Thermador KHS48QS, PA48JBS Installation
Backsplash & Keep Hot
Shelf Installation Guide
Installation methods will vary upon need. Before you begin read these instructions carefully. Observe all local codes and ordinances.
2. The height of the hood will determine the height of
WARNING:
To reduce the risk of fire or injury to persons,
check to make sure all packaging has been
removed from accessory devices before use.
Backsplash Installation
(PA [30,36, 48] JBS)
The backsplash must be installed prior to installing
an overhead hood given that the hood shell covers
the top mounting screws of the backsplash.
the top edge of the backsplash. The backsplash
should be mounted so that the bottom rear edge of
the hood overlaps the backsplash 1
3. Per each wall stud, use (2) of the provided screws to secure both the top and bottom of the backsplash (see Figure 1).
• Due to variable wall stud widths and varying
backsplash widths, in some cases only one
wall stud may be found at the mounting
location.
4. Remove protective plastic.
1
/
” (38mm).
2
Parts Included Tools Needed
(10) 1” (25.4mm)
screws
(1) Backsplash Tape measure
(1) Installation Guide Pencil
• To protect against scratches, leave protective film
on backsplash until after installation is complete.
• If range is already installed, refer to the manufacture’s instructions to disconnect gas and power
supplies. Move range forward to gain access to
rear of unit.
1. Locate and lightly mark wall studs.
• Wall studs are usually installed with a 16” or
24” (406mm or 1372mm) space on center.
Phillips screwdriver
or drill
42” (1070mm)
all Studs
W
30”, 36”, 48”
(760mm, 913mm, 1218mm)
Space screws evenly
across top & bottom
Figure 1: Backsplash Installation
English 1
Installing a Backsplash with a Keep Hot Shelf
2. The height of the hood will determine the height of
the top edge of the backsplash. The backsplash
should be mounted so that the bottom rear edge of
the Keep Hot Shelf overlaps the backsplash 11/2”
(38mm).
3. At the locations indicated in Figure 3, mount the lower shelf brackets included with the Keep Hot Shelf through the Backsplash and into the wall studs.
• Due to variable wall stud widths and varying
backsplash widths, in some cases, only one
wall stud may be found at the mounting
location.
4. Remove backsplash protective covering.
5. Start with the Keep Hot Shelf Installation.
Figure 2: Backsplash with a Keep Hot Shelf
A hood can be installed first if the Backsplash is to
be installed with a Keep Hot Shelf given that the
Keep Hot Shelf covers the top mounting screws of
the Backsplash (Figure 2).
• To protect against scratches, leave protective film
on the backsplash until after installation is complete.
• If range is already installed, refer to the manufacture’s instructions to disconnect gas and power
supplies. Move range forward to gain access to
rear of unit.
1. Locate wall studs.
• Wall studs are usually installed with a 16”
(406mm) or 24” (1372mm) space on center.
Lower Shelf Brackets
Included With Keep Hot Shelf
Figure 3: Backsplash with a Keep Hot Shelf
English 2
Keep Hot Shelf
(KHS [30,36,42,48] QS)
5/8”
(16mm)
Items Included
7
13
/
8
(352mm)
Edge will slide
30”, 36”, 42”, 48”
(762, 914, 1067, 1219mm)
op Rack
T
beneath hood
Folds Up
Clip (x2)
10
1
/
” (257mm)
8
Bottom Rack
”
Clip (x4)
Keep Hot
Rack (x2)
1
13
/2”
(343mm)
Tools Needed
(12) 1” (25.4mm)
(4) 1/2” (12.7mm)
screws
(4) U-Nuts
(2) Top shelf brackets
(4) Lower shelf brackets
(2) Keep hot racks
(1) Keep hot shelf backsplash
(1) Installation guide & template
Tape measure
Phillips screwdriver or drill
Painter’s Tape
Sharp knife or scissors
Pencil
English 3
1. Tape the templates included with the Keep Hot
Shelf to the wall accordingly:
• Tape the sheet titled Left Hand Template to
bottom and left end of hood. Align the bottom
line of hood with the top line of the template.
• Tape the sheet titled Right Hand Template to
bottom and right end of hood. Align the bottom
line of hood with the top line of the template.
• Tape the sheet titled Installation Instruction so
that the arrow at the top of the template aligns
with hood centerline. Align the bottom line of
the hood with the top line of the template.
• Left to right sides of the template must be equal
to length of shelf.
2. Mount the (2) top shelf brackets and the (3) lower
shelf brackets at the locations outlined on the
templates. Secure with the (10) 1” (25.4mm)
screws provided.
3. Cut template out from around the brackets and
remove from the wall. Do not discard template
before the Keep Hot Shelf is completely installed.
4. Insert the (3) U-Nuts onto the (3) lower shelf
brackets.
5. Install the wall plate by setting the corner notches
(back of wall plate) atop the (2) top shelf brackets.
Slide the shelf upwards until the bottom engages
with the (3) lower brackets (Figure 4).
Upper shelf bracket (x2)
Lower shelf bracket (x4)
Notches (x2)
Figure 4: 48” Back of Wall Plate
6. Check if the top is properly secured by pulling the
top section of the shelf from the wall.
7. Secure to bottom of shelf with the (4) 1/2”
(12.7mm) screws provided.
For 48” Keep Hot Shelf
Follow steps 1-6 except use (4) lower brackets which
must be spaced equally 15” (381mm) center-to-center
English 4
Loading...