx PRG366WG
PRD366WGx PRD48WLSGx PRG486WDG
PRD484WCGx PRD606WCG PRG486WLG
PRD486WDGx PRD606WCSG
PRD486WIGx PRD606WEG
PRD486WLGU PRD606WESG

State of California Proposition 65 Warning:
: WARNING

This product can expose you to chemicals including
vinyl chloride, which is known to the State of California
to cause cancer and birth defects or other
reproductive harm. For more information go to

www.P65Warnings.ca.gov.

REQUIREMENTS

• To avoid staining on the back wall, high temperature,
non-porous construction materials suitable for use in a
cooking environment are recommended.

• Models PRD606xx are suitable for 0'' rear clearance to
combustible surfaces.

• All other models:

• When using the included island trim a minimum 6"

(152 mm)* rear clearance is required to a
combustible surface*.

• When installing against a combustible surface, a

Thermador low backguard is required for a 0'' rear
clearance to the combustible surface. A
Thermador low backguard must be purchased
separately.

• A rear clearance to a surface covered in a non-

combustible material (metal, ceramic tile, brick,
marble, or stone)*
Island Trim.

*Clearances of less than 6'' (152 mm) should be approved by the
local codes and/or by the local authority having jurisdiction.

 Clearances from non-combustible materials are not part of the

ANSI Z21.1 scope and are not certified by CSA.

 is 0'' when using the included

9 WARNING

Fingers or hands could get pinched when installing
the backguard. Severe injury could result. Use
extreme caution and wear thick protective gloves to
avoid potential laceration to finger or hand while
sliding the backguard down onto the range.

9 WARNING

To avoid possible burn or fire hazard, a backguard
designed specifically for this appliance must be
installed whenever the appliance is used.

Page. 2

Low backguard installation

To install the low backguard

Tools needed

• T-20 torx head screwdriver or drill

• Protective work gloves

Attach the backguard before sliding the appliance into the
final installed position.

To remove the island trim

1. With a T-20 torx head screwdriver, remove the screws
in the front face of the island trim.

1. Align the low backguard with the range side panel’s
right and left rear corners. The backguard is inserted
inside the guide channels on the back of the range.

2. The backguard’s front face is outside the flange on the
front side of the range.

2. Remove the T-20 torx screws securing the trim to the
side panels and the back panel. Lift up to fully remove.

3. Re-install screws.

Page. 3